OPERATING MANUAL
Pure Air®
Whirlpool
Salon® Spa
Jacuzzi Luxury Bath
14525 Monte Vista Avenue
Chino, CA 91710 1-800-288-4002 www.jacuzzi.com
LG74000D |
06/2019 |
English |
Operating Manual |
|
Table of Contents |
General Operation Information......................................................................................................................................... |
2 |
Reference Illustration for a Pure Air® System.................................................................................................................. |
3 |
Pure Air® Operations........................................................................................................................................................ |
4 |
Pure Air® Auto-Dri™ Air Channels................................................................................................................................... |
5 |
Whirlpool System Reference Illustrations..................................................................................................................... |
6-7 |
Whirlpool Operations..................................................................................................................................................... |
8-9 |
Heated Soak Reference Illustrations......................................................................................................................... |
10-11 |
RapidHeat™................................................................................................................................................................... |
12 |
Cleaning......................................................................................................................................................................... |
13 |
Maintenance.............................................................................................................................................................. |
13-14 |
Salon® Spa System Reference Illustrations................................................................................................................... |
15 |
Salon® Spa Operations.................................................................................................................................................. |
16 |
Troubleshooting Procedures.......................................................................................................................................... |
17 |
*For Spanish and French installation instructions, please visit www.jacuzzi.com/baths/support/owners-manuals/. *Para instrucciones de instalación en español, por favor visite www.jacuzzi.com/baths/support/owners-manuals/. *Pour directives d'installation en français canadien, veuillez visiter www.jacuzzi.com/baths/support/owners-manuals/.
All bathtubs manufactured by Jacuzzi Luxury Bath are designed for “fill and drain,” which means the bathtub should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these bathtubs are not designed to hold water continuously like pools or spas.
Close the drain and fill the bathtub until water is at least 1" to 2" (25 mm to 51 mm) above the highest jet or air inlet (see water line indicated in the illustration - Figure 1). Do not turn on the Whirlpool or Pure Air® system at any time if the jets or air inlets are not completely immersed in water. Running the Whirlpool or Pure Air® system when there is insufficient water in the bathtub could result in water spraying outside the bath area.
ATTENTION: When exiting the bathtub, the water level will drop below the jets which could result in water being sprayed out of the unit. To prevent this, you must turn unit OFF before exiting bathtub.
Fig. 1
Fill to at least 1" to 2" above highest jet
Page 2 |
www.jacuzzi.com |
Operating Manual |
English |
These illustrations are for reference only, as the unit comes fully assembled.
DANGER: RISK OF ELECTRIC SHOCK! Before servicing these connections, disconnect all power supply cables to both 120 VAC services.
J2 Control Panel Pure Air® Schematic Diagram
Fig. 2
120 VAC 15A
Dedicated GFCI
Circuit Required
CONTROL
PANEL
BLOWER |
J4 Control Panel Pure Air® Schematic Diagram
120VAC 15A Fig. 3 Dedicated GFCI
Circuit Required
120VAC 15A |
CONTROL PANEL |
Dedicated GFCI |
|
Circuit Required |
LIGHT CONTROL |
|
|
|
BOX |
|
120 VAC |
Auto-Dri™ |
Panel LED Light |
SENSOR |
BLOWER |
CABLE |
CHROMATHERAPY
LIGHTS 2X
www.jacuzzi.com |
Page 3 |
English |
Operating Manual |
Pure Air® Operations
J2 Pure Air® Controls
Fig. 4
BLOWER OPERATION
•Press once to turn ON
•Press again to turn OFF
NOTE: The last blower setting used is remembered by the system and will automatically resume upon next use.
J4 Pure Air® Controls
INCREASE TOGGLE
•Press to increase the blower intensity
•Press and hold 5 seconds to set/ cancel daily Auto-Dri™
•Alternately, you can press and hold the button to increase the intensity level.
