Jeep 2008 Grand Cherokee SRT, 2008 Grand Cherokee Srt8 User Manual

5.6 Mb
Loading...

SECTION

TABLE OF CONTENTS

PAGE

1

2

3

4

5

6

7

8

9

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INTRODUCTION

. . 3

1

 

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 9

2

 

 

 

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.69

3

 

 

 

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

169

4

 

 

 

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

239

5

 

 

 

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

297

6

 

 

 

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

303

7

 

 

 

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

355

8

 

 

 

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

375

9

 

 

 

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

385

10

 

INTRODUCTION

 

 

 

 

 

 

1

 

 

 

 

 

CONTENTS

 

 

 

 

 

m Introduction . . . . . . . . . . . . . . . . . .

. . . . . . . . . 4

m Warnings And Cautions . . . . . . . . . . . . . . . . . . .

7

 

m Rollover Warning . . . . . . . . . . . . . . .

. . . . . . . . . 4

m Vehicle Identification Number . . . . . . . . . . . . . . .

7

 

m How To Use This Manual . . . . . . . . .

. . . . . . . . . 5

m Vehicle Modifications/Alterations . . . . . . . . . . . .

8

 

4 INTRODUCTION

INTRODUCTION

This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings.

When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained technicians and genuine Mopart parts, and is interested in your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance, and a higher center of gravity than many passenger cars. Driven in an unsafe manner, all vehicles can be caused to go out of control. Because of the higher center of gravity, if this vehicle is out of control it may rollover when some other vehicles may not.

Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, rollover of the vehicle, and severe or fatal injury. Drive carefully.

INTRODUCTION 5

Failure to use driver and passenger seat belts provided

is a major cause of severe or fatal injury. In fact, the U.S. 1 government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually. In a rollover crash, an unbelted person

is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section contains the information you desire.

Rollover Warning Label

The detailed index, at the rear of this manual, contains a

 

 

complete listing of all subjects.

 

Consult the following table for a description of the

 

symbols that may be used on your vehicle or throughout

 

this owner manual:

6 INTRODUCTION

 

 

INTRODUCTION 7

WARNINGS AND CAUTIONS

 

 

 

 

 

 

1

This manual contains WARNINGS against operating

 

 

procedures, which could result in an accident or bodily

 

 

 

injury. It also contains CAUTIONS against procedures,

 

 

 

which could result in damage to your vehicle. If you do

 

 

 

not read this entire manual, you may miss important

 

 

 

information. Observe all Warnings and Cautions.

 

 

 

VEHICLE IDENTIFICATION NUMBER

 

 

 

The vehicle identification number (VIN) is found on a

 

 

 

label located on the left front corner of the instrument

 

 

 

panel pad, visible from outside of the vehicle through the

 

 

 

windshield. This number also appears on the Automobile

NOTE: It is illegal to remove the VIN label.

Information Disclosure Label affixed to a window on

 

 

 

your vehicle. Save this label for a convenient record of

 

 

 

your vehicle identification number and optional equip-

 

 

 

ment.

 

 

 

8 INTRODUCTION

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2

CONTENTS

m A Word About Your Keys . . . . . . . . . . . . . . . . . .

12

N Wireless Ignition Node (WIN) . . . . . . . . . . . . .

12

N FOB With Integrated Key (FOBIK) . . . . . . . . . .

13

N Ignition Key Removal . . . . . . . . . . . . . . . . . . .

14

N Key-In-Ignition Reminder . . . . . . . . . . . . . . . .

15

m Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

N Replacement Keys . . . . . . . . . . . . . . . . . . . . . .

16

N Customer Key (FOB) Programming . . . . . . . . . .

17

N General Information . . . . . . . . . . . . . . . . . . . .

18

m Security Alarm System Ð If Equipped . . . . . . . . .

18

N To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .

18

N To Disarm The System . . . . . . . . . . . . . . . . . . .

19

m Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . .

19

m Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . .

19

N To Unlock The Doors . . . . . . . . . . . . . . . . . . .

20

N To Lock The Doors . . . . . . . . . . . . . . . . . . . . .

21

N To Release The Liftgate Flipper Glass . . . . . . . .

22

N Using The Panic Alarm . . . . . . . . . . . . . . . . . .

22

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

N Programming Additional Transmitters . . . . . . . .

23

N Transmitter Battery Service . . . . . . . . . . . . . . .

