Jaguar Jaguar XE (2015) Owner’s Manual

Download

OWNER'S HANDBOOK

Publication Part No. JJM 10 02 36 161

www.JagDocs.com

Introduction

ABOUT THIS HANDBOOK

Please take the time to study all of the owner/operator literature supplied with your vehicle as soon as possible.

IMPORTANT

The information contained in this handbook covers all vehicle derivatives and optional equipment, some of which will not be fitted to your vehicle. Due to printing cycles, this handbook may include descriptions of options before they become generally available.

The vehicle options, hardware and software, are designed for the market in which the vehicle is intended for original sale. If your vehicle is to be used in another geographical area, the vehicle may have to be modified to suit local conditions. Jaguar Land Rover Limited is not responsible for the cost of any modifications. Warranty conditions may be affected.

The information contained in this publication was correct when it went to print. Subsequent vehicle design changes may result in a supplement being added to the literature pack. Updates can also be viewed on the Jaguar internet site at: http://www.ownerinfo.jaguar.com.

In the interest of development, the right is reserved to change specifications, design, or equipment at any time without notice and without incurring any obligations. This publication, or part thereof, may not be reproduced nor translated without our approval. Errors and omissions excepted.

SYMBOLS USED IN THIS HANDBOOK

Safety warnings indicate either a procedure which must be followed precisely, or information that should be considered with great care, in order to avoid the possibility of personal injury.

Cautions indicate either a procedure which must be followed precisely, or information that should be considered with great care, in order to avoid the possibility of damage to the vehicle.

This recycling symbol identifies those items that must be disposed of safely in order to prevent unnecessary damage to the environment.

This symbol indicates items that must be disposed of correctly, as they contain harmful substances. Seek advice on disposal from a Dealer/Authorised Repairer and/or the local authority.

This symbol identifies those features that can be adjusted, disabled or enabled by a Dealer/Authorised Repairer.

©Jaguar Land Rover Limited 2015.

Introduction

INSTRUCTIONAL VIDEOS

Throughout this handbook are a selection of QR codes which, when scanned using a smartphone app, will connect the smartphone to relevant instructional videos.

Note: These videos are best viewed using a high-speed internet or 4G connection.

Get the free mobile app at:

Contents

Introduction......................................2

Entering the vehicle..........................6

Exiting the vehicle...........................13

Front seats......................................18

Rear seats.......................................22

Head restraints...............................24

Steering wheel................................27

Seat belts........................................29

Child safety.....................................33

Airbags...........................................40

Instrument panel.............................46

Warning lamps...............................51

Exterior lights.................................56

Interior lights..................................60

Wipers and washers.......................62

Mirrors............................................65

Blind spot monitoring.....................67

Garage door opener........................71

Windows.........................................73

Touch screen..................................76

Heating and ventilation...................79

Storage compartments...................85

Luggage compartment....................87

Towing............................................88

Starting the engine........................100

Intelligent stop/start......................102

Gearbox........................................104

Stability control.............................108

Suspension...................................110

Brakes...........................................111

Parking aids..................................115

Park assist....................................120

Cameras........................................124

Automatic speed limiter (ASL)......126

Cruise control...............................127

Adaptive cruise control.................128

Driving modes..............................135

Progress control system...............137

Driving aids...................................140

Media............................................143

Voice control.................................153

Bluetooth®...................................155

Telephone.....................................157

InControl.......................................159

Navigation system........................164

Fuel and refuelling........................174

Maintenance.................................183

Vehicle cleaning............................200

Fluid level checks..........................203

Vehicle battery..............................210

Fuses............................................214

Tyres.............................................222

Tyre pressure monitoring system

(TPMS).........................................229

Tyre repair kit................................231

Wheel changing............................235

Vehicle recovery...........................240

After a collision.............................243

Vehicle labels................................245

Technical specifications................247

Type approval...............................257

Index.............................................270

Controls overview.........................288

Entering the vehicle

UNLOCKING THE VEHICLE

Any person fitted with an implanted medical device, should make sure that the device is kept at a distance of at least 22 cm (8.7 inches) away from any transmitter mounted in the vehicle. This is to avoid any possibility of interference between the system and the device. Interference may cause the implanted medical device to malfunction, causing serious injury or death. See 255, SMART KEY TRANSMITTER LOCATIONS.

To prevent accidental operation, never leave the Smart key in the vehicle if children or animals are also left in the vehicle.

Note: The operational range of the Smart key will vary considerably, depending on atmospheric conditions and interference from other transmitting devices.

Entering the vehicle

Note: If any of the doors, or the luggage compartment, is unlocked 10 times within a short period of time, the latch will be disabled for approximately one minute.

The vehicle is supplied with 2 Smart keys. The Smart key acts as a remote control for the vehicle's locking/unlocking systems and the alarm system. It will also allow the vehicle to be started without the use of a conventional key. See 8, KEYLESS ENTRY, 14, KEYLESS LOCKING and 100, STARTING THE ENGINE. Each Smart key also has an emergency key housed in a slide-out compartment.

Lock:

• Press to secure the vehicle. The vehicle can be Single or Double locked. See

13, SINGLE LOCKING. See 13, DOUBLE LOCKING.

Exiting the vehicle

DOOR LOCKS AND RELEASE LEVERS

Press the lock button to lock the vehicle.

Press the unlock button to unlock the vehicle.

Pull the door lever to unlock/release the door. Operating the door lever on either front door will unlock all of the doors.

Note: If the car was locked using the Smart key, then operating the door lever will only unlock/release that door and the alarm will sound.

Note: If the vehicle has been Double locked, then the interior door levers will not operate. The vehicle must be unlocked using the Smart key.

SINGLE LOCKING

Briefly press the external door handle's keyless locking sensor, or the Smart key's lock button, to Single lock the vehicle and activate the Perimeter alarm. See 15, PERIMETER ALARM. The hazard warning lamps will flash once to confirm.

Note: Do not place your fingers around the back of the door handle while touching the keyless locking sensor. Doing so will prevent the vehicle from locking, as the keyless unlock sensor is located on the inner surface of the handle.

Single locking secures the vehicle and prevents the doors and the luggage compartment being opened from outside of the vehicle. The doors can be unlocked and opened from inside the vehicle.

Note: Always secure the vehicle when left unattended. Where possible, always secure the vehicle to the maximum available level of security.

DOUBLE LOCKING

Never Double lock the vehicle with people, children, or pets inside. In the event of an emergency, they would be unable to escape and the emergency services would be unable to release them quickly.

Press the external door handle keyless locking sensor, or the Smart key lock button, twice within 3 seconds to Double lock the vehicle and activate the Full alarm system. See 15, FULL ALARM. The hazard warning lamps will flash twice to confirm and (if enabled) an audible lock warning will sound.

Note: Do not place your fingers around the back of the door handle while touching the keyless locking sensor. Doing so will prevent the vehicle from locking.

Note: The Audible Lock Warning can be enabled/disabled via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

Double locking secures the vehicle and prevents the doors and the luggage compartment being unlocked or opened from inside or outside of the vehicle. The vehicle can only be unlocked with the correct Smart key.

Exiting the vehicle

When the vehicle is Double locked, an open window or an open sunroof will (if enabled) cause the alarm sensors to activate the alarm system, due to the movement of air currents. Make sure that all of the windows and the sunroof are fully closed before Double locking the vehicle.

Note: The Alarm Sensors can be enabled/disabled via the Vehicle Set-up menu.

LOCK CONFIRMATION

If you are uncertain whether the vehicle is locked and armed (either by Single or Double locking), press the Smart key lock button and the hazard warning lamps will flash to indicate the current status; once for Single lock and twice for Double lock.

Note: If the vehicle is not already locked and armed, pressing the Smart key lock button will Single lock the vehicle, press the lock button again within 3 seconds to Double lock.

MISLOCK

When trying to lock the vehicle with the Smart key, an audible mislock warning will sound twice if:

• Any of the doors, luggage compartment or bonnet are open or not securely latched.

• A malfunction of a lock or latch is detected.

• The ignition is on.

If a mislock occurs, then check the vehicle and if the problem persists consult a Dealer/Authorised Repairer.

Note: Operating the interior or exterior door handles, while attempting to unlock, lock, or change the child lock status of the vehicle (including Drive-away locking), may cause the security system to ignore any unlock, lock, or child lock requests.

GLOBAL CLOSING

Make sure that no children, pets, or obstructions are in any open aperture before operating Global closing.

Make sure that all of the doors are closed and securely latched, then press and hold the lock button on the Smart key for 3 seconds. Alternatively, press and hold the external door handle keyless locking sensor for 3 seconds. The vehicle will Single lock and the alarm system will be fully armed immediately. After 3 seconds, all of the windows and the sunroof will close.

Note: Do not place your fingers around the back of the door handle while touching the keyless locking sensor. Doing so will prevent the vehicle from locking.

Note: If the Smart key's lock button, or the external door handle's keyless locking sensor, is released before the windows and the sunroof have fully closed, then the windows and the sunroof will stop closing.

Note: Windows Global Close can be enabled/disabled via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

KEYLESS LOCKING

Remove all the valid Smart keys and emergency key blades from the vehicle when it is left unattended. This will help to prevent the alarm from being disarmed, and therefore, help to prevent theft.

Note: The vehicle will not lock automatically.

Exiting the vehicle

The Full alarm system is the maximum level of security for the vehicle. It consists of:

• The Perimeter alarm.

• A Battery-backed sounder.

• A Tilt sensor.

• An Intrusion sensor.

To Single lock the vehicle, touch only the keyless locking sensor (1) once, without grabbing the door handle. The hazard warning lamps will flash once, as confirmation (in some markets, an audible warning will sound).

To Double lock the vehicle, touch only the keyless locking sensor (1) twice within 3 seconds. The hazard warning lamps will flash twice (with a long second flash), and (if enabled) an audible lock warning will sound.

Note: Do not place your fingers around the back of the door handle while touching the keyless locking sensor. Doing so will prevent the vehicle from locking, as the keyless unlocking sensor is located on the inner surface of the door handle.

Note: The Audible Lock Warning can be enabled/disabled via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

Note: Keyless locking will only activate if all of the doors, the bonnet, and the luggage compartment are closed securely and the Smart key is outside of the vehicle.

FULL ALARM

No modifications or additions should be made to the alarm system. Such changes could cause this system to malfunction.

Double lock the vehicle to activate the Full alarm system. See 13, DOUBLE LOCKING and 14,

KEYLESS LOCKING.

PERIMETER ALARM

Single lock the vehicle to activate the Perimeter alarm system. See 13, SINGLE LOCKING and 14, KEYLESS LOCKING.

The Perimeter alarm system is the minimum level of security for the vehicle.

BATTERY-BACKED SOUNDER

In certain markets, a separate Battery-backed sounder is fitted. This device will sound the alarm if the vehicle's battery or the alarm sounder is disconnected when the security system is armed.

DEACTIVATING THE ALARM WHEN TRIGGERED

If the alarm has been triggered, it can be deactivated by any one of the following methods:

• Pressing the unlock button on the Smart key.

• Opening a door using Keyless entry.

• Pressing the START/STOP button with a valid Smart key present.

The cause of the last alarm activation can be displayed in the Message centre via the Vehicle

Info and Last Alarm menus. See 47, INSTRUMENT PANEL MENU.

Exiting the vehicle

TILT SENSOR

The Tilt sensor detects any change in the vehicle's angle to the ground. When the alarm is armed and the vehicle is Double locked, a significant change in the vehicle's angle will activate the alarm.

Note: The Tilt sensor is an alarm sensor. The Alarm Sensors can be enabled/disabled (for

one alarm cycle only) via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

INTRUSION SENSOR

The Intrusion sensor detects an intrusion into the cabin area. When the alarm is armed and the vehicle is Double locked, an intrusion into the cabin through the windows will activate the alarm.

Note: The Intrusion sensor is an alarm sensor. The Alarm Sensors can be enabled/disabled (for one alarm cycle only) via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

PASSIVE ARMING

In some markets, the vehicle is fitted with a Passive arming feature which can, if enabled, automatically arm the anti-theft system. Passive arming will automatically arm the Perimeter alarm system 60 seconds after the driver's door is closed, provided that all of the other doors, the bonnet and the luggage compartment are also closed. The ignition must also be switched off with no valid Smart keys inside the vehicle.

Passive arming will not lock the vehicle, although access to the luggage compartment via the interior or exterior release buttons will be prevented and the fuel filler flap will be locked.

Passive arming can be enabled/disabled by a Dealer/Authorised Repairer.

AUTOMATIC RELOCKING AND REARMING OF THE ALARM

Automatic relocking and re-arming is a feature which, if enabled, automatically relocks the vehicle and arms the anti-theft system.

If the vehicle is in a locked and armed state and the Smart key unlock button is pressed, but none of the doors or the luggage compartment are opened within 40 seconds, then the vehicle automatically relocks all of the doors and the luggage compartment, and re-arms the alarm system. This will also occur if the Smart key is detected and a door handle is grabbed to operate the keyless unlock sensor. See 8, KEYLESS ENTRY.

Note: Automatic relocking and re-arming will only relock to a Single locked state. If the vehicle was previously Double locked, then the alarm sensors will also re-arm.

Automatic relocking and re-arming can be enabled/disabled by a Dealer/Authorised Repairer.

SENSOR FAULTS

If the security systems detect a fault with one of the security sensors, 2 error tones will sound from the alarm after the vehicle is unlocked and disarmed. If this condition occurs, then consult a Dealer/Authorised Repairer for rectification.

EMERGENCY LOCKING

In the event of the battery discharging, or a fault with the Keyless locking system, each of the doors must be locked manually.

The emergency key blade is required for this procedure. See 6, UNLOCKING THE VEHICLE.

Note: Do not leave the emergency key blade in the vehicle at any point during the emergency locking procedure.

Open a door and locate the emergency lock access cover. Using the emergency key blade, rotate the cover counter-clockwise to release and then pull to remove it from the door.

Insert the emergency key blade firmly into the emergency lock. The emergency key blade can now be removed.

Refit the emergency lock access cover and rotate it clockwise to secure it firmly.

Close the door and check that it is locked. Repeat the procedure for all other unlocked doors.

Exiting the vehicle

Front seats

ELECTRIC SEATS

Do not adjust the seat while the vehicle is moving. Doing so could cause loss of vehicle control and personal injury.

Cushion length adjustment.

Bolster adjustment (inflate/deflate).

Lumbar support adjustment.

• Press the top of the button to raise.

• Press the bottom of the button to lower.

• Press the middle front of the button to inflate.

• Press the middle rear of the button to deflate.

Seatback angle adjustment.

Height adjustment.

Forward and rearward adjustment.

Cushion front tilt adjustment.

To adjust the seats, the Smart key must be in the vehicle and the ignition switched on.

If an obstruction is encountered while the seat is in motion, the seat will stop moving and further movement will be restricted until reset.

To reset the seat:

Remove the obstruction.

Adjust the seat to the point where the movement was restricted.

Press and hold the switch for at least 2 seconds to override the restriction.

Front seats

MANUAL SEATS

Do not adjust the seat while the vehicle is moving. Doing so could cause loss of vehicle control and personal injury.

Forward and rearward adjustment.

Seat height adjustment.

Seatback angle adjustment.

DRIVING POSITION MEMORY

Memory set button.

Memory presets.

Front seats

After adjustment of the driver's seat, steering column and the exterior mirrors, the vehicle can memorise these settings using the driver's door memory buttons. See 27, ADJUSTING THE

STEERING WHEEL and 65, EXTERIOR MIRRORS.

