Intel DDR400, DDR333, FSB400, FSB800, FSB533 User Manual

...
4 (1)
TRADEMARK
All products and company names are trademarks or registered
trademarks of their respective holders.
These specifications are subject to change without notice.
Manual Revision 1.0
March 27, 2003
User’User’
User’User’
User’
s
ManualManual
ManualManual
Manual
An Intel Socket 478 Processor BasedAn Intel Socket 478 Processor Based
An Intel Socket 478 Processor BasedAn Intel Socket 478 Processor Based
An Intel Socket 478 Processor Based
MainboardMainboard
MainboardMainboard
Mainboard
SupporSuppor
SupporSuppor
Suppor
ts ts
ts ts
ts
FSB400 / DDR266 (PC2100)FSB400 / DDR266 (PC2100)
FSB400 / DDR266 (PC2100)FSB400 / DDR266 (PC2100)
FSB400 / DDR266 (PC2100)
FSB533 / DDR266/333 (PC2100/PC2700)FSB533 / DDR266/333 (PC2100/PC2700)
FSB533 / DDR266/333 (PC2100/PC2700)FSB533 / DDR266/333 (PC2100/PC2700)
FSB533 / DDR266/333 (PC2100/PC2700)
FSB800 / DDR333 (PC2700)FSB800 / DDR333 (PC2700)
FSB800 / DDR333 (PC2700)FSB800 / DDR333 (PC2700)
FSB800 / DDR333 (PC2700)
FSB800 / DDR400 (PC3200)FSB800 / DDR400 (PC3200)
FSB800 / DDR400 (PC3200)FSB800 / DDR400 (PC3200)
FSB800 / DDR400 (PC3200)
$ 2,)
DISCLAIMER OF WARRANTIES:
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE OF THE MANUFACTURER LIMITED
WARRANTY. THE MANUFACTURER EXPRESSLY EXCLUDES ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING ITS
PRODUCTS; INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR
NONINFRINGEMENT. THIS DISCLAIMER OF WARRANTIES SHALL
APPLY TO THE EXTENT ALLOWED UNDER LOCAL LAWS IN THE
COUNTRY PURCHASED IN WHICH LOCAL LAWS DO NOT ALLOW
OR LIMIT THE EXCLUSION OF THE IMPLIED WARRANTIES.
80 Port Frequently Asked Questions
Below is a list of some basic POST Codes, possible problems, and solutions. For
more detailed information about POST Codes, refer to Appendix D in this manual.
POST C O DE Pro bl em Sol ut io n
FFh or CFh 1.BIOS chip inserte d
incorrectly
2. Incorrec t BIOS update
version
3. Mainboard pro ble m
4. Add-o n card inse rted
incorrectly.
1. Reinsert the BIOS
chip
2. Download the correct
BIOS version update
from the manufacturer's
Web site.
3. Replace mainboard
4. Remove and replace the
add-on card
C1h - C5h 1. Memory module
inserted incorrectly
2. M emo ry compatibility
problem
3. Memo ry m o dule
damaged
1. Reinsert memory
module
2. Replace memory
with correct type
3. Replace memory
module
2Dh 1. Error occured in VGA
BIOS
2. VGA card inserted
incorrectly
1. Replace VGA card
2. Reinsert the VGA
card
26h Overclock error Clear CMOS or press the insert
key to power on the system
07 h - 12h 1. Init ke ybo ard
controller error
2. RTC error
1. Ensure that the keybo ard and
mouse are connected
correctly.
