Size:
3.45 Mb
Download

J-200Series

CAUTION: Turn off power to hot tub!

Follow the directions on page 35 for draining the spa.

1.As the water level drops below the seats, use whatever means necessary to get the water out of the recessed seating areas and into the foot well.

2.When the water level ceases to drop, use whatever means available to remove any remaining water from the foot well.

3.Turn off power to the spa.

4.Remove the synthetic cabinet panel under the control panel and locate the drain plugs on the front of the pump(s), (Figure A, page 17). Remove plugs to allow water to drain out of pumps and heater.

Note: Approximately one to two gallons will be released during this procedure. Use a wet/dry vacuum or other means to keep this from flooding the equipment compartment. Replace the drain plugs.

5.Re-installsynthetic cabinet side panel and cover spa so that no casual moisture can enter into it.

Consult your authorized Jacuzzi dealer if you have any questions regarding winter use or winterizing.

12.8Restarting Your Spa in Cold Weather

If you want to start up your spa after it has sat empty for a time in freezing temperatures, be aware that the water remaining in certain sections of the piping may still be frozen. This situation will block water flow preventing the spa from operating properly and possibly damaging the equipment. We recommend you consult your authorized Jacuzzi dealer for guidance before attempting to re-startyour spa under these conditions.

13.0 Water Quality Maintenance

To decrease the risk of contracting a waterborne illness (e.g. an infection, bacteria or virus) and/or respiratory ailments, maintain water quality within specified limits. This will enhance your enjoyment and prolong the life of the hot tub’s equipment. Doing so requires regular attention because the water chemistry involved is a balance of several factors.

Procrastination in regard to water maintenance will result in poor and potentially unhealthful conditions for soaking and even damage to your hot tub investment. For specific guidance on maintaining water quality, consult your Authorized Jacuzzi dealer who can recommend appropriate

chemical products for sanitizing and maintaining your hot tub.

37

J-200Series

WARNING: Failure to maintain water quality

!can result in:

Increase risk of contracting a waterborne illness (e.g. an infection bacteria or virus) and/or respiratory ailments.

Damage the equipment, components and spa shell, which are not covered under the hot tub’s warranty.

CAUTION: Never store hot tub chemicals inside the hot tub’s equipment bay. The equipment bay may reach elevated temperatures, this is where high voltage electronic devices are located. This area is not intended for storage of any kind.

13.1pH Control

pH is a measure of relative acidity or alkalinity of water and is measured on a scale of 0 to 14. The midpoint of 7 is said to be neutral, above which is alkaline and below which is acidic. In spa water, it is very important

to maintain a slightly alkaline condition of 7.4 to 7.6. Problems become proportionately severe the further outside of this range the water gets.

A low pH will be corrosive to metals in the spa equipment. A high pH will cause minerals to deposit on the interior surface (scaling).

In addition, the ability of the sanitation agents to keep the spa clean is severely affected as the pH moves beyond the ideal range. That is why almost all spa water test kits contain a measure for pH as well as the

sanitizer.

13.2Sanitizing

To destroy bacteria and organic compounds in the spa water, a sanitizer must be used regularly. Chlorine and bromine are the two most popular sanitizers used to date. Many other additives are available for your spa. Some are necessary to compensate for out-of-balancewater, some aid in cosmetic water treatment and others simply alter the feel or smell of the water. Your authorized Jacuzzi dealer can advise you on the use

of these additives. When adding spa shock (chlorine or non-chlorine)or pH balancing chemicals activate the jets pump(s) and leave the spa cover open for a minimum of 20 minutes. By doing this you will allow excessive chemical vapors to exit the spa, protecting pillows and plastic

knobs from chemical attack.

38

J-200Series

WARNING: Risk of PERSONAL injury, drowning

!OR entrapment!

Never leave your hot tub unattended for any reason while the cover is open and accessible, especially to small children and animals!

CAUTION: Risk of PERSONAL injury OR SPA DAMAGE!

Never add chlorine tablets (trichlor) or acid to your hot tub for any reason! These chemical may damage components within your hot tub, burn or irritate your skin, create a rash and void the manufacturer warranty for your spa.

