IPSI CDP3KPS48-3P, CDP3KPS48, CDP3KPS24-3P, CDP3KPS24 Datasheet

CDP3K.qxd 6/6/03 4:07 pm Page 1

AC/DC Rectifier/Front End

3000 Watts			XPiQ inc.
CDP3K Series			Intelligent Design Quality Product
			Hot Swap N + 1 Redundant
	•
			•
			Single Phase or Three Phase Input
			•
			Rack Option for 3 Modules
			•
			Single Wire Current Sharing
			•
			Power Factor Corrected
			•
			Constant Power Characteristics
			•
			International Safety Approvals

Specification

Input

Input Voltage	• 180-264 VAC single phase
		(nominal 208 VAC, 3 phase optional)
Input Frequency	•	47-63 Hz
Inrush Current	•	50	A max
Input Current	•	19	A at 180 VAC full load single phase
		11	A/phase at 180 VAC full load
		3 phase
Remote On/Off	• On = TTL high or open,
		Off = TTL low
Input Fusing	•	25	A internal
Transient Protection	• MOV and Gas Tube

Output

Output Voltage	•	27 VDC or -54 VDC nominal
Output Power	•	3,000 Watts
Minimum Load	•	No minimum load required
Output Voltage Range •		19 V to 30 V or -40 V to -59 VDC
		programmable
Line/Load Regulation	•	±0.5% using remote sense,
		otherwise ±5%
Ripple & Noise	•	±1% pk-pk
Transient Response	•	3% Max deviation 500 µs recovery
		time for a 25% load change
Start-up Time	•	2 seconds max

Overtemperature	• Shutdown at +95 °C with auto reset
Protection
Remote Sense	• Compensates for up to 0.5 V loss
Current Share	•	Single wire ±5% at full load
Oring Diodes	•	Built in

General

Efficiency	•	90% typical at 230 VAC
Power Factor	•	0.99 for single phase input
		0.95 for 3 phase input
MTBF	•	300,000 hrs per Bellcore-std
LED Indicators	•	AC OK (Amber), DC OK (Green)
		Temp OK (Green)
Size	•	5.00” x 5.00” x 12.12”
		(not including handle)
Environmental
Operating	•	0 °C to +50 °C,
Temperature		derate linearly 2.2%/°C to +65 °C
Cooling	•	Internal ball bearing fan
Humidity	•	<95% RH, non-condensing
Storage	•	-40 °C to +70 °C
Temperature
Shock & Vibration	•	MIL STD-810F, NEBS Compliant to
		Bellcore GR63

Hold Up Time	•	>20 ms at low line
Output Rise Time	•	250 ms
Overshoot/Undershoot•		1% at turn on/off
Temperature	•	0.02%/°C
Coefficient
Overvoltage	•	29 V to 32.5 V or -58.5 V to -59.5 V
Protection		recycle input to reset
Overcurrent	•	110% to 140% with auto recovery
Protection		Constant power mode

EMC & Safety

Safety Approvals	• UL1950, CSA 22.2 No.650, EN60950,
		CE Mark LVD
EMI/EMC	•	Meets EN61000-3-2, -3
		CISPR22 and FCC Part 15 Class A,
		Bellcore GR-1089-Core
Immunity and Surge	•	Meets EN55082-2
		(EN61000-4-2, -3, -4, -5)
		Performance criteria A

•				PH: 508	429.9883	•
				FAX: 800	226.2100
	www.XPiQ.com			Email: [e-mail]
				Holliston, MA 01746 USA

CDP3K.qxd 6/6/03 4:07 pm Page 2

OUTPUT VOLTAGE & CURRENT RATINGS							CDP3K
Voltage		Output Voltage		Output	Standby	Max	Model
Set Point		Range(2)		Current	Output	Power	Number(1)
27	VDC	+20 to +29	VDC	148.8 to 102.4 A	5.0 V/0.5 A	3,000 W	CDP3KPS24
-54	VDC	-40 to -58	VDC	74.4 to 51.2 A	5.0 V/0.5 A	3,000 W	CDP3KPS48

Notes

1.For optional 3 phase AC input, add suffix ‘-3P’ to model number.

2.CDP3KPS24 is factory set to 27 V/110 A, CDP3KPS48 is factory set to -54 V/55 A. Voltages within each range are available - consult Technical Sales.

•

Mechanical Details - Module

Weight : 10.7 lbs, 4.85 kg

LEDs

1 AC Good (Amber)

2 Temp OK (Green)

3 DC Good (Green)

Single Phase

3 Phase

Input Mating Connector is: Positronics PLB06F0000 with FC114N2 pins.

Input Connector

Positronics

PLA04M4BN0A1

Input Mating Connector is: Positronics PLA04F8000 with FC114N2 pins.

www.XPiQ.com

PH: 508 429.9883

FAX: [phone] Email: [e-mail] Holliston, MA 01746 USA