Loading...
Form 04579652
Edition 2
June 2005
Air Percussive Hammer
114G and 114GQC
Product Information
Especificaciones del producto
Spécifications du produit
Save These Instructions
|
|
9 |
3 |
2 |
|
|
48h |
|
1 |
|
|
|
|
|
PMAX |
|
4 |
|
|
|
6 |
8 |
|
24h |
|
|
|
||
|
|
|
|
|
10 |
|
7 |
|
5 |
|
|
|
|
8h
(Dwg. 16576175)
1 |
2 |
3 |
5 |
6 |
9 |
10 |
|
I-R # - NPT |
|
I-R # - BS |
inch (mm) |
NPT |
I-R # |
I-R # |
cm3 |
C08-02-FKG0-28 |
C08-C2-FKG0 |
3/8 (10) |
1/4 |
10 |
10 |
3 |
|
|
|
|
9 inch-lbs |
|
4.0 ft-lbs |
|
|
|
|
|
|
|
|
|
|
> Ø 0.7” (17.78 mm)
.401
2 |
Form 04579652-Edition 2 |
Product Safety Information
Intended Use:
These Air Percussive Hammers are designed for hammering, punching, cutting, chipping and scraping material through repetitive application of linear impacts of a tool steel that is retained and driven by the Hammer.
For additional information refer to Air Percussive Tool Product Safety Information Manual Form 04581450.
Manuals can be downloaded from www.irtools.com
Prior to Use
WARNING
•Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel. Use only recommended lubricants.
•Use only proper cleaning solvents to clean parts. Use only cleaning solvents which meet current safety and health standards. Use cleaning solvents in a well ventilated area.
Tools are coated inside and out with rust-resisting oil before leaving the factory. Before using the tool, remove this oil by dipping the tool in a suitable cleaning solution to wash the oil from the exterior. Pour about 6 cm3 of a clean, suitable, cleaning solution into the air inlet and operate the tool for about 15 seconds. Dry the tool immediately after cleaning, pour 3 cm3 of Ingersoll-Rand No. 10 Oil into the air inlet and again operate the tool for 5 seconds to lubricate all working parts.
Product Specifications
|
|
Blows |
Stroke |
Sound Level dB (A) |
Vibration |
||
|
Type of |
Level |
|||||
|
Length |
(ISO15744) |
|||||
Model |
per |
(ISO8662) |
|||||
Handle |
|
|
|
||||
|
Minute |
|
|
|
|
||
|
|
Inch (mm) |
† Pressure (Lp) |
‡ Power (Lw) |
m/s2 |
||
|
|
|
|||||
114G |
Pistol Grip |
3,500 |
2-5/8 (67) |
98.3 |
109.3 |
11.3 |
|
114GQC |
Pistol Grip |
3,500 |
2-5/8 (67) |
98.3 |
109.3 |
11.3 |
|
|
|
|
|
|
|
|
|
† KpA = 3dB measurement uncertainty
‡ KwA = 3dB measurement uncertainty
Form 04579652-Edition 2 |
3 |
Installation and Lubrication
Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping, air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 16576175 and table on page 2.
Maintenance frequency is shown in circular arrow and defined as h=hours, d=days, and m=months. Items identified as:
1. |
Air filter |
6. |
Thread size |
2. |
Regulator |
7. |
Coupling |
3. |
Lubricator |
8. |
Safety Air Fuse |
4. |
Emergency shut-off valve |
9. |
Oil |
5. |
Hose diameter |
10. |
Oil - before starting, into air inlet |
Note: If the action of the tool becomes sluggish:
-Pour 3 cm3 of cleaning solution into air inlet and run tool for 30 seconds.
-Pour 3 cm3 of Oil into air inlet and run tool for 30 seconds.
Note: Before storing the tool or leaving idle exceeding 24 hours:
-Pour 3 cm3 of IR # 10 oil into air inlet and run tool for 5 seconds.
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that they can be recycled.
The original language of this manual is English.
Tool repair and maintenance should only be carried out by an authorized Service Center. Refer all communications to the nearest Ingersoll-Rand Office or Distributor.
4 |
Form 04579652-Edition 2 |
Loading...