Jacuzzi j315, J - 335, J - 325, J-300, J-345 User Manual

4.7 (3)
Jacuzzi j315, J - 335, J - 325, J-300, J-345 User Manual

Standard Troubleshooting Approach

S.T.A. Manual

2004 Jacuzzi Premium

Protech LED Model Hot Tubs

(J-315, J-325, J-335, J-345)

The following symbol is placed throughout this manual for your protection. Always use extreme caution whenever performing repairs to electrical control system components of any kind!

Danger: Electrical Shock Hazard Exists!

High Voltage Present On Circuit Board. Use Extreme Caution While Servicing Circuit Board.

Table of Contents

 

Chapter

Page

1.0

Standard Troubleshooting Approach (S.T.A.) ...............................................................

5

1.1

Why A Standard Troubleshooting Approach? ....................................................................

5

1.2

How To Use The STA .........................................................................................................

5

1.3

Professional Customer Service ..........................................................................................

5

1.4

Responding To An Incoming Service Call ..........................................................................

5

1.5

Preparing Foe A Service Call .............................................................................................

8

1.6

Before Calling Technical Support .......................................................................................

9

1.7

Before Leaving The Customer ..........................................................................................

9

1.8

Satisfying The Customer ....................................................................................................

10

2.0

Electro Static Discharge (E.S.D.) ....................................................................................

11

2.1

ESD - What Is It? What Does It Do? ..................................................................................

11

2.2

Avoiding ESD Damage ......................................................................................................

11

2.3

What About Wrist Straps And Special Mats? .....................................................................

11

2.4

Must Wrist Straps And Mats Be Used When Replacing A Circuit Board? ..........................

11

3.0

Main System Specifi cations (J-345) ...............................................................................

12

3.1

Main System Specifi cations (J-335) ...................................................................................

14

3.2

Main System Specifi cations (J-325) ...................................................................................

16

3.3

Main System Specifi cations (J-315) ...................................................................................

18

4.0

Main Control Panel Functions ........................................................................................

20

4.1

Setting Filter Cycle Start Time ...........................................................................................

20

4.2

Programming Filter Cycles .................................................................................................

20

4.3

Aftermarket Ozone Facts ...................................................................................................

22

5.0

Additional Control Panel Functions ...............................................................................

22

5.1

Setting Water Temperature ................................................................................................

22

5.2

Selecting Jet Speeds .........................................................................................................

22

5.3

Underwater Light Operation ...............................................................................................

22

5.4

Lock/Unlock Control Panel .................................................................................................

22

5.5

Lock Out Mode ...................................................................................................................

23

5.6

Summer Logic ....................................................................................................................

23

6.0

Understanding Circuit Board Pin Assignments ............................................................

23

6.1

Circuit Board Jumpers .......................................................................................................

23

7.0

Troubleshooting Using The Control Panel ....................................................................

24

7.1

Control Panel Displays .......................................................................................................

24

7.2

Control Panel Default Display ............................................................................................

24

7.3

Control Panel Status And Error Messages ........................................................................

24

7.4

Testing Flow Switch ...........................................................................................................

26

8.0

Troubleshooting Without The Control Panel .................................................................

27

8.1

No Heat Or Not Enough Heat (Diagrams A-E) ...................................................................

27

8.2

Intermittent Heating ............................................................................................................

32

8.3

Nothing Works ....................................................................................................................

33

Chapter

Page

8.4

Hot Tub Doesn’t Come On For Filter Cycle .......................................................................

33

8.5

House Breaker Trips ..........................................................................................................

34

8.6

Hot Tub Light Will Not Come On ........................................................................................

38

8.7

No Jets ...............................................................................................................................

39

8.8

Weak Or Surging Jets ........................................................................................................

40

8.9

Pump Runs And Quits During Jet Mode ............................................................................

41

8.10

Circulation Pump Not Working ...........................................................................................

42

8.11

Troubleshooting A Thermal Pump Cutout ..........................................................................

43

8.12

Pump Hums And Will Not Start ..........................................................................................

43

8.13

Ozonator Not Working .......................................................................................................

44

A.

Appendix ...........................................................................................................................

45

A1.0

Checking Voltage To The Hot Tub .....................................................................................