DECREASE TOGGLE
•Press to decrease the blower intensity
•Alternately, you can press and hold the button to decrease the intensity level
Fig. 5
BLOWER OPERATION
• Press to turn ON
• Press again to turn OFF
• Use toggles to control speed
CHROMATHERAPY
• Press once to turn lights ON at white level 2
•Press again to cycle colors
•Press again to stop at the current color
•Press again to restart the cycle
•Color Sequence: White, Purple, Blue, Turquoise, Green, Yellow, Orange, Red, Pink, Repeat
INCREASE TOGGLE
•Press to increase selected feature
•Press and hold 5 seconds to set/cancel daily Auto-Dri™
•Press to increase light intensity
•Press to turn ON lights at last color used from OFF
PULSE FEATURE
•Press to turn Pulse ON
•Press to turn Pulse OFF
•+/- keys can be used to adjust maximum air intensity
STATUS LED
•Relays the current intensity of selected feature
NOTE: When switching between functions, the LED for the newly selected function will FLASH once to indicate selection.
DECREASE TOGGLE
•Press to decrease selected feature
•Press to decrease light intensity all the way down to OFF
WAVE FEATURE
• Press to turn Wave ON
•Press to turn Wave OFF
•+/- keys can be used to adjust maximum intensity
Low |
Medium |
Medium |
High |
1-2 |
Low 3-4 |
High 5-6 |
7-8 |
Page 4 |
www.jacuzzi.com |
Operating Manual |
English |
J2 Auto-Dri™ Air Channels
The blower will operate for 20 minutes and then automatically shut off, unless power is manually turned off. In either case, 20 minutes after the blower has shut off, it will turn ON for a one-minute drying cycle to blow out any water remaining in the air system.
If the bath is used without the blower operating (showering or bathing without using the Pure Air® system), initiate the oneminute drying cycle manually by use of the ON/OFF switch. Turn the switch ON and OFF again as you exit the bath and the drying cycle will occur in 20 minutes.
J2 Daily Auto-Dri™ Cycle
To Activate: Holding the button for five-seconds when the blower is off activates the daily Auto-Dri™ cycle. The blower will start every day at the same time for one-minute. Once the daily Auto-Dri™ cycle is activated, the blower will come on for one-second, turn off for two-seconds, come on for one-second and then turn off.
To Deactivate: Holding the button for five-seconds when the blower is off deactivates the daily Auto-Dri™ cycle. When the daily Auto-Dri™ cycle is deactivated, the blower will come on for one-second and then turn off.
J4 Auto-Dri™ Air Channels
The Auto-Dri™cycle is automatic and will reduce excessive accumulation of residual water in the air channels.
There are two Auto-Dri™ cycles: drain assisted Auto-Dri™ cycle and daily Auto-Dri™ cycle.
J4 Drain Assist
The Auto-Dri™ cycle is sensor assisted – two sensors (metal dials) are located near the drain of the bathtub. The sensors detect the presence and absence of water in the bathtub.
To ensure effective and correct operation of the water sensors, it is important to keep them clean and free from blockage or objects.
After bathing and following the emptying of the bathing well, the sensors detect a “no water” condition. A five minute wait time elapses and then the blower is activated. The blower will cycle through a range of speeds for 2 ½ minutes, during which either 2 or 3 indicator lights will flash at various speeds.
•The Auto-Dri™ cycle will engage even if the blower is not used during bathing.
•The cycle may initiate more than once if the sensors become wet during any part of the Auto-Dri™ operation or during routine cleaning of the bathtub. This is normal and does not require attention.
•
•
J4 Daily Auto-Dri™ Cycle
Each day, the blower will automatically activate a daily Auto-Dri™ cycle. The blower will operate for one minute on high power, followed by 15 seconds at ½ power.
To set Auto-Dri™ cycle time: Wait until the time that you desire the daily Auto-Dri™ cycle to activate. With the blower off, press and hold the plus button for five seconds. To confirm that you have set the time, the blower will cycle between on and off two times in a 4 second span.
