Parts Catalog
Tilt and Recline (2GTR™)
Issued: Jun 25, 2008
Tarsys®
Tilt Only (2GT™)
Recline Only (2GR™)
For 2G/3G Storm Series® RWD
and Arrow® FWD
Powered Wheelchairs
Yes, you can. ™
Throughout this catalog you will notice letters to draw your attention to specific footnotes which are located at the
bottom of the page or below specified charts.
Parts Catalog Usage Guide
To order call toll free 1-800-333-6900, or www.invacare.com
The information contained in this document is subject to change without notice. This catalog contains
service parts for Form No. 99-150. If you have any questions regarding this catalog, please contact one
of our Customer Service Representatives.
For Customer Service Support Call:
1-800-333-6900
For Faxed In Orders Call:
1-800-678-4682 or
1-440-366-0709
For Technical Service Call:
1-800-832-4707
Literature Can Be Found at:
www.invacare.com or
1-800-828-6272
SYMBOL DEFINITION
Examples:
A,B,C etc.
NOTE:
NLA
= Special Comments
= General information pertaining to that specific page
= No Longer Available
HARDWARE MEASUREMENTS
The measurements for the hardware will be listed as follows:
Screws, Bolts
Washers
Spacers
For your convenience, we have supplied an area for you to list your Invacare Representatives.
©2008 Invacare Corporation. Elyria, Ohio. Invacare, Yes, you can., the Blue Medallion Design, Storm Series, Arrow, Silhouette, Contour U, and Arrow are
registered trademarks and 2GT, 2GR, 2GTR, MKIV, Infinity, and Personal Back are trademarks of Invacare Corporation.
Otto Bock is a registered trademark owned by Otto Bock Orthopaedische Industrie GMBH & Co.. JAY Back is a registered trademark of Sunrise Medical
Diameter X Thread Count/Pitch X Length
Inside Diameter X Outside Diameter X Thickness
Inside Diameter X Outside Diameter X Length
Name Phone Numbers
HHG, Inc. Corporation
Form No.
99-150
1
Accessories, Back Hardware (Infinity, Personal, JAY, Silhouette, Contour U Backs w/ Extruded
Canes) (Profile Back w/ 7/8" Round Canes)
TABLE of CONTENTS
Page
Number
To order call toll free 1-800-333-6900, or www.invacare.com
Form No.
99-150
Description
Accessories, Arm Pads - Otto Bock ......................................................................................... 141
153
Accessories, Headrest Support Assembly - A.B.S. Curved and Profile Back .......................... 143
Accessories, Lateral Support Assembly ................................................................................... 145
Accessories, Miscellaneous .................................................................................................... 158
Accessories, Power Wheelchair Tool Kit .................................................................................. 156
Accessories, Vent Tray Assembly (FWD) ................................................................................ 150
Accessories, Vent Tray Assembly (RWD) ................................................................................ 147
Armrest Assembly - 2GR and 2GTR ........................................................................................ 85
Armrest Assembly - 2GT .......................................................................................................... 82
Back Assembly - V.S.R. Actuator Motor & Attaching Hardware - 2GR and 2GTR .................. 80
Back Assembly Attaching Hardware - A.B.S. Curved and Profile ............................................ 77
Back Cane (7/8" Round) and Spreader Bar Assembly - 2GT .................................................. 40
Back Cane and Spreader Bar Assembly - Recline Only and Tilt/ Recline ............................... 42
Back Cane and Spreader Bar Assembly - Tilt Only ................................................................. 37
Back, A.B.S. Curved w/o Hardware - 2GR/2GTR w/ V.S.R. (After 4/20/03) ............................ 70
Back, A.B.S. Curved w/o Hardware - 2GR/2GTR w/ V.S.R. (Before 4/21/03) ......................... 63
Back, A.B.S. Curved w/o Hardware - 2GT (After 10/31/00) ..................................................... 54
Back, A.B.S. Curved w/o Hardware - 2GT (Before 11/1/00) .................................................... 45
Back, Profile without Attaching Hardware ................................................................................ 75
Electronics - Mid-Line Swing Bracket Assembly ...................................................................... 134
2
TABLE of CONTENTS
Page
Number
To order call toll free 1-800-333-6900, or www.invacare.com
Form No.
99-150
Description
Electronics - MKIV TRCM 2G, MKIV TAC & 4-Way Switch ..................................................... 127
Electronics - MKIV TRCM 2G, MKIV TAC & 4-Way Switch For TRBKTS Option .................... 130
Electronics - Quad Link (QLA) After 10/30/05 .......................................................................... 139
Electronics - Quad Link Before 10/31/05 .................................................................................. 136
Electronics - Tilt Recline Single Switch (TRSS) ....................................................................... 125
Electronics - Tilt/ Recline Potentiometers and Hardware ......................................................... 132
Frame, Base Interface Hardware - 2GR (FWD) ....................................................................... 20
Frame, Base Interface Hardware - 2GR (RWD) ....................................................................... 9
Frame, Base Interface Hardware (Includes Tilt Actuator) - 2GT/2GTR (FWD) ........................ 18
Frame, Base Interface Hardware (Includes Tilt Actuator) - 2GT/2GTR (RWD) ....................... 13
Frame, Base Interface Hardware w/ TRBKTS Option - 2GR (RWD) ....................................... 11
Frame, Base Interface w/ TRBKTS Option (Includes Tilt Actuator) - 2GT/2GTR (RWD) ......... 15
Frame, Center Seat Assembly - 2GT ...................................................................................... 26
Frame, Center Seat Assembly (Includes Recline Actuator) - 2GR ......................................... 28
Frame, Center Seat Assembly (Includes Recline Actuator) - 2GTR ....................................... 30
Frame, Center Seat Attaching Hardware - (RWD and FWD) ................................................... 24
Frames, Side ............................................................................................................................ 22
Front Pivot Bracket and Links Kit ............................................................................................. 32
Front Rigging - Front Rigging Hanger Assembly - Sector, Pin and Genius Style .................... 93
Front Rigging - Legrest Support Push Rod Assembly .............................................................. 123
Front Rigging - Legrest Supports (Mechanical) - AT5544P ..................................................... 95
3
Front Rigging - Power Non-Articulating Legrest Kits - POWELR18/POWELR20
(9/15/01-4/30/02)
TABLE of CONTENTS
Page
Number
To order call toll free 1-800-333-6900, or www.invacare.com
Form No.
99-150
Description
Front Rigging - Legrest, Genius (Mechanical) .......................................................................... 97
Front Rigging - Power Articulating Legrest - ELRPW (5/1/02-7/26/04) .................................... 108
Front Rigging - Power Articulating Legrest - ELRPW (After 7/26/04) ....................................... 111
Front Rigging - Power Articulating Legrest - POWELR18/POWELR20 (Before 9/15/01) ........ 101
Front Rigging - Power Articulating Legrest Kits - ELRPW (5/1/02-7/26/04) ............................. 120
Front Rigging - Power Articulating Legrest Kits - ELRPW (After 7/26/04) ................................ 122
Front Rigging - Power Articulating Legrest Kits - POWELR18/POWELR20 (Before 9/15/01) . 116
Front Rigging - Power Articulating/Non-Articulating Legrest Harnesses and Hardware .......... 114
Front Rigging - Power Non-Articulating Legrest - POWELR18/POWELR20 (9/15/01-4/30/02)
Label Locations For TRBKTS Option ....................................................................................... 7
Packaging and Literature ......................................................................................................... 5
Seat Pan ................................................................................................................................... 34
Seat Pan Mounting Hardware .................................................................................................. 35
Shroud Covers, Controller ........................................................................................................ 90
Shroud Covers, Rear, Side, Lower Seat and V.S.R. Actuator ................................................. 88
TRBKTS Option Clarification Reference .................................................................................. 8
105
119
4
Packaging and Literature
Form No.
99-150
5
To order call toll free 1-800-333-6900, or www.invacare.com
Packaging and Literature
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1030364 Carton, Cover 1 11 B
1091514 Insert, Carton 1 12
40131X161 Insert, Plain Pad 1 23
1106472 Carton 1 14
1021149 Bag, Poly Zip-Lip (13" Long x 9" Wide) 1 15
1080876 Carton 1 16
1092284 Insert, Carton 1 17
40131X045 Carton 1 18
1091517 Carton 1 19
See Note See Footnote 1 110 D
1030362 Carton, Tray 1 211
1115174 Carton, Corner Reinforcement 1 412
00077X031 Warranty Card 1 1A
1134791 Manual, Owner's 3G Storm w/ MKIV Electronics 1 1A,B
1031682 Carton, Cover 1 1A,C
1030362 Carton, Tray 1 1A,C
A - Not Shown
B - All Systems
C - Complete Seating Systems with Chair Base
D - Wood skid not supplied
NOTE:
When adjusting or replacing parts, please refer to you Owner's Manual for assistance.
NOTE:
Form No.
99-150
6
To order call toll free 1-800-333-6900, or www.invacare.com
Label Locations For TRBKTS Option
Form No.
99-150
7
To order call toll free 1-800-333-6900, or www.invacare.com
TRBKTS Option Clarification Reference
TRBKTS Option was introduced 12/19/05 as an On-Chair option only for 3G RWD Storm Series models.
Form No.
99-150
8
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (RWD)
Recline Only (2GR)
Form No.
99-150
9
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (RWD)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1082873 Pivot Assembly, Rear 1 11
1030949 Screw, Hex Head (1/4-20 x 1-1/2") 1 62
1086943 Bar, Spacer, Black 1 23
1070462 Screw, Hex Head Cap w/ Patch (5/16-18 x 7/8") 1 64
1082872 Bracket, Pivot, Front, Black 1 15 A
1086944 Screw, Socket Head Cap (5/16-18 x 3/4") 1 46
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 57
1082880 Support, Seat 1 28
1069724 T-Nut (5/16-18) 1 69
7930318 Screw, Phillips Pan Head (#4-40 x 1/2") 25 110
1070430 Bracket, Charger Connector, Black 1 111
P0870X000 Nut, Hex Keps (#4-40) 1 212
A - Front pivot bracket made before 5/20/02 is no longer available. For seating systems manufactured before 5/20/02, see
Front Pivot Bracket and Links Kit page and order Kit part number 1112693.
