Integra DTM-5.3 User Manual

4.5 (2)

AV Receiver

DTM-5.3

Instruction Manual

Thank you for purchasing the Integra AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Contents

 

Before using

 

Important Safeguards..........................

2

Precautions ...........................................

3

Features.................................................

4

Supplied accessories ...........................

4

Facilities and connections

 

Remote controller description ............

5

Front panel description........................

6

Rear panel description ........................

8

Connecting components .................

10

Connecting speakers ........................

12

Connecting antennas .......................

13

Connecting the remote zone

 

(Zone 2) ............................................

14

Operating components not

 

reached by the remote

 

controller signals (IR IN/OUT) ..........

15

Connecting the power......................

16

Installing the remote controller

 

batteries ...........................................

17

Setup and operation

 

Basic operations .................................

18

Receiving stations ..............................

20

Entering station names ......................

23

Recording a source ...........................

24

Using Tape 2 Monitor .........................

26

Enjoying music in the remote zone...

27

Remote controller

 

Using the remote controller...............

28

Controlling other components .........

29

Appendix

Troubleshooting guide.......................

31

Specifications ..........

back cover page

PORTABLE CART WARNING
S3125A

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

 

AVIS

RISK OF ELECTRIC SHOCK

 

RISQUE DE CHOC ELECTRIQUE

DO NOT OPEN

 

NE PAS OUVRIR

 

 

 

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important Safeguards

1.Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions – The safety and operating instructions should be retained for future reference.

3.Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions – All operating and usage instructions should be followed.

5.Cleaning – Unplug the appliance from the wall outlet before cleaning. The appliance should be cleaned only as recommended by the manufacturer.

6.Attachments – Attachments not recommended by the manufacturer may create hazards. Use only recommended attachments.

7.Water and Moisture – Do not use the appliance near water –for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8.Accessories – Do not place the appliance on an unstable cart, stand, tripod, bracket, or table.The appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the appliance. Any mounting of the appliance should fol-

low the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

10.Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the appliance and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the appliance on a bed, sofa, rug, or other similar surface. The appliance should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. There should be free space of at least 20 cm (8 in.) and an opening behind the appliance.

11.Power Sources – The appliance should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company.

12.Grounding or Polarization – The appliance may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13.Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the appliance.

14.Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the appliance, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1.

15.Lightning – For added protection for the appliance during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the appliance due to lightning and power-line surges.

16.Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17.Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

18.Object and Liquid Entry – Never push objects of any kind into the appliance through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance.

19.Servicing – Do not attempt to service the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20.Damage Requiring Service – Unplug the appliance form the wall outlet and refer servicing to qualified service personnel under the following conditions:

A.When the power-supply cord or plug is damaged

B.If liquid has been spilled, or objects have fallen into the appliance

C.If the appliance has been exposed to rain or water

D.If the appliance does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to its normal operation.

E.If the appliance has been dropped or damaged in any way, and

F.When the appliance exhibits a distinct change in performance – this indicates a need for service.

2

21.Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22.Safety Check – Upon completion of any service or repairs to the appliance, ask the service technician to perform safety checks to determine that the appliance is in proper operating condition.

23.Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

24.Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

25.Liquid Hazards – The appliance shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the appliance.

FIGURE 1:

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

 

ANTENNA

 

LEAD IN

 

WIRE

GROUND

 

CLAMP

 

 

ANTENNA

 

DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC

 

SERVICE

 

EQUIPMENT

GROUNDING CONDUCTORS

 

 

(NEC SECTION 810-21)

 

GROUND CLAMPS

 

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

NEC – NATIONAL ELECTRICAL CODE

(NEC ART 250, PART H)

S2898A

 

Precautions

1. Recording Copyright

Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder.

2. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If power does not come on, contact your Integra/Onkyo authorized service station.

3. Care

From time to time you should wipe the front and rear panels and the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak solution of mild detergent and water, wring it out dry, and wipe off the dirt. Following this, dry immediately with a clean cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area in which this unit will be used meets the required voltage (e.g., AC 120 V, 60 Hz) written on the rear panel.

Setting the Standby/On button to standby does not shut off the power completely. The power cord should be removed from the AC outlet when the unit is not used for a prolonged period of time.

For U.S. model

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

For Canadian model

For models having a power cord with a polarized plug: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, THEN FULLY INSERT.

NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

Modèle pour les Canadien

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

3

Features

Power output

100 watts per channel, min RMS, at 8 ohms, both channels driven from 20 Hz to 20 kHz, with no more than 0.08% THD

Discrete output stage circuits for true high-current, low-impedance drive

Costly, high-quality parts such as large power transistors, an oversized isolated transformer and heavyduty extruded heat sink make it possible to accurately and effortlessly drive 4-ohm speakers (rare for a receiver)

A-BUS Ready

4 Audio and 2 AV inputs

A-B Speaker selector and outputs

Video and cassette tape dubbing capability

Direct tone control

40 FM/AM random presets

Preset scan tuning

Direct access tuning

Motor-driven, precision volume control

Headphone jack

Audio mute, sleep timer (via remote)

Battery-free rotary volume knob

New non-resonant feet

New slip-free rotary volume knob

Compatible remote control

Memory Preservation

This unit does not require memory preservation batteries. A built-in memory power back-up system preserves the contents of the memory during power failures and even when the unit is unplugged. The unit must be plugged in order to charge the back-up system.

The memory preservation period after the unit has been unplugged varies depending on climate and placement of the unit. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been unplugged. This period is shorter when the unit is exposed to a highly humid climate.

Supplied accessories

Check that the following accessories are supplied with the DTM-5.3.

Remote controller RC-477S (1)

 

Batteries (AA, R6 or UM-3) (2)

Power cord (1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AM loop antenna (1)

FM indoor antenna (1)

4

Facilities and connections

Remote controller description

Note: When you use the buttons that apply to specific mode (i.e., DVD mode, RCVR/Tape mode, or CD mode), you must press the corresponding mode button first.

Standby () button

This button sets the unit to Standby mode.

On ( ) button

This button turns on the power to the unit.

Scan button

Press this button to scan the preset channels.

Preset buttons

These buttons enable you to select an FM/AM preset channel.

Number (1–9, 0/10) buttons

When using RCVR/Tape mode, use these buttons to program and select the radio presets.

When using CD or DVD mode, use these buttons to select tracks and chapters.

Alphabetic letters/symbols buttons (RCVR/Tape mode)

Use these buttons to name the preset channels using characters.

DRCT Tune (Direct Tuning) button (RCVR/Tape mode)

Use this button to set the frequency. After pressing this button, use the number buttons to input the frequency.

+10 button (CD or DVD mode)

This button is used as a numeric key to control the Integra/ Onkyo CD or DVD player connected by using the terminals.

Top Menu button (DVD mode)

Press this button to display the top menu screen of a DVD.

Memory button (RCVR/Tape mode)

This button enables you to program or erase preset FM/AM stations.

/ / / / Enter buttons (DVD mode)

Use these cursor buttons to move the cursor to select an item on the display, and press the Enter button to confirm the setting.

Tuning Down / Tuning Up buttons (RCVR/Tape mode)

Use these buttons to change the tuner frequency. The tuner frequency is displayed in the front display and it can be changed in 100 kHz increments for FM and 10 kHz increments for AM.

When FM is selected, you can hold down one of the tuning buttons and then release it to activate the auto-search feature. It will search for a station in the direction of the button you pressed and stop when it tunes into one.

Return button (DVD mode)

Press this button while the setup screen is displayed to go back to the previous item.

SP A button (RCVR/Tape mode)

This button switches Speaker A On or Off.

Tape, CD, DVD operation buttons

These buttons enable you to control other Integra/Onkyo products connected to the DTM-5.3 via connection.

Direct button

This button enables the function that makes the input source sound much closer to the original sound source.

Input Selector buttons

These buttons enable you to select input sources.

Muting button

This button temporarily lowers the sound volume.

/ (Power) button (CD or DVD mode)

This button switches between On and Standby mode of a DVD or CD player connected to the DTM-5.3 via the connection.

Receiver/Tape, CD, DVD mode selection buttons

These buttons enable you to select a device you wish to control from the DTM-5.3 remote controller.

Sleep button

This button sets the sleep time. If the Sleep function is set, the power to the unit will be turned off automatically after the specified time.

Dimmer button

This button sets the brightness of the display on the front panel of the unit to “Normal,” “Dark,” or “Darker.”

Character button (RCVR/Tape mode)

Press this button to name the radio stations programmed in the preset memory using characters.