13.3Optional CD Ozone Water Maintenance System

If you have elected to have your spa equipped with the optional Jacuzzi CD ozone water purification system you will find that your water stays fresh and clear with significantly less chemical sanitizer usage. You will

also probably be able to go longer between complete spa drainings.

14.0 Error Conditions/Error Messages

Your spa has a self-diagnosticcontrol system. The system will automatically display the following if a problem is detected.

14.1Summer Logic (Spas With Circulation Pump Option)

When the actual spa water temperature reaches up to

2°F (1°C) above the set temperature, the spa goes into “summer logic.” The 24-hourcirculation pump will turn off

automatically to avoid adding additional heat to the water, eventually creating an overheat condition. This setting is not user-programmable.

Note: The summer logic does not take effect until the spa water temperature reaches 95°F (35°C). This condition is more likely in excessively hot weather. Remember, the spa’s ability to cool is directly affected by the ambient temperature. An excessively hot ambient temperature may prevent the spa from cooling down because it’s fully insulated construction is designed to retain heat and to minimize operating costs.

14.2 Panel Displays COL

Cool Condition - Temperature has dropped 20°F (11°C) below the current set temperature. Jets pump 1, (oroptional circulation pump) and the heater have been activated to bring the temperature to within 15°F (8°C) of the set temperature. No corrective action is required!

Note: This condition is common during first time fill ups or during refills since tap water is often very cold.

39

J-200Series

14.3Panel Displays ICE

Freeze Protection - A potential freeze condition has been detected. No action is required. Jets pump (or optionalcirculation pump) and heater will operate to circulate and warm water through the plumbing until spa is out of DANGER. See “Winterizing” (page 36).

14.4Panel Displays SN1

Open sensor (heater is disabled) or shorted sensor (spa is deactivated). Thehigh-limittemperature sensor is notfunctioning. Contact your authorized Jacuzzi dealer or qualified service technician.

14.5Panel Displays SN2

Open or shorted sensor (heater disabled). The temperature sensor is not functioning. Contact your authorized Jacuzzi dealer or qualified service technician.

14.6 Panel Flashes FL1 or FL2 (Spas Without Circulation Pump Option)

A flashing “FL1” display means the pressure switch is not closed when the jets pump 1 is activated. Proper water

flow is inhibited or the pressure switch has malfunctioned. A flashing “FL2” display means the pressure switch is malfunctioning closed. In either case, the heater is deactivated. To correct condition, perform to the following:

1.Verify water level is one inch below lowest pillow. Add water if necessary.

2.Check for clogged or dirty filter cartridge (sec. 12.1, page 32).

3.Purge “air lock” from jets pump 1 by loosening the upper pump head drain screw (Figure A, page 17) for a few seconds to release trapped air, then retighten drain screw. FINGER TIGHT ONLY!

4.If problem persists, contact your authorized Jacuzzi dealer.

14.7Panel Flashes FL1 or FL2 (Spas With Circulation Pump Option)

A flashing “FL1” display means the flow switch is malfunctioning open, the filter cartridge is excessively dirty or an “air lock” condition has occurred at the circulation pump intake. A flashing “FL2” display means the flow switch is malfunctioning closed. In either case,

the spa heater will deactivate and jets pump #1 may also deactivate. To correct condition perform the following:

40

J-200Series

1.Verify water level is 1" below lowest pillow. Add water if necessary.

2.Check for clogged or dirty filter cartridge (sec. 12.1, page 32).

3.Purge “air lock” from circulation pump intake by removing filter cartridge. Hold your garden hose over the filter cartridge wall fitting while using a rag as a seal around hose end. Ask a helper to turn on water for 30 seconds, then turn off. Reinstall filter cartridge and check spa (sec. 12.1, page 32).

4.If the circulation pump is not running, turn power off at the main breaker, then turn power back on. This will reset the circulation pump priming cycle. Once the pump is primed, the error should clear.

5.If problem persists, contact your authorized Jacuzzi dealer.

14.8Panel Displays OH

! WARNING: Risk of Hyperthermia(over-heating)

Causing Severe Injury, burns, or welts.

Water temperature is above acceptable limits. DO NOT ENTER SPA! Water temperature has reached 112˚F(44˚C) and the low speed jets pump 1 and optionalcirculation pump (when equipped) has activated to circulate water through heater. Contact your authorized Jacuzzi dealer or qualified service technician.