Press the memory set button (M) to activate the memory function. The LED indicator lamp will illuminate to confirm.

Press one of the preset buttons within 5 seconds to memorise the current settings. MEMORY 1 (2 or 3) SETTINGS SAVED will be displayed in the Message centre, accompanied by an audible chime to confirm the settings have been memorised.

A seat position can only be memorised during the 5 second period.

Any existing settings, for a previous memory preset, will be over-written when programming a new memory position.

RECALLING A MEMORISED POSITION

Press the appropriate memory preset button. MEMORY 1 (2 or 3) SETTINGS RECALLED will be displayed in the Message centre.

SITTING IN THE CORRECT POSITION

The driver and front seat passenger must not ride with the seat fully reclined.

Do not adjust the seat while the vehicle is moving.

The seat, head restraint, seat belt, and airbags, all contribute to the protection of the user. Correct use of these components will give you greater protection, therefore, you should always observe the following points:

Sit in an upright position, with the base of your spine as far back as possible. To achieve optimum benefit of the seat belt in the event of an accident, do not recline the seat excessively.

Do not move the driver's seat too close to the steering wheel. Ideally, a minimum distance of 254 mm (10 inches) is recommended between the breastbone and the steering wheel airbag cover. Hold the steering wheel in the correct position, with your arms slightly bent.

Adjust the head restraint so that the top of the head restraint is the same height as the top of the head.

Position the seat belt so that it is midway between your neck and your shoulder. Fit the strap tightly across your hips, not across your stomach.

Make sure that your driving position is comfortable and enables you to maintain full control of the vehicle.

Rear seats

REAR SEAT SAFETY

Never allow passengers to travel in the Luggage compartment under any circumstances.

All vehicle occupants should be seated correctly and must wear a seat belt at all times when the vehicle is in motion.

FOLDING AND RAISING THE REAR SEATS

All items carried in the vehicle should be properly secured. See 87, LUGGAGE ANCHOR POINTS. Unsecured items can cause death or serious injury in the event of an impact or sudden manoeuvre.

When using seat belts to restrain items other than occupants, make sure that the belts are not damaged or exposed to sharp edges.

Always take note of safety warnings and labels attached to the rear seats. The labels give advice on safely folding and raising the seats.

Note: The folding rear seats are not available on all vehicles. It is dependent on the vehicle specification.

Open the luggage compartment.

Pull the relevant seat release cable handle.

Fold the seatback forwards and, if required, repeat the process for the other seat section.

The middle seatback can also be released

separately. Press and hold the button to release and then fold the middle seatback forward.

Before folding a rear seat, make sure that the seat is not occupied and that no person has any part of their body on the seat cushion. The rear seatbacks are spring loaded and could cause personal injury or damage when released.

Make sure that when the seatbacks are raised, the seat belts are routed correctly in front of the seatback and are not trapped by the seatbacks or the locking mechanism. Failure to do this may cause damage to the seat belt, which could also result in a new seat belt being required.

Make sure that when the seatbacks are raised, the locking mechanism is fully engaged.

Rear seats

Before driving, make sure that the head restraints are fitted and correctly adjusted for each seat's occupant. See 24, REAR HEAD RESTRAINTS.

Rear centre seat belt release

The rear centre seat belt can be released from its buckle, before folding the rear seatback/s, to allow for improved access to the Luggage compartment.

Use the seat belt tongue (1), from a rear outboard seat, to press the centre seat buckle's release button. The centre seat belt will then fully retract (2).

Make sure that the rear centre seat belt is correctly refitted to the buckle when the rear seatback/s have been returned to the raised position.

Head restraints

FRONT HEAD RESTRAINTS

Head restraints are designed to support the head, not the back of the neck. The head restraint must be positioned correctly to restrain rearward movement of the head in a collision or sudden stop.

While stationary, adjust the head restraint so that the top of the head restraint is the same height as the top of the seat occupant's head. An incorrectly adjusted head restraint increases the risk of death or serious injury in the event of a collision.

Never adjust the head restraints while the vehicle is in motion.

Do not drive or carry passengers with the head restraint removed from an occupied seat. The absence of a correctly adjusted head restraint increases the risk of neck injury in the event of a collision.

To raise, pull the head restraint upwards. It will click and lock in to position.

Note: Do not try to raise the head restraint further than the third adjustment position.

To lower, press and hold the button on the side of the head restraint, then push down.

To remove the head restraint, raise the head restraint to its uppermost position.

Press and hold the seatback socket, on each side of the head restraint.

With the aid of a second person, lift the head restraint out of the seatback.

Always store a removed head restraint securely.

To refit the head restraint:

Make sure that the head restraint is facing the correct direction.

Insert the stems of the head restraint into the seatback sockets and then push it downwards, until at least the first click.

Adjust the head restraint to suit the seat occupant.

REAR HEAD RESTRAINTS

Head restraints are designed to support the head, not the back of the neck. The head restraint must be positioned correctly to restrain rearward movement of the head in a collision or sudden stop.

Head restraints

Never adjust the head restraints while the vehicle is in motion.

It is possible to swivel the head restraint forwards or backwards. For greater protection in the event of a collision, the head restraint should be adjusted, so that it is as close to the back of the seat occupant's head as is practical.

To raise, pull the head restraint upwards, it will click and lock in to position.

To lower, press and hold the locking collar, then push down on the head restraint.

To adjust the angle of the head restraint, press and hold the button on the side of the restraint, then rotate to the desired position.

To remove the head restraint, raise the head restraint to its uppermost position.

Note: If the head restraint's angle can be adjusted, then rotate to the fully forward position.

Press in the locking collar, while also pressing down and holding the seatback socket.

With the aid of a second person, lift the head restraint out of the seatback.

Always store a removed head restraint securely.

To refit the head restraint:

Make sure that the head restraint is facing the correct direction.

Insert the stems of the head restraint into the seatback sockets and then push it downwards, until at least the first click.

Head restraints

Adjust the head restraint to suit the seat occupant.

Steering wheel

ADJUSTING THE STEERING WHEEL

Never adjust the steering wheel while the vehicle is moving.

Do not use steering wheel mounted security devices on vehicles with electrically operated steering columns. Movement of the steering column in Exit and entry mode, could result in damage to the vehicle or possible injury to the occupant.

Electric steering column

Vehicles with an electric steering column, can be adjusted to alter the tilt and reach of the steering wheel:

• Note: The electrically operated steering

column will continue to move until the control is released or until the steering column reaches either of its minimum or maximum positions.

Move the control forwards or rearwards to adjust the reach of the steering wheel.

• Move the switch up or down to adjust the tilt of the steering wheel.

Up to 3 steering wheel positions can be stored and recalled, along with the seat and exterior mirror positions, by the driving position memory. See 20, DRIVING POSITION

MEMORY.

Manual steering column

Vehicles with a manual steering column, can be adjusted to alter the tilt and reach of the steering wheel:

• To unlock the steering column, rotate the control counter-clockwise until the endstop is reached.

• Manually adjust the steering column to the desired reach/tilt position of the steering wheel.

• To lock the steering column, rotate the control clockwise until the endstop is reached.

Note: An audible click will confirm locking of the steering column.

Steering wheel

ENTRY AND EXIT MODE

With the electric steering column control in the AUTO position, the steering column will move to provide easier entry and exit from the vehicle.

On opening the driver’s door, the system will raise the steering column to the highest position, assisting with exit from the vehicle. When the driver’s door is closed and the ignition switched on, the system will return the steering column to the previous position.

Note: If the steering column is adjusted during entry or exit operation, automatic movement will stop.

To prevent automatic movement of the steering column, turn the control clockwise to the alternative position.

Note: If the steering column switch is moved away from AUTO when the steering column is in the exit position, the steering column will move back to its previous position when the driver’s door is closed and the ignition is switched on.

HEATED STEERING WHEEL

To activate the heated steering wheel, press the switch. Press again to switch off.

USING THE SEAT BELTS

Seat belts

Putting on a seat belt: Draw the belt out

smoothly, make sure the seat and your position on the seat, are correct. When correctly positioned, the seat belt should cross the collar bone at the mid-point between the neck and end of your shoulder. Where possible, rear seat passengers should adjust their seating position to achieve the same seat belt position.

Fastening a seat belt: With the seat belt

correctly positioned, place the metal tongue into the buckle nearest to you. Press it in until a click is heard. To release the seat belt, press the red button.

Note: When releasing the seat belt it is advisable to hold the belt before pressing the release button. This will prevent the belt from retracting too quickly.

Seat belt use during pregnancy: Position

the lap strap comfortably across the hips beneath the abdomen. Place the diagonal part of the seat belt between the breasts and to the side of the abdomen.

Position the seat belt correctly for the safety of the mother and unborn child. Never wear just the lap strap, and never sit on the lap strap while using just the shoulder strap. Both of these actions are extremely dangerous, and may increase your risk of serious injury in the event of an accident or during emergency braking.

Never place anything between you and the seat belt in an attempt to cushion the impact in the event of an accident. It can be dangerous, and will reduce the effectiveness of the seat belt in preventing injury.

Do not use comfort clips or devices that would create slack in the seat belt system.

No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack. A slack seat belt offers a greatly reduced level of occupant protection in an impact.

Seat belts

Seat belts are designed to bear upon the bony structure of the body and should be worn low across the front of the pelvis or the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided.

Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed. A slack belt will greatly reduce the protection afforded to the wearer. Make sure that any belt positioning sliders are adjusted so as not to introduce slack.

Belts should not be worn with straps twisted. Each belt assembly must only be used by one occupant; it is dangerous to put a belt around a child being carried on the occupant’s lap.

Riding with a reclined seatback increases your chance of serious or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat belts and air bags) is greatly reduced by reclining your seat. Seat belts must be snug against your hips and chest to work properly. The more the seatback is reclined, the greater the chance that an occupant's neck will strike the shoulder belt. Drivers and passengers should always sit well back in their seats, properly belted and with the seatbacks upright.

The airbag Supplementary Restraint System (SRS) is designed to add to the overall effectiveness of the seat belts. It does not replace them. Seat belts must always be worn.

Seat belts should be worn by all vehicle occupants, for every trip, no matter how short. Failure to do so will greatly increase the risk of death or serious injury in the event of an accident.

Never wear just the lap belt or just the shoulder belt of a lap/shoulder diagonal seat belt. Both of these actions are extremely dangerous and may increase your risk of injury.

SEAT BELT SAFETY

Each seat in the vehicle will have a dedicated seat belt. Each seat belt is designed for an individual seat occupant, aged older than 12 years, or with a body mass greater than 36 kg (80 lb). Occupants with a lower age, or a lower body mass, should use an appropriate child restraint. See 35, CHILD SEAT POSITIONING.

All the seat belts (except for the rear centre seat belt) are equipped with a Load limiter. This will help to regulate the over tension of a seat belt in a severe impact, to help reduce the possibility of injury to the occupant.

A seat belt should be replaced if the webbing becomes frayed, contaminated or damaged.

It is essential to replace the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious.

If any damage, wear, cuts, defects, or impaired operation are noted with the seat belts, the vehicle should be taken to a Dealer/Authorised Repairer for immediate attention. Do not use the vehicle if the seat belts cannot be operated correctly.

Seat belts

Seat belts should be inspected or replaced by qualified personnel only. All replacement parts should be, at least, the same specification as the vehicle's original equipment. If in doubt, consult a Dealer/Authorised Repairer.

Do not attempt to service, repair, replace, modify, or tamper with, any part of the vehicle's seat belts, doing so may render the seat belts as ineffective.

Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. Contaminated seat belts may not operate correctly in an impact and cannot be relied upon.

When using seat belts to restrain items other than occupants, take care to make sure that the belts are not damaged, or exposed to sharp edges.

Do not carry hard, fragile, or sharp items between your person and the seat belt. In an impact, the pressure on such items can cause them to break, which in turn may cause death or serious injury.

SEAT BELT CHECKS

Note: If the vehicle is parked on an incline, the seat belt mechanism may lock. This is a safety feature and the belt should be gently eased out from the upper anchorage.

The seat belts should be inspected regularly to check for fraying, cuts or wear to the webbing, and the condition and security of the mechanism, buckles, adjusters, and mounting points.

• With the seat belt fastened, give the webbing near the buckle a quick upward pull. The buckle must remain securely locked.

• With the seat belt unfastened, unreel the seat belt to the limit of its travel. Check that it unreels smoothly with no snatches or snags. Allow the belt to fully retract, again checking for smooth operation.

• Partially unreel the seat belt, then hold the tongue plate and give a quick forward pull. The mechanism must lock and prevent any further unreeling.

If any of the seat belts fail to meet those criteria, immediately contact a Dealer/Authorised Repairer.

SEAT BELT REMINDER

A front and rear Seat belt reminder system warns the driver when the seat belt of an occupied seat is not fastened or is unfastened during a trip.

Seat belt reminder commences when the vehicle is in motion and the driver's belt is unbuckled. Dependent on market, the warning indicator in the Instrument panel illuminates (see 52, SEAT BELT (RED)), and an audible chime sounds. The visual and audible warnings applicable to the Seat belt reminder feature are market dependent to meet individual market requirements. The warning signals given may also change depending on whether the vehicle is stationary or when the vehicle's speed exceeds a predetermined threshold. In certain markets, the Seat belt reminder feature also applies to the passenger seat.

Seat belts

A graphic in the Message centre also indicates which seat belts are fastened at the start of a journey and also when a seat belt is fastened or unfastened during a journey.

Each seating position is represented by a passenger icon, the colour and symbol of which indicates the seat belt status:

• Tick - seat belt in the indicated position is fastened.

• Cross - seat belt in the indicated position has been unfastened while the vehicle's ignition is on. This indicator will turn grey after 30 seconds.

• Grey - seat belt not fastened.

Note: The indicators will be displayed for 30 seconds each time there is a status change, e.g., a seat belt is unfastened/fastened, or a door is opened and then closed.

In addition, an audible warning will sound if the driver’s, or any occupied passenger's seat belt is not fastened, or is unfastened during a journey.

Note: If a heavy object is placed on a passenger seat, it may activate the Seat belt reminder feature. It is recommended that the object be placed in the luggage compartment or secured using the seat belt.

SEAT BELT PRE-TENSIONERS

The Seat belt pre-tensioners activate in conjunction with the Supplementary Restraint System (SRS) to provide additional protection in the event of a severe frontal impact. They automatically reduce any slack in a seat belt to reduce the forward movement of a seat occupant.

Note: The rear middle seat is not fitted with a seat belt pre-tensioner.

The Seat belt pre-tensioners will activate only once and then must be replaced. Failure to replace them will reduce the effectiveness of the SRS in reducing the risk of serious injury or death in the event of an accident.

After any impact, have the seat belts and pre-tensioners checked and, if necessary, replaced by a Dealer/Authorised Repairer.

Child safety

CHILD SAFETY LOCKS

If children are to be carried in the rear seat positions, it is recommended that the rear door interior handles are disabled.

Press the button on the driver's door, to activate the child door locks and to also inhibit the rear windows. The button's LED indicator lamp will illuminate when active and a confirmation message will also be displayed in the Message centre.

To deactivate, press the button again. The LED lamp will extinguish and a confirmation message will also be displayed in the Message centre.

CHILD SEATS

For optimum safety, children should travel in the rear of the vehicle at all times; front passenger seat travel is not recommended. However, if it is essential that a child travels in the front (not permitted in Australia), set the vehicle seat fully rearward and seat the child in an approved forward-facing child seat. Do not use a rear-facing child seat - an inflating airbag could impact with the seat and cause serious injury.