Disc button (CD or DVD mode)

Use this button to select a disc to play on a connected CD or DVD changer.

Menu button (DVD mode)

Press this button to display the menu screen.

FM Mode button (RCVR/Tape mode)

Use this button to set Stereo Mode to Mono if the FM stereo radio signal being received is frequently interrupted or contains lots of noise. Pressing the button each time will toggle between AUTO and MONO for STEREO MODE.

Setup button (DVD mode)

Press this button to display or quit a setup screen.

SP B button (RCVR/Tape mode)

This button switches Speaker B On or Off.

Zone 2, Off buttons

These buttons enable you to select the source for Zone 2. To turn off the Zone 2 output, press the Off button.

Volume buttons

These buttons adjust the volume level.

5

Integra DTM-5.3 User Manual

Front panel description

This section identifies and explains the controls and displays on the front panel of the DTM-5.3.

Front panel

Master Volume

Standby/On

1 ABC

2 DEF

3 GHI

 

 

 

 

4 JKL

5 MNO

6 PQR

 

7 STU

8 VWX

9 YZ-

Standby

 

 

 

 

Direct Tuning

0/10 /

Scan

Speakers

A B

Clear

Zone 2

Off

Display

 

Direct

 

Tuning

 

Memory

FM Mode

Character

 

 

Phones

 

 

 

Tape 2

 

 

 

 

 

Bass

Treble

Balance

 

DVD

Video

Monitor

Tape 1

FM

AM

Phono

CD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L

R

 

 

 

 

 

 

 

 

 

 

 

DTM-5.3

Display

A B

C

D

E

F G

H

I

 

SPEAKERS A B

AUDIO MUTE

FM MUTE

TUNED

MEMORY

 

STEREO

T-2 MONITOR

 

ON OFF

STEREO

 

SLEEP

MODE

 

 

 

 

 

AUTO

 

 

 

 

 

 

MONO

 

 

 

kHz

 

 

 

 

 

 

MHz

 

CH MIN

J

Standby/On button

Press this button to turn on the power to the DTM-5.3. The display indicators light up. Press the button again to set the unit in Standby mode, in which the display indicators turn off and no control on the unit is available.

If the main room device is in Standby mode, you can adjust the zone 2 room.

Standby indicator

This indicator lights up in Standby mode and when the unit receives a signal from the remote controller.

Zone 2 button and indicator, Off button

This button enables you to enjoy music in another room (Zone 2). When you press the Zone 2 button, the currentlyselected playback source for Zone 2 appears on the display. If “Z2 SRC” appears, the source for Zone 2 is the same as the currently-selected playback source. To change the source for Zone 2, press the Zone 2 button, then press an input selector button within five seconds. The Zone 2 indicator lights up. To select “Z2 SRC” for Zone 2, press the Zone 2 button twice. To turn off the Zone 2 output, press the Off button. The Zone 2 indicator turns off.

Remote control sensor

Display

A.STEREO MODE, AUTO, MONO indicator

Pressing the FM Mode button each time toggles between AUTO and MONO indicators.

B.T-2 MONITOR indicator

This indicator lights up when you press the Tape 2 Monitor button, which enables you to monitor the audio signal during recording to a three-head cassette tape deck connected to the TAPE 2 jack.

C.SPEAKERS A B indicator

This indicates which speaker system you are currently using.

D.AUDIO MUTE indicator

This indicator flashes while you are using the Mute function.

E.FM MUTE ON OFF indicator

Pressing the FM Mode button each time toggles between ON and OFF.

6

Front panel description

F.TUNED indicator

This indicator lights up when the unit receives a radio station signal

G.STEREO indicator

The indicator lights up when the unit receives an FM stereo radio station signal.

H.MEMORY indicator

The indicator lights up when you press the Memory button to program a radio station.

I. SLEEP indicator

This indicator lights up while the Sleep function is active.

J.Multi function display indicator

This display indicates the input source, frequency, preset number, and preset name.

Direct Tuning button

Use this button to set the frequency. After pressing this button, use the number buttons to input the frequency.

Number (1–9, 0/10) buttons

Use these buttons to program preset channels or select radio stations.

Alphabetic letters/symbols buttons

Use these buttons to name the preset channels using characters.

Scan button

Press this button to scan the preset channels.

Master Volume dial

This dial adjusts the volume level.