To cancel daily Auto-Dri™ cycle: With the blower off, press and hold the plus button for five seconds. To confirm that you have cancelled the Auto-Dri™ cycle , the blower will come on for 1 second and then stop.
You must set the daily Auto-Dri™ cycle upon installation; the default is no pre-set daily Auto-Dri™ cycle. If a power failure occurs, the system will default to no daily Auto-Dri™ cycle.
www.jacuzzi.com |
Page 5 |
English |
Operating Manual |
Whirlpool System Reference Illustrations
Pushbutton Whirlpool Schematic Diagram
Fig. 6
J2 Control Panel Whirlpool Schematic Diagram
Fig. 7
120VAC 15A Dedicated GFCI Circuit Required
120VAC 20A Dedicated GFCI Circuit Required
CONTROL PANEL |
PUMP/MOTOR |
CONTROL BOX |
120 VAC |
||
|
|
|
|
|
|
|
|
PUMP
PUMP
FOR MODELS
WITH IN-LINE
HEATER
OR |
PUMP/MOTOR
Page 6 |
www.jacuzzi.com |
Operating Manual |
English |
Whirlpool System Reference Illustrations (Continued)
J2 Control Panel Whirlpool with Chromatherapy Schematic Diagram
Fig. 8 |
PUMP/MOTOR |
|
CONTROL PANEL |
120V 20A |
|
Decidated GFCI |
|
Circuit Breaker |
|
CONTROL BOX |
|
120VAC |
|
PUMP |
120V 15A |
CHROMATHERAPY |
Decidated GFCI |
LIGHTS |
Circuit Breaker |
|
FOR MODELS
WITH IN-LINE
HEATER
J4 Control Panel Whirlpool Schematic Diagram
Fig. 9
PUMP/MOTOR |
LEAD CONNECTIONS |
|
SEE VIEW A
4-WHITE-C
3-BLACK-H
|
OR |
2-N/A |
AIR VALVE |
VIEW A 1-GREEN-GRD |
|
|
|
|
ASSEMBLY |
PUMP/MOTOR |
|
|
|
120VAC 15A |
CONTROL PANEL |
|
Dedicated GFCI |
CONTROL BOX |
|
Circuit Required |
||
|
Air Valve |
120VAC Pump |
|
Blower LED Light |
SEE VIEW B
|
LEAD CONNECTIONS |
|
|
4-WHITE-C |
|
|
3-BLACK-H |
|
VIEW B |
2-RED-L |
|
1-GREEN-GRD |
||
|
|
|
Panel |
120VAC 20A |
|
|
|
|
||
FOR MODELS |
|
|
Dedicated GFCI |
|
|
|
Circuit Required |
||
WITH IN-LINE |
CHROMATHERAPY |
OR |
ILLUMATHERAPY |
|
HEATER |
||||
LIGHTS 2X |
|
LIGHTS 4X |
||
|
|
www.jacuzzi.com |
Page 7 |
English |
Operating Manual |
Whirlpool Operations
Pushbutton Whirlpool Controls
Fig. 10A
Push down on the button to |
|
|
turn ON the whirlpool system. |
|
|
Push down on the button to |
ON/OFF Button |
|
turn OFF the whirlpool system. |
||
|
J2 Whirlpool Controls
Fig. 11
Whirlpool Control
Fig. 10B
In the closed position, the jets massage with only water.
In the open position, air mixes with water to create a
deep, wide plume of |
OPEN Position |
CLOSED Position |
massaging bubbles. |
|
|
• Press once to turn ON.
• Press again to turn OFF.
J2 Whirlpool Controls with Chromatherapy Controls |
|
Fig. 12 |
• Press once to turn ON. |
|
• Press again to turn OFF. |
CHROMATHERAPY
•Press once to turn lights ON at white level 2
•Press again to cycle colors
•Press again to stop at the current color
•Press again to restart the cycle
•Color Sequence: White, Purple, Blue, Turquoise, Green, Yellow, Orange, Red, Pink, Repeat
INCREASE TOGGLE
•Press to increase light intensity
•Press to turn ON lights at last color used from OFF
NOTE: Default lighting color is white level 2.
