Jeep Patriot 2007 User Manual

0 (0)
Jeep Patriot 2007 User Manual

PATRIOT 2007

2007 OWNER’ S MANUAL

SECTION

TABLE OF CONTENTS

PAGE

1

2

3

4

5

6

7

8

9

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INTRODUCTION

. . 3

1

 

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 9

2

 

 

 

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. 73

3

 

 

 

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

163

4

 

 

 

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

233

5

 

 

 

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

323

6

 

 

 

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

339

7

 

 

 

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

391

8

 

 

 

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

411

9

 

 

 

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

421

10

 

INTRODUCTION

 

 

 

 

 

 

1

 

 

 

 

 

CONTENTS

 

 

 

 

 

m Introduction . . . . . . . . . . . . . . . . . .

. . . . . . . . . 4

m Warnings And Cautions . . . . . . . . . . . . . . . . . . .

7

 

N Roll Over Warning . . . . . . . . . . . .

. . . . . . . . . 4

m Vehicle Identification Number . . . . . . . . . . . . . . .

7

 

m How To Use This Manual . . . . . . . . .

. . . . . . . . . 5

m Vehicle Modifications/Alterations . . . . . . . . . . . .

8

 

4 INTRODUCTION

INTRODUCTION

This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings.

When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained technicians and genuine Mopart parts, and is interested in your satisfaction.

Roll Over Warning

Utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can be caused to go out of control. Because of the higher center of gravity and the narrower track, if this vehicle is out of control it may roll over when some other vehicles may not.

Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle, and severe or fatal injury. Drive carefully.

Roll Over Warning Label

Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat

INTRODUCTION 5

belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 1 million annually. In a roll over crash an unbelted person

is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section contains the information you desire.

The detailed index, at the rear of this manual, contains a complete listing of all subjects.

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this owner's manual:

6 INTRODUCTION

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

Vehicle Identification Number (VIN) is found on the driver's front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle registration or title.

INTRODUCTION 7

1

Vehicle Identification Number

8 INTRODUCTION

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2

CONTENTS

m A Word About Your Keys . . . . . . . . . . . . . . . . . .

12

N Ignition Key Removal . . . . . . . . . . . . . . . . . . .

12

N Locking Doors With The Key . . . . . . . . . . . . . .

13

N Key-In-Ignition Reminder . . . . . . . . . . . . . . . .

14

m Sentry Key Ð If Equipped . . . . . . . . . . . . . . . . .

14

N Replacement Keys . . . . . . . . . . . . . . . . . . . . . .

15

N Sentry Key Programming . . . . . . . . . . . . . . . . .

16

N General Information . . . . . . . . . . . . . . . . . . . .

16

m Steering Wheel Lock Ð Manual Transmission

 

Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

N If You Wish To Manually Lock The Steering

 

Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

N To Release The Steering Wheel Lock . . . . . . . . .

17

N Automatic Transaxle Ignition Interlock System . .

17

m Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18

N Manual Door Locks . . . . . . . . . . . . . . . . . . . . .

18

N Power Door Locks . . . . . . . . . . . . . . . . . . . . .

19

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

N ªChild-Protectionº Door Lock System (Rear Doors)

Ð If Equipped . . . . . . . . . . . . . . . . . . . . . . . .

23

m Remote Keyless Entry Ð If Equipped . . . . . . . . .

24

N To Unlock The Doors And Liftgate . . . . . . . . . .

25

N To Lock The Doors And Liftgate . . . . . . . . . . . .

26

N Using The Panic Alarm: . . . . . . . . . . . . . . . . . .

26

N To Turn Off ªFlash Lights With Lockº . . . . . . . .

27

N Programming Additional Transmitters . . . . . . . .

27

N General Information . . . . . . . . . . . . . . . . . . . .

29

N Battery Replacement . . . . . . . . . . . . . . . . . . . .

29

m Security Alarm System Ð If Equipped . . . . . . . . .

30

N To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .

31

N To Disarm The System . . . . . . . . . . . . . . . . . . .

31

N Security System Manual Override . . . . . . . . . . .

32

m Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

m Power Windows . . . . . . . . . . . . . . . . . . . . . . . .

34

N Power Window Switches . . . . . . . . . . . . . . . . .

34

N Auto Down . . . . . . . . . . . . . . . . . . . . . . . . . .

35

N Window Lockout Switch . . . . . . . . . . . . . . . . .

36

m Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .

36

N Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .

37

N Adjustable Upper Shoulder Belt Anchorage . . . .

42

N Second Row Center Lap/Shoulder Belt Operating

Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .

43

N Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .

46

N Enhanced Driver Seat Belt Reminder System

 

(BeltAlert) . . . . . . . . . . . . . . . . . . . . . . . . . . .

47

N Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .48

N Seat Belts And Pregnant Women . . . . . . . . . . . .49

N Driver And Front Passenger Supplemental

Restraint System (SRS) - Airbag . . . . . . . . . . . .49

N Event Data Recorder (EDR) . . . . . . . . . . . . . . .58

N Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .60

m Engine Break-In Recommendations . . . . . . . . . . .69

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

11

m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .

69

N Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .

69

N Safety Checks You Should Make Inside The

2

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

70

N Periodic Safety Checks You Should Make Outside

The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .

71

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.

Ignition Key Removal

Automatic Transaxle

Place the shift lever in PARK. Turn the ignition switch to the ACC position, push the key and cylinder inward, rotate the key to the LOCK position, and remove the key.

Ignition Key Positions

Vehicle Key

NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.

WARNING!

Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don't leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

CAUTION!

An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors 2 when leaving the vehicle unattended.

Manual TransaxleÐIf Equipped

Turn the ignition switch to the ACC position, push the key and cylinder inward, rotate the key to the LOCK position, and remove the key.

Locking Doors With The Key

You can insert the key with either side up. To lock the door, turn the key rearward, to unlock the door, turn the key forward. See Section 7 of this manual for door lock lubrication.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Key-In-Ignition Reminder

Opening the driver's door when the key is in the ignition, sounds a signal to remind you to remove the key.

NOTE: With the driver's door open, and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function.

SENTRY KEY Ð IF EQUIPPED

The Sentry Key Immobilizer System prevents unauthorized operation of the vehicle by disabling the engine. The system will shut the engine off after two (2) seconds of running if an invalid key is used to start the vehicle. This system utilizes ignition keys, which have an electronic chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle.

The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or

unlocked. During normal operation, the Theft Alarm/ Immobilizer Light will come on for three (3) seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a problem with the electronics.

If the bulb begins to flash after the bulb check, this indicates that an invalid key has been used to start the vehicle. Both of these conditions will result in the engine being shut off after two (2) seconds of running.

Keep in mind that a key, which has not been programmed is also considered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle.

If the Theft Alarm/Immobilizer Light comes on during normal vehicle operation, (the vehicle has been running for longer than 10 seconds), a fault has been detected in the electronics and the vehicle should be serviced as soon as possible.

NOTE:

²The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

²Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system.

All of the keys provided with your new vehicle have been programmed to the vehicle electronics.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

Replacement Keys

NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once 2 a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle.

At the time of purchase, the original owner is provided with a four-digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one, which has never been programmed.

NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Sentry Key Programming

You can program new keys to the system if you have two valid sentry keys by performing the following procedure:

1.Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code.

2.Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key.

3.Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds, a chime will sound and the Theft Alarm Light will begin to flash. Turn the ignition switch OFF and remove the second key.

4.Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off.

The new Sentry Key has been programmed.

Repeat this procedure to program up to 8 keys. If you do not have a programmed sentry key, contact your dealer for details.

General Information

The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:

²This device may not cause harmful interference.

²This device must accept any interference that may be received, including interference that may cause undesired operation.

STEERING WHEEL LOCK Ð Manual Transmission Only

Your manual transmission vehicle is equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.

If You Wish To Manually Lock The Steering Wheel:

With the engine running, turn the steering wheel upside down, turn off the engine and remove the key. Turn the steering wheel slightly in either direction until the lock engages.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

To Release The Steering Wheel Lock:

 

Insert the key in the ignition switch and start the engine.

 

If the key is difficult to turn, move the wheel slightly to

2

the right or left to disengage the lock.

NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it.

Automatic Transaxle Ignition Interlock System

This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ACC, or ON positions, and the brake pedal is depressed.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

DOOR LOCKS

Manual Door Locks

Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.

WARNING!

For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.

WARNING!

When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.

Manual Door Lock Plunger

CAUTION!

An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended.

Power Door Locks

A door lock switch is located on the driver door panel. Press this switch to lock or unlock the doors.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

2

Power Door Lock Switch Location

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Power Door Lock Switches

Automatic Door LocksÐIf Equipped

The doors will lock automatically on vehicles with power door locks if all of the following conditions are met:

1.The Auto Lock feature is enabled.

2.The transmission is in gear.

3.All doors are closed.

4.The throttle is pressed.

5.The vehicle speed is above 15 mph (24 km/h).

6.The doors were not previously locked using the power door lock switch or remote keyless entry transmitter.

The Automatic Door Lock feature can be enabled or disabled. Refer to ªPersonal Settingsº (Customer Programmable Features) in the Electronic Vehicle Information Center (EVIC) Ð if equipped section of this manual for details.

For vehicles not equipped with the EVIC the Automatic Door Locks can be enabled or disabled by performing the following procedure:

1.Close all doors and place the key in the ignition.

2.Cycle the ignition switch between LOCK and ON and back to LOCK 4 times ending up in the LOCK position.

Ignition Key Position

3.Depress the power door lock switch to lock the doors.

4.Verify reprogramming by driving the vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

Auto Unlock

The doors will unlock automatically on vehicles with power door locks if:

1. The Auto Unlock feature is enabled.

2

 

2.The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h).

3.The transmission is in NEUTRAL or PARK.

4.The driver door is opened.

5.The doors were not previously unlocked.

6.The vehicle speed is 0 mph (0 km/h).

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The Auto Unlock feature can be enabled or disabled. Refer to ªPersonal Settingsº (Customer Programmable Features) in the Electronic Vehicle Information Center (EVIC) Ð if equipped section of this manual.