14.9Panel Displays (- - -)

! WARNING: Risk of Hyperthermia(over-heating)

Causing Severe Injury, burns, or welts.

Water temperature is above acceptable limits. DO NOT

ENTER SPA! The safety “Watchdog” software has been triggered and the spa is deactivated. A problem has been

detected which could cause damage to the spa or its

components. Contact your authorized Jacuzzi dealer or qualified service technician.

41

J-200Series

15.0 Troubleshooting Procedures

In the event your Jacuzzi® spa is not working the way it should, please first review all the installation and operating instructions in this manual and check the message on the panel display. If you are still not satisfied it is working properly, please follow the appropriate troubleshooting instructions below.

Note: If any of the supply cords to the accessories are damaged, they must be replaced by authorized service personnel. Contact your authorized Jacuzzi dealer or qualified service technician.

15.1 None of the Components Operate (e.g. Pump, Light)

Check the following:

1.Is there power to the spa?

2.Is the household circuit breaker tripped?

3.Contact your authorized Jacuzzi dealer or qualified service technician.

15.2Pump Does Not Operate But Light Does

Press the JETS 1 button:

1. If no water movement is detected, make sure power is going to the spa and check the water level. If it does not solve the problem, contact your authorized Jacuzzi dealer or qualified service technician.

2. The main jets pump 1 operates but no water flows to jets. Check the following:

• Jets may all be closed in spa. Verify all jets are in the open “on” position (sec. 10.5, page 27).

• Pump may not be properly primed. This can happen after the spa is drained and refilled. Press the JETS 1 button on the control panel several times, never leaving the motor running for more than 5 to 10 seconds at a time. Turn power off and let the air out of spa plumbing system by removing the filter cartridge (sec. 12.1, page 32). Make certain you reinstall the filter cartridge before turning on spa power and restarting the jets pump 1.

15.3Poor Jet Action

1.Make sure jets are in the full open “on” position (page 27).

2.Press the JETS 1 button to make certain pump #1 is on.

3.Open all air controls to their full on position (counterclockwise).

4.Check for dirty filter. Clean, if necessary (section 12.1, page 32).

15.4 Water is Too Hot

Reduce thermostat setting.

42

J-200Series

15.5No Heat

1.Check thermostat setting.

2.Keep the spa cover in place while heating.

3.Check the settings to see if your spa is in economy filtration/heating mode (page 28).

Should checking the above steps fail to correct the problem, please call your dealer so that they may arrange service. We build the best spas in the industry. Nonetheless, we are always striving to improve the quality and features of our products.

Your input as a Jacuzzi spa owner is a cherished part of this process. If you have any comments or suggestions, or if you wish to be informed on any new products for your spa, please write to us.

CONGRATULATIONS on your good taste and welcome to the happiest and most relaxed family in the world!

43

44

 

 

 

 

 

 

 

 

 

 

 

Logic Jumper Settings (Factory Defaults Shown)

Optional

 

BLK

 

 

 

 

 

Control Panel

JP1 1-2ON

= 40A Logic

 

 

 

 

 

 

 

JP1 1-2OFF

= 50A Logic (Factory Default Setting)

LED Lighting

 

WHT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JP1 3-4ON

= 2 Pump Operation (Not used on J-230)

System DCU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

 

JP1 3-4OFF

= 1 Pump Operation

 

 

 

 

 

 

 

 

 

JP1 5-6ON

= 60A Logic (Remove JP1 1-2Jumper)

 

 

 

 

 

 

 

 

 

 

 

Standard

 

BLK

J20

K1

 

 

 

J1

 

 

 

(Not used on J-230)

 

 

 

 

 

 

 

JP1 5-6OFF

= Leave of for 40A or 50A Logic

Footwell

 

WHT

J21

 

 

 

 

JP1

Light

 

 

 

 

 

 

JP1 7-8ON

= °C Temperature Display

 

 

 

 

 

 

 

OZONATOR (OPTIONAL)

 

 

 

 

 

 

8

7

JP1 7-8OFF

= °F Temperature Display

 

 

 

 

 

 

6

5

 

 

O3

 

WHT

J11

 

 

 

 

 

4

3

 

TEMPERATURE SENSOR

CIRC.