46

A2.0

Checking Voltage To Components .....................................................................................

47

A3.0

Checking Current Consumption Of Components ...............................................................

47

A4.0

Testing The Flow Switch ....................................................................................................

48

A5.0

About Fuses .......................................................................................................................

48

A6.0

The Watchdog (----) ............................................................................................................

48

A7.0

Understanding Ozone ........................................................................................................

49

A8.0

Understanding pH ..............................................................................................................

49

A9.0

2004 J-315, J-325 Circuit Board Illustration (120 VAC / 3 or 4-Wire Connection) .............

50

A10.0

2004 J-335, J345 Circuit Board Illustration ( 240 VAC / 3-Wire Connection) .....................

51

A11.0

Load Box Connection Diagrams A-F ..................................................................................

52

A12.0

Temperature / Hi-Limit Sensor Resistance Chart ..............................................................

55

A13.0

Flow Switch Illustration ......................................................................................................

56

A14.0

Sensor Harness Connector Diagram .................................................................................

56

A15.0

Transformer Test ................................................................................................................

57

A16.0

Troubleshooting the Optional Stereo System ....................................................................

58

A17.0

Suggested Spare Parts ......................................................................................................

59

A18.0

Glossary Of Terms .............................................................................................................

60

A19.0

Sample Troubleshooting Data Collection Form .................................................................

61

1.0Standard Troubleshooting Approach (S.T.A.)

1.1Why A Standard Troubleshooting Approach?

Service prices are basically set by local industry and geographic region. Stiff competition in the service industry has made it diffi cult to raise the price of a service contract; or charge more for time and materials than the competetive shop down the street. If your business is to be profi table, you must control the overall cost of service. The total cost of service is made up of many individual factors, but three in particular are more important than the rest combined:

1.Time of Repair - How long it takes to fi nd and fi x a problem.

2.Time Between Failures - How often are you called to repair any one particular hot tub? How many times are you called back to fi x the same problem on the same hot tub?

3.Parts Usage - Except in rare circumstances, only one part fails. How many parts do you replace before you fi nd the bad one.

The Jacuzzi Premium STA Manual has been designed to help you control the overall cost of service by focusing on the three important aspects of your job outlined above. The STA will help you fi x your customer’s hot tub quickly, fi x it well, and use fewer parts.

1.2 How To Use The STA

The STA was developed by the Jacuzzi Premium Technical Support Department and is designed to be the communications link between you and your customers. If you call for help on any symptom covered in this book, you will be told to do what the STA recommends, there-

fore, you will save time by calling technical support after you have done what the STA tells you to do.

1.3 Professional Customer Service

Doing your job in a way that keeps cost of service low and profi t margin high also creates customer satisfaction. That’s being a professional!

1.4 Responding To An Incoming Service Call

Be

Prepared!

1.Phone personnel.

Which staff member(s) takes the initial call? This person is responsible for han- dling the call, writing up and making sure that the service technician receives all the information the same day.

2.Determine the customer complaint.

Determine whether this is a service call or a maintenance issue that can be handled over the phone.

Saving you (the technician) time and the company money should be a priority.

3.Verify the model number, serial number and confi rm that this is the original owner of the spa.

The original owner is the only one covered under the terms of the warranty.

Know what components are covered under the terms of the warranty, the length of time of the warranty and then confi rm that the owner understands what will and won’t be covered in the event of a service visit.

5

4.Question the homeowner to determine, if possible, what specifi c component is not functioning.

Use the map of the spa (see below); become familiar with the components and their names. This will also help when speaking to technical service.

Keep the Owner’s manuals in an accessible place.

Know the difference between the spa’s components and how they perform when utilized in the spa. Example: An air control will induce air into the plumbing of the jet, increase the fl ow of water and make the jet more powerful.

5.Ask what is showing on the control panel.

Are there any error messages? Ask the customer to specifi cally describe the topside control panel readout, if any.

6.Determine if the error message is the result of a safety feature or if a service call needs to be set up.

“Cool” and/or “Ice” are generally the result of a spa that has just been fi lled or refi lled and doesn’t require any action on the part of the homeowner or the technician.