For vehicles not equipped with the EVIC the Auto Unlock Feature can be enabled or disabled by performing the following procedure:

1.Close all doors and place the key in the ignition.

2.Cycle the ignition switch between LOCK and ON and back to LOCK 4 times ending up in the LOCK position.

Ignition Key Position

3. Depress the power door unlock switch to unlock the doors.

4. A single chime will indicate the completion of the programming.

NOTE: Use the Auto Door Locks and Auto Unlock features in accordance with local laws.

ªChild-Protectionº Door Lock System (Rear Doors) Ð If Equipped

Insert the tip of the ignition key into the lock and rotate to the lock or unlock position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

2

Inserting Ignition Key

Child Protection Door Lock Location

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.

NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.

REMOTE KEYLESS ENTRY Ð IF EQUIPPED

Three Button Transmitter

This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a maximum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.

NOTE: The line of transmission must not be blocked with metal objects.

To unlock the doors and liftgate:

Press and release the UNLOCK button on the key fob once to unlock only the driver's door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). Refer to ªTurn Headlamps on with Remote Key Unlockº under ªPersonal Settingsº in the Electronic Vehicle Information Center (EVIC) section of this manual for details.

NOTE: The system can also be programmed to unlock all doors on the first press of the UNLOCK button. On electronic vehicle information center (EVIC) equipped vehicles refer to ªRemote Unlock Driver's Door 1stº

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

under ªPersonal Settingsº in the EVIC section of this manual. On non EVIC ± equipped vehicles perform the following steps:

The system can be programmed to unlock all the doors 2 upon the first UNLOCK button press by using the following procedure:

1.Press and hold the LOCK button on a programmed key fob.

2.Continue to hold the LOCK button at least 4 seconds, but not longer than 10 seconds, then press and hold the UNLOCK button. A single chime will sound to indicate that this feature has changed.

3.Release both buttons at the same time.

4.Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the keyfob.

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.

5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.

To lock the doors and liftgate:

Press and release the LOCK button on the transmitter to lock all doors. The turn signal lights will flash and the horn will chip once to acknowledge the lock signal. If desired, the ªSound Horn On Lockº feature can be turned on or off. On electronic vehicle information center (EVIC) equipped vehicles refer to ªPersonal Settingsº in the ªElectronic Vehicle Information Center (EVIC)º section of this manual. On non EVIC ± equipped vehicles perform the following steps:

1. Press the LOCK button for 4 to 10 seconds.

2. While the LOCK button is pressed (after 4 seconds), press the PANIC button. Release both buttons.

The ªSound Horn On Lockº and ªFlash Lamps With Lockº feature can be reactivated by repeating this procedure.

Using The Panic Alarm:

To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.

The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater.

NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system.

To Turn Off ªFlash Lights With Lockº

NOTE: The Flash Lights With Lock feature can be turned on or off. On electronic vehicle information center (EVIC) equipped vehicles refer to 9Personal Settings9 in the EVIC section of this manual. On non EVIC - equipped vehicles perform the following steps:

1.Press the UNLOCK button for 4 to 10 seconds.

2.While the UNLOCK button is pressed, (after 4 seconds) press the LOCK button. Release both buttons.

3.Test the flash lamps with LOCK feature while outside of the vehicle, by pressing the LOCK button on the key fob with the ignition in the LOCK position, and the key removed.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to 2 deactivate the Security Alarm.

The ªFlash Lights On Lock/Unlockº feature can be reactivated by repeating this procedure.

Programming Additional Transmitters

Vehicles will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of eight fobs can be programmed for your vehicle. Additional fobs can be programmed to your vehicle through the use of a currently programmed fob.

NOTE: When entering program mode using that fob, all other programmed fobs will be erased and you will have to reprogram them for your vehicle.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Use the Following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key:

1.Enter your vehicle and close all doors.

2.Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this programming procedure).

3.Place the key into the ignition.

4.Turn the ignition to the ON position ( Do not start the engine ).

5.Press and hold the UNLOCK button on the key fob.

6.After holding the UNLOCK button for four seconds, also press the PANIC button within 6 seconds.

7.When a single chime is heard release both buttons. The chime is an indication that you have successfully entered

program mode. All fobs that are to be programmed must be done so within 60 seconds of when the chime was heard.

8.Using the fob to be programmed, press and release both the LOCK and UNLOCK buttons, simultaneously.

9.A single chime will be heard.

10.Within four seconds of hearing the chime, press and release the UNLOCK button on the fob.

11.A single chime will be heard.

12.Repeat steps 8 through 10 to program up to six additional fobs.

13.Turn the ignition to the OFF position.

14.Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After

60seconds, all programmed fobs function normally.

NOTE: If you do not have a programmed transmitter, contact your dealer for details.

General Information

This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference that may be received including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29

If your Remote Lock Control fails to operate from a normal distance, check for these two conditions.

1.Weak batteries in transmitter. The expected life of 2 batteries is five years.

2.Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios.

Battery Replacement

The recommended replacement battery is CR2032.

NOTE: Perchlorate Material ± special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.º

Loading...
+ 410 hidden pages