Do not use a forward-facing child seat until the child using it is above the minimum weight of 9 kg (20 lb.) and able to sit up unaided. Up to the age of two, a child's spine and neck are not sufficiently developed to avoid injury in a frontal impact.

Do not allow a baby or infant to be held or carried on the lap. The force of a crash can increase effective body weight by as much as thirty times, making it impossible to hold onto the child. At all times, children should be restrained in age and size appropriate child seats to reduce the risk of death or serious injury in a crash.

Children typically require the use of a booster seat appropriate to their age and size, thereby enabling the seat belts to be properly fitted, reducing the risk of injury in a crash. Children could be endangered in a crash if their child restraints are not properly secured in the vehicle.

Do not use a child seat that hooks over the seatback. This type of seat cannot be satisfactorily secured and is unlikely to be safe for your child.

The seat belts fitted to your vehicle are designed for adults and larger children. For their safety, it is very important for all infants and children under 12 years of age to be restrained in a suitable child safety seat appropriate to their age and size.

If it is essential that a child travels in the front passenger seat (and national legislation permits this), Jaguar recommends that the following preparations are made before fitting the child restraint.

• Disable the front passenger airbag. See 42, DISABLING THE PASSENGER AIRBAG.

Child safety

• Adjust the front passenger seat fully rearwards.

• Adjust the lumbar support to its minimum support position.

• Adjust the seat cushion to its highest position. If cushion angle adjustment is possible, adjust it to its lowest position.

• Adjust the seatback to an upright position to support the child restraint.

Extreme hazard! Do not use a rearward facing child restraint on a seat protected by an airbag in front of it!

NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur.

This symbol, affixed to the front door B-post on the passenger side, warns against the use of a rear-facing child seat in the front passenger seat, when a front passenger airbag is fitted and operational.

This symbol, affixed to the passenger side sun-visor, warns against the use of a rear-facing child seat in the front passenger seat, when a front passenger airbag is fitted and operational.

CHILD RESTRAINT CHECK LIST

Every time a child travels in the vehicle, observe the following:

• Use appropriate child restraints.

• Carefully follow the instructions provided by the manufacturer of the restraint system.

• Adjust the harnesses for every child on every journey.

• Make sure that all slack is removed from the adult seat belt.

• Always attach the top tether when installing an ISOFIX/i-Size seat (If applicable to seat type).

• Always check the security of the child restraint.

• Do not dress a child in bulky clothing, or place any objects/padding between the child and the restraint.

• Regularly check the fit and condition of child restraints. If the fit is poor, or wear/damage is visible, replace the restraint immediately.

• Set a good example - always wear your seat belt.

• For child seats fitted with a support leg, adjust the leg so that it rests firmly on the floor.

• For some child seats it may be necessary to remove the head restraint to make sure of a stable fit. Always refit a removed head restraint after the child seat is removed.

Child safety

Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses or for attaching other items or equipment to the vehicle.

CHILD SEAT POSITIONING

The information given within the table is correct at the time of going to press. However, availability of child restraints may change. Please consult a Dealer/Authorised Repairer for the latest recommendation.

years

Note: The information contained in the following table may not be applicable to all countries. If you are in any doubt regarding the type and fitment of child seats, seek advice from a Dealer/Authorised Repairer.

Note: The legislation which governs how and where children should be carried when travelling in a vehicle, is subject to change. It is the responsibility of the driver to comply with all regulations in force.

Seating positionsMass group

Rear centreRear outboardFront

passenger*

XUU0 = Up to 10 kg (22 lb.) 0 to 9 months

XUU0+ = Up to 13 kg (29 lb.) 0 to 18 months

XUUI = 9 to 18 kg (20 to 40 lb.) 9 months to 4

XUUII = 15 to 25 kg (33 to 55 lb.) 4 to 9 years

XUUIII = 22 to 36 kg (49 to 80 lb.) 8 to 12 years

• U = Suitable for universal category

restraints approved for use in this mass group.

• UF = Suitable for forward-facing universal

category restraints approved for use in this mass group.

• X = Seat position not suitable for children

in this mass group.

* Always make sure that the front passenger airbag is disabled before using a child restraint in this seating position. See 42, DISABLING THE PASSENGER AIRBAG. The front passenger seat should be positioned fully rearward, the seat cushion to its highest position and the seatback adjusted to an upright position to support the child restraint. If the head restraint has been removed, make sure that it is refitted before the seat is used by a passenger.

Note: Ages given are approximate. In case of doubt, the child’s weight, not age, should be used when considering an appropriate child seat.

Child safety

Crash statistics show that children are safest when properly restrained in a child or infant restraint system that is secured in a rear seating position.

When installing a child seat in the rear, the front seat must be moved forward and upwards to install any rear-facing child seat. Care must be taken not to load any part of the child seat when repositioning the front seat. The space available for front seat occupants will be reduced by the installation of any rearward-facing child seat.

RECOMMENDED CHILD SEATS

Child size/age

Groups 0 and 0+

Group I

Group II and III

Recommended seat ISOFIX Positions

Britax/Römer Baby Safe Plus With Baby-Safe ISOFIX Base

Britax/Römer Duo Plus

Britax/Römer Kid Plus

Recommended seat Non ISOFIX Positions

Britax/Römer Baby Safe Plus

Britax/Römer Duo Plus

Britax/Römer Kid Plus

If the restraint is not correctly anchored, there is a significant risk of injury to the child in the event of a collision or emergency braking.

If removing a head restraint in order to fit a child restraint, always secure the head restraint when storing it. Always refit a removed head restraint after the child restraint is removed.

WARNING: child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses or for attaching other items or equipment to the vehicle.

Both of the outer rear seat positions are equipped to accept ISOFIX and i-Size child restraints.

This symbol is shown, on the removable access cover, to indicate the position of the ISOFIX/i-Size lower anchorages.

BOOSTER SEATS

In a situation where a child is too large to fit into a child safety seat, but is still too small to safely fit the 3-point belt properly, a booster seat is recommended for maximum safety. Follow the manufacturer's instructions for fitting and use, then adjust the seat belt to suit.

ISOFIX AND I-SIZE ANCHOR POINTS

Do not attempt to fit ISOFIX or i-Size child restraints to the centre rear seating position. The anchor bars are not designed to hold an ISOFIX or i-Size child restraint in this position.

Child safety

To install an ISOFIX or i-Size child restraint:

Raise the head restraint on the relevant rear outer seat position.

Locate the recess at the top of each access cover, lightly pull forward to release and remove. This will now allow access to the vehicle's lower anchor bars.

Note: Store the access covers safely and refit when the child restraint is removed from the vehicle.

Slide the child restraint locking mechanism onto the vehicle's anchor bars and then push the child restraint towards the rear of the vehicle, to make sure of complete engagement.

ISOFIX child restraint system seating positions

child restraint

months

months to 4 years

4 to 12 years

Test the security of the child restraint. To do this, attempt to pull the child restraint away from the vehicle's seat and twist the child restraint from side to side. Even if the child restraint appears secure, you should always check the anchor points visually to confirm correct attachment.

If the child restraint is not correctly anchored, there is a significant risk of injury to the child in the event of a collision or emergency braking.

Note: Always make sure that if an upper tether is provided, it is fitted and tightened correctly.

Note: For child restraints fitted with a support leg, adjust the leg so that it rests firmly on the floor.

FixturesSize classesMass group as shown on the

Second row outboard seats

ILISO/R1E0 Up to 10 kg (22 lb.) 0 to 9

ILISO/R1E0+ Up to 13 kg (29 lb.) 0 to 18

IUFISO/F2B

IUFISO/F2XB1

IUFISO/F3A

Recommended child restraint system

-XISO/L1FCarrycot

-XISO/L2G

Britax/Römer Baby Safe Plus with Baby-Safe ISOFIX Base

-ILISO/R2D

-ILISO/R3C

-ILISO/R2DI 9 to 18 kg (20 to 40 lb.) 9

-ILISO/R3C

Britax/Römer Baby Duo Plus

----II/III 15 to 36 kg (33 to 80 lb.)

Child safety

• IUF = Suitable for ISOFIX forward child

restraint systems of universal category, approved for use in this mass group.

• IL = These ISOFIX child restraint systems

are of the specific vehicle, restricted or semi-universal categories.

i-Size child restraint system seating positions

Seating position

Front Passenger

• i-U = Suitable for i-Size universal child

restraint systems, forward and rearward facing.

• X = Seating position not suitable for i-Size

universal child restraint systems.

INSTALLING TETHER ANCHORAGE CHILD RESTRAINTS

Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses, or for attaching other items or equipment to the vehicle.

Always follow the child seat or restraint system manufacturer’s instructions when fitting tether straps.

When fitting a child seat or restraint system, always pass the tether strap over the top of the seat back and beneath the head restraint.

The vehicle is equipped with tether anchorage points, located behind the top of the second row seatback frames. These should be used to attach straps from child seats or child restraint systems.

• X = Not suitable for ISOFIX child restraint fitment in this mass group.

Note: Ages given are approximate. In case of doubt, the child’s weight, not age, should be used when considering an appropriate child seat.

Rear outboard left

Always fit the upper tether anchorage and tighten correctly.

• Pass the tether strap over the seatback and beneath the head restraint.

right

Make sure that the rear seatback is securely and completely latched to the vehicle, in the normal upright position.

Rear centreRear outboard

Xi-Ui-UXi-Size child restraint system

• Release the access cover for the relevant

tether anchorage point.

• Attach the tether strap hook to the tether anchorage point. Make sure that the tether strap hook is facing the correct way.

• Tighten the tether strap according to the child seat, or the child restraint, manufacturer's instructions.

Child safety

Airbags

AIRBAGS

Front passenger’s airbag.

Front seat side airbag.

Curtain airbags.

Front seat side airbag.

Driver’s airbag.

Note: The general location of airbags fitted to the vehicle are marked by the word AIRBAG.

Always contact a Dealer/Authorised Repairer if:

• An airbag inflates.

• The front or sides of the vehicle are damaged.

• Any part of the airbag Supplementary Restraint System (SRS) shows signs of cracking or damage, including trim covering airbags.

• The amber airbag warning lamp illuminates.

High speed impacts may cause serious injury or death, irrespective of safety features fitted to a vehicle. Always drive with caution and consideration for the vehicle’s characteristics, road and weather conditions, and do not exceed any speed limits in force.

Seat belts should be worn at all times, by the driver and passengers in all seating positions. The airbag Supplementary Restraint System (SRS) cannot provide protection in some types of impact. Under these circumstances, the only protection will be provided by a correctly worn seat belt.

Airbags

AIRBAG OPERATION

For the airbags to operate correctly, the roof lining and door post trims must be in good condition, correctly fitted, and free from obstruction. Any damage, wear, or incorrect fitment should be referred to a Dealer/Authorised repairer as soon as possible for examination and repair.

High speed impacts may cause serious injury or death irrespective of safety features fitted to a vehicle.

Make sure that a gap is maintained between the side of the vehicle, and the head and torso. This will enable unobstructed inflation of the curtain and seat-mounted side airbags.

Airbags inflate at high speeds. To minimise the risk of injury, make sure that all vehicle occupants wear correctly positioned seat belts, sit correctly in the seats, and position the seats as far back as is practical.

Airbag inflation takes place instantaneously and cannot protect against the effects of secondary impacts. Under these circumstances, the only protection will be provided by a correctly worn seat belt.

The airbag SRS cannot provide protection in some types of impact. Under these circumstances the only protection will be provided by a correctly worn seat belt.

Phone systems should only be installed by qualified persons familiar with the operation of, and requirements for, vehicles fitted with SRS. If you are in any doubt, seek advice from your Dealer/Authorised repairer.

Airbag deployment is dependent on the rate at which the passenger compartment changes velocity following the collision. Circumstances affecting different collisions (vehicle speed, angle of impact, type and size of object hit, etc.), vary considerably and will affect the rate of deceleration accordingly.

The SRS is not designed to operate as a result of:

• Rear impacts.

• Minor front impacts.

• Minor side impacts.

• Heavy braking.

• Driving over bumps and pot holes.

Therefore, it follows that considerable superficial damage to the vehicle can occur, without causing the airbags to deploy.

AIRBAG OBSTRUCTION

Do not obstruct the operation of the airbags by placing any part of your person or any objects in contact with, or close to, an airbag module. If the airbag inflates, objects or any part of your person could interfere with the inflation of the airbag or be propelled inside the vehicle, causing injury to the occupants.

Do not allow passengers to obstruct the operation of the airbags by placing feet, knees, or any other part of the body, or any other objects in contact with, or in close proximity to, an airbag module. Do not place objects between the airbag module and the seat occupant.

Airbags

Do not use non-approved seat covers or accessory seat covers that have not been designed for use with airbags. If in doubt, consult your Dealer/Authorised Repairer.

Make sure that a gap is maintained between the side of the vehicle, and the head and torso. This will enable unobstructed inflation of the curtain, and seat mounted side airbags.

Do not attach or position items on, or close to, the roof lining, front seat backrests, or to an airbag cover, which could interfere with the inflation of the airbag or be propelled inside the vehicle, causing injury to the occupants.

Airbags cannot deploy correctly if they are obstructed. Examples of obstructions are:

• Any part of an occupant’s body in contact with, or close to, an airbag cover.

• Objects placed on, or close to, an airbag cover.

• Clothing, sun screens, or other material hanging from grab handles.

• Clothing, cushions, or other material covering seat mounted airbags.

• Seat covers which are not approved by Jaguar, or specifically designed for use with seat mounted airbags.

This list is not exhaustive and it remains the responsibility of the driver and passengers to make sure the airbags are not obstructed in any way.

Note: Unauthorised modification of the vehicle or parts may invalidate the vehicle's warranty.

Note: Curtain airbags will not inflate as a result of frontal or rear impacts alone.

DISABLING THE PASSENGER AIRBAG

(Not Australia)

Note: Disabling the front passenger airbag is market dependent.

The passenger airbag should be disabled only when a child restraint is fitted to the front passenger seat.

Crash test data and statistics show that the safest place for a child to be restrained is in a child seat correctly fitted to the vehicle's rear seat.

Do not use a child restraint on a seat protected by an operational airbag in front of it. Doing so presents a high risk of death or serious injury to the child in the event of an accident.

The front passenger's airbag can be switched on/off, using the interactive controls on the Instrument panel when the vehicle is stationary. See 47, INSTRUMENT PANEL MENU.

Select Passenger Airbag from the Vehicle Set-up menu, located in the Main Menu.

The displayed text and diagram will show the current Airbag On or Airbag Off status. Select Change Setting to toggle between these 2 options.

Airbags

An airbag status Warning lamp display, mounted on the overhead control panel (as illustrated), will display the operational status

* Displays for 60 seconds, then extinguishes.

Note: The Message centre will also display a warning for 4 seconds every time the ignition is switched on.

As soon as the child seat is removed from the front passenger seat, the airbag must be turned on. Failure to do so, will put any front seat passengers at greater risk of death or serious injury in the event of an accident.

When checking the operational status of the front passenger airbag, make sure the ignition is switched on and the warning lamp bulb check period of 8 seconds has elapsed.

Do not fit a child restraint to the front passenger seat if the airbag warning lamp illuminates continuously with the ignition on.

of the passenger airbag, as shown in the table below.

