Interlogix Concord Express Installation Manual

0 (0)

Concord Express Installation

Instructions

P/N 466-1665 • REV • OCT12

Copyright

Trademarks and

patents

Manufacturer

Contact information

Customer support

© 2012 UTC Fire & Security Americas Corporation, Inc.

Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved.

Concord is trademarks of UTC Fire & Security.

Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

UTC Fire & Security Americas Corporation, Inc.

1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA

www.utcfireandsecurity.com or www.interlogix.com

www.interlogix.com/customer-support

Notices

FCC Notices

FCC Part 15 Information to the User

Changes or modifications not expressly approved by UTC Fire & Security can void the user’s authority to operate the equipment.

FCC Part 15 Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.

Consult the dealer or an experienced radio/TV technician for help.

ACTA Part 68

This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among o ther information, the FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.

FCC Part 68 Registration No. B4ZUSA-27621-AL-E REN: 0.2B

The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may result in devices not ringing in response to an incoming call. In most areas, the sum of all device RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements as adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compliant modular jack that is also compliant. See the Installation Instructions for details.

Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ31X jack that is electrically in series and ahead of all other equipment attached to the same telephone line. Proper install ation is depicted in the following diagram. If you have any questions concerning these instructions, consult your local telephone company or a qualified installer about installing an RJ31X jack and alarm dialing equipment for you.

If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be given advance notice in order to maintain uninterrupted service.

If you experience trouble with this equipment, please contact the company that installed the equipment for service and/or repair information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning.

This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs

Patent Information

This product and the use of this product may be covered by one or more of the following patents: 5,805,063, 5,872,512, 5,942,981, 4,855,713. Except expressly provided herein, the purchase of this product shall not constitute a license or otherwise provide a right to practice a method covered by any of the identified patents. UTC Fire & Security hereby grants the purchaser of this product a limited, non-exclusive license to practice the methods patented in the identified patents solely with products manufactured, sold or licensed by UTC Fire & Security. This license grant does not extend to the use of unlicensed, third party products with this product.

Canada notice

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together

Caution: Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. Load Number: .1 The term “IC:” before the certification/registration number only signifies that the Industry Canada

technical specifications were met. IC: 867A 787SIMON

´

“AVIS: - L étiquette du ministère des Communications du Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d ´ exploitat ion et de sécurité des réseaux de télécommunications. Le ministère n ´ assure toutefois pas que le matériel fonctionnera a la satisfaction de l ´ utilisateur.

Avant d ´ installer ce matériel, l ´ utilisateur doit s ´ assurer qu´ il est permis de le raccorder aux installations de l ´ enterprise locale de télécommunication. Le matériel doit également etre installé en suivant une méthod acceptée de raccordement. Dans certains cas, les fils intérieurs de l´ enterprise utilisés pour un service individuel a ligne unique peuvent etre prolongés au moyen d´ un dispositif homologué de raccordement (cordon prolongateur téléphonique interne). L ´ abonné ne doit pas oublier qu ´ il est possible que la conformité aux conditions énoncées ci -dessus n ´ empechent pas le dégradation du service dans certaines situations. Actuellement, les enterprises de télécommunication ne permettent pas que l ´ on raccorde leur matériel a des jacks d ´ abonné, sauf dans les cas précis prévus pas les tarrifs particuliers de ces enterprises.

Les réparations de matériel homologué doivent etre effectuées pas un centre d ´ entretien canadien autorisé désigné par le fournisseur. La compagne de télécommunications peut demander a l ´ utilisateur de débrancher un appareil a la suite de réparations ou de modifications effectuées par l ´ utilisateur ou a cause de mauvais fonctionnement.

Pour sa propre protection, l ´ utilisateur doit s ´ assurer que tous les fils de mise a la terre de la source d ´ énergie électrique, des lignes téléphoniques et des canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection des installations électriques, ou a electricien, selon le cas”.

Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel termin al, doit etre incluse dans l ´ information qui accompagne le materiel homologué. La note pourrait etre rédigée selon le modèle suivant:

“L ´ indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etre raccordée a un circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut etre constituée de n ´ import somme des indices de charge de l ´ ensemble des dispositifs ne dépasse pas

100.”

L ´ Indice de charge de cet produit est ____________.