23

N General Information . . . . . . . . . . . . . . . . . . . .

24

m Remote Starting System Ð If Equipped . . . . . . . .

24

m Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

N Manual Door Locks . . . . . . . . . . . . . . . . . . . . .

26

N Power Door Locks . . . . . . . . . . . . . . . . . . . . .

27

N Child Protection Door Lock . . . . . . . . . . . . . . .

28

m Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29

N Power Windows . . . . . . . . . . . . . . . . . . . . . . .

29

N Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .

31

m Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

N Liftgate Flipper Glass . . . . . . . . . . . . . . . . . . .

33

m Occupant Restraints . . . . . . . . . . . . . . . . .

. . . . .

34

N Lap/Shoulder Belts . . . . . . . . . . . . . . . .

. . . . .

36

N Lap/Shoulder Belt Operating Instructions

. . . . .37

N Adjustable Upper Shoulder Belt Anchorage . . . .

40

N Automatic Locking Mode Ð If Equipped

. . . . .41

N Energy Management Feature . . . . . . . . .

. . . . .

41

N Seat Belt Pretensioners . . . . . . . . . . . . . .

. . . . .

42

N Enhanced Seat Belt Use Reminder System

 

 

(BeltAlert) . . . . . . . . . . . . . . . . . . . . . .

. . . . .

42

N Seat Belts And Pregnant Women . . . . . . .

. . . . .

44

N Seat Belt Extender . . . . . . . . . . . . . . . . .

. . . . .

44

N Driver And Front Passenger Supplemental

 

 

Restraint Systems (SRS) . . . . . . . . . . . . .

. . . . .

45

N Child Restraint . . . . . . . . . . . . . . . . . . .

. . . . .

56

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

11

 

 

 

 

m Engine Break-In Recommendations . . . . . . . . . . .

66

N Safety Checks You Should Make Inside The

 

 

m Safety Tips

66

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

67

 

N Safety Checks You Should Make Outside The

 

 

N Exhaust Gas

66

 

2

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

68

 

 

 

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided integrated key into the ignition switch with either side up.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three of which are detented and one spring-loaded. The detented positions are LOCK, ACC, and ON. The START position is a spring-loaded momentary contact position. When released from the START position, the switch automatically returns to the detented ON position.

Wireless Ignition Node (WIN)

Fob with Integrated Key (FOBIK)

The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a valet key, which stores in the rear of the Fob.

The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead. You can keep the valet key with you when valet parking.

To remove the valet key from the Fob, slide the mechanical latch at the top of the Fob sideways with your thumb and then pull the key out of the Fob with your other hand.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

2

3 Button FOBIK

NOTE: You can insert the double-sided valet key into the lock cylinders with either side up.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Ignition Key Removal

Place the selector lever in ªPº (Park). Turn the key to the LOCK position, and remove the key.

NOTE:

²If you try to remove the key before you place the selector lever in ªPº (Park), it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.

²For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 60 minutes

after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time for this feature is programmable. For details, refer to ªDelay Power Off to Accessories Until Exit,º under ªPersonal Settings (Customer Programmable Features),º under ªElectronic Vehicle Information Center (EVIC)º in Section 4 of this manual.

WARNING!

Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don't leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.

CAUTION!

An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended.

Key-In-Ignition Reminder

If you open the driver's door and the key is in the ignition, a chime will sound to remind you to remove the key.

NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

SENTRY KEY

The Sentry Key Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation 2 is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses the factory-mated Fob with Integrated Key and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation. Therefore, only Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid Fob to start the engine.

After turning the ignition switch to the ON position, the Vehicle Security Alarm Indicator Light will turn on for three (3) seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

flash after the bulb check, it indicates that someone used an invalid Fob to start the engine. Either of these conditions will result in the engine being shut off after two (2) seconds.

If the Vehicle Security Alarm Indicator Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible.

NOTE:

²The Sentry Key Immobilizer System is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

²Exxon/Mobil Speed Pass,™ additional Fobs, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the Fob being used to

start the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system.

All of the Fobs provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove Sentry Keys from the vehicle and lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided with a four-digit PIN number. Keep the PIN in a secure

location. This number is required for dealer replacement of Fobs. Duplication of Fobs may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank Fob to the vehicle electronics. A blank Fob is one, which has never been programmed.

NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle Fobs with you to the dealer.