 

BLK

K2

 

 

 

 

2

1

 

 

J12

 

 

 

 

 

 

 

SENSOR

PUMP

 

WHT

J13

 

 

 

 

 

J2

 

 

* Shown

C

K3

 

 

 

 

 

 

 

with Optional

BLK

J14

 

 

 

 

 

 

 

FLOW SWITCH

Circulation

 

 

 

 

TRANSFORMER

 

 

J3

 

 

 

 

 

 

 

 

 

 

 

 

Pump

 

WHT

J15

K4

 

 

 

 

 

 

 

 

 

240 VAC

 

 

 

 

 

 

LO

 

BLK

 

 

 

 

 

 

 

 

 

 

 

 

J16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This device complies with Part 15 of the

 

 

 

 

K5

 

 

 

 

 

 

PUMP 1

 

RED

J17

 

 

 

 

 

 

FCC rules. Operation is subject to the

 

 

 

 

 

 

 

 

following two conditions:

 

 

 

 

 

 

 

 

 

 

HI

 

 

 

 

 

J4

 

 

 

 

1. This device may not cause harmful

 

 

WHT

 

 

 

F1

 

 

 

 

interference.

 

 

J18

 

 

 

 

 

 

2. This device must accept any inteference

 

 

 

K6

 

K7

 

K8

 

received including interference that may

 

 

 

 

 

 

 

cause undesired operation.

 

 

 

 

 

 

 

 

 

 

 

 

BLK

J19

 

 

 

 

 

 

 

 

PUMP 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HI

 

 

RED

 

BLK

J77

J86

J92

J104

 

 

 

 

 

 

 

 

 

 

 

 

 

J6

 

J5

 

 

 

 

 

 

 

Not used on J-230

F1

RED BLK

RED BLK

30A, 250V

 

 

SC-30

 

 

 

 

Heater

 

 

 

5.5 kW

TB1

 

Optional

240 VAC

 

 

 

Stereo

 

1

2

Power Supply

 

 

 

 

 

Standard 240 VAC, 3-WireConnection (60Hz,1-PhaseService)

GRN RED

BLK

USE COPPER CONDUCTORS ONLY. WIRE SIZE MUST

BE APPROPRIATE PER NEC AND/OR LOCAL CODES

.Option

Circulation the Without or With models spa American North Hz 60

240V 280-Jand270-J230,-Jall for used is diagram wiring This

Models 280-Jand270-J230,-JAmerican North 1.16

Diagrams Board Circuit 0.16

Series 200-J

 

Pump

 

 

 

 

J-200Series

16.2North American J-210Convertible Models

This wiring diagram is used for all J-210120/240V 60 Hz North American convertible spa models.

J1 Logic Jumper Settings (Factory Defaults Shown)

JP1 1-2

ON

= 30A Logic (4-wire120/240 VAC operation only)

JP1 1-2

OFF = 40A Logic (4-wire120/240 VAC operation only)

JP1 7-8

ON

= °C Temperature Display

JP1 7-8

OFF = °F Temperature Display

Control

Panel

Spa Light

BLK

O3

Optional

Ozonator

BLK

WHT

WHT

 

 

F1

 

 

20A

 

 

250V

Plug-in

 

SC-20

 

 

GFCI

 

 

Cord (US

GROUND

 

Models

 

Only) OR

 

 

Hard

GRN

 

Wire

 

 

TB1

 

 

 

3 BLK

 

BLK

BLK

 

2 WHT

 

WHT

 

1

J21

J20

J1

 

 

8

7

 

Temperature Sensor

 

6

5

 

 

4

3

 

 

 

2

1

J2

 

 

 

 

 

J12

 

 

 

Sensor

 

 

 

 

J14

 

 

J3

Switch

J16

 

 

 

Transformer

 

 

 

 

 

 

 

 

120 VAC

J11

F1

 

 

 

J15

K5

K7

K8

J5

J13

J6

 

 

Heater IN

Heater OUT

WHT

J17

J7

J8

J9

J10

 

 

 

Main Pump

RED

BLK

RED BLK

 

BLK

WHT

 

 

 

 

 

LO

HI

RED

 

 

THERM

 

 

 

 

 

 

 

 

 

 

SWITCH

 

 

 

 

 

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any inteference received including interference that may cause undesired operation.

