Jeep Patriot 2008 User Manual

0 (0)

2 0 0 8 Patriot

O W N E R ’ S M A N U A L

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don't drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.

Chrysler LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

Copyright © 2007 Chrysler LLC

SECTION

TABLE OF CONTENTS

PAGE

1

2

3

4

5

6

7

8

9

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INTRODUCTION

. . 3

1

 

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 9

2

 

 

 

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.73

3

 

 

 

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

167

4

 

 

 

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

235

5

 

 

 

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

331

6

 

 

 

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

345

7

 

 

 

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

399

8

 

 

 

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

407

9

 

 

 

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

417

10

 

INTRODUCTION

 

 

 

 

 

 

1

 

 

 

 

 

CONTENTS

 

 

 

 

 

Introduction . . . . . . . . . . . . . . . . . .

. . . . . . . . . 4

Warnings And Cautions . . . . . . . . . . . . . . . . . . .

7

 

 

Rollover Warning . . . . . . . . . . . . . . .

. . . . . . . . . 4

Vehicle Identification Number . . . . . . . . . . . . . . .

7

 

How To Use This Manual . . . . . . . . .

. . . . . . . . . 5

Vehicle Modifications/Alterations . . . . . . . . . . . .

8

 

4 INTRODUCTION

INTRODUCTION

This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings.

When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine Mopar parts, and is interested in your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger cars. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over when some other vehicles may not.

Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, rollover of the vehicle, and severe or fatal injury. Drive carefully.

Rollover Warning Label

Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat

INTRODUCTION 5

belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two 1 million annually. In a rollover crash, an unbelted person

is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.

The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:

Jeep Patriot 2008 User Manual

6 INTRODUCTION

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle registration and title.

INTRODUCTION 7

1

Vehicle Identification Number

8 INTRODUCTION

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2

CONTENTS

A Word About Your Keys . . . . . . . . . . . . . . . . . .

12

Ignition Key Removal . . . . . . . . . . . . . . . . . . .

12

Locking Doors With The Key . . . . . . . . . . . . . .

14

Key-In-Ignition Reminder . . . . . . . . . . . . . . . .

14

Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Replacement Keys . . . . . . . . . . . . . . . . . . . . . .

16

Customer Key Programming . . . . . . . . . . . . . .

17

General Information . . . . . . . . . . . . . . . . . . . .

18

Security Alarm System — If Equipped . . . . . . . . .18

To Set The Security Alarm . . . . . . . . . . . . . . . .18

To Disarm The Security Alarm System . . . . . . .19

Security Alarm System Manual Override . . . . . .19

Remote Keyless Entry (RKE)— If Equipped . . . . .19

To Unlock The Doors And Liftgate . . . . . . . . . .20

To Lock The Doors And Liftgate . . . . . . . . . . . .21

Using The Panic Alarm . . . . . . . . . . . . . . . . . .21

To Turn Off “Flash Lights With Lock” . . . . . . . .22

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Programming Additional Transmitters . . . . . . . .

22

General Information . . . . . . . . . . . . . . . . . . . .

24

Transmitter Battery Replacement . . . . . . . . . . .

24

Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

Manual Door Locks . . . . . . . . . . . . . . . . . . . . .

26

Power Door Locks . . . . . . . . . . . . . . . . . . . . .

27

Child-Protection Door Lock System

 

(Rear Doors) — If Equipped . . . . . . . . . . . . . . .

30

Power Windows — If Equipped . . . . . . . . . . . . .

32

Power Window Switches . . . . . . . . . . . . . . . . .

32

Auto Down . . . . . . . . . . . . . . . . . . . . . . . . . .

32

Window Lockout Switch . . . . . . . . . . . . . . . . .

33

Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .

35

Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .

36

Adjustable Upper Shoulder Belt Anchorage . . . .

41

Second Row Center Lap/Shoulder Belt

 

Operating Instructions . . . . . . . . . . . . . . . . . . .

42

Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .

45

Enhanced Driver Seat Belt Reminder System

 

(BeltAlert ) . . . . . . . . . . . . . . . . . . . . . . . . . .

46

Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .

47

Seat Belts And Pregnant Women . . . . . . . . . . . .

48

Driver And Front Passenger Supplemental

 

Restraint System (SRS) - Airbag . . . . . . . . . . . .

48

Event Data Recorder (EDR) . . . . . . . . . . . . . . .

58

Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .

60

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

11

 

 

 

 

Engine Break-In Recommendations . . . . . . . . . . .

69

Safety Checks You Should Make Inside

 

 

Safety Tips

69

The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .

70

 

Periodic Safety Checks You Should Make Outside

 

Exhaust Gas

69

2

The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .

71

 

 

 

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place.

Ignition Key Removal

Manual Transmission

1.Turn the ignition switch to the ACC position.

2.Push the key and cylinder inward and rotate the key to the LOCK position.

3.Remove the key from the lock cylinder.