Customer Key (Fob) Programming

If you have two valid sentry keys, you can program new sentry keys to the system by performing the following procedure:

1. Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

2.Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds, a chime

will sound and the Vehicle Security Alarm Indicator Light will begin to flash. Turn the ignition switch OFF 2 and remove the second key.

3.Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds, a single chime will sound and the Vehicle Security Alarm Indicator Light will stop flashing, turn on again for 3 seconds, and then turn off.

The new Sentry Key is programmed. The Keyless Entry

Transmitter will also be programmed during this procedure.

Repeat this procedure to program up to 8 keys. If you do not have a programmed sentry key, contact your dealer for details.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: If a programmed key is lost, see your dealer to have all remaining keys erased from the systems memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to the dealer at the time of service to be reprogrammed.

General Information

The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:

²This device may not cause harmful interference.

²This device must accept any interference that may be received, including interference that may cause undesired operation.

SECURITY ALARM SYSTEM Ð IF EQUIPPED

This system monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthorized operation and movement inside of the vehicle. When the alarm is activated, the system provides both audible and visual signals. The horn will sound repeatedly for three minutes and the headlights and taillights will flash for an additional 15 minutes.

To Set the Alarm

The alarm will set when you use the remote keyless entry transmitter to lock the doors and liftgate or when you use the power door lock switch while the door is open. After all the doors are locked and closed, a red light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the system is arming. During this 16 second pre-arm period, opening any door or the liftgate will cancel the arming. If the system successfully arms, the red light will flash at a slower rate to indicate the alarm is set. A manual lock of the doors, either with

the door lock plunger located on the inside of the doors or with the driver's door key lock cylinder, will not set the alarm.

To Disarm the System

To disarm the system, use the remote keyless entry transmitter. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering.

The Security Alarm System is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, once the system is armed (after 16 seconds), when you pull the door handle to exit the alarm will sound. If this occurs, press the ªUnlockº button on the remote keyless entry transmitter to disarm the system. The Security Alarm System will not disarm with a manual unlock, either

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

through the lock plunger located on the inside of the door, or through a key in the driver's door key cylinder.

ILLUMINATED ENTRY

2

The interior lights come on when you open any door. They will remain on for about 30 seconds after all doors are closed then fade to off.

The lights also will fade to off if you turn on the ignition after you close all the doors.

REMOTE KEYLESS ENTRY

This system allows you to lock or unlock the doors, liftgate, or activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: Inserting the Fob with Integrated Key into the ignition switch disables all buttons on that transmitter; however, the buttons on the remaining transmitters will continue to work. Shifting the vehicle out of ªPº (Park) disables all transmitter buttons for all Fobs.

3 Button FOBIK

To Unlock the Doors

Press and release the ªUnlockº button on the transmitter once to unlock the driver's door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

Remote Key Unlock, Driver Door/All Doors First

This feature lets you program the system to unlock either the driver's door or all doors on the first press of the ªUnlockº button on the transmitter. To change the current setting, proceed as follows:

²For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to ªRemote Key Unlock,º under ªPersonal Settings (Customer Programmable Features),º under ªElectronic Vehicle Information Center (EVIC)º in Section 4 of this manual for details.

Flash Lights with Remote Key Lock

This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter. This feature can be turned on or off. To change the current setting, proceed as follows:

²For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to ªFlash Lights with Remote Key Lock,º under 9Personal Settings (Customer Programmable Features),º under ªElectronic Vehicle Information Center (EVIC)º in Section 4 of this manual for details.

Turn Headlights On with Remote Key Unlock

This feature activates the headlights for up to 90 seconds when the doors are unlocked with the transmitter. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). For details, refer to ªTurn Headlights On with

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

Remote Key Unlock,º under ªPersonal Settings (Cus-

 

tomer Programmable Features),º under ªElectronic Ve-

 

hicle Information Center (EVIC)º in Section 4 of this

2

manual.

To Lock the Doors

Press and release the ªLockº button on the transmitter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal.

Sound Horn with Remote Key Lock

This feature will cause the horn to chirp when the doors are locked with the transmitter. This feature can be turned on or off. To change the current setting, proceed as follows:

²For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to ªSound Horn with

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Remote Key Lock,º under ªPersonal Settings (Customer Programmable Features),º under ªElectronic Vehicle Information Center (EVIC)º in Section 4 of this manual for details.

To Release the Liftgate Flipper Glass

Press the ªFlipper Glass/Trunk Releaseº button on the transmitter two times to release the flipper glass.

