● After using Emergency Tire Sealant to
repair a minor tire puncture, do not
drive the vehicle at speeds faster than
50 MPH (80 km/h).
● Immediately after using the Emergency
Tire Sealant to repair a minor tire puncture, take your vehicle to inspect, and
repair or replace the tire. It is recommended you visit an INFINITI retailer for
this service. The Emergency Tire Sealant cannot permanently seal a punctured tire. Continuing operation of the
vehicle without a permanent tire repair
can lead to a crash.
● INFINITI recommends using only Genuine NISSAN Emergency Tire Sealant
provided with your vehicle. Other tire
sealants may damage the valve stem
seal which can cause the tire to lose air
pressure. It is recommended you visit
an INFINITI retailer as soon as possible
after using tire repair sealant.
This vehicle does not have a spare tire. The
emergency tire puncture repair kit (Emergency
Tire Sealant) is supplied with the vehicle instead
of a spare tire. Itcan be used to temporarily repair
minor tire punctures.
If you have a flat tire, follow the instructions below.
CAUTION
● To avoid the emergency tire puncture
repair kit being damaged during storage or use:
– Only use the emergency tire puncture
repair kit on your vehicle. Do not use
it on other vehicles.
– Only use the kit to inflate the tires of
your vehicle and to check the vehicle’s tire pressure.
– Only plug the compressor into a 12V
DC car power point.
– Keep the kit free of water and dirt.
– Do not disassemble or modify the kit.
– Do not drop the kit or allow hard
impacts to the kit.
● Do not use the emergency tire puncture
repair kit under the following conditions. It is recommended you visit an
INFINITI retailer or professional road
assistance.
– when the sealant has passed its ex-
piration date (shown on the label attached to the bottle)
– when the cut or the puncture is ap-
proximately 0.25 in (6 mm) or longer
– when the tire sidewall is damaged
– when the vehicle has been driven
with extremely low tire pressure
– when the tire has come off the inside
or the outside of the wheel.
– when the tire wheel is damaged
– when two or more tires are flat
STOPPING THE VEHICLE
1. Safely move the vehicle off the road and
away from traffic.
2. Turn on the hazard warning flashers.
3. Park on a level surface and apply the parking
brake.
4. Move the shift lever to the P (Park) position.
5. Turn off the engine.
6. Raise the hood to warn other traffic and to
signal professional road assistance personnel that you need assistance.
7. Have all passengers get out of the vehicle
and stand in a safe place, away from traffic
and clear of the vehicle.
WARNING
● Make sure the parking brake is securely
applied and the transmission is shifted
into P (Park).
● Never repair tires when the vehicle is on
a slope, ice or slippery areas. This is
hazardous.
● Never repair tires if oncoming traffic is
close to your vehicle. Wait for professional road assistance.
JVM0722X
GETTING EMERGENCY TIRE
PUNCTURE REPAIR KIT
Take out the emergency tire puncture repair kit
located in the trunk. Remove the clips
the trunk trim as illustrated.
The repair kit consists of the following items:
● Tire sealant bottle
● Air compressor
● Speed restriction sticker
䊊
1
to open
BEFORE USING EMERGENCY TIRE
PUNCTURE REPAIR KIT
● If any foreign object (for example, a screw or
nail) is embedded in the tire, do not remove
it.
● Check the expiration date of the sealant
(shown on the label attached to the bottle).
Never use a sealant whose expiration date
has passed.
REPAIRING TIRE
WARNING
Observe the following precautions when
using the tire repair compound.
● Swallowing the compound is dangerous. Immediately drink as much water
as possible and seek prompt medical
assistance.
● Rinse well with lots of water if the compound comes into contact with skin or
eyes. If irritation persists, seek prompt
medical attention.
● Keep the repair compound out of the
reach of children.
NOTE:
Do not remove any nails or screws that
have penetrated the tire when performing
repairs.
JVE0014X
1. Take out the speed restriction sticker from
the air compressor*, then put it in a location
where the driver can see it while driving.
*: The compressor shape may differ depending
on the models.
CAUTION
Do not put the speed restriction label on
the steering wheel pad, the speedometer
or the warning light locations.