DECREASE TOGGLE
•Press to decrease light intensity all the way down to OFF
NOTE: Default lighting color is white level 2.
Page 8 |
www.jacuzzi.com |
Operating Manual |
English |
Whirlpool Operations (Continued)
J4 Whirlpool Controls
Fig. 13
NOTE: When switching between functions, the LED for the newly selected function will FLASH once to indicate selection.
WHIRLPOOL |
INCREASE TOGGLE |
DECREASE TOGGLE |
|
• Press to turn ON |
• Press to increase selected |
• Press to decrease the |
|
• Press again to turn OFF |
feature |
selected feature |
|
• Use toggles to control |
• Press to increase light inten- |
• Press to decrease light |
|
|
speed* |
sity |
intensity all the way |
* Whirlpool speed available |
• Press to turn ON lights at last |
down to OFF |
|
color used from OFF |
|
||
|
only for models equipped |
|
|
|
with 2-speed motors. |
|
|
LEFT AIR VALVE CONTROL |
RIGHT AIR VALVE CONTROL |
WAVE FEATURE |
|
• |
Press to activate the left air |
• Press to activate the right air |
• Press to turn Wave ON |
|
valve |
valve |
• Press to turn Wave OFF |
• Use toggles to control air |
• Use toggles to control air mix |
• +/- keys can be used to |
|
|
mix |
|
adjust maximum intensity |
CHROMATHERAPY |
STATUS LED |
|
|
• Press once to turn lights |
• Relays the current intensity of |
|
|
|
ON at white level 2 |
selected feature |
|
• Press again to cycle |
|
|
|
|
colors |
|
|
• Press again to stop at the |
|
|
|
|
current color |
|
|
• Press again to restart the |
|
|
|
|
cycle |
|
|
• |
Color Sequence: White, |
|
|
|
Purple, Blue, Turquoise, |
|
|
|
Green, Yellow, Orange, |
|
|
|
Red, Pink, Repeat |
|
|
www.jacuzzi.com |
Page 9 |
English |
Operating Manual |
Heated Soak System Reference Illustrations
J2 Control Panel Heated Soak Schematic Diagram
Fig. 14
120VAC 15A GFCI
CONTROL PANEL
PUMP/MOTOR
CONTROL BOX
120 VAC
Pump
J2 Control Panel Heated Soak with Chromatherapy Schematic Diagram
Fig. 15
120VAC 15A GFCI
PUMP/MOTOR
CONTROL PANEL |
CONTROL BOX |
|
|
|
Pump 120 VAC |
|
Panel LED Light |
CHROMATHERAPY
LIGHT
Page 10 |
www.jacuzzi.com |
Operating Manual |
English |
Heated Soak System Reference Illustrations (Continued)
J2 Heated Soak Controls
Fig. 16
• Press once to turn ON.
• Press again to turn OFF.
J2 Heated Soak with Chromatherapy Controls
Fig. 17
• Press once to turn ON.
• Press again to turn OFF.
CHROMATHERAPY
•Press once to turn lights ON at white level 2
•Press again to cycle colors
•Press again to stop at the current color
•Press again to restart the cycle
•Color Sequence: White, Purple, Blue, Turquoise, Green, Yellow, Orange, Red, Pink, Repeat
INCREASE TOGGLE
•Press to increase light intensity
•Press to turn ON lights at last color used from OFF
NOTE: Default lighting color is white level 2.
DECREASE TOGGLE
•Press to decrease light intensity all the way down to OFF
NOTE: Default lighting color is white level 2.
www.jacuzzi.com |
Page 11 |
English |
Operating Manual |
Whirlpool Operations (Continued)
Controlling Whirlpool Direction & Flow
CAUTION: Never run the whirlpool system with all the jets closed.
To adjust the direction of the jets:
•To change the direction of the water flow, swivel the jet nozzle to the desired angle (Figure 18).