Balance dial

In general, set this dial to the center (12 o’clock) position. Adjust the dial accordingly if the left and right volume levels are not balanced, depending on the speaker position or listening position. Turn the dial clockwise to pan the stereo position to the right, and turn it counterclockwise to pan to the left.

Treble dial

This dial adjusts the high range of the left and right speakers. Turning the dial to the right from the center position will emphasize the high range, and turning it to the left will attenuate the high range.

Bass dial

This dial adjusts the low range of the left and right speakers. Turning the dial to the right from the center position will emphasize the low range, and turning it to the left will attenuate the low range.

Character button

Press this button to name the radio stations programmed in the preset memory using characters.

Memory, FM Mode buttons

Memory

Memory button enables you to program or erase preset FM/ AM stations.

FM Mode

Use FM Mode button to set Stereo Mode to Mono if the FM stereo radio signal being received is frequently interrupted or contains lots of noise. Pressing the button each time will toggle between AUTO and MONO for STEREO MODE.

Clear

To erase the programmed stations, hold down the Memory button, then press the FM MODE button.

Tuning buttons

Use these buttons to change the tuner frequency. The tuner frequency is displayed in the front display. It can be changed in 100 kHz increments for FM and 10 kHz increments for AM.

When FM is selected, you can hold down one of the tuning buttons and then release it to activate the auto-search feature. It will search for a station in the direction of the button you pressed and stop when it tunes one in.

Input selector buttons

These buttons enable you to select input sources.

To select input sources for the Zone 2 device, first press the Zone 2 button, then press an Input selector button.

Direct button and indicator

This button enables the function that makes the input source sound much closer to the original sound source. When you press this button, the indicator lights up, and the input source signal bypasses the Bass and Treble control circuits. In this way, the audio sounds more real and true to the original source.

To cancel this function, press this button again.

Display button

This button switches the display indication between the frequency value and the channel name if the FM and AM preset channels have been named.

Speakers A, B buttons

These buttons turn speaker systems A and B On and Off.

Phones

Connect a stereo headphone set to this standard stereo jack. Audio signals to the left and right speakers will be output to the headphones.

7

Rear panel description

This section identifies and explains how to use the terminals found on the rear of the DTM-5.3. Before connecting your audio and video components, be sure to read this section carefully and then proceed to the explanations on how to connect each individual component (see page 10).

 

 

 

 

 

 

 

ZONE 2

12V

 

 

 

 

 

 

 

IR OUT 40K

 

 

OUT

TRIGGER

IR

SPEAKER IMPEDANCE

ANTENNA

ZONE 2

IR OUT B

 

ZONE 2

DC IN

L

ZONE 2

 

IN

 

SELECTOR

 

CONTROL

 

OUT

24V 1A

 

SET BEFORE POWER ON

 

SELECTOR

56K

 

 

 

 

OUT

IN

 

A OR B :

A OR B : 4 OHMS MIN.

 

 

 

 

 

 

 

 

 

 

OUT

AM

A-BUS

IR

 

 

 

 

 

 

 

8 OHMS MIN.

/SPEAKER

 

 

 

 

 

 

 

 

/SPEAKER

A + B : 8 OHMS MIN.

 

 

 

A

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

/SPEAKER

 

 

 

 

 

 

 

 

 

 

 

 

AC INLET

FM

 

SUBWOOFER

MONITOR

DVD

VIDEO

 

 

SPEAKERS

 

75

 

 

 

 

GND

 

PRE OUT

OUT

IN

OUT

IN

 

 

A

 

B

 

 

 

 

 

 

 

 

 

REMOTE

 

 

 

 

V

 

 

 

 

CONTROL

 

 

 

 

AV RECEIVER

 

 

 

 

 

 

 

 

L

MODEL NO. DTM-5.3

 

 

 

 

 

 

 

 

RATING:

IN

IN

OUT

IN

OUT

IN

IN

OUT

IN

AC 120V 60 Hz 2.8A

AC OUTLET

L

 

 

 

 

 

 

 

L

AC 120V 60 Hz SWITCHED

 

 

 

 

 

 

 

120W 1 A MAX.

 

 

 

 

 

 

 

 

R

 

R

 

 

 

 

 

 

 

R

 

PHONO

CD

TAPE 1

TAPE 2

DVD

VIDEO

ANTENNA

These connectors enable you to connect the FM indoor antenna and AM loop antenna supplied with the DTM-5.3.