Know how the fi ltration system works, what its defaults are, when it comes on and if there are any automatic times that it will come on during each day. Know the symptoms!

7.Setting up the appointment.

Make sure you verify the name, address, phone number and where the customer can be reached if not at home.

Ask if there is access to the spa if the owner is not going to be present.

Ask about anything that may bar your access to the spa such as locked gates, locked electrical boxes, vicious dogs, etc.

 

Diverter Valve

Remote Panel

 

 

 

 

Air Controls

 

Waterfalls

Pillow

 

 

 

 

 

Topside Control Panel

 

 

Wood Skirt

Pump #2

 

Filters

 

Fully Foamed

 

Jets

 

 

 

Load Box

 

Spa Map Pump #1

Circulation Pump

Removable Pan

6

8.Make Sure there is access to the main breaker and GFCI, and ask the homeowner to disconnect if possible before you arrive at their home.

9.Use the home service visit as an opportunity to sell aftermarket items such as chemicals, towels, etc.

10.Educate your staff regarding chemicals that are important for optimal use and longevity of the spa components.

Chemical misuse is not covered under the terms of the warranty.

11.Know what to recommend when the customer complains that they cannot get their chemicals properly balanced. This is not a service call covered by the warranty or a problem that involves the manufacturer.

All spas are used differently: heavy or light bather loads, adults only, the whole family, bromine or chlorine, etc.

12.Does the customer know how to properly clean the fi lter and that the spa needs to be disabled when doing so?

Suggest a second fi lter to the customer if the original fi lter needs to be soaked in a cleaning solution. Have one in your truck!

13.Find out what chemicals the customer is using. If they have saturated the spa with different kinds of chemicals, sometimes it is best to empty the spa and start all over.

BENEFITS YOU WILL RECOGNIZE

A satisfi ed customer is one who will continue to call upon you for business and does not contact your competitors.

Educating your staff will increase their value and allow you to focus on real service issues.

Being properly prepared will increase your productivity and permit you to enjoy a weekend once in a while.

Bottom Line: If you change the way you approach your customer, you’ll be putting more money in your pocket.

7

1.5 Preparing For A Service Call

1.Know what each call is asking of you; determine whether or not the extent of service can be handled with a simple phone call or if it requires a visit.

Determine whether the call is warranty or non warranty. Make sure the customer is aware that the manufacturer will not cover out-of-warranty service.

If you plan to charge the customer for travel expenses, make sure that they are aware of the costs before you show up.

2.Make sure all of your testing devices are functioning properly and extra batteries are on hand.

Always bring a meter; when calling technical support, please ensure that you have all of the pertinent information, such as the spa’s serial number, model number, the system you are working on, etc.

3.Prepare your route so you may complete the maximum number of service calls each day.

A map book or a large map of your service area will greatly increase your effi ciency.

4.Bring all the tools needed to properly perform service calls.

Always have your vehicle properly stocked with replacement parts.

Have a sump pump available for draining purposes; emptying a spa from the drain line takes a lot of your time, which we know is extremely valuable.

5.Properly prepare for the day’s service calls.

When reviewing your calls, think of every possible component and tool that you may need. For example, if there is a heating problem or the heater doesn’t come on, think of all the components that include anything to do with a heat call, such as the temperature sensor, circulation pump, main pump, fl ow or pressure switch, fi lter, circuit board, heater, etc.

Prepare for the worst possible scenario and plan to be able to satisfy the subsequent problems that may arise.

6.Dress appropriately. Although this is one job where shorts are acceptable, to maintain your credibility as a professional, leave the half shirts and shirts with derogatory or obscene comments at home.

Finish your cigarette before speaking with the spa owner and remember - no drugs or alcohol!

7.Be on time for your appointments. If you are going to be late or can’t make the appointment, call the customer to inform them of what’s happening.

Call your offi ce and ask them to call the people on your schedule to tell them you are running late.

8.Always support the product that you service.

Do not berate the product in front of the homeowner. It is essential to maintain the integrity and reputation of the product, and berating the product may affect your credibility as an authorized service professional.

If you feel there is a problem that needs special attention, call us or complete a quality alert. Remember, this is a partnership between you and the manufacturer - we want to provide the best quality product possible, with your business providing the best service possible!