Warning lamp displayPassenger airbag statusSetting

PASSENGER AIRBAG OFFDisabledAirbag Off

ON PASSENGER AIRBAG*ActivatedAirbag On

AIRBAG DEPLOYMENT EFFECTS

When an airbag inflates, a fine powder is released. This is normal and not an indication of a malfunction. The powder may cause irritation to the skin and should be thoroughly flushed from eyes and any cuts or abrasions. This powder can cause breathing difficulties for asthma sufferers or other people with respiratory problems. If this occurs, get out of the vehicle as soon as it is safe to do so or get fresh air by opening a window. If breathing problems persist, seek medical attention.

Airbag deployment is accompanied by a very loud noise which may cause discomfort and temporary loss of hearing.

After inflation, some airbag components will be very hot. Do not touch the airbag components until they have cooled sufficiently.

FRONT AIRBAGS

The front passenger and driver airbags deploy depending on the severity of the frontal impact.

Airbags

SIDE AND CURTAIN AIRBAGS

These are designed to protect the thorax region of the torso and will deploy only in the event of a side impact and then, only on the side of the impact.

The curtain airbags are deployed in side impact providing greater protection from serious head injuries.

AIRBAG WARNING LAMP

The airbag warning lamp is mounted in the Instrument panel and will illuminate as a bulb check when the ignition is switched on. See 53,

AIRBAG (AMBER).

The warning lamp indicates a potential fault with the vehicle restraint system which could result in serious injury or death in the event of a severe accident.

If the warning lamp indicates that a fault is present in the system, do not use a child restraint on the front passenger seat.

If any of the following warning lamp conditions occur, the vehicle should be checked by your Dealer/Authorised repairer immediately:

• The warning lamp fails to illuminate when the START/STOP button is initially switched on.

• The warning lamp fails to extinguish within 6 seconds of the START/STOP button being switched on.

• The warning lamp illuminates at any time, other than during the bulb check.

When the ignition is switched on, a diagnostic control unit monitors the readiness of the system's electrical circuits. The elements of the Supplementary Restraint System (SRS) components include:

• SRS warning indicator.

• Rotary coupler.

• Airbag modules.

• Front and second row outboard seat belt pre-tensioners.

• Airbag diagnostic control unit.

• Crash sensors.

• Airbag wiring harnesses.

• Front seat buckle switches.

• Front seat track position sensor.

• Airbag status indicator.

AIRBAG SERVICE INFORMATION

Do not attempt to service, repair, replace, modify, or tamper with, any part of the SRS. This includes wiring or components in the vicinity of SRS components. Doing so may cause the system to trigger, or render the system inoperative.

Do not use any electrical test equipment or devices in the vicinity of SRS components or wiring. Doing so may cause the system to trigger, or render the system inoperative.

All of the following operations should only be carried out by a Dealer/Authorised Repairer, or suitably qualified personnel:

• Removal or repair of any wiring or component in the vicinity of any SRS components.

• Installation of electrical, or electronic, equipment and accessories.

• Modification to the front or sides of the vehicle's exterior.

• Attachment of accessories to the front or sides of the vehicle.

DISABILITY MODIFICATIONS

Occupants with disabilities which may require modification of the vehicle, must contact a Dealer/Authorised Repairer before any modifications are made.

Airbags

Instrument panel

INSTRUMENT PANEL

Speedometer: This can be adjusted to display mph or km/h via the Instrument Display and Digital Speedometer Instrument panel menus. See 47,

INSTRUMENT PANEL MENU.

Tachometer.

Message centre and menu display: The Language and Temperature Units can be changed via the Instrument Display Instrument panel menu.

Fuel gauge: See 53, LOW FUEL WARNING (AMBER).

Never allow the engine to run out of fuel. The resultant misfire can seriously damage the catalytic converter.

ECO data system: Status display for the accelerator pedal, engine revolution speed, and brake pedal application.

Note: This display is enabled when ECO driving mode is selected. See 135, ECO.

The trip computer information is also displayed in this area. See 48, TRIP

COMPUTER.

Gear selector status.

Temperature gauge: If the temperature gauge pointer moves into the red section at the top of the scale, the engine is overheating. Stop the vehicle as soon as safety permits and allow the engine to idle until the temperature reduces. If, after several minutes, the temperature does not reduce, switch off the engine and allow it to cool. If the problem persists, seek qualified assistance immediately.

Serious engine damage can occur if the vehicle is driven while the engine is overheating.

Note: At high engine temperatures, there may be a noticeable reduction in engine power and the Air Conditioning (A/C) may cease operation. This is a normal operating strategy, to reduce load on the engine and assist with cooling.

Warning lamps and indicators display: The other warning lamps are displayed within the speedometer and tachometer.

Instrument panel

INSTRUMENT PANEL MENU

A number of vehicle features and display settings may be configured via the Instrument panel menus.

Note: Some of the feature menus listed below may differ due to the vehicle's specification.

To display and navigate through the Instrument panel menus, operate the steering wheel menu control buttons.

Steering wheel menu control buttons:

• Press the MENU/OK button to display the Main Menu.

• Press the relevant up or down arrow button to scroll through the currently displayed menu list. The current selection will be highlighted.

• Press the right arrow button to view a sub-list.

• Press the left arrow button to return to the previous menu.

• Press the MENU/OK button to select the highlighted item.

Close Menu: Select to close the Main Menu

and return to the normal Message centre display.

Select to access the Driving Features menu list.

Select to access the Trip Computer menu list.

Select to access the Instrument Display menu list.

Note: Some personalisation options may not be available in all markets.

Select to access the Head Up Display (HUD) menu list.

Select to access the Vehicle Set-up menu list.

Before making any changes to the vehicle's set-up, you must make sure that you have read and fully understood the relevant topics/sections of the handbook. Failure to do so could lead to serious injury or death.

Select to access the Vehicle Info menu list.

Note: Can only be accessed when the engine is not running.

WARNING AND INFORMATION MESSAGES

Do not ignore warning messages; take appropriate action as soon as possible. Failure to do so may result in serious damage to the vehicle. If the message is suppressed, an amber or red warning icon will remain illuminated until the cause of the message is rectified.

Instrument panel

For information regarding the individual messages, their meanings, and any action required, please refer to the relevant section within this handbook.

If more than 1 message is active, each is displayed in turn for 2 seconds, in order of priority.

Note: Messages are displayed in order of importance. High importance warning messages are given the highest priority.

Warning messages may be accompanied by an audible warning, and the message text may have the handbook symbol next to it. Warning messages are displayed until the condition causing the fault is rectified or the message is suppressed using the OK button on the steering wheel.

TRIP COMPUTER

The computer memory stores data for a journey, or series of journeys, until it is reset to zero.

There are 3 trip memories available, A, B, and Auto.

See 47, INSTRUMENT PANEL MENU. The Trip Computer menu options are listed below:

• Toggle between Trip A, Trip B, or Trip Auto.

• Units: Select to display and choose the

required incremental figures for, distance, speed, and fuel consumption.

• Trip Content: Select to switch the content on/off for, Trip distance, Average speed,

Average consumption, Instantaneous consumption, Distance to empty, and Driving style.

USING THE TRIP COMPUTER

A short press (1 second or less), or a series of short presses of the button will change the trip computer display. The options available are:

• Date and Odometer.

• Trip distance.

• Average speed.

• Average consumption.

• Instantaneous consumption.

• Distance to empty.

• Driving style.

• ECO data system status display.

Note: These options can be enabled/disabled via the Instrument panel menu (Select Trip Computer and then Trip content), except for the ECO data system's status display and the Date and Odometer options.

To reset the trip computer values to zero, press and hold the button for 2 seconds.

To reset the fuel consumption value, press and hold the button until the display clears.

The distance, average speed, and average fuel economy values for trip A and trip B can be reset. Set the trip computer display to show the trip that you wish to reset, then press and hold the button until the message Resetting trip is displayed.

It is not possible to manually reset the Auto trip memory. This resets automatically each time the ignition is switched on.

Instrument panel

Trips may be added together, or removed, to record a continuous journey. Press the button for longer than 1 second, when Auto trip memory values for distance, average speed, and average fuel economy are displayed, then Adding last journey or Removing last journey will appear on the screen. Press the button for longer than 1 second, and the previous trip information will be added to, or removed from, the current trip and the new total will be displayed. There is no limit to the number of times this can be done before the ignition is switched off.

TRIP DISTANCE

Distance travelled since the last memory reset. The maximum trip reading is 9999.9 (kilometres or miles). The computer will automatically reset to zero if this distance is exceeded.

RANGE

This shows the predicted distance (kilometres or miles) that the vehicle should travel on the remaining fuel, assuming fuel consumption and driving style remain constant.

METRIC/IMPERIAL/MIXED DISPLAY

The trip computer readings can be changed between metric, imperial, and mixed units in the Trip Computer menu of the Message centre. See 47, INSTRUMENT PANEL MENU.

Note: The temperature display can be changed between °C (Celsius) and °F (Fahrenheit), independently of Metric or Imperial units.

HEAD UP DISPLAY

The Head Up Display (HUD) feature projects driver information onto the inside of the windscreen.

If enabled, the HUD information displayed is as follows:

Current gear selected.

Follow mode is active. See 129, ENTERING FOLLOW MODE.

Cruise control set speed.

Cruise control or Adaptive Cruise Control (ACC) is active.

Traffic sign recognition, identified speed limit. See 140, TRAFFIC SIGN

RECOGNITION.

Current vehicle speed.

Turn-by-turn navigation instructions.

Note: Do not place anything over the HUD unit, which is positioned above the Instrument panel next to the windscreen.

If cleaning is required, see 77, TOUCH SCREEN CARE and follow the same cleaning instructions.

The Head-Up Display (HUD) (Instrument panel) menu options are listed below:

• HUD: Select to switch on or off.

Instrument panel

• HUD options: Select to choose which features to display, Cruise control, Navigation, Traffic Signs, and Gear state.

• HUD brightness: Select to adjust, via the steering wheel buttons. Select OK to confirm.

• HUD position: Select to adjust, via the steering wheel buttons. Select OK to confirm.

Warning lamps

WARNING LAMPS AND INDICATORS

RED warning lamps are for primary warnings. A primary warning must be investigated immediately by the driver or qualified assistance, before continuing.

AMBER and YELLOW warning lamps are for secondary warnings. Some indicate that a vehicle system is in operation, others indicate that the driver must take action and then seek qualified assistance as soon as possible.

GREEN and BLUE lamps within the Instrument panel indicate system status.

LAMP CHECK

A warning lamp bulb check is initiated when the ignition system is switched on and lasts for 3 seconds (except for the airbag warning lamp which will remain on for 6 seconds). If any warning lamp remains on after this period, investigate the cause before driving.

Some warning lamps have associated messages displayed in the Message centre.

Note: Not all warning lamps are included in the check (e.g., high beam headlamps and direction indicators).

Note: If a trailer with LED lights is connected to the trailer socket, the bulb check may not be performed.

CRITICAL WARNING MESSAGE (RED)

Illuminates when a critical warning message is available in the Message centre.

GENERAL WARNING/INFORMATION MESSAGE (AMBER)

Illuminates when a non-critical warning message or an information message is available in the Message centre.

ENGINE TEMPERATURE (RED)

Illuminates when the engine's temperature is too high. The Message centre will also display the message ENGINE OVERHEATING.

Stop the vehicle as soon as safety permits and seek qualified assistance before continuing.

LOW OIL PRESSURE (RED)

If the lamp flashes or illuminates while driving, stop the vehicle as soon as safety permits and switch off the engine immediately.

Check and top up the oil level, if necessary. Start the engine, if the lamp remains illuminated, switch the engine off immediately and seek qualified assistance before continuing.

BRAKE (RED)

Illuminates briefly as a bulb check, when the ignition is switched on.

If the lamp illuminates while driving, suspect low brake fluid level or a fault with the Electronic Brake force Distribution (EBD) system.

Stop the vehicle as soon as safety permits and check and top up the brake fluid, if necessary. If the lamp remains illuminated, seek qualified assistance before continuing.

Warning lamps

BRAKE (YELLOW)

Illuminates with a message, to indicate worn brake components.

The message, Brake Pads Worn, may appear in the Message centre.

In the event that this message is displayed, drive carefully and seek qualified assistance at the earliest opportunity.

Note: If the lamp illuminates without a message, then a fault has been detected with the brake wear system. Drive carefully and seek qualified assistance at the earliest opportunity.

PARKING BRAKE (RED)

Illuminates when the Electric Parking Brake (EPB) is correctly applied. If the lamp flashes, a fault has been detected. Seek qualified assistance urgently.

BATTERY CHARGE (RED)

Illuminates as a bulb check, when the ignition is switched on and extinguishes when the engine is started.

If the lamp remains on or illuminates while driving, there is a fault with the battery charging system and a message will be displayed in the Message centre. Seek qualified assistance urgently.

SEAT BELT (RED)

Illuminates, accompanied by a chime, when the vehicle is in motion and an occupied front seat belt is unbuckled.

The lamp will extinguish when the relevant seat belt is buckled.

Note: Objects on the front passenger seat may activate the Seat belt reminder feature. It is recommended that any objects placed on the front passenger seat are secured using the seat belt. See 29, USING THE SEAT BELTS.

LANE DEPARTURE WARNING (RED)

If the Lane departure warning system detects that the vehicle has crossed either of the lane markings that it is travelling within, without activation of the appropriate direction indicator, then the relevant lane will illuminate red. This will also be accompanied by a vibration felt through the steering wheel.

ENGINE/TRANSMISSION (AMBER)

Illuminates briefly as a bulb check, when the ignition is switched on.

If the lamp illuminates when the engine is running, there is an emissions related fault with the engine or transmission. The vehicle can be driven but may enter limp-home mode with the possibility of reduced performance. Seek qualified assistance as soon as possible.

If the warning lamp flashes while the engine is running, reduce speed and seek qualified assistance urgently.

GLOW PLUGS (AMBER)

Illuminates when the ignition is switched on, to indicate that the glow plugs are active.

Warning lamps

DYNAMIC STABILITY CONTROL (DSC) (AMBER)

Flashes when DSC is active.

If there is a fault, it will remain illuminated and the Message centre will display DSC NOT AVAILABLE. The vehicle can still be driven, but without DSC assistance. Seek qualified assistance as soon as possible.

DYNAMIC STABILITY CONTROL (DSC) OFF (AMBER)

Illuminates when DSC is switched off. A chime will sound and a confirmation message will be displayed in the Message centre.

ANTI-LOCK BRAKING SYSTEM (ABS) (AMBER)

Illuminates briefly as a bulb check, when the ignition is switched on.

If the lamp remains on or illuminates while driving, there is a fault with the ABS system. Drive with care, avoiding heavy brake application and seek qualified assistance urgently.

AIRBAG (AMBER)

ADAPTIVE FRONT LIGHTING SYSTEM (AMBER)

Illuminates when there is a system fault. The headlamps will still operate, but without this feature operating correctly. Seek qualified assistance as soon as possible.

REAR FOG LAMP (AMBER)

Illuminates when the rear fog lamps are switched on.

LOW FUEL WARNING (AMBER)

Illuminates when the fuel level is low. Refuel at the earliest opportunity.

The arrow shows which side of the vehicle to locate the fuel filler cap.

AUTOMATIC SPEED LIMITER (AMBER)

Illuminates when the Automatic Speed Limiter (ASL) is active.

FOLLOW MODE (AMBER)

Illuminates when the Adaptive Cruise Control (ACC) system is in Follow mode.

Illuminates as a bulb check, when the ignition is switched on and extinguishes when the engine is started.

If the lamp illuminates when driving, there is a fault with the airbag system. Seek qualified assistance as soon as possible.

EXTERNAL TEMPERATURE (AMBER)

Illuminates when the external temperature is low enough that ice may be present on the road.