2. Replace the RTC battery.
Initial Keyboard
Table of Contents
Section 1 Introduction
Package Contents ...................................................... 1-1
Intel Pentium 4 Processors......................................... 1-2
Chipset Components.................................................. 1-2
Accelerated Graphics Port ......................................... 1-3
Ultra ATA66/100 ........................................................ 1-3
Hardware Monitoring................................................. 1-3
LAN (Optional) .......................................................... 1-3
Serial ATA.................................................................. 1-4
IEEE 1394 (Optional) .................................................. 1-4
Mainboard Form-Factor .............................................1-5
I/O Shield Connector.................................................. 1-6
Power-On/Off (Remote) .............................................. 1-6
System Block Diagram ............................................... 1-7
Section 2 Features
Mainboard Features ................................................... 2-1
Section 3 Installation
Mainboard Layout ..................................................... 3-2
Easy Installation Procedure
CPU Installation ......................................................... 3-3
Jumper Settings.......................................................... 3-5
System Memory Configuration.................................. 3-6
Expansion slots ..........................................................3-9
Device Connectors..................................................... 3-11
External Modem Ring-in Power ON and
Keyboard Power ON Function (KBPO) ..................... 3-18
STR (Suspend To RAM) Function ..........................3-19
Supports AGP Card 3.3V Protection ..........................3-20
Page
Section 4 Award BIOS Setup
Main Menu ................................................................ 4-1
Standard CMOS Setup ............................................... 4-2
Advanced BIOS Features .......................................... 4-3
Advanced Chipset Features ...................................... 4-7
Integrated Peripherals ................................................ 4-9
Power Management Setup ......................................... 4-17
PNP/PCI Configuration Setup.................................... 4-22
PC Health Status ........................................................ 4-24
Power BIOS Features ................................................. 4-26
Defaults Menu ........................................................... 4-30
Supervisor/User Password Setting ............................4-31
Exit Selecting .............................................................. 4-32
Section 5 Driver Installation
Easy Driver Installation.............................................. 5-1
C-Media Audio Configuration Brief Guide ................ 5-2
Appendix Appendix A
Update Your System BIOS .........................................A-1
Appendix B
EEPROM BOIS Remover ............................................ B-1
Appendix C
GHOST 7 Quick Users Guide (Optional) ................... C-1
Appendix D
POST Codes .............................................................. D-1
Page Left Blank
Introduction
Page 1-1
B
A
C
D
USERS
MANUAL
E
or
G
F
J
K
I
Section 1
INTRODUCTION
Package Contents
Contents
A.Mainboard
B. Users manual
C. Floppy drive cable
D. HDD drive cable or round cable
E. CD and diskette (drivers and
utilities)
F. Game port cable
G. I/O Shield
H. S-ATA data and power cable
Deluxe Pack Items
I. IEEE 1394 two port cable
Other Optional Items
J. USB2.0 port cable
K. S/PDIF Module
H
If you need the other optional item,
please contact dealer for assistance.
Introduction
Page 1-2
Intel
®
Pentium
®
4 processors
The Intel Pentium 4 processor, Intel's most advanced, most powerful processor for
desktop PCs and entry-level workstations, is based on Intel NetBurst
TM
microarchitecture. The Pentium 4 processor is designed to deliver performance
across applications and usages where end-users can truly appreciate and experience
the performance. These applications include Internet audio and streaming video,
image processing, video content creation, speech, 3D, CAD, games, multimedia, and
multi-tasking user environments. The Pentium 4 processor delivers this world-class
performance for consumer enthusiasts and business professional desktop PC users
as well as for entry-level workstation users.
Intel adds support for Hyper-Threading Technology to the Pentium 4 processor
family. HT Technology allows a single, physical Pentium 4 processor to function as
two logical processor for next generation multi threaded application.
For more information about all the new features the Pentium 4 delivers check out
the Intel website at http://www.intel.com
Chipset Components
This board is designed with Intel
®
865PE (Springdale-PE) chipset. The Intel
®
865PE
chipset consists of the Memory Controller Hub (MCH), the I/O Controller Hub
(ICH5/R).
!!
!!
! Memory Controller Hub (MCH)
The MCH provides the interconnect between the AGP, DDR SDRAM and the
system logic. It integrates:
- Supports for single processor with a data transfer rate of 400/533/800MHz.
- Supports dual channel of 266/333/400 DDR SDRAM up to 4GB.
- 8X/4X 1.5V AGP interface (Only support 1.5V on AGP interface).
- Downstream hub link for access to the ICH5/R.