To adjust the water flow to the jets:
•Increase the force of the flow by rotating the nozzle or jet face to the left (counterclockwise). Decrease the force of the flow by rotating the nozzle or jet face to the right (clockwise). Reference Figure 19.
Fig. 18 |
Fig. 19 |
Controlling Waterfall (Applicable Models Only)
The waterfall can only be activated when the whirlpool pump is in operation.
The more the waterfall control knob is turned in a counterclockwise direction, the flow of water will increase. Reference
Figure 20.
Turning ON... |
Turning OFF... |
Fig. 20
Turning the Waterfall Control knob |
Turning the Waterfall Control knob |
counter-clockwise will turn on the waterfall |
clockwise will turn off the waterfall |
To remove accumulations of bathtub residue from the system, it is recommended that a bathtub be cleaned at least twice a month. For best results, however, we recommend that you clean your bathtub after each use using Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for bathtubs. Systems Clean™ is available through an authorized Jacuzzi Luxury Bath distributor, by calling 1-800-288-4002 or may be purchased online at www.jacuzzi.com.
RapidHeat™ (Standard on Salon® Spa Models)
The heater turns ON automatically any time whirlpool operation is active. Heater operation is not displayed on the control panel. There is a visible indicator light on the heater itself that signifies the heater is operating (Figure 21). The heater will help maintain the temperature of the water in the bathtub. It is not intended to heat the water to a desired temperature.
Vacuum Switch |
Fig. 21 |
|
|
The heater is equipped with a preset vacuum switch which will not allow |
PROTECTION |
|
OVER HEAT |
the heater to turn ON if the pump is not running and water is not flowing |
|
through the whirlpool system. |
PUSH TO RESET |
High-Limit Switch |
|
IMPORTANT NOTE:
Heater will only work when the water temp is 77°F or above. You should always fill the tub with warm water.
|
High Limit |
|
|
Heater |
|
Reset |
|
|
On |
|
|
|
||
|
|
|
|
|
|
|
HEATER ON |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The heater includes an exclusive High-Limit switch (Figure 21). This safety circuit will not false trip from hot tap water. It will only turn OFF the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, please contact us at www.jacuzzi.com, or at 1-800-288-4002.
Page 12 |
www.jacuzzi.com |
Operating Manual |
English |
Systems Clean™
To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a Whirlpool bathtub be cleaned at least twice a month. For best results, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for Whirlpool bathtubs. Systems Clean™ is available through an authorized Jacuzzi Luxury Bath distributor by calling us direct at 1-800-288-4002, or may be purchased online at www.jacuzzi.com/baths.
Bathtub Additives
CAUTION: Do not use oil or oil-based bathtub additives. Never use abrasive or caustic household cleaners on any
Jacuzzi Luxury Bath product.
If you want to use any kind of bathtub additive, use only a small amount of low-foaming powder or crystal substance; the whirlpool action intensifies the foaming properties of soaps.
The use of certain bathtub oils, bubble baths, and bathtub additives may increase the level of accumulations of bathtub residue in the Whirlpool system and may cause false reading of the water level sensors. If excess accumulations persist, you should discontinue use of these products.
To remove accumulations of bathtub residue from the Whirlpool system, it is recommended that a bathtub be cleaned regularly. For best results, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for Whirlpool bathtubs. Systems Clean™ is available through an authorized Jacuzzi Luxury Bath distributor, or by calling 1-800-288-4002 or may be purchased online at www.jacuzzi.com.
To clean your bathtub, simply use a mild, non-abrasive liquid detergent solution. You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar’s #10 Mirror Glaze, a product specifically designed for use on acrylic finishes. If Meguiar’s is not available, use a fine grade automotive rubbing compound followed by an application of clear automotive paste wax.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper. Restore the gloss using Meguiar’s Mirror Glaze or automotive paste wax. Major scratches and gouges which penetrate the acrylic surface will require refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area.
