MODEL: T173 |
LR3730 |
24 HR DIAL TIME SWITCH WITH “SKIPPER®”
DOUBLE POLE SINGLE THROW (DPST)
40 AMP. RESISTIVE, INDUCTIVE, TUNGSTEN OR
1000 VA. PILOT DUTY PER POLE - 120/208/277 VOLT AC; 2 HP (24 FLA) - 120V AC; 5 HP (28 FLA ) - 240V AC.
CLOCK MOTOR: 110-125 VOLTS - 60 HZ.
CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO ORDER REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.
|
ON/CUTOUT |
|
WIRING |
|
|
|
CLOCK |
|||
TIME |
DIAGRAM |
|
|
|
||||||
TRIPPER |
|
|
|
|
|
|
|
MOTOR |
||
POINTER |
DAY |
|
|
|
|
|
|
|
|
|
TIME |
ARROW |
|
|
|
A |
1 |
2 |
3 |
4 |
|
DIAL |
SKIPPER |
|
|
|
|
|||||
OFF |
|
|
|
NEUT. |
|
|
|
|
|
|
WHEEL |
|
|
|
LINE 1 |
|
|
|
|
|
|
TRIPPER |
|
|
|
|
|
|
|
TO |
||
|
|
|
|
|
|
|
|
|||
MANUAL |
|
|
|
|
LINE 2 |
|
|
|
|
|
SKIPPING |
|
|
|
|
|
|
GROUND |
LOAD(S) |
||
LEVER |
SCREW |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
120/240 VOLT 3 WIRE SUPPLY |
|
|
|
||
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
WIRING INSTRUCTIONS: To wire switch follow diagram above. Use solid or stranded COPPER only wire with insulation to suit installation. See gauge selection table for normal service applications. To make power connections remove 1/2 inch of insulation from wire ends. Insert bare ends of wire under the pressure plate of terminals. Use 3/16 or larger screwdriver to tighten terminal screws firmly. (25 lb-in minimum).
REPLACE INSULATOR BEFORE TURNING ON ELECTRICITY.
MINIMUM |
MAX. |
MIN. |
75°C INSULATION MAX. MOTOR |
PRESSURE PLATE |
||||
COPPER |
LOAD |
INSUL- |
|
LOAD (HP) |
|
|||
WIRE SIZE |
(AMP) |
ATION |
SINGLE PHASE |
3 PHASE |
|
|||
(AWG) |
|
TEMP(°C) |
TERMINAL SCREW |
|||||
|
|
|
120 V. |
240 V. |
208 V. |
240 V. |
||
14 |
15 |
60 |
1/2 |
2 |
|
|
MAKE SURE WIRE |
|
12 |
20 |
60 |
1 |
2 1/2 |
N/A |
N/A |
INSULATION CLEARS |
|
10 |
30 |
60 |
2 |
3 |
||||
|
|
PRESSURE PLATE |
||||||
8 |
40 |
75 |
- |
5 |
|
|
||
|
|
|
|
|
|
|
|
PROGRAMMING INSTRUCTIONS
1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge of CLOCK-DIAL, pointing to time (AM or PM) when ON and OFF operations are desired, tighten tripper screws firmly. For additional tripper pairs on CLOCK-DIAL order 156T1948A.
2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in either direction and align the exact time-of-day on the CLOCK-DIAL (the time now, when switch is being put into operation) to the pointer.
DO NOT MOVE POINTER.
3. TO SKIP OPERATION(S) ON SELECTED DAY(S): Insert SKIPPING SCREW(S) in SKIPPER WHEEL for day(s) automatic operation(s) is/are NOT required. Tighten screws firmly. Move MANUAL LEVER to
“OFF” and rotate SKIPPER WHEEL to locate correct day-of-week opposite DAY ARROW--”YESTERDAY” if ON/CUTOUT TRIPPER has not yet advanced wheel “TODAY” if it has.
OPERATING INSTRUCTIONS
• TO OPERATE SWITCH MANUALLY: Move MANUAL LEVER below
CLOCK-DIAL left or right as indicated by arrows. This will not effect next operation.
CAUTION: TO AVOID SLOW SWITCH ACTION FAILURE, DO NOT OPERATE SWITCH MANUALLY NOR PLACE A TRIPPER 4 HOURS PRIOR TO ON/CUTOUT TRIPPER SWITCHING.
• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to proper time- of-day. See programming instructions.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
158TS10958