WARNING!

Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.

Using The Panic Alarm

To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.

The panic alarm will stay on for 3 minutes unless you turn it off by either pressing the PANIC button a second time or drive the vehicle at a speed of 15 mph (24 km/h) or greater.

NOTE:

²The interior lights will turn off if you turn the ignition switch to the ACC or ON position while the panic alarm is activated. However, the exterior lights and horn will remain on.

²You may need to be less than 23 feet (7 meters) from the vehicle when using the transmitter to turn off the panic alarm due to the radio frequency noises emitted by the system.

Programming Additional Transmitters

Refer to SENTRY KEY ªCustomer Key (Fob) Programming.º

If you do not have a programmed transmitter, contact your dealer for details.

Transmitter Battery Service

The recommended replacement battery is one CR2032 battery.

NOTE: Perchlorate Material Ð special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

1. Battery access is through a door located on the rear of the FOBIK. Insert a small, flat bladed screwdriver into the

slot and gently pry open the access door.

2

FOBIK Battery Replacement

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2.Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.

3.Reposition the access door panel over the battery opening and snap into place.

General Information

This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions:

²This device may not cause harmful interference.

²This device must accept any interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

If your Remote Keyless Entry (RKE) transmitter fails to operate from a normal distance, check for these two conditions.

1.A weak battery in the transmitter. The expected life of the battery is a minimum of three years.

2.Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.

REMOTE STARTING SYSTEM Ð IF EQUIPPED

Your vehicle may be equipped with a remote starting system, which will allow the vehicle to be started up to 300 feet (91 meters) away from the vehicle using the remote keyless entry key fob which is part of your ignition key.

In order to remote start your vehicle, the hood, liftgate, and all of the doors must be closed.

To remote start your vehicle, press the ªRemote Startº button on the key fob twice within three seconds. To indicate that the vehicle is about to start, the parking lights will flash and the horn will sound briefly (if programmed). To turn the horn on or off, refer to ªElectronic Vehicle Information Center/Customer Programmable Features/Sound Horn With Lock?º in Section 4 of this manual.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

Once the vehicle has started, the engine will run for 15 minutes. To cancel remote start, press the ªRemote Startº button once.

The parking lamps will remain illuminated to indicate 2 that the vehicle has remote started and the engine is running. The lamps will turn off when the ignition is turned to ON or the remote start is cancelled.

To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the ªUnlockº button on the key fob. After the vehicle is unlocked, you have 15 minutes to enter the vehicle, insert the key into the ignition, and turn it to the ON position. A ªInsert Key/Turn To Onº message will display in the Electronic Vehicle Information Center (EVIC) until the ignition switch has been turned to the ON position.

Otherwise, the engine will cancel remote start and automatically turn off.

Remote Start Button

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Remote start will also cancel if any of the following occur:

²If the engine stalls or RPM exceeds 2500

²Any engine warning lamps come on

²The hood is opened

²The hazard switch is pressed

²The transmission is moved out of P (Park).

²The brake pedal is pressed.

The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the Vehicle Theft Alarm is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition and moving it to the ON position, then back to LOCK.

DOOR LOCKS

Manual Door Locks

Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.

WARNING!

²For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle.

²When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

Power Door Locks

 

If you press the door lock switch while the keys are in the

The power door lock switch is located on each front door

ignition switch, and the driver's door is open, the doors

panel. Press the switch to lock or unlock the doors.

will not lock.

 

2

 

The rear doors cannot be opened from inside the vehicle

 

 

 

until you pull up the lock plungers.

 

Automatic Door Locks

 

If this feature is selected your door locks will lock

 

automatically if the vehicle speed is above 15 mph (24

 

km/h) and all doors are closed. It will reset whenever a

 

door is opened.

 

This feature is selectable and can be turned on or off.

 

Refer to ªElectronic Vehicle Information Center (EVIC) Ð

 

Customer Programmable Featuresº in Section 4 of this

Power Door Lock Switch

manual or see your authorized dealer.

 

 

 

If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.

Automatic Unlock on Exit Feature Ð Only Available if Auto Lock is Enabled

This feature will unlock all the doors when the driver's door is opened if the vehicle is stopped and in P (Park) or

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

N (Neutral). Refer to ªElectronic Vehicle Information Center (EVIC) Ð Customer Programmable Featuresº in Section 4 of this manual or see your authorized dealer.

Child Protection Door Lock

The rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks.