Maintenance
Spinning Jet Maintenance |
|
If hair, or other types of debris, get caught in the bearings of these jets, it could cause |
Fig. 22 |
them to stop spinning (Figure 22). This may require disassembly and removal. To do this, |
|
simply grab the nozzle and pull it straight out of the jet housing. The bearing casing will be |
|
attached to the nozzle. These two items can be separated by holding the casing and push- |
|
ing the nozzle out from the rear of the casing. After the cleaning is complete, reassemble |
|
and reinstall. |
|
www.jacuzzi.com |
Page 13 |
English |
Operating Manual |
Maintenance (Continued) |
|
Whirlpool Suction Cover/Strainer Maintenance |
|
Clean the suction cover/strainer of hair and debris when necessary (Figure 23). |
Fig. 23 |
1.Remove the center screw and detach the suction cover.
2.Clean the cover by back flushing debris from the holes.
3.Replace the suction cover immediately after cleaning.
WARNING! When reinstalling, orient the cover/strainer with the small notch at the bottom. The gasket must be inserted into the groove of the cover/strainer before reinstalling onto the suction fitting.
DANGER: RISK OF SEVERE INJURY OR DROWNING! Keep hair a
minimum of 6 inches (152 mm) away from the suction fitting at all times when the whirlpool system is operating. Hair longer than shoulder length should be secured close to the head, or a bathing cap should be worn.
DANGER: RISK OF SEVERE INJURY OR DROWNING! Do not operate the Whirlpool system with the suction cover/strainer removed! It is a safety device and must always be in place on the suction fitting to minimize the potential hazard of hair and body entrapment.
Page 14 |
www.jacuzzi.com |
Operating Manual |
English |
Salon® Spa System Reference Illustrations
J4 Control Panel Salon® Spa Schematic Diagram
Fig. 24
240VAC/20A |
|
|
PUMP/MOTOR |
|
Dedicated GFCI |
|
|
|
|
Required |
|
|
|
|
|
|
AIR VALVE |
|
|
|
|
ASSEMBLY |
|
|
|
|
|
ILLUMATHERAPY |
|
|
|
|
LIGHTS 4 |
|
|
|
CONTROL |
|
|
FUSE/JUNCTION |
|
PANEL |
|
OR |
|
|
|
||
|
CONTROL BOX |
|
||
BOX |
|
|
||
|
Air Valve |
|
|
|
|
|
240VAC |
Pump |
|
FUSE |
FUSE |
|
||
|
|
|
Blower LED Light |
|
FUSE |
|
FUSE |
|
|
|
|
Panel |
|
|
HEATER
AUTO-DRI™
SENSOR CABLES
LEAD CONNECTIONS
4-WHITE-C
3-BLACK-H
2-N/A 1-GREEN-GRD
VIEW A
SEE VIEW A
CHROMATHERAPY |
120VAC 15A |
|
LIGHTS 2X |
||
Dedicated GFCI |
||
|
||
|
Required |
BLOWER |
J5 Control Panel Salon® Spa Schematic Diagram
Fig. 25
240VAC/20A |
|
|
|
Dedicated GFCI |
PUMP/MOTOR |
|
|
Required |
|
|
|
AIR VALVE |
|
SEE VIEW A |
|
ASSEMBLY |
|
|
LEAD CONNECTIONS |
|
|
|
4-GREEN-(GRD) |
|
|
4 |
3-RED-(L) |
|
|
2 |
2-BLACK-(H) |
|