8

9.Make professional repairs.

Putting bondo, underwater epoxy, silicone or any other product to fi x cracked or leaking plumbing will not adequately correct the problem and will most likely result in a return visit. Replace the component or come back and do it for free!

Make repairs look as good as or better then when you started.

10.Make sure you leave the customer’s home as clean as you found it.

Most customers don’t mind if you are having lunch in their backyard, as long as you remove the evidence! Make sure to pick up any trash that you may have generated through repairs as well as break times, lunch, etc.

11.Leave a work order with the customer explaining what you found to be the problem and how you corrected it.

Make sure the customer understands the work order.

12.Suggest to the customer any improvements they can make in maintaining their spa.

13.Recommend replacement fi lters or a new cover if there is a need for one. A spa vac is an easy sell once you demonstrate it to the customer.

14.Always carry a box of fi lters and a box of the basic chemicals; once you have fi nished the service, politely ask if they need any chemicals or a new fi lter. Drop off chemicals in a sealed box if they have ordered them when they made their service appointment.

1.6 Before Calling Technical Support

Make sure you have followed the STA and fi lled out a “Troubleshooting Data Col- lection Form” (see example on page 61). Have the STA manual and the Trouble- shooting Data Worksheet near the telephone. Technical Support can help you best if these things become the communications tools for the phone call.

1.7 Before Leaving The Customer

Even if you don’t have to fi ll out a Troubleshooting Data Collection Form, please do so. If this is a warranty repair, the information will be needed when your offi ce fi lls out the “Returned Goods/Labor Tag”. In any case, it will help you spot trouble before it happens. Pumps burn up if voltage at the hot tub is too low. Circuit breakers trip if heaters and motors draw too much current (Amps). Wires overheat and connections burn if wire size is too small or push-on connectors are loose. Call backs cause cost of service to increase!

9

1.8 Satisfying The Customer

Most customers do not care what work you have done or what parts you have replaced, but they always care whether or not their problem goes away. When you are done, show them that their problem is gone. If they ask how you did it, take a few minutes to explain. Show them the bad part(s) and explain or show why it is bad.

Develop the habit of examining the hot tub’s you service. Compliment customers on the things they are doing right. Tell them how their care and attention can stop trouble before it starts.

Mention if you noticed any adverse conditions, especially if the hot tub is under warranty or contract, that could lead to failure. Can the customer correct the problem? Would they like you to correct it? Can you recommend someone? Would they like an estimate?

Think of yourself and the customer as a “team” trying to keep the product up and running as costeffective and time-effi cient as possible. That’s good for the customer, and it’s good for your business.

10

2.0Electro Static Discharge

2.1ESD - What Is It? What Does It Do?

Static electricity is always being generated around us, even at those times when we no longer get zapped after walking across a rug and touching something.

Like all state-of-the-art circuit boards, the hot tub’s circuit board can be damaged by unnoticed static electricity. Damaged is the key word. Sometimes a board which has been subjected to ESD will fail immediately upon being put back into service. Usually a board will operate for a few days, or months, then fail.

If the hot tub runs only a few days, the customer thinks you provided poor service.

If the hot tub runs only a few months, the customer thinks the circuit board was a low quality product.

The customer loses use of the hot tub. You lose money because you must go back to make it right. Jacuzzi Premium loses its reputation for quality.

2.2 Avoiding ESD Damage

We can’t prevent static charges from building up within us as we go about our jobs, so we must do three things to protect circuit boards from getting zapped:

1. Never transport or ship circuit boards - good boards or bad boards - except in

 

 

 

 

 

the static protective bags.

 

N

J1

 

 

 

 

 

 

 

Spa Light

 

 

 

 

L

 

JP1

 

 

 

8

7

 

 

 

46

53

2.

Never remove the board from the static protective bag unless you are ready to

 

 

2

1

 

 

 

T

 

 

 

E

 

 

 

M

 

 

 

P

 

 

 

/H

 

 

 

I

 

 

 

-

 

 

 

L

 

 

 

I

 

 

 

M

 

 

 

I

 

 

 

T

 

install it in the hot tub.