WARNING!

Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.

Child Protection Door Lock

WINDOWS

Power Windows

The power window controls are located on the driver's door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACC position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29

2

Power Window Switches

The power window switches remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature.

Auto Down

Both the driver and front passenger window switch has an ªAuto Downº feature. Press the window switch past

30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

the first detent, release, and the window will go down automatically. To cancel the ªAuto Downº movement, operate the switch in either the up or down direction and release the switch.

To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly.

To open the window part way, press to the first detent and release it when you want the window to stop.

The power window switches remain active for 10 minutes after the ignition has been turned off. Opening either front door will cancel this feature.

Auto Up Feature with Anti-Pinch Protection (Driver's and Front Passenger Door Only)

Lift the window switch to the second detent, release, and the window will go up automatically.

To stop the window from going all the way up during the auto-up operation, push down on the switch briefly.

To close the window part way, lift the window switch to the first detent and release when you want the window to stop.

NOTE: If the window runs into any obstacle during the auto-closure it will reverse direction and then stop. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road conditions may trigger the auto reverse function unexpectedly during auto closure. If this happens pull the switch lightly to the first detent and hold to close the window manually.

WARNING!

There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing.

Resetting the Auto-Up Feature

Should the Auto-Up feature stop working the window probably needs to be reset. To reset Auto-Up:

Pull the window switch up and close the window completely, then pull and hold the switch for 1 second.

Window Lockout Switch

The window lockout switch on the driver's door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lockout button. To enable the window controls, press the window lockout button again.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31

2

Power Window Lock

Wind Buffeting

Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain

32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.

LIFTGATE

To open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate.

Liftgate Release

WARNING!

Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.

Liftgate Flipper Glass

The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33

2

Liftgate Glass Release

WARNING!

To avoid injury stand back when opening. Glass will automatically rise.

34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Once the liftgate flipper glass has been opened, connection to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open.

NOTE: If a power malfunction to the power liftgate latch should occur, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel.

WARNING!

Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.

OCCUPANT RESTRAINTS

Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and right front passenger, and window bags for the driver and passengers seated next to a window. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems.

NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity.

Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.

WARNING!

In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35

Buckle up even though you are an excellent driver, even

 

on short trips. Someone on the road may be a poor driver

 

and cause a collision which includes you. This can

2

happen far away from home or on your own street.

Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times to reduce or prevent injuries.

36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Lap/Shoulder Belts

All seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out.

WARNING!

²Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too.

²Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.

Lap/Shoulder Belt Operating Instructions

1.Enter the vehicle and close the door. Sit back and adjust the seat.

2.The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37

2

Latch Plate

38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a ªclick.º

Latch Plate To Buckle

WARNING!

A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.

A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.

A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren't as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision.

A shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.

4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.

WARNING!

A lap belt worn too high can increase the risk of injury in a collision. The belt forces won't be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug.

A twisted belt can't do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can't straighten a belt in your vehicle, take it to your authorized dealer and have it fixed.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39

5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor

will withdraw any slack in the belt.

2

Removing Slack From Belt

40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

6. To release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully.

WARNING!

A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.).

Adjustable Upper Shoulder Belt Anchorage

In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that serves you best.

Adjusting Upper Shoulder Belt

As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you'll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.

Automatic Locking Mode Ð If Equipped

In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt.

When To Use The Automatic Locking Mode

Anytime a child safety seat is installed in the rear center seating position. Children 12 years old and under should be properly restrained in the rear seat whenever possible.

How To Use The Automatic Locking Mode

1.Buckle the combination lap and shoulder belt.

2.Grasp the shoulder portion and pull downward until the entire belt is extracted.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41

3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.

2

How to Disengage The Automatic Locking Mode

Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

Energy Management Feature

This vehicle has a safety belt system with an energy management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision.

This safety belt system has a retractor assembly that is designed to release webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant's chest.

42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

²The belt and retractor assembly must be replaced if the seat belt assembly ªautomatic locking retractorº feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual.

²Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.

Seat Belt Pretensioners

The driver and front passenger seat belts are equipped with a pretensioning device that is designed to remove any slack from the seat belt systems in the event of a collision. This device improves the performance of the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.

NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly.

The pretensioners are triggered by the Occupant Restraint Control (ORC) Module. Like the front airbags, the pretensioners are a single use item. After a collision that is severe enough to deploy the airbags and pretensioners, they must be replaced.