NOTE:
Recline Only (2GR)
Form No.
99-150
10
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (RWD)
Recline Only (2GR) with TRBKTS Option
Form No.
99-150
11
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (RWD)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1082873 Pivot Assembly, Rear 1 11
1030949 Screw, Hex Head (1/4-20 x 1-1/2") 1 62
1086943 Bar, Spacer, Black 1 23
1070462 Screw, Hex Head Cap w/ Patch (5/16-18 x 7/8") 1 44
1082872 Bracket, Pivot, Front, Black 1 15
1021344 Screw, Socket Head Cap (5/16-18 x 1-1/2") 1 46
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 67
1082880 Support, Seat 1 28
1140342 Spacer, Seat Support Mounting 1 29
1069724 T-Nut (5/16-18) 1 610
1043627 Screw, Hex Head Cap with Patch (5/16-18 x 1-3/4") 1 211
1070430 Bracket, Charger Connector, Black 1 112
1140259 Kit, Front/Rear Tie-Down Brackets Mounting
Hardware
1 113 A
Screw, Hex Head (5/16-18 x 3/4") 1 414
Washer, Flat (5/16 x 5/8 x 1/16") 1 415
T-Nut (5/16-18) 1 416
Screw, Socket Head Cap with Patch (5/16-18 x
1-3/4")
1 417
Screw, Socket Head Cap (3/8-16 x 3/4") 1 218
1140263 Kit, Top Battery Support Bracket and Mounting
Hardware
1 119 B
Bracket, Top Battery Support 1 120
Washer, Flat (5/16 x 5/8 x 1/16") 1 721
Screw, Hex Head (5/16-18 x 5/8") 1 322
Screw, Hex Head Cap with Patch (5/16-18 x 3/4") 1 423
T-Nut (5/16-18) 1 424
1135963 Bracket, Battery Support, Black 1 125
1140260 Kit, Front Battery Support Bracket with Mounting
Hardware
1 126 C
Bracket, Battery Support, Black - Front 1 127
Washer, Flat (5/16 x 5/8 x 1/16") 1 328
Screw, Hex Head Cap w/ Patch (5/16-18 x 1/2") 1 329
A - Includes items 14-18
B - Includes items 20-23
C - Includes items 27-29
NOTE:
Recline Only (2GR) with TRBKTS Option
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
12
Base Frame Interface Hardware (RWD)
Tilt Only (2GT) and Tilt/Recline (2GTR)
Form No.
99-150
13
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (RWD)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1082778 Actuator, Tilt - For All User Weight Limits 1 11 B
1026158 Locknut (5/16-18) 1 42
1031665 Screw, Socket Head Shoulder (3/8 x 1-1/2") 1 23
1082873 Pivot Assembly, Rear 1 14
1082760 Guidance Assembly, Linear 1 25
1117326 Screw, Socket Head Cap w/ Patch (5/16-18 x 7/8") 1 46
1091869 Screw, Socket Flat Head C'sunk with Patch (1/4-20
x 3/4")
1 67
1082877 Bar, Clamp, Black 1 28
1070398 Screw, Hex Head (5/16-18 x 1-1/2") 1 29
1039655 Bushing, Rubber 1 210
1070462 Screw, Hex Head Cap w/ Patch (5/16-18 x 7/8") 1 611
1082872 Bracket, Pivot, Front, Black 1 112 A
1086944 Screw, Socket Head Cap (5/16-18 x 3/4") 1 413
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 514
1082880 Support, Seat 1 215
1069724 T-Nut (5/16-18) 1 616
P0870X000 Nut, Hex Keps (#4-40) 1 217
1070430 Bracket, Charger Connector, Black 1 118
7930318 Screw, Phillips Pan Head (#4-40 x 1/2") 25 119
1070411 Bolt, Shoulder (3/8 x 2-1/2") 1 220
1098646 Bushing, Black (7/16 x 1/2 x 11/16") 1 221
1098645 Block, Black Tilt Angle 1 222
1140059 Kit, Actuator Braking Module w/ Instruction Sheet 1 123 C
1141508 Instruction Sheet, Actuator Braking Module 1 1D
A - Front pivot bracket made before 5/20/02 is no longer available. For seating systems manufactured before 5/20/02, see
Front Pivot Bracket and Links Kit page and order Kit part number 1112693.
B - Actuator Braking Module added to Tilt Actuator and is backward compatible to all systems made before 5/18/06. The
addition of the braking module eliminated the requirement of a Heavy Duty Tilt Actuator.
C - Actuator Braking Module can be assembled in the field on seating systems before 5/18/06 as well. Must verify with an
Invacare Technician when a kit is required.
D - Not Shown
NOTE:
Tilt Only (2GT) and Tilt/Recline (2GTR)
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
14
Base Frame Interface Hardware (RWD)
Tilt Only (2GT) and Tilt/Recline (2GTR) with TRBKTS Option
Form No.
99-150
15
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (RWD)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1082778 Actuator, Tilt - For All User Weight Limits 1 11 D
1026158 Locknut (5/16-18) 1 42
1031665 Screw, Socket Head Shoulder (3/8 x 1-1/2") 1 23
1082873 Pivot Assembly, Rear 1 14
1082760 Guidance Assembly, Linear 1 25
1117326 Screw, Socket Head Cap w/ Patch (5/16-18 x 7/8") 1 46
1091869 Screw, Socket Flat Head C'sunk with Patch (1/4-20
x 3/4")
1 67
1082877 Bar, Clamp, Black 1 28
1070462 Screw, Hex Head Cap w/ Patch (5/16-18 x 7/8") 1 49
1082872 Bracket, Pivot, Front, Black 1 110
1021344 Screw, Socket Head Cap (5/16-18 x 1-1/2") 1 411
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 612
1082880 Support, Seat 1 213
1140342 Spacer, Seat Support Mounting 1 214
1069724 T-Nut (5/16-18) 1 615
1043627 Screw, Hex Head Cap with Patch (5/16-18 x 1-3/4") 1 216
1070430 Bracket, Charger Connector, Black 1 117
1140259 Kit, Front/Rear Tie-Down Brackets Mounting
Hardware
1 118 A
Screw, Hex Head (5/16-18 x 3/4") 1 419
Washer, Flat (5/16 x 5/8 x 1/16") 1 420
T-Nut (5/16-18) 1 421
Screw, Socket Head Cap with Patch (5/16-18 x
1-3/4")
1 422
Screw, Socket Head Cap (3/8-16 x 3/4") 1 223
1140263 Kit, Top Battery Support Bracket and Mounting
Hardware
1 124 B
Bracket, Top Battery Support 1 125
Washer, Flat (5/16 x 5/8 x 1/16") 1 726
Screw, Hex Head (5/16-18 x 5/8") 1 327
Screw, Hex Head Cap with Patch (5/16-18 x 3/4") 1 428
T-Nut (5/16-18) 1 429
1135963 Bracket, Battery Support, Black 1 130
1140260 Kit, Front Battery Support Bracket with Mounting
Hardware
1 131 C
Bracket, Battery Support, Black - Front 1 132
Washer, Flat (5/16 x 5/8 x 1/16") 1 333
Screw, Hex Head Cap w/ Patch (5/16-18 x 1/2") 1 334
1140059 Kit, Actuator Braking Module w/ Instruction Sheet 1 135 E
1141508 Instruction Sheet, Actuator Braking Module 1 1F
Tilt Only (2GT) and Tilt/Recline (2GTR) with TRBKTS Option
Form No.
99-150
16
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (RWD)
A - Includes items 19-23
B - Includes items 25-28
C - Includes items 32-34
D - Actuator Braking Module added to Tilt Actuator and is backward compatible to all systems manufactured before 5/18/06.
The addition of the braking module eliminated the requirement of a Heavy Duty Tilt Actuator.
E - Actuator Braking Module can be assembled in the field on seating systems manufactured before 5/18/06 as well. Must
verify with an Invacare Technician when a kit is required.
F - Not Shown
NOTE:
Tilt Only (2GT) and Tilt/Recline (2GTR) with TRBKTS Option
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
17
Base Frame Interface Hardware (FWD)
Tilt Only (2GT) and Tilt/Recline (2GTR)
Form No.
99-150
18
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware (FWD)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1082778 Actuator, Tilt - For All User Weight Limits 1 11 B
1026158 Locknut (5/16-18) 1 42
1031665 Screw, Socket Head Shoulder (3/8 x 1-1/2") 1 23
1082873 Pivot Assembly, Rear 1 14
1082760 Guidance Assembly, Linear 1 25
1117326 Screw, Socket Head Cap w/ Patch (5/16-18 x 7/8") 1 46
1091869 Screw, Socket Flat Head C'sunk with Patch (1/4-20
x 3/4")
1 67
1082877 Bar, Clamp, Black 1 28
1074133 Washer (5/16 x 3/4 x 1/16") 1 29
7930337 Screw, Hex Head Cap with Patch (5/16-18 x 1-1/4") 25 110
1095481 Plate, Wedge 1 211
1095479 Wedge, Seat Mounting 1 212
1086944 Screw, Socket Head Cap (5/16-18 x 3/4") 1 613
1061922 Screw, Hex Head Cap w/ Patch (5/16-18 x 1/2") 1 414
1082872 Bracket, Pivot, Front, Black 1 115 A
1039655 Bushing, Rubber 1 216
1070398 Screw, Hex Head (5/16-18 x 1-1/2") 1 217
1069724 T-Nut (5/16-18) 1 418
1070411 Bolt, Shoulder (3/8 x 2-1/2") 1 219
1098646 Bushing, Black (7/16 x 1/2 x 11/16") 1 220
1098645 Block, Black Tilt Angle 1 221
1140059 Kit, Actuator Braking Module w/ Instruction Sheet 1 122 C
1141508 Instruction Sheet, Actuator Braking Module 1 1D
A - Front pivot bracket made before 5/20/02 is no longer available. For seating systems manufactured before 5/20/02, see
Front Pivot Bracket and Links Kit page and order Kit part number 1112693.
B - Actuator Braking Module added to Tilt Actuator and is backward compatible to all systems manufactured before 5/18/06.
The addition of the braking module eliminated the requirement of a Heavy Duty Tilt Actuator.