Heater

1.0 kW @ 120 VAC (3-wireconnection)

4.0 kW @ 240 VAC (4-wireconnection)

 

 

Standard 3-Wire120 VAC Connection (60 Hz, 1 Phase, 15A Service)

 

 

 

 

RED*

 

Use copper conductors ONLY. Wire size must be appropriate per NEC and/or local codes.

 

 

 

 

WARNING, ELECTRICAL SHOCK HAZARD EXISTS! Always remove power to spa before wiring and/or configuring the circuit board

 

GROUND

To circuit board

Hard

 

 

 

 

Wire

GRN

RED*

ove

Wi

Only

TB1

 

M

 

 

 

 

r

 

 

 

 

e

 

 

3

 

 

 

 

BLK

2

BLK WHT

 

WHT

1

 

RED*

 

 

 

 

 

 

 

 

 

Optional 4-Wire240/120 VAC Convertible Heater Connection

1.Remove and discard the factory installed GFCI Cord.

2.Move RED* wire from TB1 position #1 to TB1 position #3 as shown below.

3.Permanently connect to the power supply. Use copper conductors ONLY. Wire size must be appropriate per NEC and/or local codes.

4.If hot tub is to be operated on 30A service, make sure the jumper provided at location JP1 #1&2 on the circuit board is installed. If hot tub is to be operated on 40A service, remove the jumper JP1 #1&2 on the circuit board.

45

46

 

 

 

 

 

 

 

 

 

Logic Jumper Settings (Factory Defaults Shown)

 

 

 

 

 

 

 

Control Panel

JP1 1-2ON

= 20A Logic (Factory Default Setting)

 

 

 

 

 

 

 

JP1 1-2OFF

= 30A Logic

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JP1 3-4ON

= 2 Pump Operation (Not used on J-230)

 

 

 

 

 

 

 

 

 

JP1 3-4OFF

= 1 Pump Operation

SPA LIGHT

 

 

 

 

 

 

 

 

JP1 5-6ON

= 40A Logic (Remove JP1 1-2Jumper)

 

 

BLK

J20

 

 

 

 

 

 

(Not used on J-230)

 

 

 

K1

 

 

J1

 

JP1 5-6OFF

= Leave of for 20A or 30A Logic

 

 

WHT

 

 

 

 

 

 

 

 

 

 

 

JP1 7-8ON

= Celsius Temperature Display

 

 

J21

 

 

 

 

JP1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JP1 7-8OFF

= Fahrenheit Temperature Display

OZONATOR (OPTIONAL)

 

 

 

 

 

8

7

 

 

 

 

 

 

 

O3

 

 

 

 

 

 

6

5

 

 

 

BLU

J11

 

 

 

4

3

 

TEMPERATURE SENSOR

CIRC.

 

BRN

K2

 

 

2

1

 

 

J12

 

 

 

 

 

 

* Shown PUMP

C

BLU

J13

 

 

 

J2

HI - LIMIT / FREEZE SENSOR

with Optional

 

 

 

 

 

BRN

K3

 

 

 

 

 

 

Circulation

J14

 

 

 

 

 

PRESSURE SWITCH

 

 

 

 

 

 

Pump

 

 

 

 

 

 

 

 

 

 

 

 

TRANSFORMER

 

J3

 

 

 

 

BLU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J15

K4

240 VAC

 

 

 

 

 

 

 

 

 

 

 

 

 

LO

 

 

 

 

 

 

 

 

 

 

 

 

BRN

J16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PUMP 1

 

BLK

 

K5

 

 

 

 

 

 

 

J17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HI

 

BLU

 

 

J4

 

 

 

 

 

 

 

J18

 

 

 

 

 

 

 

 

 

 

K6

 

K7

K8

 

 

 

 

 

 

 

 

 

 

 

 

 

BRN

J19

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PUMP 2

 

 

 

 

F1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HI

 

 

BLU

BRN

J77

J86

J92

J104

 

 

 

 

 

 

 

 

 

 

J6

J5

 

 

 

 

 

 

Not used on J-230

 

 

F1

BLU

BRN

BLU

BRN

 

 

 

 

 

 

20A, 250V

 

 

 

 

 

 

 

 

 

SC-20

 

 

 

 

 

 

Heater 2.7 kW @ 230 VAC

TB1

 

 

1

 

 

 

 

 

 

2

Power Supply

 

Optional Stereo And Power

 

 

 

 

 

 

 

 

 

 

 

 

Supply on J-335,J-345

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Models Only.