Enhanced Seat Belt Use Reminder System (BeltAlert)

If the driver's seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, the Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96

seconds or until the driver's seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the driver's seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).

The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by following these steps:

NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. The manufacturer does not recommend deactivating the Enhanced Warning System (BeltAlert).

1. Turn the ignition switch to the OFF position, and buckle the driver's seat belt.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43

2.Turn the ignition key to the ACCESSORY/RUN position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off.

3.Within 60 seconds of starting the vehicle, unbuckle 2 and then re-buckle the driver's seat belt at least three times with 10 seconds, ending with the seat belt buckled.

4.Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming.

The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.

NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver's seat belt remains unfastened.

44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Seat Belts and Pregnant Women

We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.

Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.

Seat Belt Extender

If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender and store it.

WARNING!

Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

Driver And Front Passenger Supplemental

 

This vehicle has airbags for both the driver and right

Restraint Systems (SRS)

front passenger as a supplement to the seat belt restraint

 

systems. The driver's front airbag is mounted in the

 

 

2

 

steering wheel. The passenger side airbag is mounted in

 

the instrument panel, above the glove compartment. The

 

 

words SRS/AIRBAG are embossed on the airbag covers.

 

NOTE: The front airbags are certified to the Federal

 

regulations that allow less forceful deployment.

 

The front airbags have a multistage inflator design. This

 

may allow the airbag to have different rates of inflation

 

that are based on collision severity and occupant size.

1 Ð Driver Airbag

 

 

 

2 Ð Passenger Airbag

 

 

 

3 Ð Knee Bolster

 

 

 

46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

This vehicle is equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. They are located above the side windows. Their covers are also labeled SRS/AIRBAG.

Window Airbag Location

NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.

WARNING!

²Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.

²Do not stack luggage or other cargo up high enough to block the location of the window bag. The area where the window bag is located should remain free from any obstructions.

²Do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason.

²Do not cover or place items on the airbag covers. These items may cause serious injury during inflation.

NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the window bags.

The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection.

The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.

The window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.

1. Children 12 years and under should always ride 2 buckled up in a rear seat.

Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger airbag. An airbag deployment could cause severe injury or death to infants in that position.

Children that are not big enough to properly wear the vehicle seat belt should be secured in the rear seat, in a child restraint or belt-positioning booster seat. Older children who do not use child restraints or beltpositioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.

If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the

48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

seat as far back as possible, and use the proper child restraint. See ªChild Restraintº in this section.

You should read the instructions provided with your child restraint to make sure that you are using it properly.

2.All occupants should use their lap and shoulder belts properly.

3.The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate.

4.Do not lean against the door or window, airbags will inflate forcefully into the space between you and the door.

5.If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ªIf You Need Assistanceº in Section 9 of this manual.

WARNING!

²Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won't deploy at all. Always wear your seat belts even though you have airbags.

²Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.

²The left and right side curtain airbags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.

Airbag System Components

The airbag system consists of the following:

²Occupant Restraint Control Module

²Airbag Warning Light

²Driver Airbag

²Passenger Airbag

²Side Curtain Airbags above Side Windows

²Side Remote Acceleration Sensors

²Steering Wheel and Column

²Instrument Panel

²Interconnecting Wiring

²Knee Impact Bolsters

²Front Acceleration Sensors

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49

² Driver and Front Passenger Seat Belt Pretensioner

How The Airbag System Works

²The Occupant Restraint Control (ORC) Module de- 2 termines if a frontal, side, or rollover collision is severe enough to require the front and/or side airbags to inflate. The front airbag inflators are designed to provide different rates of airbag inflation from direction provided by the ORC. The ORC will not detect rear impacts.

The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Also, the ORC turns on the ªAirbag Warning Lightº for 6 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the ªAirbag Warning Lightº will

turn off. If the ORC detects a malfunction in any part of the system, it turns on the ªAirbag Warning Lightº either momentarily or continuously. A single chime will sound if the light comes on again after initial start up.

WARNING!

Ignoring the ªAirbag Warning Lightº in your instrument panel could mean you won't have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.

²The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates are possible, based on collision severity and occupant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50±70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger.

The driver front airbag gas is vented through the vent holes in the sides of the airbag. The passenger front airbag gas is vented through the vent holes in the sides of the airbag. In this way, the airbags do not interfere with your control of the vehicle.

+ 354 hidden pages