C - Actuator Braking Module can be assembled in the field on seating systems manufactured before 5/18/06 as well. Must
verify with an Invacare Technician when a kit is required.
D - Not Shown
NOTE:
Tilt Only (2GT) and Tilt/Recline (2GTR)
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
19
Base Frame Interface Hardware
Recline Only (2GR)
Form No.
99-150
20
To order call toll free 1-800-333-6900, or www.invacare.com
Base Frame Interface Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1082873 Pivot Assembly, Rear 1 11
1030949 Screw, Hex Head (1/4-20 x 1-1/2") 1 62
1086943 Bar, Spacer, Black 1 23
1095481 Plate, Wedge 1 24
1086944 Screw, Socket Head Cap (5/16-18 x 3/4") 1 65
1095479 Wedge, Seat Mounting 1 26
1074133 Washer (5/16 x 3/4 x 1/16") 1 27
7930337 Screw, Hex Head Cap with Patch (5/16-18 x 1-1/4") 25 18
1061922 Screw, Hex Head Cap w/ Patch (5/16-18 x 1/2") 1 49
1082872 Bracket, Pivot, Front, Black 1 110 A
1069724 T-Nut (5/16-18) 1 411
A - Front pivot bracket made before 5/20/02 is no longer available. For seating systems manufactured before 5/20/02, see
Front Pivot Bracket and Links Kit page and order Kit part number 1112693.
NOTE:
Recline Only (2GR)
Form No.
99-150
21
To order call toll free 1-800-333-6900, or www.invacare.com
Side Frames
NOTE: A new cross beam may be required when changing seat width for a Recline Only or Tilt/Recline
system. See center seat frame assembly page.
Form No.
99-150
22
To order call toll free 1-800-333-6900, or www.invacare.com
Side Frames
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1087002 Hardware, Side Frame Mounting 1 11 A
7930333 Locknut (1/4-20) 25 12
1047449 Spacer (1/4 x 3/8 x 3/16") 1 43
1026099 Spacer, Coved (1/4 x 11/16 x 1/2") 1 44
1037610 Screw, Hex Head (1/4-20 x 1-5/8") 1 45
1086976 Side Frame w/ Arm Lock Assembly, 16"-17" Deep,
Right
1 16
1086977 Side Frame w/ Arm Lock Assembly, 16"-17" Deep,
Left
1 16
1086978 Side Frame w/ Arm Lock Assembly, 18"-19" Deep,
Right
1 16
1086979 Side Frame w/ Arm Lock Assembly, 18"-19" Deep,
Left
1 16
1086980 Side Frame w/ Arm Lock Assembly, 20"-21" Deep,
Right
1 16
1086981 Side Frame w/ Arm Lock Assembly, 20"-21" Deep,
Left
1 16
1086982 Side Frame w/ Arm Lock Assembly, 22" Deep, Right 1 16
1086983 Side Frame w/ Arm Lock Assembly, 22" Deep, Left 1 16
7930347 Pin Roll (5/64 x 5/8") 25 17 B
47471X074 Spring, Arm Lock 1 27 B
1028594 Pin, Arm Lock 1 27 B
1090768 Kit, Lock Handle w/Rivets (both LT & RT side) 2 17 B
A - Includes Items 2-5
B - Arm Lock Assembly
NOTE:
NOTE: A new cross beam may be required when changing seat width for a Recline Only or Tilt/Recline
system. See center seat frame assembly page.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
23
Center Seat Frame Attaching Hardware
(RWD and FWD)
Form No.
99-150
24
To order call toll free 1-800-333-6900, or www.invacare.com
Center Seat Frame Attaching Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1026158 Locknut (5/16-18) 1 41
1031665 Screw, Socket Head Shoulder (3/8 x 1-1/2") 1 42
1070411 Bolt, Shoulder (3/8 x 2-1/2") 1 23
1098646 Bushing, Black (7/16 x 1/2 x 11/16") 1 24
1098645 Block, Black Tilt Angle 1 25
(RWD and FWD)
Form No.
99-150
25
To order call toll free 1-800-333-6900, or www.invacare.com
Center Seat Frame Assembly
Tilt Only (2GT)
Form No.
99-150
26
To order call toll free 1-800-333-6900, or www.invacare.com
Center Seat Frame Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1087010 Center Seat Frame Assembly, Short (16"-19" Deep) 1 11 A
1087011 Center Seat Frame Assembly, Long (20"-22" Deep) 1 11 A
1082874 Center Seat Frame, Short (16"-19" Deep) 1 12
1082875 Center Seat Frame, Long (20"-22" Deep) 1 12
1086590 Tilt Pivot Assembly, Right 1 13
1086591 Tilt Pivot Assembly, Left 1 13
1012371 Washer, Nylon (3/8 x 7/8 x 1/16") 1 84
1061922 Screw, Hex Head Cap w/ Patch (5/16-18 x 1/2") 1 25
1082876 Spacer (3/8 x 3/4 x 3/8") 1 26
1086595 Link, Tilt 1 27
1065214 Washer, Flat (3/8 x 11/16 x 1/16") 1 48
1086930 Ring, Retaining (3/8") 1 49
1091502 Guide, Tilt Rail 1 410
A - Includes Items 2-10
NOTE:
Tilt Only (2GT)
Form No.
99-150
27
To order call toll free 1-800-333-6900, or www.invacare.com
Center Seat Frame Assembly
Recline Only (2GR)
Form No.
99-150
28
To order call toll free 1-800-333-6900, or www.invacare.com
Center Seat Frame Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1086944 Screw, Socket Head Cap (5/16-18 x 3/4") 1 61
1082878 Bracket, Screw Support Acutator, Right 1 12
1082879 Bracket, Screw Support Acturator, Left 1 12
1026158 Locknut (5/16-18) 1 73
1031665 Screw, Socket Head Shoulder (3/8 x 1-1/2") 1 14
1082750 Actuator, Recline 1 15
1012371 Washer, Nylon (3/8 x 7/8 x 1/16") 1 146
1087022-NLA Link, Recline, Right 1 17 A,A1,B
1087023-NLA Link, Recline, Left 1 17 A,A1,B
1110497 Link, Recline 0 and 5 Degree Seat Tilt, Right 1 17 C
1110498 Link, Recline 0 and 5 Degree Seat Tilt, Left 1 17 C
1110499 Link, Recline 10 and 15 Degree Seat Tilt, Right 1 17 C
1110500 Link, Recline 10 and 15 Degree Seat Tilt, Left 1 17 C
1065214 Washer, Flat (3/8 x 11/16 x 1/16") 1 48
1086930 Ring, Retaining (3/8") 1 49
1082876 Spacer (3/8 x 3/4 x 3/8") 1 210
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 211
1079203 Decal, Warning Pinch Point 1 212
1091500 Kit, Connecting Slide Bracket w/ Decal, Black -
Right
1 113
1091501 Kit, Connecting Slide Bracket w/ Decal, Black - Left 1 113
1098944 Screw, Socket Head Cap w/ Patch (1/4-20 x 3/4") 1 414
1095352 Block, Gear Hold Down Upper 1 215
1091503 Bushing (1/4 x 1/2 x 7/16") 1 416
1026035 Locknut (#10-24) 1 417
1000212 Screw, Shoulder (1/4 x 1-1/4") 1 418
1095476 Assembly, Dual Roller Right 1 119 D
1095477 Assembly, Dual Roller Left 1 119 D
A - Front pivot bracket made before 5/20/02 is no longer available. For seating systems manufactured before 5/20/02, see
Front Pivot Bracket and Links Kit page and order Kit part number 1112693.
A1 - To maintain an existing, 5, 10, or 15 degree seat tilt, only recline links made after 5/19/02 are required.
B - Before 5/20/02
C - After 5/19/02
D - Includes 2 each of items 16-18
NOTE:
Recline Only (2GR)
Form No.
99-150
29
To order call toll free 1-800-333-6900, or www.invacare.com
Center Seat Frame Assembly
Tilt/Recline (2GTR)
Form No.
99-150
30
To order call toll free 1-800-333-6900, or www.invacare.com
Center Seat Frame Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1086944 Screw, Socket Head Cap (5/16-18 x 3/4") 1 61
1082878 Bracket, Screw Support Acutator, Right 1 12
1082879 Bracket, Screw Support Acturator, Left 1 12
1026158 Locknut (5/16-18) 1 73
1031665 Screw, Socket Head Shoulder (3/8 x 1-1/2") 1 14
1082750 Actuator, Recline 1 15
1012371 Washer, Nylon (3/8 x 7/8 x 1/16") 1 86
1086595 Link, Tilt 1 27
1065214 Washer, Flat (3/8 x 11/16 x 1/16") 1 48
1086930 Ring, Retaining (3/8") 1 49
1082876 Spacer (3/8 x 3/4 x 3/8") 1 210
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 211
1079203 Decal, Warning Pinch Point 1 212
1091500 Kit, Connecting Slide Bracket w/ Decal, Black -
Right
1 113
1091501 Kit, Connecting Slide Bracket w/ Decal, Black - Left 1 113
1098944 Screw, Socket Head Cap w/ Patch (1/4-20 x 3/4") 1 414
1095352 Block, Gear Hold Down Upper 1 215
1091503 Bushing (1/4 x 1/2 x 7/16") 1 416
1026035 Locknut (#10-24) 1 417
1000212 Screw, Shoulder (1/4 x 1-1/4") 1 418
1095476 Assembly, Dual Roller Right 1 119 A
1095477 Assembly, Dual Roller Left 1 119 A
A - Includes 2 each of items 16-18
NOTE:
Tilt/Recline (2GTR)
Form No.
99-150
31
To order call toll free 1-800-333-6900, or www.invacare.com
Front Pivot Bracket and Links Kit
For Seating Systems Manufactured Before 5/20/02
NOTE: To know when a front pivot bracket made before 5/20/02 has already been replaced, ask the
Customer to verify if the support stop brackets that mount the rubber bushings are missing. See
comparison in detail "A" shown.
Form No.