Vehicle Key

Ignition Key Positions

Automatic Transmission — If Equipped

1.Place the shift lever in PARK.

2.Turn the ignition switch to the ACC position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

3. Push the key and cylinder inward and rotate the key to the LOCK position

4. remove the key from the lock cylinder.

2

 

Ignition Key Positions

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.

WARNING!

Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.

CAUTION!

An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended.

Locking Doors With The Key

You can insert the key with either side up. To lock the door, turn the key rearward. To unlock the door, turn the key forward. Refer to “Body Lubrication” under “Maintenance Procedures” in Section 7.

Key-In-Ignition Reminder

Opening the driver’s door when the key is in the ignition sounds a signal to remind you to remove the key.

NOTE: With the driver’s door open and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function.

SENTRY KEY

The Sentry Key Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses ignition keys that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if someone uses an invalid key to try to start the engine.

NOTE: A key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle.

During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid 2 key to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible.

NOTE:

The Sentry Key Immobilizer System is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Exxon/Mobil Speedpass™, additional Sentry Keys , or any other transponder-equipped components on the same key chain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system.

All of the keys provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key is programmed to a vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the Sentry Keys from the vehicle and lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed.

NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.

Customer Key Programming

If you have two valid Sentry Keys , you can program new Sentry Keys to the system by performing the following procedure:

1.Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code.

2.Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key.

3.Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.

4.Insert a blank Sentry Key into the ignition switch. Turn the ignition switch to the ON position within 60

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete, the Vehicle Security Light will turn on again for three seconds and then 2 turn off.

The new Sentry Key is programmed. The Remote

Keyless Entry (RKE) transmitter will also be programmed during this procedure.

Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key , contact your authorized dealer for details.

NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

General Information

The Sentry Key system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference that may be received, including interference that may cause undesired operation.

SECURITY ALARM SYSTEM — IF EQUIPPED

This Security Alarm System monitors the doors, hood, liftgate, and ignition switch for unauthorized operation.

If something triggers the Security Alarm, the Security Alarm System will sound the horn for 30 seconds and flash the lights for 60 seconds. If the triggering device is not deactivated, the horn will sound again after a five

second delay for another 30 seconds. If the trigger remains present, this cycle will repeat for up to five minutes.

To Set The Security Alarm

1.Remove the key from the ignition switch and get out of the vehicle.

2.Lock the door using either the power door LOCK switch or the Remote Keyless Entry (RKE) transmitter and close all doors.

3.The Security Alarm indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming. During this period, if a door is opened, the ignition switch is turned ON, or the power door locks are unlocked in any manner, the Security Alarm will automatically disarm. After 16 seconds, the Security Alarm indicator light will flash slowly. This shows that the Security Alarm System is fully armed.

To Disarm The Security Alarm System

1.Press UNLOCK on the RKE transmitter.

2.Starting the vehicle with a valid Sentry Key will disarm the Security Alarm. A valid key is one that is programmed to your vehicle. A valid key will disarm the Security Alarm System; an invalid key will allow the engine to run for two seconds and stop.

Security Alarm System Manual Override

The Security Alarm System will not arm if you lock the doors using the manual door lock plunger.

REMOTE KEYLESS ENTRY (RKE)— IF EQUIPPED

This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances up to 66 ft (20 m) using a hand-held Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

2

Three Button RKE Transmitter

NOTE: The line of transmission must not be blocked with metal objects.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Unlock The Doors And Liftgate

Press and release the UNLOCK button on the RKE transmitter once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). Refer to “Turn Headlamps on with Remote Key Unlock” under “Electronic Vehicle Information Center (EVIC)” in Section 4.

NOTE: The system can also be programmed to unlock all doors on the first press of the UNLOCK button. On EVIC equipped vehicles refer to “Remote Unlock Driver’s Door 1st” under “Electronic Vehicle Information Center (EVIC)” in Section 4.

For vehicles not equipped with an EVIC, the system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure:

1.Press and hold the LOCK button on a programmed key fob.

2.Continue to hold the LOCK button at least four seconds, but not longer than 10 seconds, then press and hold the UNLOCK button. A single chime will sound to indicate that this feature has changed.

3.Release both buttons at the same time.

4.Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK buttons on the RKE transmitter.

NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm

activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.

5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.

To Lock The Doors And Liftgate

Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signal lights will flash and the horn will chirp once to acknowledge the lock signal. If desired, the “Sound Horn On Lock” feature can be turned on or off. On EVIC equipped vehicles refer to “Personal Settings” under “Electronic Vehicle Information Center (EVIC)” in Section 4.

For vehicles not equipped with an EVIC, perform the following steps:

1.Press the LOCK button for four to 10 seconds.

2.While the LOCK button is pressed (after four seconds), press the PANIC button. Release both buttons.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

The “Sound Horn On Lock” and “Flash Lamps With Lock” features can be reactivated by repeating this procedure.

2

Using The Panic Alarm

To turn the Panic Alarm feature ON or OFF, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.

The Panic Alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater.