 

 

 

F

 

 

 

 

L

 

 

 

 

O

 

 

 

 

W

 

 

 

 

S

 

 

 

 

W

 

 

Pump

 

 

3.

After removing the bad board from the hot tub, A) lay it on the ground, B) remove

 

 

 

L

1

J4

 

 

 

 

N

Pump

 

 

 

the replacement board from the static protective bag, C) lay the replacement board

 

 

 

 

L

2

 

 

 

 

Red Black

F

 

 

 

1

 

 

on the ground, D) place the bad board in the bag from which you removed the re-

 

 

 

 

placement board, E) return bad board(s) to Jacuzzi Premium in undamaged sealed static protective bags.

2.3 What About Wrist Straps And Special Mats?

The purpose of these devices is to keep the technician, the work surface and the circuit board at the same electrical potential, and drain into ground any static charges which might build up. Proper use of the wrist strap and special mat guarantees maximum protection against ESD damage.

2.4 Must Wrist Straps And Mats Be Used When Replacing A Circuit Board?

No, if you keep the spare board in the protective bag during transport and you observe a few simple techniques during replacement.

The possibility of ESD damage to the circuit board during replacement will be minimal because of the hot tub’s design and the way you normally work on it. Touching the ground lug will drain all built-up static charges from your body much like a wrist strap would. Laying the bad board on the ground will tend to keep it neutral. Touching a fi nger to the grounding lug immediately before removing the good board from the bag will drain charges built up by the rustling of your clothes. Laying the good board on the ground after removing it from the bag will tend to keep it neutral. Another quick touch of the grounding lug before picking up the bad board will drain built up charges. Slipping the bad board into the protective bag will allow it to be transported safely. Another quick touch of the grounding lug before picking up the good board will again drain any charges built up. In the process of installing the replacement board, you and the board will be grounded to the load box or grounding lug, draining off charges you may build up during installation.

11

3.0 Main System Specifi cations J-345

Dimensions ...............................

84” x 84” x 36” (213cm x 213cm x

 

92cm)

Dry Weight ................................

882 lbs (400kg)

Filled Weight .............................

3,611 lbs (1,638kg)

Water Capacity (Avg. Fill)

........336 US gallons (1,272 Liters)

Electronic Controls ..................

Solid State Electronic Controls with LED

 

Readout, Programmable Temperature,

 

Filtration, and Heat Cycles

Pump 1 ......................................

2-Speed, 4.2hp brake, 2.5hp continuous

Pump 2 ......................................

1-Speed, 4.2hp brake, 2.5hp continuous

Pump 3 ......................................

N/A

Circulation Pump ......................

Yes

Total PowerPro Jets .................

25

Maxx PowerPro (MX) ................

5

PowerPro (LX) ...........................

4

Mini PowerPro (FX) ..................

16

Micro PowerPro (SX) ................

N/A

Jet Selectors .............................

2

Air Controls ...............................

Four, On / Off Pushbutton Type

Total Foot Jet Therapy .............

2

Water Management System .....Two 60ft2 Filter Cartridges; Filter 1 on 24-Hour Circulation Pump; Filter 2

 

on 2-Speed Pump 1; Ready for optional CD Ozone Generator (Built-in

 

Ozone Dispersion Chamber Included in Spa)

Lighting .....................................

One Underwater with Two Colored Lenses

Cabinet ......................................

Redwood/Cedar with No Stain; Optional UV Resistant

 

Synthetic Plastic Cabinet with Embossed Red or Gray Wood Grain

Acrylic Colors ...........................

Textured Bluegrass, Jade, Marine, Onyx, Sahara, or Sand; Marbled

 

Emerald, Platinum, or Sapphire; Solid Azure or Silver

Headrests ..................................

4

Waterfall ....................................

Includes Flow Rate / On-Off Adjustment; Powered by Pump 1

Electrical Requirements ..........

North American 60Hz Models: 240 VAC @ 30A, 50A, or 60A

 

Export 50Hz Models: 230-240 VAC @ 35A or 40A, or suitably rated

 

circuit breaker to comply with local electrical codes. Certain

 

countries may require dual power inputs; two breakers are required

 

for this confi guration.

Warranty .................................