99-150
32
To order call toll free 1-800-333-6900, or www.invacare.com
Front Pivot Bracket and Links Kit
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1112693 Kit, Front Pivot Bracket and Links 1 11 A
Bracket, Pivot, Front, Black 1 12
Bolt, Shoulder (3/8 x 2-1/2") 1 23
Bushing, Black (7/16 x 1/2 x 11/16") 1 24
Block, Black Tilt Angle 1 25
Locknut (5/16-18) 1 26
Washer, Flat (3/8 x 11/16 x 1/16") 1 27
Ring, Retaining (3/8") 1 28
Link, Recline 0 and 5 Degree Seat Tilt, Right 1 19
Link, Recline 0 and 5 Degree Seat Tilt, Left 1 19
Link, Recline 10 and 15 Degree Seat Tilt, Right 1 19
Link, Recline 10 and 15 Degree Seat Tilt, Left 1 19
Instuction Sheet, Replacing Front Pivot or Obtaining
0 degree Seat Tilt on Recline Only
1 1
A - Kit includes items 2-9 and the instruction sheet that is not shown. Kit is used for seating systems manufactured before
5/20/02.
NOTE:
For Seating Systems Manufactured Before 5/20/02
NOTE: To know when a front pivot bracket made before 5/20/02 has already been replaced, ask the
Customer to verify if the support stop brackets that mount the rubber bushings are missing. See
comparison in detail "A" shown.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
33
21"Depth 22"Depth16"Depth 17"Depth 18"Depth 19"Depth 20"Depth
106606810660571066046106603510660241066013109008316"Width
106606910660581066047106603610660251066014109008417"Width
106607010660591066048106603710660261066015109008518"Width
106607110660601066049106603810660271066016109008619"Width
106607210660611066050106603910660281066017109008720"Width
106607310660621066051106604010660291066018109008821"Width
106607410660631066052106604110660301066019109008922"Width
Seat Pan
Form No.
99-150
34
To order call toll free 1-800-333-6900, or www.invacare.com
Seat Pan Mounting Hardware
Form No.
99-150
35
To order call toll free 1-800-333-6900, or www.invacare.com
Seat Pan Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1092303 Hardware, Seat Pan Mounting 1 11 A
1030949 Screw, Hex Head (1/4-20 x 1-1/2") 1 42
1037610 Screw, Hex Head (1/4-20 x 1-5/8") 1 13
1026099 Spacer, Coved (1/4 x 11/16 x 1/2") 1 14
1025736 Locknut (1/4-20) 1 55
1047449 Spacer (1/4 x 3/8 x 3/16") 1 46
1026900 Washer (1/4 x 23/32 x 1/16") 1 17
A - Includes Items 2-7
NOTE:
Form No.
99-150
36
To order call toll free 1-800-333-6900, or www.invacare.com
Back Cane and Spreader Bar Assembly
Tilt Only (2GT)
NOTE: When changing back cane heights, new back assembly attaching hardware may be required.
Form No.
99-150
37
To order call toll free 1-800-333-6900, or www.invacare.com
Back Cane and Spreader Bar Assembly
#1 Spreader Bar
16"W 22"W17"W 18"W 19"W 20"W 21"W
1086107108610610861051086104108610310861021086101
#2 Back Canes
Back Height
20-21"H 22-23"H 24-25"H 26-27"H 28"H
10869561086954108695210869501086948Right
10869571086955108695310869511086949Left
NOTE: Chairs manufactured between November 2, 1999 and January 31, 2002 were subject to a field correction. Contact your Dealer to
make sure this has been done.
Tilt Only (2GT)
NOTE: When changing back cane heights, new back assembly attaching hardware may be required.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
38
Back Cane and Spreader Bar Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Spreader Bar 1 11
See Chart #2 Back Canes 1 22
1078214 Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2") 1 43
1026907 Washer (1/4 x 1/2 x 1/16") 1 44
1082699 T-Nut (1/4-20) 1 45
1099540 Link, Curve Tilt, Right 1 16 D,D1
1099541 Link, Curved Tilt, Left 1 16 D,D1
1031673 Washer, Nylon (35/64 x 1 x 1/16") 1 27
1099527 Screw, Socket Head Cap (3/8-16 x 3/4") 1 28 D,D1
1021851 Screw, Socket Head Shoulder (1/2 x 1-1/2") 1 29
1062604 Screw, Shoulder Socket Head (3/8 x 1-1/4") 1 210
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 611
1070398 Screw, Hex Head (5/16-18 x 1-1/2") 1 212
1082725 Block, Slide 1 213
1082724 Rod, Slide 1 214
1039860 Screw, Hex Head Cap with Patch (5/16-18 x 3/4") 1 215
1087014 Bracket, Connecting, Black - Right 1 116
1087015 Bracket, Connecting, Black - Left 1 116
1026158 Locknut (5/16-18) 1 417
40363X000 Hex Nut (3/8"-16) 1 418
1082829 Cap, Back Cane End 1 219
1099949 Curved Tilt Link Upgrade Kit 2 120 C
1098332 Instruction Sheet, Curved Link Upgrade Kit 1 1A
A - Not Shown
C - Includes Items 6-9, 18 and Instruction Sheet
D - Curved tilt link design changed along with (item 8) screw and removal of two washers as of 6/26/00. This change prevents
interference with flip back armrest. It is recommended that (item 20) curved tilt link upgrade kit be ordered for tilt systems
made
D1 - before 6/26/00.
NOTE:
Tilt Only (2GT)
NOTE: When changing back cane heights, new back assembly attaching hardware may be required.
39
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
(7/8" Round) Back Cane and Spreader Bar Assembly
Tilt Only (2GT)
Form No.
99-150
40
To order call toll free 1-800-333-6900, or www.invacare.com
(7/8" Round) Back Cane and Spreader Bar Assembly
Item #1 Spreader Bar
16"W 22"W17"W 18"W 19"W 20"W 21"W
0014202001410200140020013902001380200137020013602
Item #2 Back Canes
Back Height
Side 20-21"H 22-23"H 24-25"H 26"H
110473011047281104726
1103008
Right
See Note(s) A
110473111047291104727
1103009
Left
See Note(s) A
A - Due to a manufacturing change, 20" and 21" back height canes are made approximately 3" shorter for systems made 9/17/01.
Back canes must be ordered in pairs to prevent one cane from being shorter than the other for systems made before 9/18/01.
NOTE:
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Spreader Bar 1 11
See Chart #2 Back Canes 1 22
1086460 Foam Hand Grip (4-1/2" Long) 1 23
0190722 Half Clamp, Un-Threaded Holes
(7/8" Dia. Back Canes)
1 24
0190822 Half Clamp, Threaded Holes
(7/8" Dia. Back Canes)
1 25
1007219 Screw, Socket Head Cap (1/4-20 x 3/4") 1 66
1099540 Link, Curve Tilt, Right 1 17
1099541 Link, Curved Tilt, Left 1 17
1031673 Washer, Nylon (35/64 x 1 x 1/16") 1 28
1099527 Screw, Socket Head Cap (3/8-16 x 3/4") 1 29
1021851 Screw, Socket Head Shoulder (1/2 x 1-1/2") 1 210
1062604 Screw, Shoulder Socket Head (3/8 x 1-1/4") 1 211
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 612
1070398 Screw, Hex Head (5/16-18 x 1-1/2") 1 213
1082725 Block, Slide 1 214
1082724 Rod, Slide 1 215
1039860 Screw, Hex Head Cap with Patch (5/16-18 x 3/4") 1 216
1087014 Bracket, Connecting, Black - Right 1 117
1087015 Bracket, Connecting, Black - Left 1 117
1026158 Locknut (5/16-18) 1 418
40363X000 Hex Nut (3/8"-16) 1 419
Tilt Only (2GT)
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
41
Back Cane and Spreader Bar Assembly
Recline Only (2GR) and Tilt/ Recline (2GTR)
NOTE: When changing back cane heights, new back assembly attaching hardware may be required.
Form No.
99-150
42
To order call toll free 1-800-333-6900, or www.invacare.com
Back Cane and Spreader Bar Assembly
#1 Spreader Bar
16"W 22"W17"W 18"W 19"W 20"W 21"W
1086107108610610861051086104108610310861021086101
#2 Back Canes
Back Height
20-21"H 22-23"H 24-25"H 26-27"H 28"H
10869561086954108695210869501086948Right
10869571086955108695310869511086949Left
NOTE: Chairs manufactured between November 2, 1999 and January 31, 2002 were subject to a field correction. Contact your Dealer to
make sure this has been done.
Recline Only (2GR) and Tilt/ Recline (2GTR)
NOTE: When changing back cane heights, new back assembly attaching hardware may be required.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
43
Back Cane and Spreader Bar Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Spreader Bar 1 11
See Chart #2 Back Canes 1 22
1078214 Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2") 1 43
1026907 Washer (1/4 x 1/2 x 1/16") 1 44
1082699 T-Nut (1/4-20) 1 45
1086587 Link, Curved 1 26 C
1031673 Washer, Nylon (35/64 x 1 x 1/16") 1 47
1086323 Screw, Socket Head Shoulder (1/2 x 5/8") 1 28
1021851 Screw, Socket Head Shoulder (1/2 x 1-1/2") 1 29
1062604 Screw, Shoulder Socket Head (3/8 x 1-1/4") 1 210
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 611
1070398 Screw, Hex Head (5/16-18 x 1-1/2") 1 212
1082725 Block, Slide 1 213
1082724 Rod, Slide 1 214
1039860 Screw, Hex Head Cap with Patch (5/16-18 x 3/4") 1 215
1026158 Locknut (5/16-18) 1 416
40363X000 Hex Nut (3/8"-16) 1 417
1065214 Washer, Flat (3/8 x 11/16 x 1/16") 1 218
1082829 Cap, Back Cane End 1 219
1099948 Kit, Curved Link Upgrade, 2GR and 2GTR 2 120 B
1087001 Kit, Back Cane and Spreader Bar Mounting
Hardware
2 121 D
1098332 Instruction Sheet, Curved Link Upgrade Kit 1 1A
A - Not Shown
B - Includes Items 6-9, 17, 18 and Instruction Sheet
C - Due to product improvement the curved link changed from aluminum to steel as of 3/20/00. It is recommended that (item
20) curved link upgrade kit be ordered for systems made before 3/20/00.
D - Includes items 3-19
NOTE:
Recline Only (2GR) and Tilt/ Recline (2GTR)
NOTE: When changing back cane heights, new back assembly attaching hardware may be required.