GND

Use this GND terminal to connect the ground (or earth) wire if a turntable is connected. Refer to “Connecting components” on page 10.

ZONE 2 CONTROL SELECTOR

This switch enables you to select whether the Zone 2 function is controlled from the A-BUS system or from the IR system. Sliding the switch to the left will select A-BUS system control, and sliding it to the right will select IR system control.

A-BUS READY

A-BUS is a simple, efficient, elegant audio distribution system. The wiring installation time is significantly reduced as only a single CAT-5 wire is run to each location. A-BUS is easy to use, reliable, affordable, and most of all, far better sounding than conventional auto former based volume controls.

ZONE 2 OUT: Use a CAT-5 (eight conductor twisted) cable to connect directly from the receiver’s A-BUS RJ45 Hub to an A-BUS keypad. A-BUS outputs enable connection of up to four A-BUS keypads.

Warning:

DO NOT connect ZONE 2 OUT to any computer or network connections (i.e., Ethernet). It will damage the computer or network components since 24-volt power runs on this cable to power the amplifier stages of the amplifier module.

IR OUT: Another feature of the A-BUS system is the ability to control source equipment in a room other than where the A-BUS module is installed. If you wish to control another source from the receiver at the A-BUS keypad by remote control, connect the A-BUS or another brand IR emitter on the receiver’s 40 K terminal. Then place the emitter on the remote receiver on the front panel.

Typically, the emitter will work when you connect with a 40 K connector. If it does not work, try a 56 K connector.

DC INPUT: Connect the A-BUS power supply. Do not use any other AC Adapter on this connector as it may cause severe damage to the receiver.

Note:

Don’t insert an A-BUS connector while Zone 2 or DTM5.3 is on.

ZONE 2 OUT

Connect the device that will be used in the remote zone (Zone 2). For more information on making the connections, refer to “Connecting the remote zone (Zone 2)” on page 14.

12V TRIGGER ZONE 2 OUT, IN terminal

These terminals are provided so that you can use the DTM- 5.3 to control another externally-connected device. Connect the component to this 1/8-inch mini-jack terminal. When the set input source is selected, the device will turn on. Set the 12V TRIGGER terminal using the Zone 2 mode.

When the DTM-5.3 is in Zone 2 mode, this terminal outputs at 12 V/100 mA.

IR IN/OUT

If the DTM-5.3 is located inside a rack or cabinet that will not allow infrared beams to reach the IR sensor, you will need to connect a remote sensor to IR IN input to be able to use the remote controller.

Then install the remote sensor in an unblocked location at which you can easily point the remote controller.

Using a mini-jack connector, connect the IR emitter to the IR OUT terminal on the DTM-5.3 and then place the IR emitter on the remote sensor of the component or facing it.

Refer to “Operating components not reached by the remote controller signals (IR IN/OUT)” on page 15.

SPEAKER IMPEDANCE SELECTOR

The DTM-5.3 provides two speaker system connections (SPEAKER A and SPEAKER B). Set the SPEAKER IMPEDANCE SELECTOR according to the impedance of speakers to be connected.

Warning:

Do not plug in the power cord during speaker system connection and operation of the SPEAKER IMPEDANCE SELECTOR.

8

Rear panel description

Depending on the impedance of the speakers used, set the SPEAKER IMPEDANCE SELECTOR on the rear panel as shown in the table.

Usable speaker impedance

Selector position

A or B speaker

4 ohms or higher/speaker

A and B speakers

8 ohms or higher/speaker

A or B speaker

8 ohms or higher/speaker

AC INLET

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.

Do not use a power cord other than the one supplied with the DTM-5.3. The power cord supplied is designed for use with the DTM-5.3 and should not be used with any other device.

Never disconnect the power cord from the DTM-5.3 while the other end is plugged into a wall outlet. Doing so may cause an electric shock. Always connect by plugging into the wall outlet last and disconnect by unplugging from the wall outlet first.

AC INLET

Power cord (supplied)

To an AC wall outlet

AC OUTLET

The DTM-5.3 is supplied with AC mains outlet for connecting the power cords from other devices so that their power is supplied through the DTM-5.3. By doing this, you can use the Standby/On button on the DTM-5.3 to turn on and off the connected devices as well.

Caution:

Make sure that the capacity of the other components connected to this unit does not exceed the 120 watts.