 

 

 

 

 

 

 

 

 

 

 

230 VAC 3-WireConnection (50Hz,1-PhaseService)

 

 

 

 

 

 

 

 

 

 

 

USE COPPER CONDUCTORS ONLY. WIRE SIZE MUST BE

 

 

GRN

BLU BRN

APPROPRIATE PER NEC AND/OR LOCAL CODES

 

Without or With models spa Export

J all for used is diagram wiring This

270-J230,-JHz 50 Export 3.16

Series 200-J

 

 

 

 

 

Option Pump Circulation the

230V 280-Jand270-J230,-

Models 280-Jand

 

.

50

 

 

 

 

Hz

 

 

J-200Series

16.4Export 50 Hz J-210Models

This wiring diagram is used for all J-210230V 50 Hz Export spa models.

J1 Logic Jumper Settings

 

 

 

 

JP1 1-2ON

= 20A Logic (Factory Setting)

 

 

 

JP1 1-2OFF = 30A Logic

 

 

Control

 

JP1 7-8ON

= °C Temperature Display (Factory Setting)

 

Panel

 

JP1 7-8OFF = °F Temperature Display

 

 

 

 

 

 

J21

J20

J1

 

 

 

 

 

8

7

 

Temperature Sensor

 

 

 

 

6

5

 

 

Spa Light

 

4

3

 

 

 

 

2

1

J2

 

 

 

 

 

 

 

 

 

 

BLK

J12

 

 

 

Sensor

 

 

 

 

 

 

O3

Optional

 

 

 

 

J3

Pressure Switch

Ozonator

 

J14

 

 

 

 

 

 

 

 

BRN

J16

 

 

 

Transformer

 

 

 

 

 

 

 

230 VAC

 

 

 

J11

F1*

 

 

 

 

 

 

BLU

J15

K5

 

 

K7

 

K8

 

 

 

 

 

 

 

 

 

 

 

J5

 

 

 

 

 

 

 

 

 

 

J13

 

 

 

 

 

 

 

 

 

 

BRN

 

 

 

 

 

 

 

 

F1

 

J6

 

 

Heater IN

Heater OUT

 

 

20A

 

 

J17

J7

J8

J9

J10

 

 

250V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SC-20

 

 

 

 

 

 

BLU BRN

 

 

GROUND

 

 

Main Pump

BLK

 

 

 

 

 

BRN

 

 

 

 

 

 

 

BLU

HI

 

 

 

THERM

 

 

 

 

 

LO

 

 

 

SWITCH

 

GRN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hard

 

 

 

 

 

 

BLU

 

 

Heater

Wire

 

 

 

 

 

 

BRN

 

2.7kW @ 230 VAC

Only

 

 

 

 

 

 

 

 

TB1 BLU

BLU 2BLUBRN

BRN 1BRN

Standard 3-Wire230 VAC Connection (50 Hz, 1 Phase Service)

Use copper conductors ONLY. Wire size must be appropriate per NEC and/or local codes.

47

J-200Series

17.0 Optional Stereo Receiver Functions

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

J-230,J-270andJ-280Models Only:

To start enjoying your new stereo receiver, please read the following operation instructions in their entirety.

1.Power Button: Press PWR (Power) to turn deck on or off.

2.Equalization Button: Repeatedly press EQ/LD to choose from DSP Off, Jazz, Pop, Classic, Rock or Vocal equalization options. Press and hold EQ/LD for 2 seconds to enable or disable the “LOUD” function.

Special Recommendation: After you have powered up your Aquatic AV Audio System, we suggest you try one of the preset DSP (digital sound presets) settings to customize the sound in your spas audio system. It’s easy, simply press the EQ/LD button (2) to activate the DSP. Then repeatedly press to choose from Jazz, Pop, Classical, Rock and Vocal DSP settings. This will enhance your listening experience and make it more enjoyable.