!!
!!
! I/O Controller Hub (ICH5/R)
The I/O controller Hub provides the I/O subsystem with access to the rest of the
system. Additionally, it integrates many I/O functions:
Introduction
Page 1-3
- Upstream hub link for access to the MCH
- 2-Channel Ultra ATA/100 Bus Master IDE controller
- USB controller
- I/O APIC
- SMBus controller
- LPC / Flash BIOS interface
- PCI 2.3 interface
- Integrated System Management Controller
Accelerated Graphics Port (AGP)
The board provides the AGP 3.0 interface. The AGP interface can support external
AGP slot with AGP 8X/4X and Fast Write Transactions. The AGP Interface Specifi-
cation revision 3.0 enhances the functionality of the original AGP Interface Specifi-
cation by allowing 8X data transfers (8 data samples per clock) and 1.5 volt (Power
supply) operation. Supports Maximum AGP interface bandwidth 2.1GB/s. (1.5 volt
AGP Card supports only).
Ultra ATA/66/100
The ICH5/R provides an Ultra ATA/66/100 Bus Master IDE controller. This controller
supports Ultra ATA/66/100 protocols which are ideal for supporting demanding
applications such as real-time video, multimedia, and a high performance operating
system. A new IDE cable is required for Ultra ATA/66/100. This cable is an 80-pin
conductor cable, which is backwards compatible with ATA/33 connectors.
Hardware Monitoring
Hardware monitoring enables you to monitor various aspects of the system operation
and status. The features include CPU temperature, voltage and fan speed in RPMs.
LAN (Optional)
The motherboard mounts the LAN chipset. It allows the mainboard to connect to a
local area network by means of a network hub.
Introduction
Page 1-4
Serial AT A
The evolutionary serial ATA interface replaces the standard parallel ATA physical
storage interface. The serial ATA specification provides scalability and allows
future enhancements to the computing platform. Serial technology overcomes
performance limits of parallel interface architecture, meeting the escalating need for
faster data throughput in servers and storage devices.
Serial ATA is backward compatible with current software and runs on existing
architecture without modification. The serial ATA interface cable requires lower
voltages and uses smaller cable connectors, providing ease of installation. You can
easily upgrade storage devices that are compatible with the serial ATA interface
specification.
Serial ATA is completely software compatible with parallel ATA, requiring no
modification to your operating system.
IEEE1394 (Optional)
IEEE 1394 is a high-speed serial bus developed by Apple that allows users to
connect up to 63 devices to the serial bus on a PC. IEEE is sometimes called the
IEEE 1394 standard, the i.Link connector, FireWire, and the High Performance Serial
Bus (HPSB).
IEEE 1394 provides transfer rates up to 400Mbits/sec. IEEE 1394 provides enhanced
PC connectivity for consumer electronics audio/video (A/V) appliances, storage
peripherals, portable devices such as digital cameras, and inter-PC communications.
IEEE 1394 supports hot swapping, multiple speeds on the same bus, and isochro-
nous data transfer providing much needed bandwidth for multimedia operations.
Introduction
Page 1-5
Mainboard Form-Factor
The board is designed with ATX form factor - the latest industry standard of
chassis. The ATX form factor is essentially a Baby-AT baseboard rotated 90
degrees within the chassis enclosure and a new mounting configuration for the
power supply. With these changes the processor is relocated away from the
expansion slots, allowing them all to hold full length add-in cards. ATX defines a
double height aperture to the rear of the chassis which can be used to host a
wide range of onboard I/O. Only the size and position of this aperture is defined,
allowing PC manufacturers to add new I/O features (e.g.; TV input, TV output,
joystick, modem, LAN, audio, etc.) to systems. This will help systems integrators
differentiate their products in the marketplace, and better meet your needs.
By integrating more I/O down onto the board and better positioning the hard
drive and floppy connectors material cost of cables and add-in cards is
reduced.
By reducing the number of cables and components in the system, manufac-
turing time and inventory holding costs are reduced and reliability will
increase.
