Jeep Commander 2009 User Manual

0 (0)
Jeep Commander 2009 User Manual

COMMANDER 2009 owner’s manual

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.

Chrysler LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

Copyright © 2008 Chrysler LLC

SECTION

TABLE OF CONTENTS

PAGE

1

2

3

4

5

6

7

8

9

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INTRODUCTION

. . 3

1

 

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. 11

2

 

 

 

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.75

3

 

 

 

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

179

4

 

 

 

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

277

5

 

 

 

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

371

6

 

 

 

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

385

7

 

 

 

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

439

8

 

 

 

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

455

9

 

 

 

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

465

10

 

INTRODUCTION

 

 

 

 

 

 

1

 

 

 

 

 

CONTENTS

 

 

 

 

 

Introduction . . . . . . . . . . . . . . . . .

. . . . . . . . . 4

Warnings And Cautions . . . . . . . . . . . . . . . . . .

8

 

Rollover Warning . . . . . . . . . . . . .

. . . . . . . . . 5

Vehicle Identification Number . . . . . . . . . . . . .

8

 

How To Use This Manual . . . . . . . .

. . . . . . . . . 6

Vehicle Modifications/Alterations . . . . . . . . . . .

9

 

 

4 INTRODUCTION

INTRODUCTION

This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle.

The two-wheel drive utility vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle.

Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, transmission, and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road or

working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive.

As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Refer to “On-Road/Off-Road Driving Tips” in Section 5 of this manual.

This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings.

When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine MOPAR parts, and is interested in your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger cars. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over when some other vehicles may not.

INTRODUCTION 5

Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle 1 control. Failure to operate this vehicle safely may result

in an accident, rollover of the vehicle, and severe or fatal injury. Drive carefully.

Rollover Warning Label

6 INTRODUCTION

Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.

The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:

INTRODUCTION 7

1

8 INTRODUCTION

 

WARNINGS AND CAUTIONS

 

This Owner’s Manual contains WARNINGS against op-

 

erating procedures that could result in an accident or

 

bodily injury. It also contains CAUTIONS against proce-

 

dures that could result in damage to your vehicle. If you

 

do not read this entire manual, you may miss important

 

information. Observe all Warnings and Cautions.

 

VEHICLE IDENTIFICATION NUMBER

 

The Vehicle Identification Number (VIN) is found on a

 

label located on the left front corner of the instrument

 

panel pad, visible from outside of the vehicle through the

 

windshield. This number also appears on the Automobile

VIN Location

Information Disclosure Label affixed to a window on

NOTE: It is illegal to remove the VIN label.

your vehicle. Save this label for a convenient record of

 

your vehicle identification number and optional equip-

 

ment.

 

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.

INTRODUCTION 9

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2

CONTENTS

A Word About Your Keys . . . . . . . . . . . . . . . .

14

Wireless Ignition Node (WIN) . . . . . . . . . . .

14

Integrated Ignition Key . . . . . . . . . . . . . . . .

15

Ignition Key Removal . . . . . . . . . . . . . . . . .

15

Key-In-Ignition Reminder . . . . . . . . . . . . . .

17

Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . .

17

Replacement Keys . . . . . . . . . . . . . . . . . . .

18

Customer Key Programming . . . . . . . . . . . .

19

General Information . . . . . . . . . . . . . . . . . .

20

Vehicle Security Alarm . . . . . . . . . . . . . . . . . .

20

Rearming The System . . . . . . . . . . . . . . . . .

20

To Set The Alarm . . . . . . . . . . . . . . . . . . . .

20

To Disarm The System . . . . . . . . . . . . . . . .

21

Illuminated Entry . . . . . . . . . . . . . . . . . . . . .

21

Remote Keyless Entry . . . . . . . . . . . . . . . . . .

22

To Unlock The Doors . . . . . . . . . . . . . . . . .

22

To Lock The Doors . . . . . . . . . . . . . . . . . . .

24

To Release The Liftgate Flipper Glass . . . . . .

24

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Express Down Window Feature —

 

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .

24

Using The Panic Alarm . . . . . . . . . . . . . . . . .

25

Programming Additional Transmitters . . . . . .

25

Transmitter Battery Service . . . . . . . . . . . . . .