44
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
45
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
46
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
#1 Back Pan 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
108603110860301086029108602813"20"
108603810860371086036108603514"21"
108604510860441086043108604215"22"
108605210860511086050108604916"23"
108605910860581086057108605617"24"
108606610860651086064108606318"25"
108607310860721086071108607019"26"
108608010860791086078108607720"27"
108608710860861086085108608421"28"
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
47
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
#1 Back Pan 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10860341086033108603213"20"
10860411086040108603914"21"
10860481086047108604615"22"
10860551086054108605316"23"
10860621086061108606017"24"
10860691086068108606718"25"
10860761086075108607419"26"
10860831086082108608120"27"
10860901086089108608821"28"
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
48
A.B.S. Curved Back w/o Attaching Hardware
#2 Back Cushion Assembly 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109738510973841097383109738213"20"
109739210973911097390109738914"21"
109739910973981097397109739615"22"
109740610974051097404109740316"23"
109741310974121097411109741017"24"
109742010974191097418109741718"25"
109742710974261097425109742419"26"
109743410974331097432109743120"27"
109744110974401097439109743821"28"
Back cover and foam are sold as a back cushion assembly only.
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
49
A.B.S. Curved Back w/o Attaching Hardware
#2 Back Cushion Assembly 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10973881097387109738613"20"
10973951097394109739314"21"
10974021097401109740015"22"
10974091097408109740716"23"
10974161097415109741417"24"
10974231097422109742118"25"
10974301097429109742819"26"
10974371097436109743520"27"
10974441097443109744221"28"
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
50
A.B.S. Curved Back w/o Attaching Hardware
#3 Back Assembly w/o Hardware 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109057810905771090576109057513"20"
109058510905841090583109058214"21"
109059210905911090590109058915"22"
109059910905981090597109059616"23"
109060610906051090604109060317"24"
109061310906121090611109061018"25"
109062010906191090618109061719"26"
109062710906261090625109062420"27"
109063410906331090632109063121"28"
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
51
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
#3 Back Assembly w/o Hardware 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10905811090580109057913"20"
10905881090587109058614"21"
10905951090594109059315"22"
10906021090601109060016"23"
10906091090608109060717"24"
10906161090615109061418"25"
10906231090622109062119"26"
10906301090629109062820"27"
10906371090636109063521"28"
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
52
A.B.S. Curved Back w/o Attaching Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Back Pan 16" Wide - 19" Wide 1 11
See Chart #1 Back Pan 20" Wide - 22" Wide 1 11
See Chart #2 Back Cushion Assembly 16" Wide - 19" Wide 1 12
See Chart #2 Back Cushion Assembly 20" Wide - 22" Wide 1 12
See Chart #3 Back Assembly w/o Hardware 16" Wide - 19"
Wide
1 13
See Chart #3 Back Assembly w/o Hardware 20" Wide - 22"
Wide
1 13
1125723 Kit, Hook Fastener w/ Adhesive Back 1 1A
A - Not Shown. Hook Fastener Adhesive Kit is used to attach the Back Cover to the Back Pan and must be ordered when a
new Back Pan or Back Assembly is requested.
NOTE:
Tilt Only (2GT)
(Before 11/1/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 6-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
53
A.B.S. Curved Back w/o Attaching Hardware
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
54
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
55
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
#1 Back Pan 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
108605210860511086050108604916"20"
108605910860581086057108605617"21"
108606610860651086064108606318"22"
108607310860721086071108607019"23"
108608010860791086078108607720"24"
108608710860861086085108608421"25"
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
56
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
#1 Back Pan 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10860551086054108605316"20"
10860621086061108606017"21"
10860691086068108606718"22"
10860761086075108607419"23"
10860831086082108608120"24"
10860901086089108608821"25"
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
57
A.B.S. Curved Back w/o Attaching Hardware
#2 Back Cushion Assembly 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109740610974051097404109740316"20"
109741310974121097411109741017"21"
109742010974191097418109741718"22"
109742710974261097425109742419"23"
109743410974331097432109743120"24"
109744110974401097439109743821"25"
Back cover and foam are sold as a back cushion assembly only.
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
58
A.B.S. Curved Back w/o Attaching Hardware
#2 Back Cushion Assembly 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10974091097408109740716"20"
10974161097415109741417"21"
10974231097422109742118"22"
10974301097429109742819"23"
10974371097436109743520"24"
10974441097443109744221"25"
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
59
A.B.S. Curved Back w/o Attaching Hardware
#3 Back Assembly w/o Hardware 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109059910905981090597109059616"20"
109060610906051090604109060317"21"
109061310906121090611109061018"22"
109062010906191090618109061719"23"
109062710906261090625109062420"24"
109063410906331090632109063121"25"
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
60
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware
#3 Back Assembly w/o Hardware 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10906021090601109060016"20"
10906091090608109060717"21"
10906161090615109061418"22"
10906231090622109062119"23"
10906301090629109062820"24"
10906371090636109063521"25"
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
61
A.B.S. Curved Back w/o Attaching Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Back Pan 16" Wide - 19" Wide 1 11
See Chart #1 Back Pan 20" Wide - 22" Wide 1 11
See Chart #2 Back Cushion Assembly 16" Wide - 19" Wide 1 12
See Chart #2 Back Cushion Assembly 20" Wide - 22" Wide 1 12
See Chart #3 Back Assembly w/o Hardware 16" Wide - 19"
Wide
1 13
See Chart #3 Back Assembly w/o Hardware 20" Wide - 22"
Wide
1 13
1125723 Kit, Hook Fastener w/ Adhesive Back 1 1A
A - Not Shown. Hook Fastener Adhesive Kit is used to attach the Back Cover to the Back Pan and must be ordered when a
new Back Pan or Back Assembly is requested.
NOTE:
Tilt Only (2GT)
(After 10/31/00)
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 3-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: After 10/31/00 spacing between the seat pan and the lower side of the back pan was decreased 3"
by adding 3" to the back pan material. Overall back height did not change.
NOTE: A.B.S. curved backs do not retrofit to the 7/8" round canes. Key slotted back canes and back
attaching hardware must be ordered.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
62
A.B.S. Curved Back w/o Attaching Hardware (Before
4/21/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 8-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly
Form No.
99-150
63
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware (Before
#1 Back Pan 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
108601710860161086015108601411"20"
108602410860231086022108602112"21"
108603110860301086029108602813"22"
108603810860371086036108603514"23"
108604510860441086043108604215"24"
108605210860511086050108604916"25"
108605910860581086057108605617"26"
108606610860651086064108606318"27"
108607310860721086071108607019"28"
4/21/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 8-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly
Form No.
99-150
64
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware (Before
#1 Back Pan 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10860201086019108601811"20"
10860271086026108602512"21"
10860341086033108603213"22"
10860411086040108603914"23"
10860481086047108604615"24"
10860551086054108605316"25"
10860621086061108606017"26"
10860691086068108606718"27"
10860761086075108607419"28"
4/21/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 8-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
65
A.B.S. Curved Back w/o Attaching Hardware (Before
#2 Back Cushion Assembly 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109737110973701097369109736811"20"
109737810973771097376109737512"21"
109738510973841097383109738213"22"
109739210973911097390109738914"23"
109739910973981097397109739615"24"
109740610974051097404109740316"25"
109741310974121097411109741017"26"
109742010974191097418109741718"27"
109742710974261097425109742419"28"
Back cover and foam are sold as a back cushion assembly only.
4/21/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 8-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
66
A.B.S. Curved Back w/o Attaching Hardware (Before
#2 Back Cushion Assembly 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10973741097373109737211"20"
10973811097380109737912"21"
10973881097387109738613"22"
10973951097394109739314"23"
10974021097401109740015"24"
10974091097408109740716"25"
10974161097415109741417"26"
10974231097422109742118"27"
10974301097429109742819"28"
4/21/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 8-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
67
A.B.S. Curved Back w/o Attaching Hardware (Before
#3 Back Assembly w/o Hardware 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109056410905631090562109056111"20"
109057110905701090569109056812"21"
109057810905771090576109057513"22"
109058510905841090583109058214"23"
109059210905911090590109058915"24"
109059910905981090597109059616"25"
109060610906051090604109060317"26"
109061310906121090611109061018"27"
109062010906191090618109061719"28"
4/21/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 8-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly
Form No.
99-150
68
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware (Before
#3 Back Assembly w/o Hardware 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10905671090566109056511"20"
10905741090573109057212"21"
10905811090580109057913"22"
10905881090587109058614"23"
10905951090594109059315"24"
10906021090601109060016"25"
10906091090608109060717"26"
10906161090615109061418"27"
10906231090622109062119"28"
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Back Pan 16" Wide - 19" Wide 1 11
See Chart #1 Back Pan 20" Wide - 22" Wide 1 11
See Chart #2 Back Cushion Assembly 16" Wide - 19" Wide 1 12
See Chart #2 Back Cushion Assembly 20" Wide - 22" Wide 1 12
See Chart #3 Back Assembly w/o Hardware 16" Wide - 19"
Wide
1 13
See Chart #3 Back Assembly w/o Hardware 20" Wide - 22"
Wide
1 13
1125723 Kit, Hook Fastener w/ Adhesive Back 1 1A
A - Not Shown. Hook Fastener Adhesive Kit is used to attach a Back Cover to the Back Pan and must be ordered when a new
Back Pan or Back Assembly is requested.
NOTE:
4/21/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 8-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
69
A.B.S. Curved Back w/o Attaching Hardware (After 4/20/03)
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 4-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
70
To order call toll free 1-800-333-6900, or www.invacare.com
A.B.S. Curved Back w/o Attaching Hardware (After 4/20/03)
#1 Back Pan 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
108604510860441086043108604215"20"
108605210860511086050108604916"21"
108605910860581086057108605617"22"
108606610860651086064108606318"23"
108607310860721086071108607019"24"
108608010860791086078108607720"25"
108608710860861086085108608421"26"
#1 Back Pan 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10860481086047108604615"20"
10860551086054108605316"21"
10860621086061108606017"22"
10860691086068108606718"23"
10860761086075108607419"24"
10860831086082108608120"25"
10860901086089108608821"26"
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 4-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
71
A.B.S. Curved Back w/o Attaching Hardware (After 4/20/03)
#2 Back Cushion Assembly 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109739910973981097397109739615"20"
109740610974051097404109740316"21"
109741310974121097411109741017"22"
109742010974191097418109741718"23"
109742710974261097425109742419"24"
109743410974331097432109743120"25"
109744110974401097439109743821"26"
Back cover and foam are sold as a back cushion assembly only.