North American 60Hz Models: 10 Years Shell, 7 Years Shell Surface,

 

5 Years for Plumbing Component Leaks, 5 Years Equipment &

 

Controls; Export 50Hz Models: 2 Years Plumbing Component Leaks,

 

2 Years Equipment & Controls

Seating Capacity ....................

4 - 5

Audio System (Optional) .......

AM/FM/CD Stereo Receiver with Dual Pop-Up Speakers

 

Dimensions/Specifi cations are Subject to Change Without Notice

12

Jet Selector / Air Control Operation Diagram

Air Control 1:

Opens / Closes Air Inlet to Jet Group A

Air Control 2:

Opens / Closes Air Inlet to Jet Group C

Air Control 3:

Opens / Closes Air Inlet to Jet Group B

 

A

B

A

 

C

 

 

 

 

Jet Selector 2:

 

C

B

Directs Jet Pump 2

D

Output Between

 

 

Jet Groups C or D.

 

 

 

Air Control 4:

 

 

 

Opens / Closes

D

 

D

Air Inlet to Jet

 

 

 

 

Group D

 

 

 

Jet Selector 1:

Directs Jet Pump 1

Output Between Jet

Groups A or B.

 

Seat Depths

A = 25.50” (64.8cm)

F = 19.75” (50.2cm)

Listed Dimensions

B = 24.00” (60.1cm)

G = 27.00” (58.6cm)

Represent Distance from

C = 28.50” (72.4cm)

H = 25.75” (65.4cm)

Top of Acrylic to Lowest

D = 23.00” (58.4cm)

I = 34.00” (86.4cm)

Point in Seat.

E = 27.50” (69.9cm)

 

 

Dimensions/Specifi cations Subject to Change Without Notice

B

AC

H I D

G E

F

13

3.1 Main System Specifi cations J-335

Dimensions ...............................

84” x 84” x 36” (213cm x 213cm x

 

91cm)

Dry Weight ................................

781 lbs (354kg)

Filled Weight .............................

3,752 lbs (1,702kg)

Water Capacity (Avg. Fill)

........358 US gallons (1,355 Liters)

Electronic Controls ..................

Solid State Electronic Controls with LED

 

Readout, Programmable Temperature,

 

Filtration, and Heat Cycles

Pump 1 ......................................

2-Speed, 4.2hp brake, 2.5hp continuous

Pump 2 ......................................

N/A

Pump 3 ......................................

N/A

Circulation Pump ......................

Yes

Total PowerPro Jets .................

24

Maxx PowerPro (MX) ................

N/A

PowerPro (LX) ...........................

4

Mini PowerPro (FX) ..................

18

Micro PowerPro (SX) ................

2

Jet Selectors .............................

1

Air Controls ...............................

Three, On / Off Pushbutton Type

Total Foot Jet Therapy .............

2

Water Management System .....Two 60ft2 Filter Cartridges; Filter 1 on 24-Hour Circulation Pump; Filter 2

 

on 2-Speed Pump 1; Ready for optional CD Ozone Generator (Built-in

 

Ozone Dispersion Chamber Included in Spa)

Lighting .....................................

One Underwater with Two Colored Lenses

Cabinet ......................................

Redwood/Cedar with No Stain; Optional UV Resistant

 

Synthetic Plastic Cabinet with Embossed Red or Gray Wood Grain

Acrylic Colors ...........................

Textured Bluegrass, Jade, Marine, Onyx, Sahara, or Sand; Marbled

 

Emerald, Platinum, or Sapphire; Solid Azure or Silver

Headrests ..................................

4

Waterfall ....................................

Includes Flow Rate / On-Off Adjustment; Powered by Pump 1

Electrical Requirements ..........

North American 60Hz Models: 240 VAC @ 30A or 50A

 

Export 50Hz Models: 230-240 VAC @ 35A or 40A, or suitably rated

 

circuit breaker to comply with local electrical codes. Certain

 

countries may require dual power inputs; two breakers are required

 

for this confi guration.

Warranty .................................

North American 60Hz Models: 10 Years Shell, 7 Years Shell Surface,

 

5 Years for Plumbing Component Leaks, 5 Years Equipment &

 

Controls; Export 50Hz Models: 2 Years Plumbing Component Leaks,

 

2 Years Equipment & Controls

Seating Capacity ....................