NOTE: When you turn off the Panic Alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system.

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Turn Off “Flash Lights With Lock”

NOTE: The “Flash Lights With Lock” feature can be turned on or off. On EVIC equipped vehicles refer toPersonal Settings under “Electronic Vehicle Information Center (EVIC)” in Section 4.

For vehicles not equipped with an EVIC, perform the following steps:

1.Press the UNLOCK button for four to 10 seconds.

2.While the UNLOCK button is pressed (after four seconds), press the LOCK button. Release both buttons.

3.Test the “flash lights” with LOCK feature, while outside of the vehicle, by pressing the LOCK button on the RKE transmitter with the ignition in the LOCK position and the key removed.

NOTE: Pressing the LOCK button on the RKE transmitter while you are in the vehicle, will activate the Security

Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.

The “Flash Lights With Lock” feature can be reactivated by repeating this procedure.

Programming Additional Transmitters

Vehicles are shipped from the assembly plants with two RKE transmitter programmed only for that vehicle. A total of eight RKE transmitter can be programmed for your vehicle. Additional RKE transmitter can be programmed to your vehicle through the use of a currently programmed RKE transmitter.

NOTE: When entering program mode using that RKE transmitter, all other programmed RKE transmitters will be erased and you will have to reprogram them for your vehicle.

Use the following procedure to program additional RKE transmitters if the vehicle is not equipped with Sentry Key :

1.Enter your vehicle and close all doors.

2.Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this programming procedure).

3.Place the key into the ignition.

4.Turn the ignition to the ON position. Do not start the engine.

5.Press and hold the UNLOCK button on the RKE transmitter.

6.After holding the UNLOCK button for four seconds, also press the PANIC button within six seconds.

7.When a single chime is heard, release both buttons. The chime is an indication that you have successfully

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

entered program mode. All RKE transmitters that are to be programmed must be done so within 60 seconds of when the chime is heard.

8.Using the RKE transmitter to be programmed, press 2 and release both the LOCK and UNLOCK buttons simultaneously.

9.A single chime will be heard.

10.Within four seconds of hearing the chime, press and release the UNLOCK button on the RKE transmitter.

11.A single chime will be heard.

12.Repeat steps 8 through 10 to program up to six additional RKE transmitters.

13.Turn the ignition to the OFF position.

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed RKE transmitters function normally.

NOTE: If you do not have a programmed RKE transmitter, contact your authorized dealer for details.

General Information

This device complies with Part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference that may be received including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If your RKE transmitter fails to operate from a normal distance, check for these two conditions:

1.Weak batteries in the RKE transmitter. The expected life of batteries is five years.

2.Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios.

Transmitter Battery Replacement

NOTE: Perchlorate Material – special handling may apply. See “www.dtsc.ca.gov/hazardouswaste/perchlorate.”

The recommended replacement battery is CR2032.

1. If the RKE transmitter is equipped with a screw, remove the screw. With the RKE transmitter buttons facing down, use a flat blade to pry the two halves of the RKE transmitter apart. Make sure not to damage the elastomer seal during removal.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

2. Remove and replace the batteries. Avoid touching the

 

new batteries with your fingers. Skin oils may cause

 

battery deterioration. If you touch a battery, clean it with

2

rubbing alcohol.

3. To reassemble the RKE transmitter case, snap the two halves together.

NOTE: If the RKE transmitter is equipped with a screw, reinstall and tighten the screw until snug.

Separating RKE Transmitter Halves

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

DOOR LOCKS

Manual Door Locks

Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door.

WARNING!

For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.

WARNING!

When leaving the vehicle, always remove the key from the ignition lock and lock your vehicle. Do not leave unattended children in the vehicle or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.

Manual Door Lock Plunger

CAUTION!

An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended.

Power Door Locks

A power door lock switch is located on the drivers door panel. Press this switch to lock or unlock the doors.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

2

Power Door Lock Switches

Automatic Door Locks — If Equipped

The doors will lock automatically on vehicles with power door locks if all of the following conditions are met:

1.The Auto Lock feature is enabled.

2.The transmission is in gear.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3.All doors are closed.

4.The throttle is pressed.

5.The vehicle speed is above 15 mph (24 km/h).

6.The doors were not previously locked using the power door lock switch or Remote Keyless Entry (RKE) transmitter.

The Automatic Door Lock feature can be enabled or disabled. Refer to “Personal Settings” under “Electronic Vehicle Information Center (EVIC) — (if equipped)” in Section 4.

For vehicles not equipped with the EVIC, the Automatic Door Locks can be enabled or disabled by performing the following procedure:

1.Close all doors and place the key in the ignition.

2.Cycle the ignition switch between LOCK and ON and back to LOCK four times, ending up in the LOCK position.

Ignition Key Position

3.Depress the power door LOCK switch to lock the doors.

4.A single chime will indicate the completion of the programming.

5.Verify reprogramming by driving the vehicle.

Loading...
+ 408 hidden pages