#2 Back Cushion Assembly 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10974021097401109740015"20"
10974091097408109740716"21"
10974161097415109741417"22"
10974231097422109742118"23"
10974301097429109742819"24"
10974371097436109743520"25"
10974441097443109744221"26"
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 4-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
72
A.B.S. Curved Back w/o Attaching Hardware (After 4/20/03)
#3 Back Assembly w/o Hardware 16" Wide - 19" Wide
Overall
Back
Height
Material
Back
Height
16" W 17" W 18" W 19" W
109059210905911090590109058915"20"
109059910905981090597109059616"21"
109060610906051090604109060317"22"
109061310906121090611109061018"23"
109062010906191090618109061719"24"
109062710906261090625109062420"25"
109063410906331090632109063121"26"
#3 Back Assembly w/o Hardware 20" Wide - 22" Wide
Overall
Back
Height
Material
Back
Height
20" W 21" W 22" W
10905951090594109059315"20"
10906021090601109060016"21"
10906091090608109060717"22"
10906161090615109061418"23"
10906231090622109062119"24"
10906301090629109062820"25"
10906371090636109063521"26"
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 4-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
73
A.B.S. Curved Back w/o Attaching Hardware (After 4/20/03)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Back Pan 16" Wide - 19" Wide 1 11
See Chart #1 Back Pan 20" Wide - 22" Wide 1 11
See Chart #2 Back Cushion Assembly 16" Wide - 19" Wide 1 12
See Chart #2 Back Cushion Assembly 20" Wide - 22" Wide 1 12
See Chart #3 Back Assembly w/o Hardware 16" Wide - 19"
Wide
1 13
See Chart #3 Back Assembly w/o Hardware 20" Wide - 22"
Wide
1 13
1125723 Kit, Hook Fastener w/ Adhesive Back 1 1A
A - Not Shown. Hook Fastener Adhesive Kit is used to attach the Back Cover to the Back Pan and must be ordered when a
new Back Pan or Back Assembly is requested.
NOTE:
Recline Only (2GR) and Tilt/Recline (2GTR) w/ V.S.R.
NOTE: Overall back height is calculated by measuring from the seat pan surface to the top of the back
pan. Back pan material height can be calculated by subtracting 4-3/4" from the overall back height listed.
Material height listed is rounded off to the nearest whole number.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
74
Profile Back without Attaching Hardware
NOTE: See back mounting hardware under accessories when attaching a profile back to 7/8" round
canes.
Form No.
99-150
75
To order call toll free 1-800-333-6900, or www.invacare.com
Profile Back without Attaching Hardware
Back Material
Width x Height
Overall Back
Height - Tilt
Overall Back
Height - VSR
#1
Back Cover
#2
Back Assembly
w/o Sliding
Hardware
10918770276800-NLA25" H23" H16" x 16"
10918770276800-NLA25" H23" H17" x 16"
10918760276900-NLA25" H23" H18" x 16"
10918760276900-NLA25" H23" H19" x 16"
1091878027700025" H23" H20" x 16"
1091878027700025" H23" H21" x 16"
1091875027710026" H24" H16" x 18"
1091875027710026" H24" H17" x 18"
1091874027720026" H24" H18" x 18"
1091874027720026" H24" H19" x 18"
1091873027730026" H24" H20" x 18"
1091873027730026" H24" H21" x 18"
NOTE: See back mounting hardware under accessories when attaching a profile back to 7/8" round
canes.
Form No.
99-150
76
To order call toll free 1-800-333-6900, or www.invacare.com
Back Assembly Attaching Hardware
A.B.S. Curved and Profile
NOTE: Items 1, 2 and attaching hardware may be required when changing back styles or back cane
heights.
NOTE: See back mounting hardware under accessories when attaching a profile back to 7/8" round
canes.
Form No.
99-150
77
To order call toll free 1-800-333-6900, or www.invacare.com
Back Assembly Attaching Hardware
#1 Back Slide Block
Seating System
28"
Back Height
Back Type
20"-21"
Back Height
22"-23"
Back Height
24"-25"
Back Height
26"-27"
Back Height
10829191082918108291710829161082915Curved
Tilt Only
Before 11/1/00
10829151082915108291510829151082915ProfileTilt Only
10829181082917108291610829151082914Curved
Recline Only
and Tilt/Recline
w/VSR
10829151082915108291510829151082915Profile
Recline Only
and Tilt/Recline
w/VSR
#1 Back Slide Block (Tilt Only A.B.S. Curved After 10/31/00)
Seating System Back Type
20"
Back Height
21"-22"
Back Height
23"-24"
Back Height
25"
Back Height
1082919108291810829171082916Curved
Tilt Only
After 10/31/00
See Note(s) A
A - After 10/31/00 spacing between the seat pan and lower side of the back pan was decreased 3" by adding 3" to the back pan
material. Overall back height did not change.
NOTE:
#2 Back Slide Sleeve
Seating System
28"
Back Height
Back Type
20"-21"
Back Height
22"-23"
Back Height
24"-25"
Back Height
26"-27"
Back Height
10829471082946108294510829441082943CurvedTilt Only
10829431082943108294310829431082943ProfileTilt Only
10829461082945108294410829431082942Curved
Recline Only
and Tilt/Recline
w/ VSR
10829431082943108294310829431082943Profile
Recline Only
and Tilt/Recline
w/ VSR
A.B.S. Curved and Profile
NOTE: Items 1, 2 and attaching hardware may be required when changing back styles or back cane
heights.
NOTE: See back mounting hardware under accessories when attaching a profile back to 7/8" round
canes.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
78
Back Assembly Attaching Hardware
#2 Back Slide Sleeve (Tilt Only A.B.S. Curved After 10/31/00)
Seating System Back Type
20"
Back Height
21"-22"
Back Height
23"-24"
Back Height
25"
Back Height
1082947108294610829451082944Curved
Tilt Only
After 10/31/00
See Note(s) A
A - After 10/31/00 spacing between the seat pan and lower side of the back pan was decreased 3" by adding 3" to the back pan
material. Overall back height did not change.
NOTE:
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart #1 Back Slide Block 1 21
See Chart #1 Back Slide Block (Tilt Only A.B.S. Curved After
10/31/00)
1 21
See Chart #2 Back Slide Sleeve 1 22
See Chart #2 Back Slide Sleeve (Tilt Only A.B.S. Curved After
10/31/00)
1 22
1026907 Washer (1/4 x 1/2 x 1/16") 1 23
1000212 Screw, Shoulder (1/4 x 1-1/4") 1 24
1091870 Screw, Socket Button Head w/ Patch
(1/4-20 x 3/4")
1 45
1008432 Screw, Socket Button Head (1/4-20 x 1-1/4") 1 46 B
1091870 Screw, Socket Button Head w/ Patch
(1/4-20 x 3/4")
1 46 F
1090131 Spacer, Black (1/4 x 3/4 x 5/8") 1 47
1086994 Hardware, Attaching, A.B.S. Curved Back 1 1A,C
1086996 Hardware, Attaching, Profile Back (17",19",21"
Wide)
1 1A,D
1086995 Hardware, Attaching, Profile Back (16",18",20",22"
Wide)
1 1A,E
A - Not Shown
B - 17",19" and 21" Wide
C - Includes Items 3-5
D - Includes Items 3,4,6 and 7
E - Includes Items 3,4 and 6
F - 16",18", 20" and 22" Wide
NOTE:
A.B.S. Curved and Profile
NOTE: Items 1, 2 and attaching hardware may be required when changing back styles or back cane
heights.
NOTE: See back mounting hardware under accessories when attaching a profile back to 7/8" round
canes.
Form No.
99-150
79
To order call toll free 1-800-333-6900, or www.invacare.com
Back Assembly V.S.R. Actuator Motor & Attaching
Hardware
Recline Only (2GR) and Tilt/Recline (2GTR)
Form No.
99-150
80
To order call toll free 1-800-333-6900, or www.invacare.com
Back Assembly V.S.R. Actuator Motor & Attaching
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1121051 V.S.R. Actuator Mounting Hardware,
A.B.S. Curved Back
1 11 A
1121052 V.S.R. Actuator Mounting Hardware,
Profile Back
1 11 B
7930323 Package, Locknut (1/4-20) 25 12 C
7930326 Screw, Hex Head (1/4-20 x 3/4") 25 13 D
1121023 Bracket, V.S.R. Actuator Mounting 1 14
1026907 Washer (1/4 x 1/2 x 1/16") 1 25
0001100 Actuator Assembly, 5" Stroke 1 16 E
1113627 Actuator Assembly, 3" Stroke 1 16 F
1008495 Screw, Socket Button Head (1/4-20 x 1-1/2") 1 17
1091869 Screw, Socket Flat Head C'sunk with Patch (1/4-20
x 3/4")
1 28
A - Includes Items 2-5, 7 and 8
B - Includes Items 2-5 and 7
C - Profile Backs Use Quantity of 3 Only
D - Profile Backs Use Quantity of 3
E - A.B.S. Curved Backs before 4/21/03 and all Profile Backs
F - A.B.S. Curved Backs after 4/20/03
NOTE:
Hardware
Recline Only (2GR) and Tilt/Recline (2GTR)
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
81
Armrest Assembly
Tilt Only (2GT)
Form No.