Content

Notices

 

 

 

 

Chapter 1 Installation

1

 

 

 

Special installation requirements

2

 

Planning the Installation

6

 

 

Installing

the System 7

 

 

 

Chapter 2 Programming 27

 

 

 

Entering programming mode 28

 

 

Programming Tier 1 Menu Items

30

 

Programming Tier 2 Menu Items

32

 

Chapter 3 Testing/Troubleshooting

71

 

 

Troubleshooting 76

 

 

 

Appendix A System configuration worksheets 85

 

Appendix B Programming mode menus and settings

103

Appendix C Software release notes and specifications

107

Concord Express Installation Instructions

i

Chapter 1

Installation

This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compatible devices.

Planning sheets are included for you to record hardware layout and software programming settings.

Content

 

 

 

 

 

 

 

 

 

Special installation requirements

 

2

 

 

 

UL Listed Systems

2

 

 

 

 

 

UL-Canada Listed Systems

5

 

 

 

 

Planning the Installation

6

 

 

 

 

 

Standard Panel

6

 

 

 

 

 

 

Touchpads

6

 

 

 

 

 

 

 

SnapCard™

7

 

 

 

 

 

 

 

Installing the System

7

 

 

 

 

 

 

Determine the Panel Location

8

 

 

 

Total System Power and Wire Length Guidelines

8

 

Mounting the Panel

10

 

 

 

 

 

Identify Panel Components

11

 

 

 

Connecting the Panel to Earth Ground

12

 

 

Installing

Optional SnapCards

13

 

 

 

Installing

Optional Hardwire Input Modules (HIMs)

13

 

Connecting Detection Devices to Panel Zone Inputs#14

 

Connecting Sirens#17

 

 

 

 

 

Connecting Siren Drivers, Self-Contained Sirens, and Bells

19

Connecting Touchpads#20

 

 

 

 

 

Installing

an RJ-31X Phone Jack (13-081)#21

 

 

Connecting the Phone Line to the Panel with a DB-8 Cord

22

Connecting the AC Power Transformer

23

 

 

Powering Up the Panel 24

 

 

 

 

 

Concord Express Installation Instructions

 

 

 

 

1

Chapter 1

Special installation requirements

This security system can be used as a wire warning system, an intrusion alarm system, an emergency notification system, or any combination of the three.

Some installations may require configurations dictated by city or state codes, insurance, or Underwriter’s Laboratories (UL). This section describes the various component and configuration listings.

UL Listed Systems

This section describes the requirements for UL Listed systems.

Basic System

Control Panel (60-806, 60-806-95R)

Backup Battery, 12 VDC, 4 AH (60-681)

SuperBus 2000 2x16 LCD Touchpad (60-746-01), SuperBus 2000 Fixed Display Touchpad (60-820), SuperBus 2000 2x20 LCD Touchpad (60-803), or SuperBus 2000 2x20 VFD Touchpad (60-804)

Standard Class II 16.5 VAC, 25 VA Power Transformer; manufacturer—Tech Electro Ind, Inc. Part No. 48A0164 (60-822) or Standard Class II 16.5 VAC, 40 VA Power Transformer; MG Electronics Model # MGT1640CC, UTC Fire & Security # 22-156

15-Watt, Dual Tone Siren (13-469) or Hardwire Siren (13-046)

Household Burglary Alarm System Unit (UL 1023)

Basic system, plus:

Hardwire Magnetic Contact (Sentrol part # 1075-N or 1038T-N) or Wireless Learn Mode Door/Window Sensor (60-362), Wireless Learn Mode PIR Motion Sensor (60-703-95, 60-511, or 60-639)

IMMEDIATE TROUBLE BEEPS set to on

UL 98 OPTIONS set to on

RECEIVER FAILURE set to on

EXIT DELAY set to 60 seconds or less

QUICK EXIT set to off

SIREN TIMEOUT set to 4 minutes or more

SIREN VERIFY set to on

ENTRY DELAY set to 45 seconds or less

2

Concord Express Installation Instructions

Chapter 1

RF TX TIMEOUT set to 24 hours

EXTENDED DELAY set to off

TWO TRIP ERROR set to off

ALARM VERIFY set to off

DISABLE TROUBLE BEEPS set to off

SYSTEM TAMPER set to on

Household Fire Warning System (UL 985)

Basic system plus:

Hardwire Smoke Detector:

System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, or 2400TH learned into Sensor Group 26 Sentrol (ESL) models 429AT, 521B, or 521BXT learned into sensor group 26

Wireless Smoke Sensor 60-506-319.5 or 60-645-95 learned into sensor group 26

IMMEDIATE TROUBLE BEEPS set to on

UL 98 OPTIONS set to on

RECEIVER FAILURE set to on

SIREN VERIFY set to on

RF TX TIMEOUT set to 4 hours

ALARM VERIFY set to off

DISABLE TROUBLE BEEPS set to off

UL 1023 & 985 24-Hour Backup

For 24-hour backup, the total current draw for all connected devices is limited to 90 mA continuous using a 4.0 AH battery.