3.Mute Button: Press Mute to mute audio output. Press again to return to previous volume level.

4.Open Button: Press Open to flip down the front access panel for CD access. Gently insert CD into slot (DO NOT FORCE!) Make sure to close the front panel to prevent damage to the unit.

Note: Never insert a wet or moist CD since it may damage the mechanism and void the manufacturer warranty.

5.A/PS Button: Press A/PS to scan station presets. The tuner will scan up, wait for a few seconds, then continue. Once a desired station is found, press A/PS a second time to cancel scan. To

48

J-200Series

automatically scan and store station presets, simply press and hold A/PS for several seconds, then release.

6.DISP Button: Press DISP to switch between clock and station frequency. When selected, the clock will display for 5 seconds then automatically revert back to station frequency.

7.Source Button: Press Source to change input from audio or CD mode to auxiliary mode. Press a second time to switch back.

8.Volume Buttons: Press + (Volume Up) or - (Volume Down) to increase or decrease volume level.

9.SEL Button: Press SEL to choose control function:

Bass

Treble

Balance

Fader

Volume

To adjust selection, press + (Volume Up) or - (Volume Down). Bass control: Adjusts the amount of low frequency. Treble control: Adjusts the amount of high frequency. Balance control adjusts the amount of sound output to the left and right speakers. Fader control adjusts the amount of sound output. You can decrease the sound level of the rear speakers by pressing + (Volume Up). To decrease the sound level of the front speakers press - (Volume Down).

Note: Bass and Treble settings are available only if EQ is set to DSP Off.

10.Preset 1/Pause Play Button: In tuner mode, any station can be stored as preset 1 by pressing and holding this button for 2 seconds. To recall the station preset, simply press and release this button. In

CD mode pressing this button will pause or play the CD.

11.Preset 2/INT Button: In tuner mode, any station can be stored as preset 2 by simply pressing and holding this button for 2 seconds. To recall the station preset, simply press and release this button. In

CD mode pressing this button will preview each song on the disc for about 10 seconds. Simply press again to turn off this feature.

12.Preset 3/RPT Button: In tuner mode, any station can be stored as preset 3 by simply pressing and holding this button for several seconds. To recall the station preset, simply press and release this button. In CD mode pressing this button will play a song repeatedly. Press again to turn off this feature.

49

J-200Series

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

13.Preset 4/RDM Button: In tuner mode, any station can be stored as preset 4 by simply pressing and holding this button for several seconds. To recall the station preset, simply press and release this button. In CD mode press this button to randomly play song tracks. Press again to turn off this feature.

14.Preset 5/DN Button: In tuner mode, any station can be stored as preset 5 by simply pressing and holding this button for several seconds. To recall the station preset, simply press and release this

button. In CD mode this button will browse the folders on CD-RandCD-RWdisks.

15.Preset 6/UP Button: In tuner mode, any station can be stored as preset 6 by simply pressing and holding this button for several seconds. To recall the station preset, simply press and release this

button. In CD mode this button will browse the folders on CD-RandCD-RWdisks.

16.BND Button: Press BND to select one of the following frequency bands: FM1, FM2, FM3, AM1, AM2 and WB (weather band)

17.Tuning UP/DOWN Buttons: Press Track Up to manually adjust station frequency up. Press and hold Track Up to scan for next higher station. Scan mode stops as soon as a strong station is found. Press Track Down to manually adjust frequency down. Press and hold Track Down to scan for next lower station. Scan mode stops as soon as a strong station is found. In CD mode pressing these buttons will advance the CD up or down to the next or previous track. To fast forward or rewind through a track, simply press and hold either button as desired during CD playback.

18.Reset Button (Not Illustrated): If keys do not function at all and the unit appears to be “locked up”, use a ballpoint pen to press the Reset Button under the front panel (press OPEN to flip down front panel for access). The Reset Button is located directly below the Eject Button.

Press to clear all memory (except station presets) and reset deck.

Note: This action will reset the display and clock to default setting.

50

J-200Series

19.Eject Button (Not Illustrated): To eject CD, press OPEN and flipdown the front access panel, then press the Eject button located to the left of CD slot.