5

Audio System (Optional) .......

AM/FM/CD Stereo Receiver with Dual Pop-Up Speakers

 

Dimensions/Specifi cations are Subject to Change Without Notice

14

Jet Selector / Air Control Operation Diagram

Air Control 1:

Opens / Closes Air Inlet to Jet Group C

Jet Selector:

Directs Jet Pump Output Between Jet Groups A&B or C.

A C

A

B

Air Control 2:

Opens / Closes C Air Inlet to All

Lounge Jets A

B B

Air Control 3:

Opens / Closes

Air Inlet to Jet

Group B

 

Seat Depths

A = 26.50” (67.3cm)

F = 19.75” (50.2cm)

Listed Dimensions

B = 24.00” (60.1cm)

G = 27.00” (68.6cm)

Represent Distance from

C = 28.75” (73.0cm)

H = 34.00” (86.4cm)

Top of Acrylic to Lowest

D = 23.00” (58.4cm)

 

Point in Seat.

E = 27.50” (69.9cm)

 

 

Dimensions/Specifi cations Subject to Change Without Notice

B

A C

HD

G E

F

15

3.2 Main System Specifi cations J-325

Dimensions ...............................

84” x 76” x 34” (213cm x 193cm x

 

86cm)

Dry Weight ................................

738 lbs (335kg)

Filled Weight .............................

3,386 lbs (1,536kg)

Water Capacity (Avg. Fill)

........320 US gallons (1,211 Liters)

Electronic Controls ..................

Solid State Electronic Controls with LED

 

Readout, Programmable Temperature,

 

Filtration, and Heat Cycles

Pump 1 ......................................

2-Speed, 2.0hp brake, 1.5hp continuous

Pump 2 ......................................

N/A

Pump 3 ......................................

N/A

Circulation Pump ......................

Yes

Total PowerPro Jets .................

15

Maxx PowerPro (MX) ................

N/A

PowerPro (LX) ...........................

11

Mini PowerPro (FX) ..................

4

Micro PowerPro (SX) ................

N/A

Jet Selectors .............................

1

Air Controls ...............................

Three, On / Off Pushbutton Type

Total Foot Jet Therapy .............

2

Water Management System .....Two 60ft2 Filter Cartridges; Filter 1 on 24-Hour Circulation Pump; Filter 2

 

on 2-Speed Pump 1; Ready for optional CD Ozone Generator (Built-in

 

Ozone Dispersion Chamber Included in Spa)

Lighting .....................................

One Underwater with Two Colored Lenses

Cabinet ......................................

Redwood/Cedar with No Stain; Optional UV Resistant

 

Synthetic Plastic Cabinet with Embossed Red or Gray Wood Grain

Acrylic Colors ...........................

Textured Bluegrass, Jade, Marine, Onyx, Sahara, or Sand; Marbled

 

Emerald, Platinum, or Sapphire; Solid Azure or Silver

Headrests ..................................

4

Waterfall ....................................

Includes Flow Rate / On-Off Adjustment; Powered by Pump 1

Electrical Requirements ..........

North American 60Hz Models: 120 VAC @ 15A or 240 VAC @ 30A or

 

40A, Export 50Hz Models: 230-240 VAC @ 35A or 40A, or suitably

 

rated circuit breaker to comply with local electrical codes. Certain

 

countries may require dual power inputs; two breakers are required

 

for this confi guration.

Warranty .................................

North American 60Hz Models: 10 Years Shell, 7 Years Shell Surface,

 

5 Years for Plumbing Component Leaks, 5 Years Equipment &

 

Controls; Export 50Hz Models: 2 Years Plumbing Component Leaks,

 

2 Years Equipment & Controls

Seating Capacity ....................

4

Audio System (Optional) .......