Warning lamps

PROGRESS CONTROL SYSTEM (AMBER)

Illuminates to confirm that the Progress control system is enabled.

TYRE PRESSURE MONITORING SYSTEM (YELLOW)

The warning lamp illuminates, accompanied by a message in the Message centre, to warn that 1 or more tyres are significantly under-inflated.

Stop the vehicle as soon as possible, check the tyre pressures and inflate to the recommended pressure.

The lamp will flash to indicate a system fault.

HIGH BEAM (BLUE)

Illuminates when the high beam headlamps are switched on or flashed.

LANE DEPARTURE WARNING (GREEN)

Illuminates green to indicate that the Lane departure warning system has recognised a lane marking. Illuminates grey to confirm the system is enabled, or if lane markings have not been recognised.

SIDE LAMPS (GREEN)

Illuminates when the side lamps are switched on.

AUTO HIGH BEAM (GREEN)

Illuminates when the Auto high beam feature has switched on the vehicle's high beams.

DIRECTION INDICATORS (GREEN)

The appropriate warning lamp will flash when the direction indicators are operated.

INTELLIGENT STOP/START (GREEN)

Illuminates when the engine is shut down by the Intelligent stop/start system.

Note: Other warnings normally associated with an engine shutdown, for example, the ignition warning lamp, will not illuminate during an engine shutdown by the Intelligent stop/start system.

GEAR SHIFT (GREEN)

The gear shift indicator illuminates briefly at the recommended gear change point (up-shift).

The gear shift indicator will not illuminate when Cruise control is active and is not being overridden by pressing the accelerator pedal.

Note: This warning indicator is only a guide. It remains the responsibility of the driver to operate the vehicle in an appropriate manner for the prevailing conditions.

CRUISE CONTROL (GREEN)

Illuminates when Cruise control or Adaptive Cruise Control (ACC) is active.

FORWARD ALERT (GREEN)

Illuminates when Forward alert is active.

TRAILER DIRECTION INDICATORS (GREEN)

Illuminates as a bulb check, when the ignition is switched on and extinguishes when the engine is started.

If a trailer is attached, the warning lamp will flash in conjunction with the direction indicator warning lamp. If the lamp fails to flash, the direction indicator bulb on the trailer may be faulty.

Note: If a trailer with LED lights is connected to the trailer socket, the bulb check may not be performed.

Warning lamps

Exterior lights

LIGHTING CONTROL

With the headlamps on, push the control away from the steering wheel to select high beam. The Instrument panel warning lamp will illuminate. See 54, HIGH BEAM (BLUE).

Note: Do not use high beam where it may distract other road users.

Pull the control towards the steering wheel and release to flash the high beam on and off. The high beam will remain on for as long as the switch is held.

Side lamps: Rotate the control to this position to switch the side lamps on. The Instrument panel warning lamp will illuminate. See 54, SIDE LAMPS (GREEN).

Headlamps: Rotate the control to this position to switch the headlamps on.

AUTO: With Auto lamps selected, when the

ambient light fades and the ignition is on, the side lamps, tail lamps, dipped beam headlamps and licence plate lamps will switch on automatically. Headlamp courtesy delay, High beam assist and the Windscreen wipers detection may also be activated.

Note: Low exterior light levels, caused by adverse weather conditions, may also cause the Auto lamps to activate.

Rear fog lamps: Will operate only while side lamps, headlamps or Auto lamps are selected. Turn the collar towards the steering wheel and release. The Instrument panel warning lamp will illuminate. See 53, REAR FOG LAMP (AMBER). To switch the rear fog lamps off: Turn the collar towards the steering wheel again and release.

INSTRUCTIONAL VIDEO

Exterior lights

DAYTIME RUNNING LAMPS

With the lighting control in the OFF position or in the AUTO position, while the lighting conditions do not require the headlamps to be on, then the Daytime running lamps will switch on automatically under the following conditions:

• The engine is running.

• The gear selector is out of Park (P)

(automatic transmission).

• The Electric Parking Brake (EPB) is not applied - market dependent.

Unless required or prohibited by law, the Daytime running lamps feature can be disabled or enabled by a Dealer/Authorised Repairer.

The Daytime running lamp, within the Xenon headlamp unit, is a Light Emitting Diode (LED) lamp and should only be replaced or maintained by qualified personnel.

Note: The Halogen headlamp's high beam bulb has 2 filaments, one is for the high beam and the other is for the Daytime running lamp. See

188, HEADLAMP BULB REPLACEMENT HALOGEN HIGH BEAM.

HEADLAMP COURTESY DELAY

This feature operates whenever the lighting control is in the AUTO (5) position and the ignition is switched off. The headlamps will remain illuminated for up to 240 seconds.

Note: The time delay may be changed via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

The courtesy delay can be switched off at any time, by pressing the headlamp button on the Smart key.

AUTO HIGH BEAM

This feature of the Xenon lighting automatically selects and deselects the high beam, under specific conditions of road lighting and in the absence of other vehicle’s lights. The system is only active when the ambient light drops below a predetermined level.

Note: It is not recommended that Auto high beam is used while driving off road.

For Auto high beam to become operational, the lighting control must be in the AUTO (5) position, with dipped beam headlamps selected.

The Instrument panel warning lamp illuminates when Auto high beam is selected. See 54, AUTO HIGH BEAM (GREEN).

Auto high beam will only activate when the vehicle's speed exceeds 40 km/h (25 mph). The system will deactivate when the vehicle's speed drops below 24 km/h (15 mph).

To manually select high beam, move the lighting control to the high beam position as normal. To return to Auto high beam, move the lighting control back to the central position.

To manually override to dipped beam from high beam, pull the lighting control to the flash position (2) and Auto high beam will be cancelled. To return to Auto high beam, push the lighting control to the high beam position (1) and then return it to the central position.

To switch Auto high beam off, turn the lighting control from Auto to headlamps.

This feature can be disabled/enabled via the Driving Features and Auto High Beam Instrument panel menus. See 47, INSTRUMENT

PANEL MENU. Use the Vehicle Info and AHB Sensitivity menus to select either the Normal Mode or the Test Mode.

The following may affect the operation of Auto high beam:

• Highly reflective road signs.

Exterior lights

• Dimly lit road users, for example, cyclists or pedestrians.

• Adverse weather conditions, for example, rain or fog.

• Dirty or obscured sensor.

• Dirty, damaged or misted windscreen.

• Oncoming vehicles partially obscured by a central motorway barrier.

Note: The system cannot be relied upon to activate or deactivate high beam in all possible circumstances. It remains the driver’s responsibility to use the headlamps correctly at all times.

Note: Make sure that the forward-facing sensors on the back of the rear-view mirror are not blocked or obstructed.

WINDSCREEN WIPER DETECTION

If Auto lamps is selected and the windscreen wipers are switched on for 20 seconds or more, the side lamps, tail lamps and headlamps will switch on automatically. When the wipers are switched off, the lamps will automatically switch off 2 minutes later.

HEADLAMPS - CONDENSATION

Misting of lamp lenses can occur under some atmospheric conditions. This will not affect the performance of the lamps and will clear during normal operation.

HEADLAMPS - DRIVING ABROAD

The headlamp beam pattern is suitable for driving on either side of the road. There is no need for any mechanical adjustment or external decals.

HEADLAMP LEVELLING

Use the rotary control to set the Halogen headlamps position to the correct level for the current vehicle load. This is located on the driver's side lower fascia.

Note: Not available for all markets.

Switch positionVehicle load

0Driver only

1Driver and front seat

passenger

2Driver and passengers

in all seats

3Maximum gross

vehicle weight

3Maximum rear axle

load

ADAPTIVE FRONT LIGHTING SYSTEM (AFS)

With the headlamps on, the AFS will adjust the beams when cornering, to provide an improved illumination in the direction of travel.

The AFS is deactivated when:

• Reverse (R) gear is selected.

• The vehicle is stationary.

If a system fault is detected, the headlamps will

attempt to move to the central position and then remain stationary. The AFS warning indicator will illuminate to indicate that a fault is present. See 53, ADAPTIVE FRONT LIGHTING SYSTEM (AMBER).

If the warning lamp illuminates, contact a Dealer/Authorised Repairer as soon as possible.

Exterior lights

Interior lights

INTERIOR LIGHTS

Front seat footwell lamps.

Glovebox lamp: Open to illuminate.

Vanity mirror lamps: Lift the sun visor flap to illuminate.

Rear seat footwell lamps.

Front reading lamps: Touch the lens briefly to switch on/off.

Front interior courtesy lamp: Touch the lens briefly to switch on/off.

Rear interior courtesy lamp.

Rear reading lamps: Press the appropriate button to activate a reading lamp manually. Press again to switch off.

Interior lights

All the interior lamps (except for the glovebox and the vanity mirror lamps) illuminate automatically when the vehicle is unlocked, or a door is opened. They will extinguish approximately 20 seconds after all of the doors are closed, or when the vehicle is locked.

To switch the automatic illumination of the interior lamps off/on, continue to touch the front interior lamp lens (6) until the lamp flashes.

INTERIOR LIGHTS OFF or INTERIOR LIGHTS AUTO will be displayed in the Message centre

accordingly.

Note: The puddle lamps (mounted at the base of each door) and the Luggage compartment lamps are automatically operated when a door or the luggage compartment is opened. The on/off status of the interior lamps' automatic illumination, will not affect the operation of these lamps.

INTERIOR LIGHTS INTENSITY

Use the rotary control to adjust the intensity of the instrument illumination. The exterior lamps must be switched on while changes are being made. See 288, DRIVER CONTROLS.

Once enabled, Stealth mode is activated by switching the Touch screen off. If night time conditions exist when the Touch screen is switched off, the interior switch illumination and the Instrument panel illumination will automatically reduce to their minimum levels. Stealth mode will be deactivated if night time conditions no longer exist, or if the Touch screen is switched back on.

Note: The interior illumination control will not operate while Stealth mode is active. See 288, DRIVER CONTROLS.

AMBIENT LIGHTING

The ambient lighting can be adjusted for colour and intensity via the Touch screen Extra

features menu. See 76, TOUCH SCREEN CONTROLS. The exterior lamps must be

switched on while changes are being made.

STEALTH MODE

Stealth mode lowers the level of interior illumination to aid night time driving. Stealth mode can be enabled through the Touch screen

Extra features menu. See 76, TOUCH SCREEN CONTROLS.

Wipers and washers

WIPER OPERATION

Do not operate the wipers on a dry screen.

To avoid damage to the bonnet, do not lift the wipers when they are in the normal parked position. See 198, WIPERS SERVICE POSITION.

Remove any snow, ice, or frost from the windscreen, around the wiper arms and blades, and the windscreen scuttle, before operating the wipers.

Vehicles with a rain sensor

Automatic Rain sensing mode: The front wipers will respond and adapt automatically to the ambient rain conditions, selecting the appropriate wiper frequency for the prevailing conditions. The sensitivity of the system can be adjusted by rotating the collar (2).

Make sure the wipers are switched off before entering a car wash. If the automatic Rain sensing system operates during the car washing process, damage may occur to the wiper mechanism.

Rotate the collar to adjust the sensitivity of the automatic Rain sensing mode when position (1) is selected. The higher the sensitivity position the more responsive the system will become. When automatic Rain sensing mode is selected, or when sensitivity is increased, the system will perform a single wipe.

Low speed continuous wipe.

High speed continuous wipe.

Single wipe of the windscreen, or hold down for further continuous wipes.

Windscreen wash/wipe: Pull and release to operate the front washers and wipers. The wipers will operate for 2 further wipes after the wiper/washer control is released. After a few seconds, a drip wipe will clear any residual washer fluid from the windscreen. If more washer fluid is required, pull and hold the wiper/washer control position.

Note: The front wipers will not operate while the bonnet is open.

Vehicles without a rain sensor

Intermittent wipe: The time delay between wipes can be adjusted by rotating the collar (2).

Make sure the wipers are switched off before entering a car wash. If the wipers operate during the car washing process, damage may occur to the wiper mechanism.

Rotate the collar to adjust the time delay between wipes when position (1) is selected. The higher the setting, the more frequently wipes will occur.

Note: Wipe frequency will increase with vehicle speed.

Low speed continuous wipe.

High speed continuous wipe.

Single wipe of the windscreen, or hold down for further continuous wipes.

Note: The front wipers will not operate while the bonnet is open.

Note: If the wipers leave smears on the glass after the vehicle has been washed, this may be due to wax or other residue. Should this occur, clean the glass with the recommended screen cleaning fluid. See 248, LUBRICANTS AND

FLUIDS.

Note: The windscreen will no longer be wiped

effectively and the automatic Rain sensing function will degrade if the wipers become worn. Always replace worn or damaged wiper blades as soon as possible. The wipers service position will move the wipers to allow wiper blade replacement. See 198, WIPERS SERVICE

POSITION.

Note: If the wiper blades become stuck or

jammed, an electronic cut-out will temporarily halt the wiper's operation. If this happens, switch off the wipers and the vehicle's ignition, when safe to do so. Clear any obstructions and free the wiper blades, before attempting to switch on the ignition.

SPEED-DEPENDENT MODE

If the vehicle's speed drops below 8 km/h (5 mph) with the wipers operating, the wipers will switch to the next lowest speed. When the vehicle's speed increases to over 8 km/h (5 mph), the original wiper speed setting will be restored.

Wipers and washers

Vehicles without a rain sensor fitted will also increase the frequency of the intermittent front wipe when the vehicle's speed increases.

This feature can be enabled/disabled by a Dealer/Authorised Repairer.

RAIN SENSOR

The wiper's rain sensor (if fitted) is mounted on the inside of the windscreen, behind the rear-view mirror. The sensor is able to detect the presence and amount of water on the windscreen, and automatically activate the windscreen wipers accordingly.

Note: Static droplets may not be detected on initial start-up. A single wipe should be used to clear the windscreen.

Note: The Wiper Rain Sensor can be enabled/disabled via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

To activate the rain sensitive wipers, move the wiper/washer control to the AUTO position. The behaviour of the system may be adjusted to the driver's preference by rotating the collar (2).

Note: If the wiper/washer control is turned to the AUTO position, the wipers will not operate if either of the front doors are open.

Note: In dry and often sunny conditions, optical influences and dirt accumulation on the windscreen may result in the windscreen wipers activating inadvertently. To prevent this, it is recommended that, under these conditions, the wiper/washer controls are returned to the OFF position.

DRIP WIPE

If the drip wipe function is configured, the wipers will operate for a few seconds after a wash/wipe cycle has finished, to clear any remaining drips from the windscreen.

Wipers and washers

This function can be enabled/disabled by a Dealer/Authorised Repairer.

HEADLAMP WASHERS

The optional headlamp power wash operates automatically with the windscreen wash, and will only operate if the headlamps are switched on and there is sufficient washer fluid in the reservoir.

Headlamp wash operates every fourth operation of the screen washers, provided the headlamps are still switched on and approximately 10 minutes have elapsed since the last headlamp wash.

Switching the headlamps or the ignition off and back on again, will reset the cycle. See 56,

LIGHTING CONTROL, or see 100, SWITCHING OFF THE ENGINE.

Note: The headlamps are washed alternately to prevent the washer fluid from reducing the light output from both headlamps simultaneously.

EXTERIOR MIRRORS

Mirrors

Left mirror adjustment.

Right mirror adjustment.

Power-fold/unfold: Press both buttons simultaneously. This feature is inhibited at speeds over 110 km/h (70 mph).

The mirrors can be adjusted and folded when the ignition is on and for up to 5 minutes after the ignition is switched off, provided the driver’s door is not opened.