99-150
82
To order call toll free 1-800-333-6900, or www.invacare.com
Armrest Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
8881011811 Arm Pad, Vinyl, Desk Length (9" L x 2" W) 1 11 A,C
8881053578 Arm Pads, Vinyl, Desk Length with Screws (9" L x
2" W)
2 11 A,C
8881015932 Arm Pad, Vinyl, Full Length (14" L x 2" W) - Right 1 11 A,C
8881015933 Arm Pad, Vinyl, Full Length (14" L x 2" W) - Left 1 11 A,C
8881053577 Arm Pads, Vinyl, Full Length with Screws (14" L x 2"
W)
2 11 A
1082910 Arm Pad w/ Elbow Stop, Desk, Black Urethane (13"
L x 3" W) - Right
1 11 B
1082911 Arm Pad w/ Elbow Stop, Desk, Black Urethane (13"
L x 3" W) - Left
1 11 B
1090190 Arm Pad w/ Elbow Stop, Desk, Black Urethane (13"
L x 3" W) - Pair w/ Screws
2 11 B
1082912 Arm Pad w/ Elbow Stop, Full, Black Urethane (17" L
x 3" W) - Right
1 11 B
1082913 Arm Pad w/ Elbow Stop, Full, Black Urethane (17" L
x 3" W) - Left
1 11
1090191 Arm Pad w/ Elbow Stop, Full, Black Urethane (17" L
x 3" W) -Pair w/ Screws
2 11 B
1071253 Arm Top, Adjustable Height with Plug Buttons - Full
Length (Black)
1 12
1070859 Arm Tube, Upper with Plug Buttons (Black) - Desk
Length
1 12
1027095 Plug Button, Black (7/8") 1 23
1055949 Screws, Phillips Pan Head (#10-32 x 1-1/8") 2 14 A
1107155 Screw, Phillips Pan Head Tap (#10-32 x 1-1/4") 1 24 B
1064130 Clothing Guard 1 15
47471X074 Spring, Arm Lock 1 16
1028594 Pin, Arm Lock 1 17
1032244 Grip, Foam Hand (9" Long) 1 18
1090768 Kit, Lock Handle w/Rivets (both LT & RT side) 2 19
1028645 Rivet 1 610
1065936 Plug, Pivot 1 211
1067734 Plug Button, Black (5/8") 1 212
1068416 Arm Base, Adjustable Height
16-19" Deep - Right (Black)
1 113
1068417 Arm Base, Adjustable Height
16-19" Deep - Left (Black)
1 113
1068418 Arm Base, Adjustable Height
20" and Deeper - Right (Black)
1 113
1068419 Arm Base, Adjustable Height
20" and Deeper - Left (Black)
1 113
1067761 Arm Base, 1" Lower, Adjustable Height
16-19" Deep - Right (Black)
1 113
Tilt Only (2GT)
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
83
Armrest Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1067762 Arm Base, 1" Lower, Adjustable Height
16-19" Deep - Left (Black)
1 113
1067755 Arm Base, 1" Lower, Adjustable Height
20" and Deeper - Right (Black)
1 113
1067756 Arm Base, 1" Lower, Adjustable Height
20" and Deeper - Left (Black)
1 113
1068039 Pin, Pull 1 114
1030949 Screw, Hex Head (1/4-20 x 1-1/2") 1 115
1068025 Clevis, Pivot 1 116
7930323 Package, Locknut (1/4-20) 25 117
1068488 Kit, Swingaway Armrest Mounting Hardware 1 118
1035065 Cover, Clothing Guard with Pocket - For Fixed
Height Desk Length & Adjustable Height Full/Desk
Length
1 119
A - Before 5/1/02
B - After 4/30/02
C - Specify U67 upholstery color when ordering.
NOTE:
Tilt Only (2GT)
Form No.
99-150
84
To order call toll free 1-800-333-6900, or www.invacare.com
Armrest Assembly
Recline Only (2GR) and Tilt/Recline (2GTR)
Form No.
99-150
85
To order call toll free 1-800-333-6900, or www.invacare.com
Armrest Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1082910 Arm Pad w/ Elbow Stop, Desk, Black Urethane (13"
L x 3" W) - Right
1 11
1082911 Arm Pad w/ Elbow Stop, Desk, Black Urethane (13"
L x 3" W) - Left
1 11
1090190 Arm Pad w/ Elbow Stop, Desk, Black Urethane (13"
L x 3" W) - Pair w/ Screws
2 11
1082912 Arm Pad w/ Elbow Stop, Full, Black Urethane (17" L
x 3" W) - Right
1 11
1082913 Arm Pad w/ Elbow Stop, Full, Black Urethane (17" L
x 3" W) - Left
1 11
1090191 Arm Pad w/ Elbow Stop, Full, Black Urethane (17" L
x 3" W) -Pair w/ Screws
2 11
1086992 Arm Assembly w/o Arm Pad, Desk Length - Right 1 12 A,H
1086993 Arm Assembly w/o Arm Pad, Desk Length - Left 1 12 A,H
1087012 Arm Assembly w/o Arm Pad, Full Length - Right 1 12 B,H
1087013 Arm Assembly w/o Arm Pad, Full Length - Left 1 12 B,H
1008432 Screw, Socket Button Head (1/4-20 x 1-1/4") 1 33
1026103 Washer, Nylon (1/4 x 1/2 x 1/32") 1 44
0028202 Extension Tube, Full Length 1 15
1027095 Plug Button, Black (7/8") 1 16
1107155 Screw, Phillips Pan Head Tap (#10-32 x 1-1/4") 1 27
1028755 Screw, Phillips Pan Head (#10-32 x 5/8") 1 18 D
1107155 Screw, Phillips Pan Head Tap (#10-32 x 1-1/4") 1 18 E
1079203 Decal, Warning Pinch Point 1 19
1115392 Support Tube w/ Warning Decal, Arm 1 110 F
1115393 Slide Tube, Adjustable 1 111 F
1082842 Plug, Arm, Black 1 112
7930333 Locknut (1/4-20) 25 113
1082927 Arm Tube 1 114
1009838 Screw, Socket Head (1/4-20 x 3/4") 1 115
1095437 Arm Pivot Assembly 1 116 I
1086990 Hardware, Arm Attaching 1 117 C
1082699 T-Nut (1/4-20) 1 218
1086932 Pivot, Back Arm 1 119
1078214 Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2") 1 220
1119268 Slide Tube/Arm Support Assembly (Pair) 2 1G
Recline Only (2GR) and Tilt/Recline (2GTR)
Form No.
99-150
86
To order call toll free 1-800-333-6900, or www.invacare.com
Armrest Assembly
A - Includes Items 3,4,6, and 9-16
B - Includes Items 3-6 and 8-16
C - Includes Items 18-20
D - Used for full length arms only
E - Used for desk length arms only
F - Item 10 and 11 tube length was changed and item 11 went from 5 to 6 adjustment holes revising the adjustable arm height
from 9"-13" to 11"-16". For systems made before 4/21/03, order slide tube/arm support assembly part number 1119268.
G - Not Shown. Assembly includes 2 ea. of item numbers 9, 10 and 11
H - When placing an order for item 2, you must specify as a note "For Tarsys 2GTR seating" or "For Formula TRE seating".
I - The Arm Pivot Assembly Pin faces down for the Tarsys 2GTR and faces up for the Formula TRE powered seating
NOTE:
Recline Only (2GR) and Tilt/Recline (2GTR)
Form No.
99-150
87
To order call toll free 1-800-333-6900, or www.invacare.com
Shroud Covers
Rear, Side, Lower Seat and V.S.R. Actuator
Form No.
99-150
88
To order call toll free 1-800-333-6900, or www.invacare.com
Shroud Covers
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1104883 Shroud Assembly w/ Hardware, Tilt Only 3G 1 11 A
1104884 Shroud Assembly w/ Hardware, Recline Only 3G 1 11 B
1104842 Shroud Assembly w/ Hardware, Tilt/ Recline 3G 1 11 B
1091872 Shroud Cover with Dual Lock Fasteners, V.S.R.
Actuator
1 12
2001682 Wrap, Tie (8") 1 23
1091311 Shroud Cover with Dual Lock Fasteners, Rear 1 14
1025729 Screw, Self Tapping Pan Head (#8-32 x 3/8") 1 45
1091314 Cover, Shroud Assembly w/ Decal, Side (Black
Only) Tilt Only, Right
1 16 C
1091315 Cover, Shroud Assembly w/ Decal, Side (Black
Only) Tilt Only, Left
1 16 C
1091316 Cover, Shroud Assembly w/ Decal, Side (Black
Only) Recline Only, Right
1 16 C
1091317 Cover, Shroud Assembly w/ Decal, Side (Black
Only) Recline Only, Left
1 16 C
1091312 Cover, Shroud Assembly w/ Decal, Side (Black
Only) Tilt/ Recline, Right
1 16 C
1091313 Cover, Shroud Assembly w/ Decal, Side (Black
Only) Tilt/ Recline, Left
1 16 C
1094275 Shroud Cover with Loop Fastener, Lower Seat 1 17
1092662 Package, Fasteners, Dual Lock 250 (1/2" Wide x
7/8" Long)
10 18
1087033 Decal, Side Shroud Cover, Tilt Only 1 29
1087034 Decal, Side Shroud Cover, Recline Only 1 29
1087032 Decal, Side Shroud Cover, Tilt/ Recline 1 29
1079246 Fastener, Loop Adhesive Back (1" W x 3" L) 1 210
A - Includes Items 4-7
B - Includes Items 2-7
C - Back Only
NOTE:
Rear, Side, Lower Seat and V.S.R. Actuator
Form No.
99-150
89
To order call toll free 1-800-333-6900, or www.invacare.com
Controller Shroud Covers
Form No.
99-150
90
To order call toll free 1-800-333-6900, or www.invacare.com
Controller Shroud Covers
NOTE: All controller shroud covers include mounting hardware.
NOTE: Controller shroud covers used on RWD models only.
NOTE: Two controllers are identified as one chair with joystick and seating system controllers.
Seating
System
Type
Item 5Item 1 Item 2 Item 2 Item 3 Item 4
1104822
11048391112684
1104841
11048411091310
See Note(s) A See Note(s) B
After
5/19/02
(with or
without
shock forks
and
short base)
w/ one
controller and
(GB motors
without
wheel locks)
After
5/19/02
(with or
without
shock forks
and
short base)
w/ one
controller and
4-pole motors
or (GB motors
w/ wheel locks)
After
5/19/02
(When
short base
and shock
forks were
introduced
together and
are present)
w/ two
controllers
After
7/15/01
to present
w/ two
controllers
7/16/01
thru
5/19/02
w/ one
controller
Before
7/16/01
w/ one
or two
controllers
2GT
N/AN/A
After
5/19/02
(When
short base
and shock
forks were
introduced
together and
are present)
w/ two
controllers
After
7/15/01
to present
w/ two
controllers
N/A
Before
7/16/01
w/ two
controllers
2GR or
2GTR
A - Two TrueTrack decals must be ordered when G/B motors are present for chairs made after 6/2/02.