20.USA/Europe Switch (Not Illustrated): You can switch between

American (USA) and European radio frequency bands by flipping a

switch located on the bottom of the deck. To change bands:

Power down unit.

Lift up sticker under the CD player.

Choose desired frequency band as indicated on the sticker.

Put sticker back in place and power up the unit.

21.Setting The Clock (Unit Must be Off): To set the current time, press and hold Display (6) for 3 seconds until the clock display starts to blink, then set hours using the Track Up and/or Track Down button (17). Press Display a second time to set minutes, using the Track Up and/or Track Down buttons. Press and hold Display a third time to exit clock setup (or simply wait for 5 seconds).

22.Selecting Weather Band Mode: Press BND (16) while in tuner mode until WB displays (deck automatically skips to the strongest weather channel) or press BND a second time to return to previous mode. When WB weather band mode is active:

Press Track Up (17) to scan to higher weather channel.

Press Track Down (17) to scan to lower weather channel.

To save a weather channel preset, press and hold one of six numeric keys 1-6.

Note: Weather channel 7 is not accessible through preset key.

23.Display information DISP:

When a retail music CD is inserted, press DISP (6) to change modes as follows:

Clock (displays for 5 seconds only).

CD track no./Playtime

When a CD containing MP3 files is inserted, press DISP (6) change modes as follows:

Clock (displays for 5 seconds only).

Track no./Playtime

Folder name

File name

Song name

Artist’s name

Album name

The system can only display the first 8 letters of ID3 tags. If the recorded information is longer than 8 letters, text will scroll to the left once, then the 8 first letters will be displayed. If specific info has not been recorded on an MP3 disc, NO FOLD, NO TRK, NO TLT, NO ALBM, NO ART will display.

51

J-200Series

24. Playback Order of The MP3 File:

A directory that does not include an MP3 file is skipped.

We recommend that you make no more than two levels for each disc.

Maximum number of folders: 256

Maximum number of folder levels: 8

Maximum number of characters for MP3 file name and folder name: 32

Sampling frequency: 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48kHz

Bit rates: 8-320Kbps

MP3 decoding format: MPEG 1 and 2 Audio Layer 3

Folder names and file names can be displayed with up to 8 characters (see Display key).

The characters A-Z,0-9can be displayed on this unit, other characters may not be displayed correctly.

ID3 tag is supported (see Display key).

25.Reading files into a disc: When a disc containing MP3 data is loaded, the unit checks all the data on the disc. If the disc contains numerous folders with many levels, it takes a longer time to start playback. In addition, it may take time for the unit to move to the next MP3 file and the fast forward function may not be performed smoothly. When selected to play, files and folders are accessed in order in which they were written by the CD writer. Therefore, the playing order may not be the same as the order in which they are expected. For example, a disc with the following folder/file hierarchy is subject to folder select, file select and playback order as illustrated on page 53.

26.Optional Audio Receiver Specifications

Marine Grade AM/FM/CD/CD-R/CD-RW/MP-3

7 Bands of Weather Band

Stainless Steel Sealed Chassis and Mounting Hardware

IPX5 Water Intrusion and CFR-46Rated

Conformal Coated Printed Circuit Boards

ASTMB117 Salt Fog Tested 400 Hours

ASTM D4329 UV Stable Tested 400 Hours

Double Sealed Water Protection Transport Gaskets

White Low Current/Low Heat LCD

White Backlit Control Surfaces

5 Band Digital Sound Stage Settings

200 Watt, 50 x 4

MP3 with ID-3Tag, Video

Switchable Tuner Frequency U.S. or Euro Band/CE Approved

52

53

Example of a disc's folder/file hierarchy

Operation of the keys

Level 1 Level 2 Level 3 Level 4 Level 5

Press (Track Down) to select folder down

Press (Track UP) to select folder up

Press and hold 5 to return 10 files behind.

Press and hold 6 to go 10 files forward.

Folder File

Series 200-J

J-200Series

Serial Number: ____________________________

Model Name: _ ___________________________

Dealer Name: _ ___________________________

Notes: _ __________________________________

_________________________________________

_________________________________________

_________________________________________

54

J-200Series

55

J-200Series

56