Press the appropriate button to select the mirror to be adjusted; the button LED indicator lamp will illuminate to confirm which side is active. Use the joystick control to adjust the mirror's glass.

Note: Depending on the type of lens used, distances may be difficult to judge accurately when only using the mirrors.

The mirrors can be configured to automatically fold when the vehicle is locked and unfold when unlocked. This feature can be enabled/disabled by a Dealer/Authorised Repairer.

If the mirrors are accidentally knocked out of position (e.g., so only one is folded), press both buttons simultaneously to re-synchronise.

Note: If the mirrors were folded using the switches, they will not unfold when the vehicle is unlocked.

Mirrors

Note: Up to 3 different exterior mirror positions can be stored and recalled using the Driving position memory feature. See 20, DRIVING POSITION MEMORY.

MIRROR DIP WHEN REVERSING

The mirrors can be configured so that when Reverse (R) gear is selected, the passenger's door mirror is automatically adjusted to provide an improved viewing angle for reversing.

The exact dipped position can be adjusted using the joystick control, when the mirror is dipped. The next time R is selected, the newly adjusted position will be selected.

When the gear selector is moved out of R, or if the vehicle's speed exceeds 12 km/h (7.5 mph) while reversing, the mirror will return to its previous position.

Reverse-dip Mirror can be enabled/disabled via the Vehicle Set-up menu. See 47, INSTRUMENT PANEL MENU.

BLIND SPOT MONITOR

The Blind Spot Monitor (BSM) system is a supplement to, not a replacement for, a safe driving style and use of the exterior and rear-view mirrors. The system may not function under all speeds, weather and road conditions.

The BSM may not be able to give adequate warning of vehicles approaching very quickly from behind or vehicles that are being overtaken rapidly.

The BSM may not be able to detect all vehicles and may also detect objects such as roadside barriers, etc. Drive safely at all times and use the exterior and rear view mirrors to avoid accidents.

The radar sensors may be impaired by mud, rain, frost, ice, snow, or road spray. This may affect the system's ability to reliably detect a vehicle/object within the blind spot.

Make sure the warning indicators in the exterior mirrors are not obscured by stickers or other objects.

Do not attach stickers or objects to the rear bumper, that may interfere with the radar sensors.

Blind spot monitoring

The Blind Spot Monitor (BSM) system monitors a zone that covers the area adjacent to the vehicle, that is not easily visible to the driver. The system uses a radar on each side of the vehicle to identify any overtaking vehicle/object within the blind spot area (1) of the vehicle, while disregarding other objects which may be stationary or travelling in the opposite direction, etc.

If an object is identified by the BSM system as being an overtaking vehicle/object, an amber warning icon (2) illuminates in the relevant exterior mirror, to alert the driver that there is a potential hazard in the vehicle's blind spot and therefore, that a lane change might be dangerous.

The radar monitors the area extending from the exterior mirror rearwards, to approximately 6 m (20 ft) behind the rear wheels and up to 2.5 m (8.2 ft) from the side of the vehicle (the width of a typical carriageway lane). The BSM is designed to work most effectively when driving on multi-lane roads.

Blind spot monitoring

Note: This radar sensor is approved in all RTTE countries.

Note: The system covers an area of a fixed lane width. If the lanes are narrower than a typical carriageway lane, objects travelling in non-adjacent lanes may be detected.

Note: If rapidly overtaking vehicles are detected on both sides simultaneously, the warning icons in both mirrors will flash.

The BSM automatically switches on and becomes active when the vehicle is travelling at more than 10 km/h (6 mph) in a forward gear. When the system initiates, it performs a self-check, during which the warning icons in the mirrors illuminate alternately for a short period of time.

The indicator dot (3) remains illuminated until the vehicle's forward speed exceeds 10 km/h (6 mph).

The BSM is automatically disabled and an amber warning indicator dot is displayed in the exterior mirrors when:

• Reverse (R) gear is selected.

• Park (P) is selected for vehicles with automatic transmission.

• The vehicle's speed is below 6 km/h (4 mph).

• The Electric Parking Brake (EPB) is applied.

Note: Automatic disabling of the BSM does not apply to vehicles with Reverse Traffic Detection. See 118, REVERSE TRAFFIC DETECTION.

The BSM can be enabled or disabled through the Instrument panel menu. See 47, INSTRUMENT PANEL MENU.

Note: The BSM is disabled when a trailer is attached.

CLOSING VEHICLE SENSING

Closing vehicle sensing is a supplement to, not a replacement for, a safe driving style and use of the exterior and rear-view mirrors.

Closing vehicle sensing may not be able to give adequate warning of vehicles approaching very quickly from directly behind the vehicle. Always use the exterior and interior rear-view mirrors.

The radar sensors may be impaired by mud, rain, frost, ice, snow, or road spray. This may affect the system's ability to reliably detect an approaching vehicle.

Make sure that the warning indicators in the exterior mirrors are not obscured by stickers or other objects.

Do not attach stickers or objects to the rear bumper, that may interfere with the radar sensors.

Blind spot monitoring

In addition to the functionality provided by the Blind Spot Monitor (BSM), Closing vehicle sensing monitors a larger area behind the vehicle. Closing vehicle sensing is designed to perform best on multi-lane motorways with free-flowing traffic and is operational above 13 km/h (8 mph) in a forward gear.

Closing vehicle sensing monitors an area behind the vehicle, up to a distance of 70 m (230 ft) and approximately 2.5 m (8 ft) from each side of the vehicle (the width of a typical carriageway lane).

If a vehicle is detected approaching rapidly, an amber warning icon will flash in the relevant exterior mirror to indicate that there is a potential danger.

When the detected vehicle reaches the area monitored by the BSM, the amber warning icon will illuminate continuously.

Note: If rapidly overtaking vehicles are detected on both sides simultaneously, the warning icons in both mirrors will flash.

Note: Closing vehicle sensing covers an area of a fixed lane width. If the lanes are narrower than a typical carriageway lane, objects travelling in non-adjacent lanes may be detected.

Note: Closing vehicle sensing is disabled when the vehicle is negotiating a tight radius curve.

Note: When the BSM is disabled, Closing vehicle sensing is also disabled. See 47, INSTRUMENT

PANEL MENU.

Note: Closing vehicle sensing is disabled when

a trailer is attached.

Note: This radar sensor is approved in all RTTE countries.

BSM SENSORS

The BSM system will automatically disable if either of the sensors become completely obscured; an amber indicator dot (3) is displayed in the exterior mirror and the message

BLIND SPOT MONITOR SENSOR BLOCKED

appears in the Message centre.

Note: Blockage testing is initiated only when the vehicle's speed is above 10 km/h (6 mph) and will take at least 2 minutes of accumulated driving above this speed, to determine that the sensor is blocked.

If the sensors become blocked, check that there is nothing obscuring the rear bumper and that it is clear from ice, frost, and dirt.

If a fault with one of the radar sensors is detected, an amber warning indicator dot is displayed in the exterior mirror and the message BLIND SPOT MONITOR NOT AVAILABLE is displayed in the Message centre.

Blind spot monitoring

Note: Even if the detected fault affects the radar sensor on only one side of the vehicle, the whole system is disabled. If the fault is temporary, the system will operate correctly once the engine has been switched off and then on again.

If a fault in the system occurs, consult a Dealer/Authorised Repairer.

Garage door opener

RADIO FREQUENCY TRANSCEIVER

In some countries, the Radio Frequency (RF) transceiver is also known as the HomeLink® Universal Transceiver.

The RF transceiver is located in the rear-view mirror. It can be programmed to transmit the signals of up to 3 different hand held transmitters. These can be used to operate garage doors, entry gates, home lighting, security systems, or other RF operated remote devices.

Do not use the RF transceiver with any garage door opener that lacks the safety stop and reverse feature, as required by safety standards.

When programming the RF transceiver to a garage door opener or an entry gate, make sure that the area is clear of people and objects. This will prevent potential harm or damage, as the gate or garage door will activate during programming.

This device may suffer from interference, if operated in the vicinity of a mobile or fixed station transmitter. This interference is likely to affect the hand-held transmitter, as well as the RF transceiver.

For further information, see 72, INFORMATION

AND ASSISTANCE.

BEFORE PROGRAMMING

When programming a remote device that may require you to press and re-press the hand-held transmitter, unplug the device during the programming process, to prevent possible motor failure.

For the best results, fit a new battery to the hand-held transmitter before programming. If the remote device’s receiver is equipped with an antenna, then make sure that the antenna is extended.

PROGRAMMING

To program the RF transceiver:

Switch the vehicle’s ignition on.

Position the hand-held transmitter 25 to 75 mm (1 to 3 inches) from the rear-view mirror.

Simultaneously press and hold the memory button on the hand-held transmitter, and the desired memory button on the RF transceiver. An indicator LED, located on the left side of the mirror, will start flashing slowly.

When the LED starts flashing quickly, release both buttons.

To operate the remote device, press and hold the programmed memory button on the RF transceiver for 2 seconds. If the LED illuminates continuously, the RF transceiver has been programmed successfully, and the remote device will operate.

Note: You may need to press the button on the RF transceiver up to 3 times.

Garage door opener

If the remote device does not operate, and the LED flashes quickly, further programming will be required.

These extra programming steps may require assistance from another person.

Locate the smart/learn program button on the remote device you wish to program.

Note: The name and location of this button may vary, depending on the manufacturer of the remote device.

Press and release the smart/learn program button and, within 30 seconds, press and hold the desired memory button on the RF transceiver for 2 seconds.

Note: You may need to press and hold the memory button on the RF transceiver for 2 seconds, a further 2 times.

Note: Some entry gate systems require you to cycle (press and re-press) the hand-held transmitter every 2 seconds during programming. If this is the case, continue to press and hold the memory button on the RF transceiver until the LED flashes quickly.

The RF transceiver should now be programmed. Repeat the programming steps, if you wish to add further remote devices to the RF transceiver.

To operate a programmed remote device, press and hold the relevant memory button on the transceiver. Release the button when the device starts operating.

TO ERASE ALL PROGRAMMING

To erase all programming from the RF transceiver:

Switch the vehicle’s ignition on.

Simultaneously press and hold memory buttons 1 and 3 on the RF transceiver.

After approximately 10 seconds, the RF transceiver LED will start to flash. At this point, release both memory buttons on the RF transceiver. All programming will have now been erased from the RF transceiver.

Note: Do not press and hold the buttons for longer than 20 seconds.

REPROGRAMMING A SINGLE GARAGE DOOR OPENER BUTTON

To program a remote device to a previously programmed RF transceiver memory button:

Press and hold the desired RF transceiver memory button. After approximately 20 seconds, the LED will start to flash slowly.

Follow the instructions described in step (2) onwards, as described in

PROGRAMMING.

INFORMATION AND ASSISTANCE

It is recommended that when you sell the vehicle, you erase all programming from the RF transceiver.

For information on the range of compatible remote devices, or for assistance, contact your Dealer/Authorised repairer. Alternatively, visit the HomeLink website www.homelink.com.

Note: Retain the original remote feature handset, for future programming requirements.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorised modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

ELECTRIC WINDOWS

Windows

Window switches:

Note: Each switch has a 2-stage operation. Lightly press/pull and hold to manually operate to the required position. Alternatively, press/pull fully and release for fully (one-touch) automatic operation. Fully automatic operation can be halted at any time, by operating the switch again.

• Press the front of the switch to partially/fully open.

• Pull the front of the switch to partially/fully close.

Note: The windows will operate for 5 minutes after the engine is switched off, as long as none of the doors are opened.

Make sure that the Smart key is removed when leaving passengers in the vehicle. This will prevent unsupervised operation of the windows and sunroof, which may result in injury.

Any ice must be removed from the windows before opertaing.

Rear window isolator.

If children are carried in the rear seats, the isolator switch should be used to prevent operation of the rear windows.

Sunroof:

Windows

Note: The front and rear of the switch has a 2-stage operation. Lightly press and hold to manually operate to the required position. Alternatively, press fully and release for fully (one-touch) automatic operation. Fully automatic operation can be halted at any time, by pressing the switch again.

• With the sunroof closed, press the rear of the switch to partially/fully raise the sunroof to the tilt position. Press the rear of the switch again to partially/fully open the sunroof.

Note: If the sunblind is closed, the sunroof switch will also open the sunblind while operating the sunroof.

• With the sunroof open, press the front of the switch to partially/fully close the sunroof to the tilt position. Press the front of the switch again to partially/fully lower the sunroof.

To prevent accidental damage, make sure any roof rack load will not interfere with the opening of the sunroof.

Sunroof blind:

• Press the rear of the switch to partially/fully open.

• Press the front of the switch to partially/fully close.

The sunroof blind can be opened whenever required, but it can only be closed when the sunroof is closed. If the sunroof is partially closed, then the sunblind will only partially close to the same position.

If the sunblind encounters a resistance when closing, it will stop and then (dependent on its current position) it will either partially or fully open, to allow removal of the obstruction and to prevent personal injury or damage to the mechanism. Press and hold the front of the switch, within 10 seconds of the partial or full opening, to override.

Rear screen sun blind.

• Press the switch to deploy.

• Press the switch again to stow.

Note: If a resonance or a booming sound occurs when a rear window is open, lowering an adjacent front window by approximately 25mm (1 inch) will eliminate the condition.

WINDOW ANTI-TRAP PROTECTION

Before closing a window, make sure that no occupants have any part of their body in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.

Anti-trap protection is designed to stop window movement if an obstruction or resistance is detected. Check the window and its aperture and remove any obstructions. The override procedure is, as follows:

Attempt to close the window. Anti-trap will prevent closure and lower the window.

Within 10 seconds, attempt to raise the window again. Anti-trap will prevent closure and lower the window.

Attempt to close the window for a third time, this time holding the switch in the close position. The window will raise while the switch is held. Hold until closed.

Windows

Note: If this procedure fails to remove the blockage, or if the windows do not operate correctly, the window's operation may need to be reset. See 199, WINDOW RESET.

SUNROOF ANTI-TRAP MECHANISM

Before closing the sunroof, make sure that no occupants have any part of their body in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.

If the sunroof encounters a resistance when closing, it will stop and then (dependent on its current position) it will either partially or fully open, to allow removal of the obstruction and to prevent serious personal injury or damage to the mechanism. Press and hold the front of the switch, within 10 seconds of the partial or full opening, to override the anti-trap mechanism.

If the sunroof fails to operate correctly, it may need to be reset. See 198, SUNROOF RESET.

SOLAR ATTENUATING GLASS

Electronic actuating cards, such as toll road payment cards or Radio Frequency (RF) ID tags, can be fixed at the dedicated locations on the inside of the windscreen. If these cards are located at any other part of a solar attenuating windscreen, then the electronic scanners may not recognize them.

The fixing location is at the top of the windscreen, close to the interior rear-view mirror.

Note: It is recommended that the electronic actuating card should be in the size appropriate location, on the driver's side of the windscreen.

Note: Transponders mounted on the front number plate plinth can be used as an alternative, dependent on the market and availability.

Some vehicles may have a windscreen with solar attenuating glass, that filters sunlight by passing it through a special laminated layer.

Touch screen

TOUCH SCREEN CONTROLS

Do not adjust the Touch screen controls, or allow the system to distract the driver, while the vehicle is moving.

Always run the engine during prolonged use of the Touch screen. Failure to do so may discharge the vehicle's battery; preventing the engine from starting.

Avoid spilling or splashing liquids onto the Touch screen.

Note: The Touch screen display and the number of screen pages will vary, depending on the specification of the vehicle.

Note: The Touch screen will remain active until the ignition is turned off and the driver's door is opened.