B - Shroud cover includes the TrueTrack decals and loop fasteners.
NOTE:
NOTE: All controller shroud covers include mounting hardware.
NOTE: Controller shroud covers used on RWD models only.
NOTE: Two controllers are identified as one chair with joystick and seating system controllers.
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
91
Controller Shroud Covers
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart Controller Shroud Covers 1 11-5
1104706 Kit, Controller Shroud Mounting Hardware (Pair) 2 16 A
1070580 Washer, Nylon Retainer (1/4 x 1/2 x 1/32") 1 27
1070581 Washer, Nylon Cupped (9/32 x 19/32 x 3/32") 1 28
1093312 Spring, Torsion Ejector 1 29
1110508 Stud, Phillips Recess (1/4" Dia. x 1" Long) 1 210 B
1110509 Retainer, Stud (1/4" Turn) 1 211
1079246 Fastener, Loop Adhesive Back (1" W x 3" L) 1 212
1104799 Decal, TrueTrack 1 213
1092662 Package, Fasteners, Dual Lock 250 (1/2" Wide x
7/8" Long)
10 114
1028755 Screw, Phillips Pan Head (#10-32 x 5/8") 1 215
A - Includes items 7-11
B - Due to a hardware change, when item 10 is requested, refer to Item 6 for chairs manufactured before 2/21/02
NOTE:
Form No.
99-150
To order call toll free 1-800-333-6900, or www.invacare.com
92
Front Rigging Hanger Assembly
Sector, Pin and Genius Style
NOTE: Front rigging hanger assemblies and seat pans share the same mounting hardware, see Seat Pan
Mounting Hardware page.
Form No.
99-150
93
To order call toll free 1-800-333-6900, or www.invacare.com
Front Rigging Hanger Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1070356 Hanger Assembly, Front Rigging,
Pin Style - (12-21" Deep), Right
1 11 A
1070357 Hanger Assembly, Front Rigging,
Pin Style - (12-21" Deep), Left
1 11 A
1070358 Hanger Assembly, Front Rigging,
Pin Style - (22" Deep), Right
1 11 A
1070359 Hanger Assembly, Front Rigging,
Pin Style - (22" Deep), Left
1 11 A
1027097 Plug Button, Black (3/4") 1 12
1068435 Front Rigging Hanger Assembly,
Sector Style (12-21" Deep) - Right
1 13 B
1068436 Front Rigging Hanger Assembly,
Sector Style (12-21" Deep) - Left
1 13 B
1068437 Front Rigging Hanger Assembly,
Sector Style (22" Deep) - Right
1 13 B
1068438 Front Rigging Hanger Assembly,
Sector Style (22" Deep) - Left
1 13 B
1054571 Kit, Sector Block - Right 1 14 C
1054572 Kit, Sector Block - Left 1 14 C
1052957 Screw, Hex Head (1/4-20 x 2") 1 15
1026907 Washer (1/4 x 1/2 x 1/16") 1 16
1087076 Front Rigging Hanger Assembly, Genius Style with
Nylon Liner - Short (16"-21" Deep), Right
1 17 D
1087077 Front Rigging Hanger Assembly, Genius Style with
Nylon Liner - Short (16"-21" Deep), Left,
1 17 D
1087078 Front Rigging Hanger Assembly, Genius Style with
Nylon Liner - Long (22" Deep), Right
1 17 D
1087079 Front Rigging Hanger Assembly, Genius Style with
Nylon Liner - Long (22" Deep), Left
1 17 D
0181000 Liner, Nylon (3/4") 1 18
A - Includes front rigging hanger and item 2
B - Includes front rigging hanger and item 4
C - Includes sector block assembly and items 5 and 6
D - Includes front rigging hanger and item 8
NOTE:
Sector, Pin and Genius Style
NOTE: Front rigging hanger assemblies and seat pans share the same mounting hardware, see Seat Pan
Mounting Hardware page.
Form No.
99-150
94
To order call toll free 1-800-333-6900, or www.invacare.com
AT5544P Legrest Supports (Mechanical)
NOTE: Reference 2G Storm Series parts book (Form number 97-188) for pivot/slide tubes and footplates.
Form No.
99-150
95
To order call toll free 1-800-333-6900, or www.invacare.com
AT5544P Legrest Supports (Mechanical)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1087050 Legrest Support Assembly, Sector, Black - Right 1 11 A
1087051 Legrest Support Assembly, Sector, Black - Left 1 11 A
1094266 Support, Black Legrest, Right 1 12
1094267 Support, Black Legrest, Left 1 12
7930301 Package, Button Head Cap Screws (1/4-20 x 1-3/4") 25 13
1029501 Plug Button, Black (1") 1 14
1017148 Plug, Pivot 1 15
7930333 Locknut (1/4-20) 25 16
7930314 Screw, Slotted Hex Head (#10-32 x 1/2") 25 17
1025451 Screw, Slotted Hex Washer Head (#10-32 x 5/8") 1 28
1025454 Latch Housing - Right 1 19
1025455 Latch Housing - Left 1 19
1026158 Locknut (5/16-18) 1 110
1094268 Tube, Elevating Support (Black) Right 1 111
1094269 Tube, Elevating Support (Black) Left 1 111
1026030 Screw, Lug (5/16-24 x 1-3/8") 1 112
7930330 Locknut (5/16-24) 25 113
1082908 Spacer, Coved (5/16 x 29/32 x 7/16") 1 214
11919X000 Screw, Truss Head (3/8-16 x 1-1/2") 1 115
40363X000 Hex Nut (3/8"-16) 1 116
1058636 Washer, Nylon (25/64 x 7/8 x 1/32") 1 217
1025729 Screw, Self Tapping Pan Head (#8-32 x 3/8") 1 218
1017187 Cover, Top 1 119
1092666 Rod, Legrest Elevating, Right 1 120
1092667 Rod, Legrest Elevating, Left 1 120
1025133 Spacer, Legrest Pad 1 121
1032267 Spacer, Legrest Pad Mounting 1 122
1037110 Screw, Hex Head (5/16-24 x 3-1/2") 1 123
1028514 Screw, Hex Head (5/16-24 x 1-1/2") 1 124
1032266 Bracket, Legrest Pad Mounting, Black 1 125
8881091759 Pad w/Cover and Screws, Legrest Vinyl (Pair) 2 126 B,D
8881091764 Pad, Legrest Vinyl - Right/Left 1 126 C,D
01415X000-NLA Cover, Legrest Pad 1 126
1066591 Screws, Phillips Head (#10-32 x 11/16") 2 127
04526X019 Plate, Legrest Pad 1 128
A - Includes Items 2-20,21-25, and 28
B - Before 9/5/00
C - After 9/4/00
D - Specify U67 black upholstery when ordering
NOTE:
NOTE: Reference 2G Storm Series parts book (Form number 97-188) for pivot/slide tubes and footplates.
Form No.
99-150
96
To order call toll free 1-800-333-6900, or www.invacare.com
Genius Legrest (Mechanical)
Form No.
99-150
97
To order call toll free 1-800-333-6900, or www.invacare.com
Genius Legrest (Mechanical)
Genius Legrest Assembly
Description
Standard
Footplate
X-Large Footplate Standard Footplate X-Large Footplate
20" Long20" Long18" Long18" LongLegrest Tube
16"-24"16"-24"16"-24"16"-24"Width Range
1072597026400010725950196600Right Assembly
1072596026390010725940196500Left Assembly
1072905026380010729040138100Pair
Form No.
99-150
98
To order call toll free 1-800-333-6900, or www.invacare.com
Genius Legrest (Mechanical)
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1023966 Screw, Socket Head (#10-32 x 1-3/4") 1 11
0060000 Rubber Bumper 1 12
0140406 Screw, Socket Head Cap (5/16-18 x 1-1/2) 1 13
0061400 Decal, Warning Label Tie Down 1 14
0289824 Legrest Hanger Receptical w/ Dowel Pin 1 15
1096649 Guide Square w/ Brass Barb Insert 1 16
0176700 Bushing, Coved Latch Legrest Genius 1 17
0050100 Washer, Nylon Flat (1/4 x 1/2 x 1/16") 1 108
0051606 Screw, Socket Head Cap (1/4-20 x 1") 1 29
0052906 Screw, Socket Button Head (1/4-20 x 3/4") 1 310
0177802 Link, Rear 1 111
1086987 Plate, Push Pin 1 112
0179202 Link Plate 1 113
7930323 Package, Locknut (1/4-20) 25 114
7930333 Locknut (1/4-20) 25 115
0223506 Screw, Socket Head (1/4-20 x 1/2") 1 116
0180506 Screw, Support Bushing 1 117
0054700 Washer, Nylon (5/16 x 1/2 x 1/16") 1 218
0177702 Link, Front 1 119
0182406 Push Pin 1 120
1028486 Locknut, Low Profile (3/8-16) 1 121
0175600 Spacer, Coved (5/16 x 3/4 x 3/8") 1 222
0055206 Screw, Socket Head (5/16-18 x 1-3/4") 1 123
1072692 Lockwasher, Split (5/16") 1 124
1025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 125
0176422 Spacer, Coved 1 226
0055006 Locknut, Low Profile (5/16-18) 1 227
0176200 Bushing, Nylon Guide 1 228
0177100 Bushing, Legrest Support 1 129
0178224 Bar, Insert, Black 1 130
0175800 Bushing, Guide 1 131
0224600 Screw, Socket Head Cap (#10-32 x 3/4") 1 132
1105474 Screw, Hex Head (5/16-18 x 3-1/2) 1 133 A
1068159 Clamp, Calf Pad 1 134 A
1068160 Block, Legrest Pad Mount 1 135 A
1025716 Screw, Phillips Pan Head (#10-32 x 11/16") 1 236 A
04526X019 Plate, Legrest Pad 1 137 A
1068161 Block, Mounting 1 138 A
1109613 Hardware, Calf Pad 1 139 B
8881091811 Calf Pad (Left or Right) 1 140 A
0238124 Tube, Legrest 18" 1 141
0232424 Tube, Legrest 20" 1 141
0177022 Half Clamp 1 242
Form No.
99-150
99
To order call toll free 1-800-333-6900, or www.invacare.com
Loading...