25

General Information . . . . . . . . . . . . . . . . . . .

26

Remote Starting System — If Equipped . . . . . . .

27

How To Use Remote Start . . . . . . . . . . . . . . .

27

Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . .

29

Manual Door Locks . . . . . . . . . . . . . . . . . . .

29

Power Door Locks . . . . . . . . . . . . . . . . . . . .

29

Child Protection Door Lock . . . . . . . . . . . . . .

30

Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31

Power Windows . . . . . . . . . . . . . . . . . . . . . .

31

Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .

34

Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34

Liftgate Flipper Glass . . . . . . . . . . . . . . . . . .

35

Power Liftgate — If Equipped . . . . . . . . . . . .

36

Occupant Restraints . . . . . . . . . . . . . . . . . . . . .

39

Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . .

40

Lap/Shoulder Belt Operating Instructions . . . . 41

Adjustable Upper Shoulder Belt Anchorage . . . 45

Automatic Locking Mode — If Equipped . . . . 45

Energy Management Feature . . . . . . . . . . . . . 46

Seat Belt Pretensioners . . . . . . . . . . . . . . . . .

47

Enhanced Seat Belt Use Reminder System

 

(BeltAlert ) . . . . . . . . . . . . . . . . . . . . . . . . .

47

Seat Belts And Pregnant Women . . . . . . . . . .

48

Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .

48

Driver And Front Passenger Supplemental

 

Restraint Systems (SRS) . . . . . . . . . . . . . . . . .

49

Child Restraints . . . . . . . . . . . . . . . . . . . . . .

61

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

13

 

Engine Break-In Recommendations . . . . . . . . . .

71

 

Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . .

71

 

Transporting Passengers . . . . . . . . . . . . . . . .

71

2

. . . . . . . . . . . . . . . . . . . . . . . . .Exhaust Gas

72

 

Safety Checks You Should Make Inside The

 

 

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

73

 

Periodic Safety Checks You Should Make

 

 

Outside The Vehicle . . . . . . . . . . . . . . . . . . .

74

 

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three of which are detented and one spring-loaded. The detented positions are LOCK, ACC, and ON. The START position is a spring-loaded momentary contact position. When released from the START position, the switch automatically returns to the detented ON position.

Wireless Ignition Node (WIN)

1 — LOCK

2 — ACC (ACCESSORY)

3 — ON

4 — START

Integrated Ignition Key

The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a valet key, which stores in the rear of the RKE transmitter.

The valet key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The valet key is also for locking the glove box. You can keep the valet key with you when valet parking.

To remove the valet key from the RKE transmitter, slide the mechanical latch at the top of the RKE transmitter sideways with your thumb and then pull the key out with your other hand.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

2

Remote Keyless Entry (RKE) Transmitter

NOTE: You can insert the double-sided valet key into the lock cylinders with either side up.

Ignition Key Removal

Place the shift lever in PARK. Turn the ignition key to the LOCK position, and remove the key.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE:

If you try to remove the key before you place the shift lever in PARK, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.

For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time for this feature is programmable. For details, refer to “Key Off Power Delay,” under “Personal

Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.

WARNING!

Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.

CAUTION!

An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended.

Key-In-Ignition Reminder

If you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key.

NOTE: The Key-In-Ignition reminder only sounds when the integrated ignition key is placed in the LOCK or ACC position.

SENTRY KEY

The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses the factory-mated Remote Keyless Entry (RKE) transmitter with integrated key and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation. Therefore, only RKE transmitters that are programmed to the vehicle can be used to start and operate

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

the vehicle. The system will shut the engine off in two seconds if an invalid RKE transmitter is used to start the engine.

After turning the ignition switch to the ON position, the 2 Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check,

it indicates that someone used an invalid RKE transmitter to start the engine. Either of these conditions will result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE:

The Sentry Key Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

Exxon/Mobil Speedpass™, additional RKE transmitters, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the RKE transmitter being used to start the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system.

All of the RKE transmitters provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only RKE transmitters that are programmed to the vehicle electronics can be used to start and operate

the vehicle. Once an RKE transmitter is programmed to a vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the keys from the vehicle and lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of RKE transmitters. Duplication of RKE transmitters may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank transmitter to the vehicle electronics. A blank transmitter is one that has never been programmed.