By using an optimized power supply, it's possible to reduce cooling costs
and lower acoustical noise. An ATX power supply, which has a side-
mounted fan, allows direct cooling of the processor and add-in cards making
a secondary fan or active heatsink unnecessary in most system applications.
PCI slots
Expandable I/O
Figure 2: Summary of ATX chassis features
CPU
Single chassis
fan for system
ATX
Power
Supply
ATX power connector
Floppy/IDE
connectors
AGP slot
3 1/2-inch
Bay
5 1/4-inch
Bay
ATX 12V power
connector
Introduction
Page 1-6
Power-On/Off (Remote)
The board has 20-pin ATX and 4-pin ATX12V connectors for power supplies
(Figure 4). For power supplies that support the Remote On/Off feature, this should
be connected to the mainboard front panel PW_ON connector for the computer
power On/Off button.
The board has been designed with Soft Off" function. You can turn off the system
two ways: pressing the front panel power On/Off button, using the "Soft Off"
function (incorporated in the mainboards onboard circuit controller) that can be
controlled by an operating system such as Windows
®
XP/ME/2000/98/95.
Note: For maintaining the DDR SDRAM power during STR (ACPI S3) function, it is
strongly recommend to use power supplies that have a +5VSB current of (>=)
2A. Please check the 5VSBs specification that has been printed on the power
supplys outer case.
Note: The board requires a minimum of 250 Watt power supply to operate. Your
system configuration (amount of memory, add-in cards, peripherals, etc.) may
exceed the minimum power requirement but to ensure that adequate power is
provided, use a 300 Watt (or greater) power supply.
I/O Shield Connector
The board is equipped with an I/O back panel (Figure 3). Ensure that your computer
case has the appropriate I/O cutout.
Figure 3: I/O ports
PW-ON
Case (chassis) Power ON/OFF button (PW-ON)
POWER SUPPLY
12V 4-pin
20-pin
Figure 4: Simple ATX power ON/OFF controller
COM1
Parallel Port
RJ-45 LAN
(Optional)
USB2.0
ports
USB2.0
ports
PS/2
Mouse
PS/2
Keyboard
Mic-in/Center&Subwoofer (Pink)
Line-out/Front out (Green)
Line-in/Rear out (Blue)
Introduction
Page 1-7
Figure 5: System Block Diagram
System Block Diagram
Introduction
Page 1-8
Page Left Blank
.A=JKHAI
Page 2-1
Section 2
FEATURES
Mainboard Features
Processor
!
Socket 478 Intel
®
Pentium
®
4 processor.
Supports Northwood, Prescott or later CPU only, does not support
Willamette CPU.
!
Supports System Bus and Memory Configurations:
FSB400 / DDR266 (PC2100)
FSB533 / DDR266/333 (PC2100/PC2700)
FSB800 / DDR333 (PC2700)
FSB800 / DDR400 (PC3200)
* When configured to FSB800/DDR333, adaptive synchronization aligns to the
closest FSB to memory clock ratio, setting memory channel to 320MHz.
!
Supports Hyper-Threading Technology
Enabling the functionality of Hyper-Threading Technology for your
computer system requires ALL of the following platform Components:
"CPU: An Intel
®
Pentium
®
4 Processor with HT Technology.
"Chipset: An Intel
®
Chipset that supports HT Technology.
"BIOS: A BIOS that supports HT Technology and has it enabled.
"OS: An operating system that supports HT Technology.
Chipset
!
Intel 865PE Chipset (865PE + ICH5R or ICH5)
Main Memory
!
Four 184-pin DDR DIMM sockets for PC2100/2700/3200 (DDR266/333/400)
DIMMs
!
Supports 128-bit dual channel memory architecture
!
Supports up to 4GB memory size
.A=JKHAI
Page 2-2
BIOS
!