SIA System Requirements

Note: UL requirements take priority over SIA requirements.

SIA system requirements are the same as those described for a UL Listed Basic System on page 1, plus:

If multiple annunciation is required, use Hardwire Siren part no.13-046.

SIA Setting Requirements

The following table describes programming requirements to meet ANSI-SIA CP01.

Concord Express Installation Instructions

3

Chapter 1

Shortcut

Function

Programmin

Default

Required setting

#

 

g page

setting

 

 

 

reference

 

 

 

 

 

 

 

0003

SIA False

34

On

On

 

Alarm

 

 

 

 

Reduction

 

 

 

 

 

 

 

 

0013

Exit

35

On

On

 

Extension

 

 

 

 

 

 

 

 

0014

Auto Stay

35

On

On

 

Arming

 

 

 

 

 

 

 

 

0016

Duress

36

Disabled

Disabled

 

Code

 

 

 

 

 

 

 

 

02005

Dialer Abort

43

On

On

 

 

 

 

 

02006

Dialer Abort

43

30 Sec.

15-45 sec.

 

Delay

 

 

 

 

 

 

 

 

02007

Cancel

43

On

On

 

Message

 

 

 

 

 

 

 

 

02009

Call Wait

44

Disabled

On if reporting to central station and customer

 

Cancel

 

 

has call waiting

 

 

 

 

 

0310

Entry Delay

46

30 sec.

30-240 sec.

 

 

 

 

 

0311

Exit Delay

47

60 sec.

45-184 sec.

 

 

 

 

 

05014

Swinger

52

1

1

 

Limit

 

 

 

 

 

 

 

 

0900

Smoke

61

Off

On if smoke alarms are programmed into

 

Verify

 

 

system

 

 

 

 

 

N/A

Cross

88

Disabled

Enabled for zones with a high probability of

 

Zoning

 

 

false alarms

 

 

 

 

 

The following table describes non-programmable (hard coded) system operation as required to meet ANSI-SIA CP-01 and is provided only for your reference.

Function

Operation

 

 

Disarm During Entry Delay

Enter Code Only (or 1 + CODE)

 

 

Cancel Alarm

Enter Code Only (or 1 + CODE)

 

 

Abort Annunciation

Enabled

 

 

Cancel Report Annunciation

Enabled

 

 

UL 1635 Digital Alarm Communicator System

Note: For UL 1635 installations, Entry Delay plus Dialer Abort Delay must not exceed 60 seconds.

Same as UL 1023 & 985 plus:

4

Concord Express Installation Instructions

Chapter 1

AC FAILURE set to on

PHONE NUMBER must be programmed

HIGH LEVEL REPORTS set to on.

LOW LEVEL REPORTS set to on

PHONE TEST set to on

AUTO PHONE TEST set to on

PHONE TEST FREQ. set to 1

NEXT PHONE TEST set to 1

LOW CPU BATTERY set to on

COMM FAILURE set to on

RF TX TIMEOUT set to 4 hours

Central Station Reporting

The panel has been tested with the following central station receivers using SIA and Contact ID reporting formats:

CS-5000 Central Station Receiver

Sur-Gard Central Station Receiver with models SG-DRL2A and SG-CPM2

UL-Canada Listed Systems

This section describes the requirements for ULC (UL Canada) Listed systems.

CSA Certified Accessories

The UL-Canada Basic System is nearly the same as the “UL Basic System” described previously, the only difference being that you must use the ITI 60- 679-CN Class II transformer (Basler part number BE 116250-AAA) to power the panel.

Residential Burglary Alarm System Unit (CAN/ULC-S309)

Same as “UL Basic System and Household Burglary Alarm System Unit (UL 1023)” described previously and siren timeout must be set to 5 minutes or more.

Residential Fire Warning System Control Unit (CAN/ULC-S545-M89)

Same as “UL Basic System and Household Fire Warning System (UL 985)” described previously.

Note: For 24-hour backup, external power drain is limited to 90 mA continuous using a 4.0AH battery.

California State Fire Marshall Listed Systems

Same as Household Fire Warning System (UL 985), plus:

Concord Express Installation Instructions

5

Chapter 1

SMOKE VERIFY must be set to off

Planning the Installation

This section describes the system capabilities to help you get familiar with the system. To help you prepare for system installation, Appendix A provides planning sheets with tables that let you record the hardware and programming configuration of the system.