N/A

 

Dimensions/Specifi cations are Subject to Change Without Notice

16

Jet Selector / Air Control Operation Diagram

Air Control 1:

Opens / Closes

Air Inlet to Jet

Group A

 

 

A

Jet Selector:

A

 

Directs Jet Pump

 

 

 

Output Between

 

 

Jet Groups A or

B C

B

B&C

 

Air Control 3:

 

 

Opens / Closes

 

 

Air Inlet to Jet

 

 

Group C

C

B

Air Control 2:

Opens / Closes

Air Inlet to Jet

Group B

 

Seat Depths

A = 27.00” (68.6cm)

F = 31.25” (79.4cm)

Listed Dimensions

B = 27.25” (69.2cm)

 

Represent Distance from

C = 25.75” (65.4cm)

 

Top of Acrylic to Lowest

D = 21.50” (54.6cm)

 

Point in Seat.

E = 28.00” (71.1cm)

 

 

Dimensions/Specifi cations Subject to Change Without Notice

AB

F

E D C

17

3.3 Main System Specifi cations J-315

Dimensions ...............................

76” x 66” x 32” (193cm x 168cm x

 

81cm)

Dry Weight ................................

640 lbs (290kg)

Filled Weight .............................

2,283 lbs (1036kg)

Water Capacity (Avg. Fill)

........200 US gallons (757 Liters)

Electronic Controls ..................

Solid State Electronic Controls with LED

 

Readout, Programmable Temperature,

 

Filtration, and Heat Cycles

Pump 1 ......................................

2-Speed, 2.0hp brake, 1.5hp continuous

Pump 2 ......................................

N/A

Pump 3 ......................................

N/A

Circulation Pump ......................

Yes

Total PowerPro Jets .................

13

Maxx PowerPro (MX) ................

N/A

PowerPro (LX) ...........................

7

Mini PowerPro (FX) ..................

6

Micro PowerPro (SX) ................

N/A

Jet Selectors .............................

1

Air Controls ...............................

Two, On / Off Pushbutton Type

Total Foot Jet Therapy .............

2

Water Management System .....Two 60ft2 Filter Cartridges; Filter 1 on 24-Hour Circulation Pump; Filter 2

 

on 2-Speed Pump 1; Ready for optional CD Ozone Generator (Built-in

 

Ozone Dispersion Chamber Included in Spa)

Lighting .....................................

One Underwater with Two Colored Lenses

Cabinet ......................................

Redwood/Cedar with No Stain; Optional UV Resistant

 

Synthetic Plastic Cabinet with Embossed Red or Gray Wood Grain

Acrylic Colors ...........................

Textured Bluegrass, Jade, Marine, Onyx, Sahara, or Sand; Marbled

 

Emerald, Platinum, or Sapphire; Solid Azure or Silver

Headrests ..................................

3

Waterfall ....................................

Includes Flow Rate / On-Off Adjustment; Powered by Pump 1

Electrical Requirements ..........

North American 60Hz Models: 120 VAC @ 15A or 240 VAC @ 30A or

 

40A, Export 50Hz Models: 230-240 VAC @ 35A or 40A, or suitably

 

rated circuit breaker to comply with local electrical codes. Certain

 

countries may require dual power inputs; two breakers are required

 

for this confi guration.

Warranty .................................

North American 60Hz Models: 10 Years Shell, 7 Years Shell Surface,

 

5 Years for Plumbing Component Leaks, 5 Years Equipment &

 

Controls; Export 50Hz Models: 2 Years Plumbing Component Leaks,

 

2 Years Equipment & Controls

Seating Capacity ....................

3

Audio System (Optional) .......

N/A

 

Dimensions/Specifi cations are Subject to Change Without Notice

18

Jet Selector / Air Control Operation Diagram

Jet Selector:

Air Control 1:

Directs Jet Pump

Opens / Closes

Output Between

Air Inlet to Jet

Jet Groups A or B

Group A

A B

A

B

Air Control 2:

Opens / Closes

Air Inlet to Jet

Group B

 

Seat Depths

A = 26.50” (67.3cm)

Listed Dimensions

B = 28.00” (71.1cm)

Represent Distance from

C = 27.00” (68.6cm)

Top of Acrylic to Lowest

D = 28.00” (71.1cm)

Point in Seat.

E = 27.75” (70.5cm)

 

 

Dimensions/Specifi cations Subject to Change Without Notice

A B

E D C

19

Loading...
+ 43 hidden pages