Flash EEPROM with Award BIOS
- ACPI v2.0 compliant
- S3 (Suspend to DRAM) sleep-state support
- SMBIOS (System Management BIOS)
v2.2 compliant
- Supports Power failure recovery
- Capable to waked the computer up from specific states by LAN, Power
switch, PME#, RTC alarm, USB, PS2 K/B, PS2 Mouse, Modem Ring-in
COM#1
Onboard PCI Devices
! 1394 --> Integrate 1394 controller with Agere FW323 for 3 ports solution
- IEEE-1394a compliant with up to 400Mbps bandwidth
! S-ATA --> Up to four Serial ATA devices ( 2 for optional by Silicom Image
SIL3112A)
- Suppoers Serial ATA devices with up to 1.5Gbps bandwidth
! LAN --> Integrate 10/100Mps Fast Ethernet controller with Broadcom
BCM4401 LAN Chipset
Integrate 1Gbps Fast Ethernet controller with Broadcom
BCM5705/5788 LAN Chipset (for high-level model only)
! IDE --> 2 IDE Port with PIO/Ultra DMA-33/66/100 up to 4 devices
2 Extra IDE Port by HPT372 with Ultra DMA-133 & IDE RAID
up to 4 devices (Optional)
Legacy IO Controller
! Winbond W83627HF LPC IO controller with floppy, printer, game, serial
and CIR/SIR interface
Audio
! Six channel audio with analog and digital output using CMI9739A AC97
CODEC
- AC97 v2.2 compliant
(Optional)
(Optional)
.A=JKHAI
Page 2-3
- In 2-CH mode, supports Line-In (Blue), Line-Out (Green) and Mic-In
(Pink) at rear panel
- In 6-CH mode, supports Rear speaker out (Blue), Front speaker out
(Green) and Center&Subwoofer speaker out (Pink) at rear panel
- Supports CD-In, Aux-In and S/PDIF-In/out interface
- Supports Line-out and Mic-In for front panel
Peripheral Interfaces
! PS/2 keyboard and mouse ports (at rear panel)
! One Parallel (printer) port (at rear panel)
! Two Serial ports (1 at rear panel)
! Eight USB2.0 ports (4 at rear panel)
! One RJ45 LAN connector (at rear panel)(Optional)
! One game port
! One floppy drive interface
! Two IDE interfaces
! Two IDE&RAID interfaces (Optional)
! Three 1394 interface (Optional)
! Four Serial ATA interface (2 for Optional)
! Three Fan connectors
Front Panel Controller
! Supports Reset & Soft-Off switches
! Supports HDD & Power LEDs
! Supports PC speaker
Expansion Slots
! One AGP slots supporting 1.5v 4X/8X AGP card
- AGP v3.0 compliant
! Five PCI bus sockets
with Bus Master support
- PCI v2.3 compliant
.A=JKHAI
Page 2-4
Other Features
! Magic Health  a H/W monitoring software utility, for voltages, tempera-
tures and fan-speeds sensing
! EZ Boot  An easy way let end-user can choose to boot from hard drive,
CD-ROM, floppy, 
! Supports exclusive KBPO (Keyboard Power On) function
! Excellent Over clocking capabilities by
- subtle voltage tuning on CPU, Memory, AGP
- subtle frequency tuning on FSB
- Supports complete FSB/Memory and FSB/AGP, PCI Asynchronous
scheme for over-clocking
! Supports AGP card 3.3V Protection
! P80P for system debugging
Form Factor
! 305 x 245 mm ATX size
Installation
Page 3-1
Section 3
INSTALLATION
Installation
Page 3-2
Mainboard Layout
Installation
Page 3-3
Easy Installation Procedure
The following must be completed before powering on your new system:
3-1. CPU Installation
3-2. Jumper Settings
3-3. System Memory Configuration
3-4. Expansion Slots
3-5. Device Connectors
3-1 CPU Installation
Step 1
Open the socket by raising the actuation
lever.
Figure 1
Step 2
Align pin 1 on the CPU with pin 1 on
the CPU socket as shown in the
illustration above. The CPU is keyed to
prevent incorrect insertion. Dont force
the processor into the socket. If it does
not go in easily, check for mis-orienta-
tion and reinsert the CPU.