Standard Panel

The following describes the basic panel (out-of-box) hardware capabilities.

Power: Input for an AC step-down, plug-in style transformer.

Auxiliary Power Output: Output that supplies up to 750 mA (90 mA for UL Listed systems) at 12 VDC for bus devices and hardwired detectors, such as touchpads and motion detectors.

Bus A and B: Input and output that provide communication between bus devices and the panel.

2 Onboard Outputs: One 12-volt and one open-collector output that can be set up to activate other signalling devices, based on system events.

6 Supervised Hardwire Zones: Factory programmed inputs for various hardwired detectors (see “Accessory Modules Menu” on page 60 for a list of factory programmed settings). Zone 6 can be set up in programming to accept 2-wire smoke detectors.

Built-In Radio Receiver: Allows use of UTC Fire & Security 319.5 MHz.

crystal and/or SAW Learn Mode wireless sensors and touchpads.

Phone Line Connection: Allows the panel to communicate with central monitoring stations and pagers.

Touchpads

The following describes the different touchpads that can be used for system programming and operation.

SuperBus 2000 2x16 LCD Alphanumeric Touchpad: Provides complete system programming and operation control. Displays system messages, and indicates system status.

6

Concord Express Installation Instructions

Chapter 1

SuperBus 2000 2x20 LCD/VFD Alphanumeric Touchpads: Provide complete system programming and operation control, display system messages and indicate system status.

SuperBus 2000 Fixed Display LCD Touchpad: Provides operation control and user programming access (not installer or dealer programming). Displays system messages and indicates system status.

SnapCard™

The following SnapCards expand the system as described:

8Z Input SnapCard: Provides eight additional hardwire zone inputs, of which two are dedicated for 2-wire smoke detectors.

4 Output SnapCard: Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events.

4Z Input/2 Output Combo SnapCard: Provides three standard hardwire zone inputs, one 2-wire smoke detector loop input, and two outputs that can be set up to activate other signalling devices that are based on system events.

Installing the System

This section describes how to install the system control panel. Before starting the installation, plan your system layout and programming using the worksheets provided in Appendix A.

Installing the system consists of the following steps:

Determining the Panel Location

Identifying Total System Power and Wire Length Guidelines

Mounting the Panel

Identifying Panel Main Components

Installing Optional SnapCards

Installing Optional HIMs

Connecting Detection Devices to Panel Zone Inputs

Connecting Sirens

Connecting Touchpads

Installing an RJ-31X Phone Jack

Connecting the Phone Line to the Panel with a DB-8 Cord

Connecting the AC Power Transformer

Powering Up the Panel

Concord Express Installation Instructions

7

Chapter 1

Determine the Panel Location

Before permanently mounting the panel, determine the location using the following guidelines:

To help reduce wire run lengths and labor, centrally locate the panel with relation to detection devices whenever possible.

Avoid running wires parallel with electrical wiring or fixtures, such as

fluorescent lighting, to prevent wire runs from picking up electrical noise.

Mount the panel at a comfortable working height (about 45 to 55 inches from

the floor to the bottom of the panel, as shown in Figure 1 below).

Leave space to the left and right of the panel for wiring, phone jack, and optional modules.

For installations that include wireless sensors, allow at least 10 inches above the panel cabinet for the antenna.

Allow at least 24 inches in front of the panel for opening the panel door.

Figure 1: Determining panel location

Total System Power and Wire Length Guidelines

Note: A) Class 2, Class 3, and power-limited fire alarm circuits must be installed using FPL, FPLR, FPLP, or substitute cable permitted by the National Electrical Code ANSI/NFPA 70. Wire that extends beyond the cable jacket must be separated from all other conductors by a minimum of 1/4-inch or by a nonconductive barrier.

OR

8

Concord Express Installation Instructions

Chapter 1

(B) Class 2, Class 3, and power-limited fire alarm circuit conductors must be installed as Class 1 or higher circuits.

Table 1 below describes panel voltage/current output ranges. See Appendix A for maximum and standby device current draw.