|
3 |
|
|
|
1 |
1-WHITE-(C) |
CONTROL |
TEMPERATURE |
VIEW A |
|
PANEL |
SENSOR |
|
|
FUSE/ |
CONTROL BOX |
|
|
|
|
|||
JUNCTION BOX |
Air Valve |
|
Light 1 |
Light |
Light 1 Sensor |
240VAC |
Pump |
120VAC 15A |
|
RS232 |
Inside |
Inside |
Ambient Temp |
|
|
|
|
|
|
|
2 |
4 |
2 |
|
|
Dedicated GFCI |
|
|
|
Inside |
Inside3 |
Ambient LOGO |
|
|
|
|
|
Panel Blower Light |
Light |
Light Light |
|
|
|
|
|
|
|
|
|
|
|
|
Required |
|
|
|
|
|
|
|
|
CHROMATHERAPY |
|
|
|
|
|
|
|
|
LIGHTS 2X |
|
|
ILLUMATHERAPY |
OR |
BLOWER |
||||
|
|
|
||||||
|
|
|
|
|||||
HEATER |
|
LIGHTS 4X |
|
|
|
|||
|
AUTO-DRI™ SENSOR CABLES |
|
||||||
|
|
|
www.jacuzzi.com |
|
Page 15 |
English
Salon® Spa Operations
J4 Salon® Spa Controls
Fig. 26
WHIRLPOOL |
INCREASE TOGGLE |
• Press to turn ON |
• Press to increase selected |
• Press again to turn OFF |
feature |
• Use toggles to control |
• Press and hold 5 seconds to |
speed |
set/cancel daily Auto-Dri™ |
|
• Press to increase light inten- |
|
sity |
|
• Press to turn ON lights at last |
|
color used from OFF |
Operating Manual
NOTE: When switching between functions, the LED for the newly selected function will FLASH once to indicate selection.
DECREASE TOGGLE
• Press to decrease the selected feature
• Press to decrease light intensity all the way down to OFF
LEFT AIR VALVE CONTROL |
RIGHT AIR VALVE CONTROL |
WAVE FEATURE |
|
• |
Press to activate the left air |
• Press to activate the right air |
• Press to turn Wave ON |
|
valve |
valve |
• Press to turn Wave OFF |
• Use toggles to control air |
• Use toggles to control air mix |
• +/- keys can be used to |
|
|
mix |
|
adjust maximum inten- |
|
|
|
sity. |
CHROMATHERAPY |
STATUS LED |
PURE AIR® FEATURE |
|
• Press once to turn lights |
• Relays the current intensity of |
• Press to turn ON |
|
|
ON at white level 2 |
selected feature |
• Press again to turn OFF |
• Press again to cycle |
|
• Use toggles to control |
|
|
colors |
|
intensity |
• Press again to stop at the |
|
|
|
|
current color |
|
|
• Press again to restart the |
|
|
|
• |
cycle |
|
|
Color Sequence: White, |
|
|
|
|
Purple, Blue, Turquoise, |
|
|
|
Green, Yellow, Orange, |
|
|
|
Red, Pink, Repeat |
|
|
Pure Air® and Auto-Dri™ Air Channels
For complete operating instructions reference page 5.
J5 Salon® Spa Controls
Main Menu |
POWER |
Optional J5 Luxury LCD Control Panel: Operation instructions for this panel are outlined in the supplemental guide provided in your warranty pack. Refer to this document for complete operation details (P/N GU47000).
J5 Control Panel
Controlling Whirlpool Direction and Flow
For complete operating instructions reference page 12.