Make sure the processor is fully
inserted into the socket.
Figure 2
Pin 1
Installation
Page 3-4
Figure 3
Step 4
Apply thermal compound to the top of
the CPU and install the heatsink as
shown.
Step 5
Install the cooling fan assembly. Press
the two clips in the direction of the
arrows shown in Figure 5 to secure the
assembly to the CPU socket.
Step 6
Plug the CPU fan into the CPU fan
connector.
The installation is complete.
Figure 4
Figure 5 Figure 6
NOTES:
Damage to Intel Pentium
TM
4 processors might result if installed with
incorrect CPU fan and heatsink assemblies. Use Intels design thermal
solution shown in the illustrations above: an active heatsink; an extruded
aluminum heatsink base; and a fan attached to the top on the fin array.
Apply heatsink thermal compound or paste to the CPU to avoid CPU
overheating and damage.
In accordance with Intel Corp. specifications, do not install a CPU over
50 times to avoid bending the pins and damaging the CPU.
Step 3
Close the socket by lowering and
locking the actuation lever.
Installation
Page 3-5
3-2 Jumper Settings
JCMOS:
Settings:
1-2: Normal (Default)
2-3: Clear CMOS
Clear CMOS data Jumper
If the CMOS data becomes corrupted or you
forgot the supervisor or user password,
clear the CMOS data to reconfigure the
system back to the default values stored in
the ROM BIOS.
To CMOS Clear data, please follow the steps below.
1. Turn off the system.
2. Change the jumper from 1-2 to 2-3 position
for a few seconds.
3. Replace the jumper on to the 1-2 position.
4. Turn of the system and hold down the <Del>
key to enter BIOS setup.
Installation
Page 3-6
<Figure 6>
<Table 1>
3-3 System Memory Configuration
Memory Layout
The mainboard accommodates four PC2100/PC2700/PC3200 184-pin DIMMs (Dual In-
line Memory Modules):
Supports up to 4.0GB of 266/333/400MHz DDR SDRAM.
Supports two 64-bit wide DDR data channels.
Available bandwidth up to 3.2GB/s (DDR400) for single-channel mode and
6.4GB/s (DDR400) in dual-channel mode.
Supports non ECC DIMMs.
Registered DIMMs not supported.
Supports 128-Mb, 256-Mb, 512Mb DDR technologies.
Supports only x8, x16, DDR devices with four banks.
SPD (Serial Presence Detect) scheme for DIMM detection support.
Supports configurations defined in the JEDEC DDR1 DIMM specification
only.
Figure 6 and Table 1 show several possible memory configurations.
MMID1
)tib-46(
MMID2
)tib-821(
MMID3
)tib-46(
MMID4
)tib-821(
1#MMID
)kcalB(
SD/SSSD/SSSD/SSSD/SSSD/SS
2#MMID
)neerG(
SD/SSSD/SSSD/SSSD/SSSD/SS
3#MMID
)kcalB(
SD/SSSD/SSSD/SSSD/SS
4#MMD
)neerG(
SD/SSSD/SSSD/SSSD/SS
* SS: Single-Sided DIMM, DS: Double-Sided DIMM
DDR-A1 DIMM 1 (Black)
DDR-A2 DIMM 2 (Green)
DDR-B2 DIMM 4 (Green)
Dual Channel 2
Channel A
Channel B
Dual Channel 1
Installation
Page 3-7
NOTES:
When FSB is 400MHz, the mainbaod can support DDR266.
When FSB is 533MHz, the mainbaod can support DDR266/333.
When FSB is 800MHz, the mainbaod can support DDR333/400 (Uses DDR333,
adaptive synchronization aligns to the closest FSB to memory clock ratio, setting
memory channel to 320MHz)
The four DIMM sockets are divided into 2 Channels - Dual Channel 1
(DIMM1 and DIMM3) and Dual Channel 2 (DIMM2 and DIMM4), The same
dual channel has same color as show in Figure 6, Only in keeping those
DIMMs in same type and same size are preferred. We recommend you to use
the same color DIMM sockets to obtain the best memory performance.