Table 1: Panel voltage/surrent output ranges

Panel terminal

Voltage range

Max. current

 

 

 

 

 

4

(+12V)

8.5 - 14.2

VDC

750 mA—non-UL Listed systems

 

 

9.1 - 14.2

VDC (UL)

90 mA—UL Listed systems

 

 

 

 

 

7

(OUT1/+12)

8.5 - 14.2

VDC

1.25 A at default configuration—non-UL Listed systems

 

 

 

 

650 mA—UL Listed systems

 

 

 

 

17 (Z6/2W+)

8.9 - 13.7

VDC

80 mA

 

 

 

 

 

Total system wire allowed varies depending on devices powered by the panel, wire length between devices and the panel, and the combined wire length of all devices.

Table 2 below describes the maximum wire length allowed between compatible devices and the panel.

Table 2: Maximum device wire lengths

Device

Max. wire length to panel

Wire type

 

 

 

 

AC Power Transformer

18

AWG—25 ft.

Stranded

 

 

 

 

Earth Ground

16

AWG—25 ft.

Solid

 

 

 

Telephone (RJ-31X)

as required

Stranded

 

 

 

Detection Devices

22 or 18 AWG—300 ohms maximum loop resistance +

Stranded

 

2k end-of-line

 

 

 

 

 

2-Wire Smoke Detectors

22

AWG—330 ft.

Stranded

 

18

AWG—830 ft.

 

 

(based on 10 ohms maximum loop resistance + 2k

 

 

end-of-line)

 

 

 

 

 

Sirens

22

AWG—80 ft.

Stranded

 

18

AWG—200 ft. when using siren models 13-469 or

 

 

13-046

 

 

 

 

 

SuperBus 2000 2x16

22

AWG—300 ft.

Stranded

LCD Alphanumeric

18

AWG— 750 ft.

 

Touchpad

 

 

 

 

 

 

 

SuperBus 2000 Fixed

22

AWG—300 ft.

Stranded

Display LCD Touchpad

18

AWG— 750 ft.

 

 

 

 

 

SuperBus 2000 2x20

22

AWG—250 ft.

Stranded

LCD Alphanumeric

18

AWG— 600 ft.

 

Touchpad

 

 

 

 

 

 

 

Concord Express Installation Instructions

9

Chapter 1

Device

Max. wire length to panel

Wire type

 

 

 

 

SuperBus 2000 2x20

22

AWG—250 ft.

Stranded

VFD Alphanumeric

18

AWG— 600 ft.

 

Touchpad

 

 

 

 

 

 

 

SuperBus 2000 Hardwire

22

AWG—1,800 ft.

Stranded

Input Module

18

AWG— 4,500 ft.

 

 

 

 

 

Mounting the Panel

Use the following procedure to mount the panel to the wall or wall studs.

Caution: Make sure you are free of static electricity whenever you work on the panel with the cover open. To discharge any static, first touch the metal panel chassis, then stay in contact with the chassis when touching the circuit board. Using an approved grounding strap is recommended.

To mount the panel cabinet and circuit board:

1.Open the panel door and slide it up to remove it from the cabinet. Set the door aside.

2.Remove the knockout to provide access for system wiring (see Figure 2 below).

3.Feed all device wires through the knockout and place the panel in position against the wall.

4.Level the panel and mark the top and bottom mounting holes (see Figure 2 below).

Figure 2: Mounting holes

10

Concord Express Installation Instructions

Chapter 1

5.Install anchors where studs are not present.

6.Partially insert screws into the two top mounting hole locations, then hang the panel on the two screws.

7.Recheck for levelness, insert the two lower screws, and tighten all four mounting screws.

8.Install the antenna housing (included with the panel) by pushing it down into the top left hole of the cabinet until it snaps into place (see Figure 3 below).

9.Install the circuit board into the cabinet, inserting the loop antenna loop up into the antenna housing (see Figure 3 below), then secure the circuit board with the four mounting screws (included).

Figure 3: Installing the antenna housing and the circuit board

Identify Panel Components

Before installing devices and making wiring connections, familiarize yourself with the main components of the panel. Figure 4 on page 12 shows the main component locations on the circuit board.

Concord Express Installation Instructions

11

Chapter 1

Figure 4: Main component locations

Connecting the Panel to Earth Ground

For maximum protection from lightning strikes and transients, connect the lowerright circuit board screw to earth ground as shown in Figure 5 below. Use 16gauge, solid copper wire from an earth grounded cold water pipe clamp to the panel.

Note: For best results, it is recommended that you crimp a spade lug on the wire end at the panel and secure the lug under the circuit board screw as shown in Figure 5 below.

Figure 5: Connecting the panel to earth ground

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Concord Express Installation Instructions

Chapter 1

Installing Optional SnapCards

The SnapCard Header on the lower-left side of the panel accepts one of the following SnapCard models:

8Z Input SnapCard—60-757

4 Output SnapCard—60-758

4Z Input/2 Output Combo SnapCard—60-756

Install the desired SnapCard onto the panel SnapCard Header and secure it in place with two screws, included with the card (Figure 6 below).