Press to select the HOME menu screen.

Press to select the General settings menu screen, see 77, GENERAL SETTINGS. If Park assist is fitted, then see 120, PARK

ASSIST.

Status icons: Showing the connected phone's battery level and network signal strength. The Traffic Announcement (TA) icon will also be displayed, if TA is currently switched on. See 144, AUDIO SETTINGS.

Touch the screen or press the button, to select the Media system. If the Media system is already switched on, then touch to select the current media source menu.

Note: When the system is active, current information for the media being played will be displayed.

Clock: The clock can be adjusted via the System option, in the General settings menu.

Touch to select the Climate system. See 79, CLIMATE CONTROL.

The title of the current screen display.

Continually press to scroll through the media source options.

Touch the screen or press the button, to select the Telephone system. See 157, TELEPHONE SYSTEM OVERVIEW.

10.

Touch the screen or press the button, to select the Navigation system. The current destination route, or the NAV MENU screen will be displayed. See 164, THE NAVIGATION SYSTEM. For vehicles without navigation, press to display the Audio menu screen.

11.

Touch the arrow or swipe the screen, to select the next screen to the right. From the

HOME menu screen, this will be the Extra features available on the vehicle. See 78, EXTRA FEATURES.

12.

Touch to select the General settings menu screen.

13.

Indicator for the number of available screens. The solid dot indicates the position of the currently displayed screen.

14.

Touch the arrow or swipe the screen, to select the next screen to the left.

15.

Press to switch the Touch screen on/off. If Surround cameras are fitted, the screen can be switched off in Extra features. See 124,

SURROUND CAMERA SYSTEM.

16.

Press to mute the sound. If Parking aids are fitted, see 115, USING THE PARKING AID.

TOUCH SCREEN USE

Do not use excessive pressure when selecting items on the Touch screen.

Definitions for the various button taps and Touch screen gestures used in this handbook:

• Touch: Briefly touch the screen's surface with your fingertip.

• Touch and hold: Touch the screen's surface for an extended period of time.

• Swipe: Move your fingertip over the screen's surface in a fast linear movement.

• Drag: Touch an object and move it with your fingertip over the screen's surface, without losing contact.

Touch screen

TOUCH SCREEN CARE

Do not use abrasive cleaners on the Touch screen. For approved cleaning products, contact a Dealer/Authorised Repairer.

GENERAL SETTINGS

The General settings menu screen is divided into categories. Touch to display the list of settings for the required system:

• System.

• Display.

• Media.

• Bluetooth.

• Phone.

• Navigation.

• WiFi.

• Climate.

Note: The list will vary, depending on the specification of the vehicle.

SYSTEM SETTINGS

The System settings screen is divided into categories and is selected via the General settings menu:

• Language: Select the language required.

• Time & Date: Select to change the time and

date.

• Volume settings.

• Unit of measurement: Miles or Kilometres.

• Beep: Switch ON/OFF.

• Animations: Switch ON/OFF.

• Automatic text scrolling: Switch ON/OFF.

• Reduced volume during: Switch ON/OFF.

When enabled, this will automatically reduce the vehicle's audio volume during a phone call.

Touch screen

• Screensaver: Switch ON/OFF.

• Dynamic Home Menu: Switch ON/OFF.

• Delete all personal data.

Note: The list will vary, depending on the specification of the vehicle.

EXTRA FEATURES

Touch the required extra feature to display that feature's information or settings screen:

• Timed climate: See 82, TIMED CLIMATE CONTROL.

• Cameras: See 124, SURROUND CAMERA SYSTEM.

• ECO Data: The ECO Data system is designed to help the driver maximise fuel economy by providing on-screen vehicle data. Touch to select the ECO Data home screen. See 135, ECO.

• Valet mode: See 78, SELECTING VALET MODE.

• Ambient lighting: When selected, the ambient lighting in the vehicle can be changed.

• WiFi hotspot: See 162, INCONTROL WI-FI.

• Screen off: Touch to turn the screen off.

Note: The number of extra features will vary, depending on the specification of the vehicle.

Touch Valet mode in Extra features.

Enter a memorable 4-digit PIN. You will be prompted to confirm the PIN. If you wish to cancel the PIN, select Delete. If the PIN is cancelled, or incorrectly entered, you will be prompted to enter the PIN again.

Valet mode activated is displayed to

indicate that the PIN has been accepted.

The luggage compartment is now securely locked in Valet mode and the Valet mode On screen is displayed.

DESELECTING VALET MODE

To deselect Valet mode:

When you re-enter the vehicle, select Valet mode in Extra features.

Enter your memorable 4-digit PIN and touch the OK soft key.

Valet mode deactivated is displayed to indicate that the PIN has been accepted.

• The luggage compartment will return to the previously set security requirement.

• The Touch screen will be enabled.

Note: If the PIN is forgotten, Valet mode can only be deactivated by a Dealer/Authorised Repairer.

SELECTING VALET MODE

Valet mode allows the vehicle to be driven and locked by a parking attendant, without giving access to the luggage compartment. Valet mode also prevents operation of the Touch screen, to prevent access to telephone numbers or navigation addresses.

Each time Valet mode is used, a Personal Identification Number (PIN) must be entered.

To select Valet mode:

CLIMATE CONTROL

Heating and ventilation

Climate: To access the FRONT CLIMATE

screen, touch Climate on the HOME menu screen. See 76, TOUCH SCREEN

CONTROLS.

Front Seats: Touch to select the Climate seats settings screen.

Timed Climate: Touch to select the TIMED CLIMATE settings menu. See 82, TIMED CLIMATE CONTROL.

Touch to switch the Climate control system off.

Windscreen air distribution: Touch to switch on/off.

Air distribution: Touch the upper (face distribution) or lower (body/feet distribution) area to select.

Touch to select the General settings menu, then to access the Climate settings menu.

Press to increase the temperature for the front left side of the vehicle.

Press to synchronise the driver and front passenger climate zone settings.

10.

Heated front screen: Press to switch on/off.

11.

Heated rear screen: Press to switch on/off.

Note: The heated front and rear screens, will operate only when the engine is running.

Heating and ventilation

Do not attach labels to the rear screen. Do not scrape or use abrasive materials to clean the inside of the rear screen.

12.

Air distribution: Press to select the desired air distribution via the FRONT CLIMATE screen.

13.

Press to select the Front Seats Heated/Climate seat menu.

14.

AUTO mode: Press to switch the fully

automatic mode on/off. Dependent on the vehicle’s specification, the various options for AUTO mode can be set via the Climate settings.

15.

Press repeatedly to increase the temperature for the front right side of the vehicle.

16.

Press repeatedly to decrease the temperature for the front right side of the vehicle.

17.

A/C: Press to switch the Air conditioning

(A/C) system on/off.

18.

MAX A/C: Press to switch the maximum

A/C mode on/off.

19.

Press to increase the blower speed.

20.

Press to decrease the blower speed.

21.

Press to switch the maximum defrost for the windscreen on/off.

22.

Recirculation: Press for timed recirculation (recirculation will operate for 4 minutes) or press and hold for continuous recirculation. Press again to switch off.

Note: Prolonged use at low temperatures may cause the windows to mist

23.

Press to decrease the temperature for the front left side of the vehicle.

Note: Some of the hard keys will have an LED indicator lamp that will illuminate to confirm selection.

INSTRUCTIONAL VIDEO

CLIMATE SETTINGS

Touch the General settings menu soft key on the FRONT CLIMATE menu screen and then select Climate. See 79, CLIMATE CONTROL.

• Auto sensitivity: The Air quality sensor, for Automatic recirculation, can be set to Low, Medium or High. Select Off to disable Automatic recirculation.

• Auto power: The blower speed for automatic operation can be set to Low, Medium or High.

• Auto heated screens: The automatic operation of the front and/or the rear heated screens can be enabled/disabled.

Note: Selection of the ECO driving mode may automatically alter some status and settings for these menus (dependent on previous selections). See 135, ECO.

AUTOMATIC RECIRCULATION

If an Air quality sensor is fitted, the Climate control system will monitor exterior air pollution and select recirculation if it reaches a predetermined level. This feature only operates when selected from the Settings menu. Recirculation sensitivity can also be changed in the Settings menu. See 81, AIR QUALITY SENSOR.

Pressing the recirculation button will not deactivate automatic recirculation.

Heating and ventilation

AIR QUALITY SENSOR

The sensitivity of the Air quality sensor can be adjusted using the Touch screen:

Select Settings from the Climate menu.

Touch the buttons on the screen to increase/decrease sensitivity. To switch off air quality sensing, touch Off.

The auto recirculation icon appears on the Touch screen when the Air quality sensor is switched on.

HEATED SEATS

Note: Seat heaters consume a large amount of battery power. They will only operate when the engine is running.

Note: If fitted, the rear Heated seats (non-climate) can only be operated by pressing the buttons located at the rear of the centre console.

Press the relevant rear Heated seat button, to switch the required seat heater on at the maximum setting. The 3 LED indicators on the button will illuminate.

Press a second time to set the Heated seat at the medium setting; 2 LED indicators will illuminate.

Press a third time to set the Heated seat at the lowest setting; 1 LED indicator will illuminate.

Press a fourth time to switch off.

CLIMATE SEATS

Note: The Heated/Climate seats will only operate when the engine is running.

Touch the Front seats soft key from the Climate menu, or press the Heated/Climate seat button.

Note: The Front seats menu will be displayed.

Note: A seat icon, at the top of the Touch

screen, will change colour to indicate the status of the Climate seats; red for heated operation and blue for cooled operation.

Heated ventilation

• Touch the up arrow icon to switch heated ventilation on at the maximum setting (3 red bars).

• Touch the down arrow icon once or twice to reduce the ventilation setting (2 and 1 red bars).

• Touch the down arrow a third time to switch off heated seat ventilation.

Cooled ventilation

• Touch the down arrow icon to switch cooled ventilation on at the maximum setting (3 blue bars).

• Touch the up arrow icon once or twice to reduce the ventilation setting (2 and 1 blue bars).

• Touch the up arrow a third time to switch off cooled seat ventilation.

Seat zone selection

If fitted with Climate seats, constant selection of the Seat zone soft key will scroll through the 3 choices of seat zone; full seat, cushion, or

back rest only.

AUXILIARY HEATER

The vehicle may be fitted with an Auxiliary heater, which is powered by fuel drawn from the vehicle's tank. The Auxiliary heater operates at low ambient temperatures and helps to boost the temperature of the engine's coolant for improved heater performance. It can also be controlled by the Timed climate control system or from the Timed climate remote control (if fitted).

Heating and ventilation

When the Auxiliary heater is operating, exhaust fumes from the heater may be visible exiting from under the front of the vehicle. This is normal and is not a cause for concern.

Do not operate the Auxiliary heater when refuelling the vehicle. Doing so may cause fuel vapours to combust, causing a fire/explosion.

Do not operate the Auxiliary heater while the vehicle is in an enclosed space. Doing so can cause a build up of highly toxic fumes, which may cause unconsciousness or death.

TIMED CLIMATE CONTROL

The Timed climate control system provides a comfortable temperature inside the cabin in advance of the driver and passengers entering. Dependent on the external temperature, the system draws in fresh air to cool the cabin or operates the auxiliary heater to warm it.

The auxiliary heater is also operated to warm the engine and aid starting in very cold conditions.

Note: If the Auxiliary heater is used to warm the engine, the cabin will not be warmed.

The Timed climate control system is controlled by the Touch screen and can be activated/deactivated by the Timed climate remote control.

The system may not operate or will automatically switch off in the following scenarios:

• If the fuel level is low.

• If the vehicle’s battery charge is low.

• If the coolant temperature is at or above, its required temperature.

SETTING TIMED CLIMATE

The Touch screen can be used to either preset activation times or to operate the system manually.

When the system is operating, the LED in the Climate control AUTO or A/C button will flash. AUTO indicates the engine or cabin are being heated. A/C indicates the cabin is being ventilated. The choice of operation is automatically determined by the system, depending on the external temperature.

Note: The system will cease operation when the engine is started.

To set a Timed climate programme:

Press the HOME MENU button.

Touch the Timed Climate soft key. This soft key may be set on a personal shortcut or accessed via the Extra Features soft key. Select 7 day timer or single event, then select the timer soft key. If the 7 day timer is selected, then select the day for which you want to set a program. Alternatively, select All Week to select the same start time for every day.

Touch the Timer 1 or Timer 2 icon. The timers can be toggled between on and off using the power soft key.

Touch the up or down arrows to set the start time. Hours and minutes are adjusted separately.

Touch OK. The screen will display the activation time. If required, set the time for the other timer using the same process.

Once set, the timer events can be switched on or off, as required, in the Timed climate screen by selecting the 7 day timer or the single event soft key.

Note: Set times should be programmed 20 minutes before the planned journey.

Note: The time format, 12/24 hour clock, is determined by the time settings currently selected in the System settings menu. See 47,

INSTRUMENT PANEL MENU.

Note: Timed climate will only operate once

between engine starts. For example, a remote Timed climate request will not be performed if a programmed Timed climate event has already occurred.

A current heating cycle will be cancelled if the engine is started. Any programmed heating cycle may be cancelled by touching the relevant power soft key on the timer set up menu or the Power soft key on the Timed Climate information home menu.

Heating and ventilation

USING THE TIMED CLIMATE REMOTE

ON button.

OFF button.

Light Emitting Diode (LED) operation indicator.

Antenna.

Note: Avoid touching the antenna when operating the ON or OFF button.

The remote control has an approximate range of 100 metres. There is no need to point the remote control at the vehicle.

Press and hold the ON button for approximately 2 seconds. The LED will illuminate green to confirm that a remote climate program has been initiated. The LED flashes once every 2 seconds to indicate that the heater is active.

The remote Timed climate programme will continue for 20-30 minutes, after which it will switch off automatically to prevent the vehicle's battery from discharging. It also switches off automatically if the engine is started.

The LED indicator signals various states and conditions for the remote Timed climate as follows:

Heating and ventilation

• Illuminates green when the ON button is pressed, then quickly flashes green to indicate that heater operation has been requested.

• Illuminates green followed by red, when the OFF button is pressed, to indicate that the heater has been requested to shut down.

• Illuminates green, then quickly flashes red, when either the ON or OFF button is pressed, to indicate that there is no communication with the receiver. This normally occurs if the vehicle is too far away.

• Illuminates green, then slowly flashes red, when either the ON or OFF button is pressed, to indicate that there is an error.

• Flashes red when either the ON or OFF button is pressed, to indicate the timer climate remote battery needs replacing.

Note: The Timed climate remote will only operate once per engine start to maintain battery condition.

ADDITIONAL REMOTES

Extra remote controls can be programmed to operate the heater. A maximum of 4 remote controls can be programmed to the vehicle. Contact a Dealer/Authorised Repairer to purchase extra remote controls and have them programmed to the vehicle.

REPLACING THE REMOTE BATTERIES

With the front of the remote control facing upwards, press down on the rear of the access cover and push completely off to reveal the battery compartment. Note that the battery should be inserted with the positive side facing upwards. Remove the old battery and making sure that the correct polarity is maintained, insert a new, unused 3 volt CR2032 battery. Align and push the cover back to the original position.

STORAGE COMPARTMENTS

Storage compartments

Glovebox: Pull the release handle to open. The glovebox can be locked/unlocked using the emergency key blade, mounted in the vehicle's Smart key. See 6, UNLOCKING THE VEHICLE.

Note: When Valet mode is selected, the glove box will not open.

Front Cup holders.

Do not drink, or use the cup holders when driving.