NOTE: When having the Sentry Key Immobilizer system serviced, bring all vehicle RKE transmitters with you to the authorized dealer.

Customer Key Programming

If you have two valid RKE transmitters with integrated keys, you can program new transmitters to the system by performing the following procedure:

1.Insert the first valid integrated key into the ignition switch and turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Turn the ignition switch to the LOCK position and remove the first key.

2.Insert the second valid integrated key and turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound and the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

3. Insert a blank integrated key into the ignition switch and turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound and the Vehicle Security Light will stop flashing, turn on 2 again for three seconds, and then turn off.

The new integrated key is programmed. The RKE transmitter will also be programmed during this procedure.

Repeat this procedure to program up to eight keys. If you do not have a programmed RKE transmitter with integrated key, contact your authorized dealer for details.

NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

General Information

The Sentry Key system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference that may be received, including interference that may cause undesired operation.

VEHICLE SECURITY ALARM

This Vehicle Security Alarm monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthorized operation. When the alarm is activated, the Vehicle Security Alarm provides both audible and visible signals. The horn, headlights, and tail lights will sound/flash repeatedly for three minutes. If disturbance is still present (driver’s door, passenger door, other doors, ignition) after three minutes, the headlights and tail lights will flash for an additional 15 minutes.

NOTE: The Panic and Security alarms are quite different. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deactivate it.

Rearming The System

If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will rearm itself.

To Set the Alarm

The alarm will set when you use the Remote Keyless Entry (RKE) transmitter to lock the doors and liftgate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the Vehicle Security Light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the

Vehicle Security Alarm is arming. During this 16 second arming period, opening any door or the liftgate will cancel the arming. If the Vehicle Security Alarm successfully arms, the Vehicle Security Light will flash at a slower rate to indicate the alarm is set.

To Disarm the System

To disarm the Vehicle Security Alarm, you will need to press the UNLOCK button on the RKE transmitter or turn the ignition key to the ON position. If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering.

The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the Vehicle Security Alarm will arm unexpectedly. If you remain in the vehicle and lock the doors with the RKE transmitter, once the Vehicle Security Alarm is armed (after 16 seconds), when you pull the door handle to exit,

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

the alarm will sound. If this occurs, press the UNLOCK button on the RKE transmitter to disarm the Vehicle Security Alarm. You may also accidentally disarm the Vehicle Security Alarm by unlocking the driver’s door 2 with the key and then locking it. The door will be locked but the Vehicle Security Alarm will not arm.

ILLUMINATED ENTRY

The interior lights come on when you open any door or use the Remote Keyless Entry (RKE) transmitter to unlock any door. They will remain on for about 30 seconds after all doors are closed then fade to off.

The lights also will fade to off if you turn on the ignition after you close all the doors.

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

REMOTE KEYLESS ENTRY

This system allows you to lock or unlock the doors and liftgate, or activate the panic alarm, from distances up to approximately 66 ft (20 m) using a handheld Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need not be pointed at the vehicle to activate the system.

NOTE: Inserting the RKE transmitter into the ignition switch disables all buttons on that RKE transmitter; however, the buttons on the remaining RKE transmitters will continue to work. Driving the vehicle over 5 mph disables all RKE transmitter buttons, for all RKE transmitters, until the ignition is turned back to OFF/LOCK.

Three-Button RKE Transmitter

To Unlock the Doors

Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

 

 

Remote Key Unlock, Driver Door/All Doors First

For vehicles equipped with the Electronic Vehicle

Press

 

Information Center (EVIC), refer to “Flash Lamps with

This feature lets you program the system to unlock either

 

Lock” under “Personal Settings (Customer-

 

2

the driver’s door, or all doors, on the first press of the

 

Programmable Features)” in the Electronic Vehicle

UNLOCK button on the RKE transmitter. To change the

 

Information Center (EVIC),” in Section 4 of this

 

current setting, proceed as follows:

 

manual.

For vehicles equipped with the Electronic Vehicle

Turn Headlights On with Remote Key Unlock

Information Center (EVIC), refer to “Remote Key

This feature activates the headlights for up to 90 seconds

Unlock” under “Personal Settings (Customer-

when the doors are unlocked with the RKE transmitter.