Connect all necessary input/output wiring using the installation instructions included with the SnapCard.

Figure 6: Installing a SnapCard

Installing Optional Hardwire Input Modules (HIMs)

Each SuperBus 2000 8-Zone Input Module (60-774) adds eight supervised hardwire zones to the system. Both normally open and normally closed detectors can be wired to module inputs (see Figure 8 on page 15).

Connect all necessary input/output wiring using the installation instructions included with the HIM.

Note: Use of the HIM with the Concord™ Express panel has not been investigated by UL.

Concord Express Installation Instructions

13

Chapter 1

Figure 7: Installing and connecting the HIM in the Concord Express

Connecting Detection Devices to Panel Zone Inputs

The panel comes with six factory programmed onboard hardwire zones (see “Accessory Modules Menu” on page 60 for factory settings). Zone inputs 1 through 6 are supervised using a 2k-ohm, end-of-line resistor (included with panel) at the last device on the circuit.

Note: Install an end-of-line resistor on all unused, factory programmed, onboard panel zones.

All six zones accept either normally open (N/O) or normally closed (N/C) detection devices (see Figure 8 on page 15).

The maximum loop resistance for each zone input is 300 ohms, plus the 2k end- of-line (EOL) resistor.

Connecting Intrusion Detection Devices

Figure 8 on page 15 shows the typical wiring for N/C and N/O door/window intrusion detection.

14

Concord Express Installation Instructions

Chapter 1

Figure 8: Connecting N/C and N/O intrusion detection circuits

Figure 9 below shows the typical wiring for Optex model RX-040 (PI) PIR motion detectors. The minimum available panel voltage for hardwired PIR motion detectors is 8.5 VDC (9.1 VDC for UL Listed systems).

Figure 9: Connecting a PIR motion detector

Connecting 2-Wire Smoke Detectors

Zone input 6 can be set up (in program mode) to accept 12 VDC, 2-wire smoke detectors by the following manufacturers:

System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, 2400TH

Sentrol (ESL) models 429AT, 521B, 521BXT—models 521B and 521BXT require the

following dip switch settings: 1-on, 2-off.

Concord Express Installation Instructions

15

Chapter 1

Note: When using 2-wire smoke detectors on Zone 6, the Two-Wire Smoke setting (in program mode) must be turned on before entering the LEARN SENSORS menu. See ONBOARD OPTIONS—INPUTS in the section “Entering programming mode” on page 28 for complete details.

WARNING: Use only 2-wire smoke detector models described above. Alarm signals from other detectors may not be processed correctly if the panel has lost AC power and is operating only from the backup battery.

When set up for 2-wire smoke detectors, zone 6 can handle up to 10 smoke detectors with 120 µA maximum idle current per detector. Maximum total loop current allowed in an alarm condition is 80 mA. The maximum loop resistance for 2-wire smoke detectors connected to zone input 6 is 10 ohms, plus the 2k end- of-line resistor.

Caution: Panel terminal 16 (ZCOM/2W-) cannot be used as a common loopconnection for any other zones, when using Zone 6 for 2-wire smoke detectors.

Connect one or more 2-wire smoke detectors to the panel as shown in Figure 10 below.

Figure 10: Connecting 2-wire smoke detectors

Connecting 4-Wire Smoke Detectors

Zone inputs 1 through 6 can be used with 4-wire smoke detectors that latch and remain in the alarm state until power is removed and then restored to the detector.

16

Concord Express Installation Instructions

Chapter 1

The panel provides this power interruption from panel terminal 8 (OUT2/OC) provided that the output configuration number is set (in program mode) to 01500.

For more information on output configuration numbers, see the section “Programming the Panel” and the tables in Appendix A. Use only 4-wire smoke detectors that operate on 8.5 to 14.2 VDC.

Note: The Two-Wire Smoke setting (in program mode) must be off when connecting

4-wire smoke detectors to zone 6. For UL Listed systems, 4-wire smoke detectors cannot be connected to onboard panel zone inputs.

Connect up to five Sentrol (ESL) model 449AT (ITI part no. 13-360) smoke detectors to panel power input as shown in Figure 11 below.

Figure 11: Connecting 4-wire smoke detectors

Connecting Sirens

Note: Install all sirens/speakers indoors, in a concealed location.

