Page 1
JABRA FreeSpeakTMQUICK START GUIDE
For Nextel Phones
Model #:100-91030000-02
Model #:100-91130000-02
Model #:100-91430000-02
BEFORE USING YOUR HEADSET
Charge FreeSpeak – FreeSpeak is rechargeable and must be charged before use.
1. Insert the headset fully into its multi-adapter.
2. Plug one end of the AC power adapter into the multi-adapter and the other end into an
electrical wall outlet.
3. Charge your headset for approximately 2 hours or until both blue indicator lights go out.
Important: Blue indicator lights on the headset and multi-adapter will both be on while
charging and will turn off when charging is complete.
Connect multi-adapter to phone
• For phones with standard 2.5mm headset jacks: Plug the multi-adapter’s connector into the
2.5mm headset jack on your phone.
• For i2000plus, i2000, i1000plus, i1000, r750plus, i700plus, i550plus, i500plus and i500
phones: Plug the audio adapter (sold separately) into your phone. Then plug the multi-
adapter’s connector into the audio adapter.
IMPORTANT
READ THIS FIRST
Location of phone’s headset
jack may vary.
Headset Indicator Light
(Blue LED)
Multi-Function Button
Volume Control Button
MiniGel™
NON-BT
Page 2
BASIC OPERATIONS
Turn headset on/off – Press the multi-function button for 3 to 5 seconds until you see a
burst of flashes on the blue indicator light, then release. The indicator lights on the headset and
multi-adapter will flash every 3 seconds while the power is on and in “Standby” mode.
If you are already wearing the headset, you’ll hear a quick series of FOUR tones when turning the
headset on or off. When turning on, their pitch will be low to high, and when turning off, their
pitch will be high to low.
Important: Do not hold the button down too long (more than 3 to 5 seconds) when
turning on headset or else the headset may go into pairing mode, and the blue indicator light
will turn solid. If that happens, the section below titled “If you press and release and
the headset stays in Standby mode” may be applicable to you.
Choose wearing preference – FreeSpeak is ready to wear on
the right ear. If you prefer the left, gently rotate the MiniGel 180°.
Make, answer, and end calls (details on p.12-15 of User Guide)
1. To make or answer calls, press and release ONCE to move the headset
from “Standby” to “Active” mode, turning on the audio link between the headset
and the multi-adapter. (It may take a few seconds for the audio link to start, so don’t
press the again.) In
Active mode, the indicator lights flash every second.
2. You will then need to dial or answer the call using the phone’s keypad.
3. When you’re done with the call, use the phone’s keypad to end the call.
4. Then press and release again to return to Standby, turning off the audio link.
Calls can be made by using voice-activated dialing (available in certain Nextel phone
models).
Important: Do not hold the button down too long when switching modes; this should
only be a quick tap.
Multi-adapter
Stylus
Switch
Stylus
Turning multi-adapter on/off - The multi-adapter turns on automatically when you undock the headset, and it turns off when you
dock the headset. To turn it off without docking, you can insert
the stylus into the stylus switch then press and release the
switch. Repeating this will turn it on.
Page 3
What you see
What you hear
Status
Flashes every second
Flashes every 3
seconds
When Active Mode
starts: quick series
of TWO tones – low
to high pitch
When Standby
Mode starts: quick
series of TWO
tones – high to low
pitch
Active Mode
• Call in progress
• Up to 4 hours of talk time
Standby Mode
• Waiting for call
• Up to 100 hours of standby time with
mheadset in multi-adapter
ST
ATUS INDICATORS
To answer and end calls with only the headset:
Some phones enable you to answer or end a call by pressing and releasing without having
to touch the phone. For all Nextel phone models (except the i1000), the phone’s Automatic
Answer feature needs to be activated for this headset feature to work.
For the BlackBerry 6510, FreeSpeak's Anwer/End feature has to be turned on.
To turn on FreeSpeak's Answer/End feature:
1) Ensure that the AC power adapter is not connected.
2) Put the headset in the multi-adapter.
3) Use the stylus to press the stylus switch for about 12 seconds.
4) You will then see a number of blinks (long flashes) on the multi-adapter indicator
light which tell you whether this feature is enabled or disabled according to the
following table:
5) Repeat steps 1-4 to switch between enabled and disabled settings.
If you are enabling Answer/End feature for the first time, you should test answering and ending
calls to ensure that your phone supports this feature.
For more information, see “Enhanced Features” at www.jabra.com/fscs.
Calls can be ended by the headset only by waiting for the line to disconnect.
Number of Blinks
Answer/End Feature Comments
4
5
Enabled
Disabled
Default Setting
--
Page 4
If you hear an echo of your voice – You may need to adjust
microphone levels.
To reduce the echo:
Flashes or
Beeps
Microphone Level
1
2
3
High (default)
Medium
Low
1. Lower the volume of your phone and headset.
2. If echo persists, put FreeSpeak in Active mode.
3. Use the stylus to press down on the stylus switch (as shown above) until you see a solid
c blue light on the multi-adapter. Continue to press down until you see/hear 1, 2, or 3
z flashes/beeps, then release. The last number of flashes/beeps corresponds to the final
c setting.
4. Repeat step 3 to cycle between different microphone levels.
TIPS & SOLUTIONS
To prolong battery life:
• After you’ve ended a call using your phone’s keypad, always remember to place the
headset in Standby mode by pressing and releasing when not in use.
• Dock the headset firmly in its multi-adapter when not in use.
If you press and release and the headset stays in Standby mode:
If FreeSpeak becomes unpaired, it will not respond to the button. In rare cases, this may
occur when you first receive the product or when you hold the button too long while using
the product.
To “pair” the headset with the multi-adapter:
1. Ensure headset is off.
2. Press until you see a solid blue light on the headset, then release.
3. Use the stylus to press down on the
stylus switch until you see a solid blue
light on the multi-adapter, then
release.
Important: Once pairing is complete,
lights on both the headset and multiadapter will begin flashing (Standby
mode).
Multi-adapter
Stylus
Switch
Stylus
Page 5
Need more help?
1. Consult the complete User’s Guide
2. Web: www.jabra.com/fscs (for the latest support info)
3. Telephone: (858) 622-9955, Monday to Friday 8am to 5pm PST
(800) EAR-2230 (USA and Canada)
To improve audio clarity:
Stay within 30 feet (10 meters) of your multi-adapter. In general, you will get the best performance when there are no obstructions (including parts of the body) between your headset and the
multi-adapter.
If the headset is not responding or the light will not turn off after pairing - You may need to
reset your headset.
1. Plug one end of the AC power adapter into the multi-adapter and the other end into an
electrical wall outlet.
2. Insert the headset into the multi-adapter for about 3 seconds, then remove.
Loading...