Cubby box: Push and hold the release button and then lift to open the cubby box lid. To close, lower the lid and then lightly press to engage the catch.

Rear cup holders: Pull the tag at the top of the stowed rear seat's armrest and lower.

Storage compartments

Front door stowage.

Front seat map pockets.

Rear door stowage.

AUXILIARY POWER SOCKETS

Centre power socket.

Rear power socket.

Luggage compartment power socket.

Only use, Jaguar Land Rover Limited, approved accessories. Using any other equipment may damage the vehicle's electrical system and/or cause battery discharge. If you are in any doubt, contact a Dealer/Authorised Repairer.

The engine should be running when using accessories for long periods. Failure to do so can discharge the battery.

Note: Power sockets can be used to power approved accessories that use a maximum of 120 Watts.

Front power socket.

LUGGAGE ANCHOR POINTS

All items carried in the vehicle should be properly secured.

Securing points are provided in the luggage area to assist in safely securing items.

Note: A range of approved luggage retention accessories is available from a Dealer/Authorised Repairer.

Luggage compartment

Towing

TOWING WEIGHTS

Vehicles supplied with a 3.0L petrol engine, will not facilitate towing.

See 249, WEIGHTS, for details of the Gross Vehicle Weight (GVW), axle weights, and the load in the vehicle's luggage compartment.

Note: The trailer's nose weight should also be considered when calculating the GVW.

Braked trailer

transmission

Braked trailer

transmission

Gross Train Weight (GTW)

transmission

Europe only: When towing, the maximum permissible GVW can be increased by a maximum of 100 kg (220 lb), provided that the road speed is limited to 100 km/h (62 mph) or less.

Note: When calculating the rear axle loading, remember that the trailer's nose weight, the load in the vehicle's luggage compartment, the weight on a roof rack, and the weight of the rear seat passengers must all be added together.

kg (lb)Engine/transmission Variant

750 (1 653)All variantsUnbraked trailers

1 800 (3 968)All variants with automatic

1 600 (3 527)All variants with manual

75 (165)All variantsMaximum trailer nose weight

3 920 (8 642)2.0L petrol with automatic

3 900 (8 598)2.0L diesel with automatic

3 935 (8 675)2.0L diesel with manual

Note: For every 1 000 metres increase above sea level, the GTW must be reduced by 10%.

Towing

TOW BALL OPTIONS

The available Tow ball options for this vehicle are:

Quick release, detachable tow ball. See 91, FITTING THE DETACHABLE TOW BALL.

Electrically deployable, powered tow ball. See 92, POWERED TOW BALL.

Note: The tow ball options are dependent on the market and the vehicle specification.

The ability of TSA may be reduced when travelling on slippery surfaces.

Note: TSA will not operate when Dynamic Stability Control (DSC) is switched off.

HITCH GUIDANCE

Hitch guidance is a user selectable Touch screen feature that can aid the process of guiding the vehicle to a trailer's tow hitch. Use Hitch guidance while reversing the vehicle to a trailer hitch.

Proceed, as follows:

Select reverse gear. Dependent on the vehicle's specification, the Touch screen will automatically display selectable icons or a menu list. See 124, SURROUND

CAMERA SYSTEM or see 117, REAR CAMERA.

Touch the Rear camera system's Hitch assist icon, or for Surround camera's, tick Hitch guidance on the Touch screen to

enable the guidance lines to be displayed.

Reverse the vehicle towards the trailer.

As the vehicle closes to within 600 mm (2 ft) of the trailer's tow hitch, an automated zoom feature is operated to enlarge the view.

Continue the manoeuvre carefully until the vehicle and trailer are as close as required.

TRAILER STABILITY ASSIST (TSA)

When a trailer is attached, TSA will automatically detect when trailer sway is developing. It will then gradually reduce the vehicle's speed, by cutting engine power and applying the brakes to help regain control.

TSA will not operate in the event of the trailer jack-knifing.

Towing

TOW ASSIST

Note: Trailer guidance requires a connected trailer to be fitted with a tracking target sticker, which must be attached according to specific instructions. Ask a Dealer/Authorised Repairer for details.

Note: This feature may not operate with all trailer designs.

Trailer guidance aids trailer reversing, by displaying guidance lines on the Touch screen.

Trailer guidance becomes active when a trailer/caravan is attached to the vehicle and the trailer's electrical plug is attached to the vehicle's socket.

Note: The driver's door must be opened and closed after the trailer/caravan is connected to the electrical socket, before the system will detect the connection.

The screen will display a choice for connection. Select YES to move to the setup screen. Select NO to return to the previous screen.

Note: If the connection is not detected, setup can be manually prompted by touching the Tow assist soft key on the Camera menu.

On first use, the setup screens take the user through a series of configuration options for the connected trailer. Information such as trailer hitch length, number of axles, and camera preference, is required to finalise setup. Once completed, the details are stored for future use.

When a new or existing trailer configuration is selected, Trailer guidance automatically displays on the Touch screen when reverse gear is selected. Coloured lines are displayed to indicate the predicted path of both the trailer and the vehicle.

FITTING THE DETACHABLE TOW BALL

Towing

Fit the Detachable tow ball as follows:

Remove the protective cover from the vehicle mounting and stow it in the tow ball stowage area.

The tow ball can only be installed when the locking lever is in the unlocked position (red showing).

Insert the tow ball into the tow bar mounting and push firmly upwards until the tow ball locks into position.

Turn the locking lever towards you until green is showing.

Remove the protective cover from the key slot.

Insert the key and turn it clockwise to lock the tow ball, then remove the key and refit the protective cover. Store the key in a safe place.

Do not exceed the maximum nose weight for the detachable tow ball. See 88, TOWING WEIGHTS.

When the detachable tow ball is not required for immediate use, it should be removed from the tow bar and stowed in the appropriate place.

Towing

REMOVING THE DETACHABLE TOW BALL

Remove the Detachable tow ball as follows:

Insert the key and turn it counter-clockwise to unlock.

Remove the key, then supporting the tow ball, press and turn the locking lever away from you to release.

Remove the tow ball from the tow bar and stow it in the luggage compartment stowage area, in the bag provided.

POWERED TOW BALL

Before activating the powered tow ball, make sure that:

• Any trailer is unhitched.

• Any trailer electrical connections are disconnected.

• The vehicle is stationary.

• The luggage compartment lid is open.

• The vehicle's transmission is engaged in Park (P) or neutral.

Failure to comply with the above conditions will prevent the powered tow ball from operating. Also a short warning tone will sound if the powered tow ball button is pressed.

Note: If the powered tow ball does not function correctly, refer to a Dealer/Authorised Repairer.

Powered tow ball button: Press and release to deploy the powered tow ball. Press and release again to stow the powered tow ball.

• The LED indicator lamp, by the side of the button, will flash slowly while the powered tow ball is being deployed or stowed. An audible tone will also sound.

• Once deployed, the LED indicator lamp will stop flashing and will be solidly lit.

• Once stowed, the LED indicator lamp will stop flashing and will be solidly lit for 2 seconds and will then extinguish.

• To stop movement of the powered tow ball, press the tow ball button. To reset the tow ball, press the tow ball button again. During the reset operation, the powered tow ball will fully stow and then fully deploy.

Towing

• If, during deployment of the powered tow ball, an obstruction occurs, tow ball movement will stop. The LED indicator lamp will flash faster, accompanied by a 2 second warning tone. When the obstruction has been cleared, press the tow ball button to reset the tow ball.

• If the vehicle is driven with the tow ball neither fully deployed or fully stowed, a warning tone will sound for 10 seconds. Do not tow with the tow ball in this state.

• In the event of unexpected operation, press the tow ball button to reset the tow ball.

Make sure the powered tow ball is fully deployed before connecting a trailer/caravan.

Trailer lamp test button: Press to start a 3 minute sequence for both the vehicle and the trailer's lamp testing.

• For the test to operate, all of the vehicle's lamps should be switched off, the ignition should be switched off and the transmission should be in Park (P) or neutral.

• The vehicle's lamps and all of the trailer's lamps will operate at the same time so that a visual check can be made of all the lamps.

• The 3 minute sequence can be stopped, at any time, by pressing the trailer lamp test button again, by manually switching on the vehicle's lamps, or by switching on the ignition.

Note: This test feature only allows an observer to check that the lamps are illuminating. The car does not perform any measurements during this test and faulty trailer lamps will not show any errors during this test.

TRAILER ELECTRICAL CONNECTION

Attach only approved electrical connectors, which are in good condition, to the trailer socket.

The detachable tow ball, trailer socket should be manually deployed (2) and stowed (1), as illustrated.

The electric deployable tow ball, trailer socket will deploy and stow automatically with the tow ball.

When a trailer's electrical connection is made and the vehicle’s direction indicators are used, the trailer warning indicator will flash in time with the direction indicators. See 55, TRAILER DIRECTION INDICATORS (GREEN).

Towing

In the event that the vehicle's direction indicator is used and the symbol does not flash, the trailer's connection should be checked and appropriate action taken to make sure that the trailer's direction indicators are functioning.

Function

Brake lamps

Direction indicators*

markers/rear lamps*

battery feed

* For each side.

Minimum load

0.25 amps (6 Watt)

-Side

-Reverse lamps

-Fog lamp

-Permanent

-Ignition feed

Maximum load amps (Watt)

10 amps (120 Watt)

5 amps (60 Watt)*

5 amps (60 Watt)

15 amps (180 Watt)

• To maintain vehicle stability, the trailer's nose load should be set at approximately 7% of the caravan/trailer's gross weight (and a minimum of 4%).

• When towing a trailer with more than one axle, the trailer should be loaded to achieve even weight distribution between axles.

• When calculating the laden weight of the trailer, remember to include the weight of the trailer, plus the weight of the load.

• If the load can be divided between the vehicle and trailer, loading more weight into the vehicle will generally improve stability. Do not exceed the vehicle's weight limits.

• Increase the rear tyre pressures on the towing vehicle to those for maximum vehicle loading conditions.

• Make sure that a suitable breakaway cable, safety chain, or secondary coupling is used. Refer to the trailer manufacturer's instructions for guidance.

• Always connect the breakaway cable or safety chain to the provided connection point. Do not loop it over the tow ball.

• Make sure that the tow ball is secure.

• Check the operation of all the lamps on the trailer.

ESSENTIAL TOWING CHECKS

Do not exceed the Gross Vehicle Weight (GVW), maximum rear axle weight, maximum trailer weight, or nose weight. Exceeding any of these limits could cause instability and a loss of control.

Do not loop the breakaway cable or safety chain over the tow ball, as it may slide off.

TOWING A TRAILER

Never exceed the maximum weights for either the vehicle, or the trailer. Doing so can cause accelerated wear and damage to the vehicle. It can also adversely affect vehicle stability and braking, which in turn can lead to a loss of control and an increased braking distance, resulting in a rollover or crash.

Towing

To preserve handling and stability, only fit Jaguar approved towing accessories.

Never use towing eyes or lashing points to tow a trailer. They have not been designed for this purpose and doing so may cause them to fail, resulting in injury or death.

Note: A reduction in the performance of the Air conditioning system is a normal function under high load towing conditions.

Note: Engine power output always reduces with increased altitude. At 1000 metres above sea level and for every additional 1000 metres, deduct 10% from the Gross Train Weight (GTW). See 88, TOWING WEIGHTS.

The Touch screen can display a rear view to assist with the reversing of the vehicle with a trailer attached. See 124, SURROUND CAMERA

SYSTEM and also 90, TOW ASSIST.

TOW BALL MOUNTED ACCESSORIES

Before fitting a tow ball mounted accessory, make sure it has been approved for use on Jaguar vehicles.

The use of unsuitable equipment can result in severe damage to the tow ball and the tow bar.

Before fitting an accessory to the tow ball, observe the following guidelines:

The attached accessory must not protrude more than 700 mm (27.5 ins) from the tow ball.

The centre of gravity of the mounted equipment and load combined should not exceed a distance of 390 mm (15 ins) from the tow ball. The maximum weight at this distance must not exceed 82.4 kg (182 lb).

Note: The forces exerted by the trailer's nose load and tow ball mounted accessories are different in nature and; therefore, a separate limit applies to both.

Note: Only use a Jaguar approved bicycle rack, catering for a maximum of up to 2 bicycles.

Towing

TOW BAR DIMENSIONS AND MOUNTING POINTS

Detachable tow bar

Note: Dimensions refer to towing equipment

officially released by Jaguar.

Towing

InchesMillimetresDimension

215341

215342

16.94303

16.94304

16.74255

16.74256

215347

215348

4.51149

4.210610

1.94711

10.827512

42.51 08013

Towing

Deployable tow bar

Note: Dimensions refer to towing equipment

officially released by Jaguar.

Towing

InchesMillimetresDimension

215341

215342

16.94303

16.94304

16.74255

16.74256

215347

215348

4.51149

4.210610

1.94711

10.827512

42.51 08013

Starting the engine

STARTING THE ENGINE

Never start the engine, or leave it running, when the vehicle is in an enclosed space. Exhaust gases are poisonous and can cause unconsciousness and death if inhaled.

If the engine fails to start, do not continue cranking as this will discharge the battery. It may also damage the catalytic converter due to unburnt fuel passing through the exhaust.

Note: The Smart key may not be detected if it is placed within a metal container, or if it is shielded by a device with a back-lit LCD screen, such as a smart phone, laptop (including when inside a laptop bag), games console, etc. Keep the Smart key clear of such devices when attempting Keyless entry or Keyless start backup.

To start the engine:

Make sure a valid Smart key is inside the vehicle.

Make sure Park (P) or Neutral (N) is selected.

Automatic transmission: Press the brake pedal firmly. Manual transmission: Press the clutch pedal firmly.

Press and release the engine START/STOP button. See 288, DRIVER CONTROLS.

Note: For vehicles with a diesel engine, the delay period before cranking begins will be longer in low ambient temperatures due to extended glow plug operation. During this extended delay, the brake pedal must remain pressed.

Once the engine has started, the brake pedal (or clutch pedal) can be released, if it is safe to do so.

SWITCHING OFF THE ENGINE

While the vehicle is stationary:

Make sure Park (P) is selected for vehicles with an automatic transmission or neutral for a manual transmission vehicle. Apply the Electric Parking Brake (EPB).

Press and release the engine START/STOP button.

While the vehicle is moving:

It is not advisable to switch off the engine while the vehicle is moving. However, if a situation arises where engine switch off is urgent, the following procedure applies:

Press and hold the engine START/STOP button for longer than 2 seconds, or

Press and release the engine START/STOP button twice within 3 seconds. With either method, Engine Stop Button Pressed is displayed in the Message centre.

SWITCHING ON THE IGNITION

To switch on the ignition without starting the engine:

With a valid Smart key inside the vehicle:

• Vehicles with an automatic

transmission, make sure that the brake pedal is NOT pressed.

If the brake pedal is applied when the engine START/STOP button is pressed, the engine will start.

• Vehicles with a manual transmission,

make sure that the clutch pedal is NOT pressed.

If the clutch pedal is applied when the engine START/STOP button is pressed, the engine will start.

100

Jaguar Jaguar XE (2015) Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Entering the vehicle

Exiting the vehicle

Front seats

Rear seats

Head restraints

Steering wheel

Seat belts

Child safety

Airbags

Instrument panel

Warning lamps

Exterior lights

Interior lights

Wipers and washers

Mirrors

Blind spot monitoring

Garage door opener

Windows

Touch screen

Heating and ventilation

STORAGE COMPARTMENTS

Luggage compartment

Towing

Starting the engine