Two onboard programmable outputs allow for siren connections when using the default setting of each output. For more information on output configuration numbers, see the section “Programming the Panel” and the tables in Appendix A.

The following describes siren connections using the default settings of each onboard output.

Concord Express Installation Instructions

17

Chapter 1

Note: If the backup battery is not connected, or if the configuration of panel terminal 7 is programmed to anything other than the default (00410), then the combined currents of terminal 7 (OUT 1/+12) and terminal 4 (+12V) must not exceed 750 mA.

15-Watt, Dual Tone Siren (13-469)

Panel terminal 7 (OUT1/+12V) is a +12V programmable output. At the default configuration setting (00410), this output can provide up to 1.25 A during an alarm (650 mA for UL Listed systems) if the backup battery is connected.

The default configuration setting (00410) activates the output during any audible alarm, allowing for a siren connection without changing the output configuration number.

Note: For UL Listed systems, Siren Verify must be on.

Figure 12: Connecting 15-watt, Dual-Tone siren 13-469

Note: Some versions of this siren may have two wires of each color. Only one black wire and one yellow wire are needed for panel connections.

For UL Listed installations, you can connect only one 15-Watt, Dual-Tone Siren to panel terminals 3 and 7 as shown in Figure 12 above. For all other installations, connect up to two sirens. This siren does not require an end-of-line resistor.

Hardwire Siren (13-046)

Connect one or two sirens to the panel with supervision as shown in Figure 13 on page 19. If Siren Verify is turned off, the 2k end-of-line resistor is not required.

Note: For UL Listed systems, Siren Verify must be on and the 2k end-of-line resistor installed.

18

Concord Express Installation Instructions

Interlogix Concord Express Installation Manual

Chapter 1

Figure 13: Connecting hardwire siren 13-046

Interior Piezo Siren (30-006)

Panel terminal 8 (OUT2/OC) is an open-collector (switched path-to-ground), programmable output that can handle up to a 200 mA current.

The default setting (01710) activates the output for status and alarm tones, which allows for a piezo siren connection without changing the output configuration number.

Connect the piezo siren to the panel terminals with a 2k end-of-line resistor as shown in Figure 14 below.

Note: Piezo siren connections to terminal 8 require a 2k end-of-line resistor that can be located at the panel since it does not supervise the circuit.

Figure 14: Connecting an interior piezo siren

Note: If using an external power supply instead of panel terminal 4, the supply voltage must be limited to 9.5 VDC maximum and the negative side of the power supply must be connected to panel ground (terminal 3).

Connecting Siren Drivers, Self-Contained Sirens, and

Bells

Power for a siren driver, self-contained siren, or bell can be connected to panel terminals 7 (OUT1/+12V) and 3 (GND).

Concord Express Installation Instructions

19

Chapter 1

Panel terminal 7 (OUT1/+12V) is a +12-volt programmable output. At the default configuration setting (00410), this output can provide up to 1.25 A during an alarm (650 mA for

UL Listed systems) if the backup battery is connected.

Note: If the backup battery is not connected, or if the configuration of panel terminal 7 is programmed to anything other than the default (00410), then the combined currents of terminal 7 (OUT 1/+12) and terminal 4 (+12V) must not exceed 750 mA.

The default configuration setting (00410) activates the output during any audible alarm.

The following siren drivers, self-contained sirens, and bells have been tested and found compatible for use with the panel:

Moose Models MPI-11 (use only 8-ohm speaker loads), MP-47, MP-47B

Altronix Model ALSD2 (4- or 8-ohm speaker loads)

ATW Models DT-24, DS508 (both self-contained)

Wheelock MB-G6-12 Six-inch, 12V Bell

Refer to the manufacturer’s documentation for installation details.

Connecting Touchpads

• SuperBus 2000 2x16 LCD Alphanumeric Touchpad (60-746-01)

• SuperBus 2000 2x20 LCD Alphanumeric Touchpads (60-803, 60-809)

• SuperBus 2000 2x20 VFD Alphanumeric Touchpad (60-804, 60-810)

SuperBus 2000 Fixed Display LCD Touchpad (60-820)

Alphanumeric touchpads can be used for installer programming, system operation, and user programming. Fixed display touchpads can be used for system operation and user programming but not for installer programming.

Note: Be sure to have an alphanumeric (programming) touchpad on hand for onsite programming in installations that do not include one as part of the final system configuration. This programming touchpad can be connected to the Programming Touchpad Header (see Figure 15 on page 21) using a Programming Touchpad Cable (part no. 60-791).