AC INLET

AC OUTLET

AC 120V 60 Hz SWITCHED

120W 1 A MAX.

Other component

SPEAKERS terminals

Connect the left and right speakers here.

VIDEO IN/OUT

The DTM-5.3 provides two video inputs and one video output. Connect a DVD player, VCR, or other video player to the input and connect a VCR or other video recorder to the output.

AUDIO IN/OUT

There are 6 audio inputs and 3 audio outputs for use with analog signals. The audio inputs and outputs require RCA type connectors.

When connecting a VCR or other video component, make sure you connect the audio and video leads together (i.e., both to VIDEO).

The PHONO jacks are designed for use with turntables that use moving magnet cartridges.

MONITOR OUT

This output enables you to connect to a television monitor.

SUB WOOFER PRE OUT

This terminal enables you to connect to an active subwoofer.

Note: The subwoofer can only operate when speaker system A is turned on.

REMOTE CONTROL

The terminal on the DTM-5.3 enables you to connect to other Integra/Onkyo components equipped with the same terminal. When a component is -connected, you can point the remote controller supplied with the DTM-5.3 at the sensor on the DTM-5.3 and operate that component without having to switch remote controllers.

In addition, by connecting components to the terminal, you can also perform the system operations given below.

Power on/ready function

When the DTM-5.3 is in Standby mode, if an -connected component is turned on, then the DTM-5.3 also turns on and the input source selected at the DTM-5.3 automatically switches to that component.

If the power cord for an -connected component is connected to the AC OUTLET on the DTM-5.3, or if the DTM- 5.3 is turned on, this function will not work.

Direct change function

When the play button is pressed on an -connected component, the input source selected at the DTM-5.3 automatically changes to that component.

Power off function

When the DTM-5.3 is placed in Standby mode, all -con- nected components are also automatically placed in Standby mode.

DTM-5.3

connector

Ex: Integra/Onkyo CD player

connector

Ex: Onkyo cassette tape deck

To connect components using the terminal, simply connect a remote control cable from this terminal to the terminal of the other component. An remote control cable with a 1/8-inch (3.5mm) miniature two-conductor plug comes with every cassette tape deck, compact disc player, MD recorder, and DVD player that has an terminal.

When performing operations with -connected components using the system, do not use the remote zone (Zone 2).

For remote control operation, the audio connection cables must also be connected.

If a component has two terminals, you can use either one to connect to the DTM-5.3. The other one can be used to daisy chain to another component.

9

Connecting components

This section explains how to connect the main components to the DTM-5.3 in the standard manner.

Be sure to always refer to the instruction manual that came with the component that you are connecting.

Do not plug in the power cord until all connections have been made.

For input jacks, red connectors (marked R) are used for the right channel, white connectors (marked L) are used for the left channel, and yellow connectors (marked VIDEO) are used for video connection.

Insert all plugs and connectors securely. Improper connections can result in noise, poor performance, or damage to the equipment.

Do not bind audio connection cables with power cords and speaker cables. Doing so may adversely effect the sound quality.

Audio connection cable

 

L (Left)

L

R (Right)

R

Video connection cable

 

Improper connection

Inserted completely

Example of audio equipment connection

ANTENNA

ZONE 2

 

CONTROL

 

SELECTOR

AM

A-BUS

IR

 

 

 

 

ZONE 2

OUT

IN

 

IR OUT 40K

 

 

OUT

 

 

IR OUT

B

ZONE 2

DC IN

L

Tape Deck

 

OUT

24V 1A

56K

 

 

 

 

 

 

 

 

R

(TAPE 1)

 

A

 

 

 

 

 

FM

 

SUBWOOFER

MONITOR

DVD

VIDEO

 

 

75

 

 

 

 

GND

 

PRE OUT

OUT

IN

OUT

IN

 

 

 

REMOTE

 

 

 

 

V

 

 

 

CONTROL

 

 

 

 

IN

IN

OUT

IN

OUT

IN

IN

OUT

IN

L

 

 

 

 

 

 

 

L

R

 

 

 

 

 

 

 

R

PHONO

CD

TAPE 1

TAPE 2

DVD

VIDEO

OUT

IN

Tape Deck

(TAPE 2)

: signal flow

Ground

OUT

OUT

 

Turntable

CD Player

 

(PHONO)

(CD)

10

Loading...
+ 22 hidden pages