Page 1
IRDE-20031B4-00D-11
Page 11 of 17
Irradiant – LED 6 IZ Eyes Effect Light
IRDE-20031B4-00D-11
User Manual
Products Introduction
IRDE-20031B4-00D-11 is a LED high power Six Eyes Effect Light which is made up of each 1 piece of red、
green and blue LED. It has five kinds of operation modes: DMX、3- Channel、Auto、Sound activate, Master-slave.
The light has visional and strobe effect. It is cheap、 easy to operate、 with good effect、 and easy to install which
is applicable to all kinds of amenities and house party.
Please read this manual carefully before use the fixture and keep it for your future reference.
Note:
Caustic or deliquescent chemical can cause damage to the housing, except for presentation.
The operation temperature must be below 40℃，humidity is 0~95％. If it is used out of this range, the lifespan of
the fixture will be shortened.
Indoor use only
Warning：
When the product is in the package box, please do not connect it to the pow er.
T o make sure of the safety, ple ase do no t con nec t to the high voltage power before installation.
User can not take apart the fixture. If there is any problem with the fixture, please ask professional staff to repair.
Page 2
IRDE-20031B4-00D-11
Page 12 of 17
The input voltage need to match the voltage the fixture requested.
Please pay attention to waterproof, electricity proof and shockproof.
Packaging List
z LED Six Eyes Light
--------------------------------------------------------------------------------------------1 piece
z User Manual
---------------------------------------------------------------------------------------------1 piece
z Power Cord
---------------------------------------------------------------------------------------------1 piece
Specifications
1、Voltage：AC220-240V 50HZ
2、Power：14W
3、Light Source：1pc 1W red LED; 1pc 1W green LED; 1pc 1W blue LED;
4、Function：DMX512，3 CHANNEL，Sound activate，auto，Master-Slave
5、DMX Channel：4
6、Dimension：255x175x255mm
7、Net W e ight：3.6 KG
Operation Instruction
一、Panel Direction:
1、DIP SWITCH 2、MIC 3、Sensitivity 4、Power input / FUSE 5、DMX Input 6、DMX Output
Page 3
IRDE-20031B4-00D-11
Page 13 of 17
二．Four operation Modes：
Auto mode——do not receive the outside control but send the data of the subordinate machine
Sound mode——receive the sound control and send the data of the subordinate machine
DMX mode——receive the data from DMX512 controller and the host computer
3 CHANNEL mode——receive the data about R、G、B from 3 CHANNEL controller
1. Dip- switch function as below:
0=OFF 1=ON X=0FF or ON
DIPSWITCH CHART
FUNCTION
#1 #2 #3 #4 #5 #6 #7 #8 #9 #10
K0 K0 K0 F S S S 0 1 1 Auto
K1 K1 K1 K1 S S S 1 0 1 Sound
X X X X X X X 0 0 1 3 CHANNEL
SET DMX ADDRESS 0 DMX512
KO，K1 stands for different color selection，F stands for strobe，S stands for rotation speed，
see below table in detail
2
. Dip switch selection under auto and sound mode：
2-1、Auto mode：
2-2、Dip switch under sound activate mode：
#1 #2 #3 K0 colo
r
selection #4 #5 #6 #7 S: motor speed
0 0 0 RGB change 0 0 0 Automatic speed adjustment
1 0 0 G 1 0 0
1 1 0 RG 0 1 0
0 1 0 B 1 1 0
1 0 1 GB 0 0 1
0 0 1 R 1 0 1
0 1 1 RB 0 1 1
1 1 1 RGB
F=1
Strobe
F=0
No
strobe
111
slow
fast
#1 #2 #3 #4 K1 sound mode #5 #6 #7 S: motor s
p
eed
0 0 0 0 RGB switch 0 0 0 Automatic speed adjustment
1 0 0 0 R 1 0 0
0 1 0 0 G 0 1 0
0 0 1 0 B 1 1 0
0 0 0 1 RGB 0 0 1
1 0 1 0 RB 1 0 1
0 1 1 0 GB 0 1 1
1 1 0 0 RG 1 1 1
slow
fast
3．OBEY-3 Channel Description：
OBEY-3 Channel Function DMX512 No.
Description
CH1 adjust Red brightness 0～255 Adjust Red brightness is 0%～100%.
CH2 adjust green brightness 0～255 Adjust green brightness is 0%～100%.
CH3 adjust blue brightness 0～255 Adjust blue brightness is 0%～100%.
Page 4
IRDE-20031B4-00D-11
Page 14 of 17
4. DMX-512 mode and DMX address：
When dip switch 10= on，it performs DMX mode. Dip switch 1~9 is used to set DMX address.
DMX 512 Address Chart:
Dip-switches
# 1 # 2 # 3 # 4 # 5
# 6 # 7 # 8 # 9 # 10
Value
1 2 4 8 16
32 64 128 256 OFF
Example
Channel 1：Dip/on: #1 (=1)
Channel 5：Dip/on: #1, #3 (1+4=5)
Channel 13：Dip/on: #1, #3, #4 (1+4+8=13)
Channel function instruction
4.1、DMX PIN：
PIN1 GND GROUND
PIN2 - COLD Signal PIN3 + HOT Signal +
4.2、Multiple units connection under DMX Mode：
In DMX Out
DMX Controller
DMX out
In DMX Out In DMX Out
Page 5
IRDE-20031B4-00D-11
Page 15 of 17
DMX Connection testing ： Use Pin3 connecting-machine line to connect all the fixtures according to the method
showed in the above drawing. All fixtures are set in DMX mode and the receiving addresses are the same
(ranging from 001-511). After connect to the power, the fixture are run simultaneously.
4.3、Master-Slave：The fixture can operate simultaneously under auto and sound mode.
Installation
Hanging or Horizontally Installing
The fixture can be placed on the floor or fixed and hung by the clamp. When hanging, you can fix the
clamp through the middle spot of the bracket and the safety chain to assure safety. The safety chain should bear
the weight ten times more than the hanging object.
Trouble shooting
Troubles Reason Trouble shooting
The fixture does
not work
1. Check power input is matched with that
specified on this unit.
2.Check whether the fuse is burnt
1. Please confirm power input is matched
with that specified on this unit.
2. Change into the same type of fuse as
requested.
LED is very dim
1. Check power input is matched with that
specified on this unit.
2. Please confirm power input is matched
with that specified on this unit.
Not work under
sound mode
1.Check whether it is in sound mode 1.Check the operation mode is in sound
DMX does not
receive signal
1 ． Check whether the signal of DMX
Controller is reversed.
2．Check whether it is in DMX mode
1．Put the DMX signal in the right place.
2．Set operation mode: DMX mode
Loading...