Connect 2x16 and fixed display LCD touchpads to the panel power output and bus terminals as shown in Figure 15 on page 21.

The 2x20 LCD/VFD touchpads include a supervised hardwire input for connection to a hardwire detection device (see Figure 15 on page 21 for an example of a normally closed connection).

20

Concord Express Installation Instructions

Chapter 1

Connect 2x20 LCD/VFD touchpads to the panel power output and bus terminals as shown in Figure 15 below.

Figure 15: Connecting 2x16 Alphanumeric Fixed Display LCD touchpad and 2x20 LCD/VFW touchpads

Installing an RJ-31X Phone Jack (13-081)

Note: The panel cannot be used on a digital or PBX phone line. These systems are designed only for digital type devices that operate anywhere from 5 volts DC and up. The panel uses an analog modem and does not have a digital converter, adapter, or interface to operate with such systems.

Use the following guidelines when installing an RJ-31X phone jack for system control by phone and central station monitoring.

Locate the RJ-31X jack (CA-38A in Canada) no further than five feet from the panel.

• The panel must be connected to a standard analog (loop-start) phone line.

For full line seizure, install an RJ-31X phone jack on the premises phone line so the panel is ahead of all phones and other devices on the line. This allows the panel to take control of the phone line when an alarm occurs even if the phone is in use or off-hook.

If an analog line is not available, contact your customers’ telecommunications specialist and tell him/her you need an analog line off the phone switch (PBX mainframe) or a 1FB (standard business line).

Concord Express Installation Instructions

21

Chapter 1

To connect a phone line to the panel using an RJ-31X/CA-38A jack:

1.Run a 4-conductor cable from the TELCO protector block to the jack location (see A in Figure 16 below).

2.Connect one end of the cable to the jack (see B in Figure 16 below).

Figure 16: Installing an RJ-31X Phone Jack

3.At the TELCO protector block, remove the premises phone lines (lines from phone jacks on premises) from the block and splice them to the black and white (or yellow) wires of the

4-conductor cable (see C in Figure 16 above).

Note: Connecting the panel to an analog line off the phone switch places the panel ahead of the phone system which prevents panel access from phones on the premises. However, the panel can still be accessed from off-site phones.

4.Connect the green and red wires from the 4-conductor cable to the TIP (+) and RING (-) posts on the block (see D in Figure 16 above).

5.Check the phones on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and make corrections where necessary. Proceed to the “Troubleshooting” section of this manual if problems persist.

Connecting the Phone Line to the Panel with a DB-8 Cord

After installing the RJ-31X jack, you are ready to connect the phone line to the panel. A DB-8 cord (not included) uses a plug at one end for connecting to the RJ-31X module and flying leads on the other end for panel terminal connections.

22

Concord Express Installation Instructions

Chapter 1

To connect the DB-8 cord to the panel terminals and RJ-31X jack:

1.Connect the green, brown, gray, and red flying leads from the DB-8 cord to panel terminals 18, 19, 20, and 21 (see Figure 17 below).

2.Insert the DB-8 cord plug into the RJ-31X (see Figure 17 below).

Figure 17: Connecting the DB8 cord

3.Check the phones on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to the “Troubleshooting” on page 76 of this manual if problems persist.

Connecting the AC Power Transformer

Note: If you plan on connecting an alphanumeric touchpad to the programming touchpad header on the panel, do not connect it until after the panel is powered up. Refer to “Entering Programming Mode.”

The panel must be powered by a plug-in stepdown transformer that supplies 16.5 VAC, 25 VA (60-822 or 60-679-CN). Connect the power transformer to the panel as shown in Figure 18 on page 24.

Caution: Do not plug in the power transformer at this time. The panel must be powered up using the sequence of steps described in “Powering Up the Panel” on page 24.

Concord Express Installation Instructions

23

Chapter 1

Figure 18: Connecting the power transformer

Powering Up the Panel

Note: Without AC power, shutdown will occur if battery voltage falls below 10.2 VDC.

After installing SnapCards and wiring all devices to the panel, you are ready to apply AC and backup battery power to the panel.

To power up the panel:

1.Connect the red and black battery leads (included with panel) to the lugs located in the upper-left area of the panel circuit board (see Figure 19 below).

Figure 19: Connecting the backup battery

2.Connect the battery leads to the battery terminals as shown.

3.Plug the transformer into an outlet that is not controlled by a switch or ground fault circuit interrupt (GFCI).

24

Concord Express Installation Instructions

Loading...
+ 87 hidden pages