Page 16 |
www.jacuzzi.com |
Operating Manual |
|
|
English |
|
|
Troubleshooting Procedures |
|
|
|
|
|
PROBLEM |
PROBABLE CAUSES |
REMEDY |
|
Pump/motor does not start |
• |
No power to pump/motor |
• Reset GFCI |
|
• Pump/motor not plugged in |
• Insert plug securely into outlet |
|
|
• |
Pump/motor faulty |
• Ensure control panel is connected to control box |
|
|
|
• Contact Jacuzzi Luxury Bath @ 800-288-4002 |
Pump/motor operates but no fully |
• |
Jets are closed |
• Open jets by rotating counter-clockwise |
adjustable jets are functioning |
• |
Suction cover/strainer may be clogged |
• With the motor turned OFF, remove the suction |
|
|
|
cover/strainer and remove any debris. Replace the |
|
|
|
suction cover before operating |
|
|
|
|
Pump/motor operates but air is not |
• |
Air valves are closed |
• Open air control valves |
injected into the water |
|
|
|
Water leakage from pump unions |
• |
Overtightened, O-ring may be pinched or improp- |
• Loosen unions, check and reseat O-ring. If O-ring |
|
|
erly seated, undertightened |
has been pinched out of shape, replace (refer to |
|
|
|
number below). When tightening union nuts, hand |
|
|
|
tighten only |
Pump/motor shuts off by itself before |
• |
Motor thermal protection has deactivated pump/ |
• Let motor cool; thermal protection will reset. Check |
time elapses |
|
motor due to overheating (supply voltage low) |
for proper ventilation (check supply voltage) |
|
• |
GFCI tripped |
• Reset GFCI; if it continues to trip, do not use this |
|
• |
Inadequate supply wiring |
unit. Disconnect the unit and have the problem cor- |
|
|
|
rected by a licensed electrician before using |
|
|
|
• Consult a licensed electrician to correct the wiring |
|
|
|
unit |
Chromatherapy lights do not operate |
• |
Connector has come loose |
• Contact Jacuzzi Luxury Bath @ 800-288-4002 |
|
|
|
|
Blower does not start |
• |
No power to pump/motor |
• Reset GFCI and/or breaker |
|
• |
Blower not connected |
• Ensure plug is fully in outlet |
|
• |
Blower faulty |
• Ensure control panel is connected to control box |
|
|
|
• Ensure control box is connected to control panel |
|
|
|
• Contact Jacuzzi Luxury Bath @ 800-288-4002 |
Blower operates but NO air is exiting |
• |
Check valves are stuck in the closed position |
• Contact Jacuzzi Luxury Bath @ 800-288-4002 |
the holes |
|
|
|
|
|
|
|
Blower operates but air is not exiting |
• |
Blower intensity is not sufficient |
• Increase the blower intensity. NOTE: The system is |
all of the holes |
• |
Obstructed air holes |
designed such that all air channels operate at the 4th |
|
|
|
blower setting. |
|
|
|
• Remove debris with a toothpick or tooth brush |
|
|
|
|
Blower shuts off unexpectedly |
• |
20 minute timer has elapsed |
• Turn on blower |
|
• |
GFCI tripped |
• Reset GFCI; if it continues to trip, do not use the unit |
|
• |
Inadequate supply wiring |
• Consult a licensed electrician to correct |
|
• |
Improper ventilation |
• Contact Jacuzzi Luxury Bath @ 800-288-4002 |
|
• Connector has come loose |
|
|
Drain assist Auto-Dri™ cycle comes |
• |
Water sensors detect multiple wet and dry condi- |
• If during a Auto-Dri™ cycle, water is coming in |
on multiple times |
|
tions |
contact with both sensors, the system is working as |
|
|
|
designed and will continue to Auto-Dri™ until excess |
|
|
|
water is expelled |
|
|
|
• Remove any washcloth or toy that may be covering |
|
|
|
the sensors |
Drain assist Auto-Dri™ does not |
• |
Water sensors not connected and not detecting |
• Contact Jacuzzi Luxury Bath @ 800-288-4002 |
come on 5 minutes after bathtub is |
|
water being drained out of the tub |
|
drained out completely |
• |
Faulty control box |
|
Water not maintaining temperature |
• |
High limit switch on heater has tripped |
• Press Reset button on heater |
|
|
|
|
Waterfall not working |
• |
Whirlpool function not on |
• Turn on whirlpool |
|
• Waterfall control knob is in the OFF position |
• Turn waterfall control knob counter-clockwise until |
|
|
• Debris in waterfall outlet |
water flow is at the desired flow |
|
|
|
|
• Use a thin, rigid and non-abrasive material (ie. credit |
|
|
|
card) and gently swipe back and forth until debris is |
|
|
|
cleared away from the waterfall opening |
If the unit is within the warranty period, contact Jacuzzi Luxury Bath Service Support at 1-800-288-4002 with your bath’s serial number before work is started. The serial number is located on the Specification/Serial Number
Plate.
www.jacuzzi.com |
Page 17 |