Programmable Features)” in the “Electronic Vehicle

The time for this feature is programmable on vehicles

Information Center (EVIC),” in Section 4 of this

equipped with the Electronic Vehicle Information Center

manual.

(EVIC). For details, refer to “Headlamp Off Delay” under

Flash Lights with Remote Key Lock

“Personal Settings (Customer-Programmable Features)”

in the “Electronic Vehicle Information Center (EVIC),” in

This feature will cause the turn signal lights to flash when

Section 4 of this manual.

the doors are locked or unlocked with the RKE transmit-

 

 

 

ter. This feature can be turned on or off. To change the

 

 

 

current setting, proceed as follows:

 

 

 

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Lock the Doors

Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal.

Sound Horn with Remote Key Lock

This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or off. To change the current setting, proceed as follows:

For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Sound Horn with Lock,” under “Personal Settings (CustomerProgrammable Features)” in the “Electronic Vehicle Information Center (EVIC),” in Section 4 of this manual.

To Release the Liftgate Flipper Glass

Press the FLIPPER GLASS/TRUNK RELEASE button two times (the second press within 5 seconds of the first press) to open liftgate flipper glass.

WARNING!

Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.

Express Down Window Feature — If Equipped

This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and release the UNLOCK button on the RKE transmitter and then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely.

Using the Panic Alarm

To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.

The Panic Alarm will stay on for three minutes unless you turn it off by either pressing the PANIC button a second time, or drive the vehicle at a speed of 15 mph (24 km/h) or greater.

NOTE:

The interior lights will turn off if you turn the ignition switch to the ACC or ON position while the Panic Alarm is activated. However, the exterior lights and horn will remain on.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

Programming Additional Transmitters

Refer to Sentry Key “Customer Key Programming.”

If you do not have a programmed RKE transmitter, 2 contact your authorized dealer for details.

Transmitter Battery Service

The recommended replacement battery is one CR2032 battery.

NOTE:

Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Do not touch the battery terminals that are on the back housing or the printed circuit board.

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

1. Battery access is through a door located on the rear of the fob. Insert a small, flat blade screwdriver into the slot and gently pry open the access door.

Battery Replacement

1— Battery Access Door

2.Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.

3.Reposition the access door panel over the battery opening and snap into place.

General Information

This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If your Remote Keyless Entry (RKE) transmitter fails to operate from a normal distance, check for these two conditions.

1.A weak battery in the RKE transmitter. The expected life of the battery is a minimum of three years.

2.Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.

REMOTE STARTING SYSTEM — IF EQUIPPED

This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of

328 ft (100 m).

How to Use Remote Start

All of the following conditions must be met before the engine will remote start:

Shift lever in PARK

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

27

 

Doors closed

 

 

Hood closed

 

 

Liftgate closed

 

2

Hazard switch off

Brake switch inactive (brake pedal not pressed)

Ignition key removed from ignition switch

Battery at an acceptable charge level, and

RKE PANIC button not pressed.

To Enter Remote Start Mode

Press and release the REMOTE START button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the

engine will start and the vehicle will remain in the Remote Start mode for a 15 minute cycle.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE:

If an engine fault is present the vehicle will start and then shut down 10 seconds later.

The park lamps will turn on and remain on during Remote Start mode.

For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode.

The engine can be started two consecutive times (two 15 minute cycles) with the RKE transmitter. However, the ignition switch must be cycled to the ON position before you can repeat the start sequence for a third cycle.

To Exit Remote Start Mode Without Driving the Vehicle

Press and release the REMOTE START button one time or allow the engine to run for the entire 15 minute cycle.

NOTE: To avoid unintentional shutdowns, the system will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote Start request.

To Exit Remote Start Mode and Drive the Vehicle

Before the end of 15 minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, prior to the end of the 15 minute cycle, insert the key into the ignition switch and turn the switch to the ON position.

The ignition switch must be in the ON position in order to drive the vehicle.

For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the message “Insert Key/ Turn To Run” will flash in the EVIC until you insert the key. Once inserted, the message “Turn To Run” will flash in the EVIC until you turn the key to run.

Loading...
+ 458 hidden pages