- For one DIMM memory configuration, the DIMM can be located on either
of DIMM#1 to DIMM#4 in 64-bit mode.
- For two DIMMs memory configuration, they are prefer to located in same
group so the system can perform 128-bit mode.
- For three DIMMs memory configuration, the DIMMs can be located on all
DIMM sockets in 64-bit mode.
- For four DIMMs memory configuration, the DIMMs can be located on all
DIMM sockets in 128-bit mode.
Using non-compliant memory with higher bus speeds (overclocking) may
severely compromise the integrity of the system.
Installation
Page 3-8
DIMM Module Installation
Figure 8 displays the notch on the DDR DIMM memory module.
DIMMs have 184 pins and one notch that matches with the DDR DIMM socket.
DIMM modules are installed by placing the chip firmly into the socket and
pressing straight down as shown in figure 9 until the white clips close and the
module fits tightly into the DIMM socket (figure 10).
Figure 8 - DIMM notch
Figure 10 - DIMM module clip after installation
To remove the DIMM module press down the white clips and the module is
released from the socket.
Figure 9 - DIMM module clips before installation
CENTER KEY ZONE
(2.5 V DRAM)
Installation
Page 3-9
3-4 Expansion Slots
Installing an Expansion Card
The steps below assume that the mainboard is already installed in the system chassis.
1. Make sure the PC and all other peripheral devices connected to its has been
powered down.
2. Disconnect all power cords and cables.
3. Remove the system unit cover.
4. Remove the bracket of the slot that you intend to use. (You need to remove the
screw in order to remove the bracket.)
5. Align the card above the slot then press it down firmly until it is completely
seated in the slot.
6. Secure the card to the chassis with the screw you removed in step 4.
7. Replace the system unit cover.
8. Power on the PC.
9. Enter the BIOS step program to make the necessary settings.
10. Save the settings and restart the PC.
11. Install the software drivers of the expansion cards, if necessary.
AGP Slot
The mainboard is equipped with an AGP
slot. Make sure you install a card that
supports the 1.5V specification.
PCI Slots
The mainboard is equipped with 5 PCI
slots. It supports PCI cards that comply
with the PCI specification.
PCI Slots
AGP Slot
Installation
Page 3-10
AGP Card Installation Caution
1. AGP card component is blocked
by DIMM socket lock.
2. AGP slot lock is not locked.
3. AGP card edge connector is not
inserted properly.
1. AGP card component is not
blocked by DIMM socket lock.
2. AGP slot lock is locked.
3. AGP card edge connector is
inserted properly.
1. AGP slot lock is not locked.
2. AGP card edge connector is not
inserted properly.
1. AGP slot lock is locked.
2. AGP card edge connector is
inserted properly.
Installation
Page 3-11
GND
PME
+5V Standby
JCPU_FAN / JPWR_FAN / JSYS_FAN:
CPU/Power/Chassis Fan Power Connectors
JCPU_FAN: The CPU must be kept cool by using a
fan with heatsink.
JPWR_FAN: If you are installing an additional fan in
the unit, connect the fans connector.
JSYS_FAN: The chassis fan will provide adequate
airflow throughout the chassis to prevent overheat-
ing the CPU.
WOL1: WOL (Wake On LAN) Connector
Reserved for an NIC (Network Interface
Card) to wake the system.
Ground
+12V
Sence
JCPU_FAN
Figure 11 - I/O Ports
3-5 Connectors
JCPU_FAN
Ground
+12V
NC
JPWR_FAN
Ground
+12V
Sence
JSYS_FAN
JPWR_FAN
JSYS_FAN
COM1
Parallel Port
RJ-45 LAN
(Optional)
USB2.0
ports
USB2.0
ports
PS/2
Mouse
PS/2
Keyboard
Mic-in/Center&Subwoofer (Pink)
Line-out/Front out (Green)
Line-in/Rear out (Blue)
Loading...
+ 67 hidden pages