1
2. Take the hose
of the air compressor. Remove the cap of the
bottle holder from the air compressor.
and the power plug
䊊
SCE0868
2
out
䊊
SCE0869SCE0870SCE0871
3. Remove the cap from the tire sealant bottle,
and screw the bottle clockwise onto the
bottle holder. (Leave the bottle seal intact.
Screwing the bottle onto the bottle holder
will pierce the seal of the bottle.)
4. Remove the cap from the tire valve on the flat
tire.
A
5. Remove the protective cap
and screw the hose securely onto the tire
valve. Make sure that the pressure release
B
valve
that the air compressor switch is in the OFF
(O) position, and then insert its power plug
into the power outlet in the vehicle.
is securely tightened. Make sure
䊊
of the hose
䊊
6. Push the ignition switch to the “ACC” position. Then turn the compressor switch to the
ON (⫺) position and inflate the tire up to the
pressure that is specified on the tire and
loading information label affixed to the driver’s side pillar if possible, or to the minimum
of 26 psi (180 kPa). Turn the air compressor
off briefly in order to check the tire pressure
with the pressure gauge.
If the tire is inflated to higher than the specified
pressure, lower the tire pressure by releasing air
with the pressure release valve.
NOTE:
The compressor tire pressure gauge may
show a pressure reading of 87 psi (600 kPa)
for about 30 seconds while inflating the
tire. The pressure gauge is indicating the
pressure inside the sealant can. When the
sealant has been injected into the tire the
pressure gauge will drop and indicate actual tire pressure.
WARNING
● To avoid serious personal injury while
using the emergency tire puncture repair kit:
– Securely tighten the compressor
hose to the tire valve. Failure to do so
can cause the sealant to spray into
the air and get into your eyes or on
the skin.
● Do not stand directly beside the damaged tire while it is being inflated because of the risk of the rupture. If there
are any cracks or bumps, turn the compressor off immediately.
If the tire pressure does not increase to 26 psi
(180 kPa) within 10 minutes, the tire may beseriously damaged and the tire cannot be repaired with this tire puncture repair kit. It is
recommended you visit an INFINITI retailer for
servicing.
7. When the tire pressure is at the specified
amount, turn the air compressor off. If the
pressure cannot be inflated to the specified
amount, the air compressor can be turned
off at the minimum of 26 psi (180 kPa).
Remove the power plug from the power
outlet and quickly remove the hose from the
tire valve. Attach the protective cap and
valve cap. Properly stow the emergency tire
puncture repair kit in the trunk.
CAUTION
To avoid serious personal injury when
stowing the emergency tire puncture repair kit:
● Keep the sealant bottle screwed into
the compressor. Failure to do so can
cause the sealant to spray into the air
and get into your eyes or on the skin.
8. Immediately drive the vehicle for 10 minutes
or 2 miles (3 km) at a speed of 50 MPH
(80 km/h) or less.
9. After driving, make sure that the air compressor switch is in the OFF (O) position,
then screw the hose securely onto the tire
valve. Check the tire pressure with the pressure gauge. The temporary repair is completed if the tire pressure does not drop.
Make sure the pressure is adjusted to the
pressure that is specified on the tire and
loading information label before driving.
10. If the tire pressure drops, repeat the steps
from 5 to 9. If the pressure drops again or
under 19 psi (130 kPa), the tire cannot be
repaired with this tire puncture repair
kit. It is recommended you visit an INFINITI
retailer for this servicing.
The sealant bottle and hose cannot be re-
used to repair another punctured tire. It is
recommended you visit an INFINITI retailer
to purchase replacements.
CHECKING TIRE PRESSURE
AFTER REPAIRING TIRE
It is recommended you visit an INFINITI retailer for
tire repair/replacement as soon as possible.
WARNING
● After using Emergency Tire Sealant to
repair a minor tire puncture, do not
drive the vehicle at speeds faster than
50 MPH (80 km/h).
● Immediately after using Emergency Tire
Sealant to repair a minor tire puncture,
take your vehicle to inspect, and repair
or replace the tire. It is recommended
you visit an INFINITI retailer for this
service. The Emergency Tire Sealant
cannot permanently seal a punctured
tire. Continuing operation of the vehicle
without a permanent tire repair can lead
to a crash.
● INFINITI recommends using only Genuine NISSAN Emergency Tire Sealant
provided with your vehicle. Other tire
sealants may damage the valve stem
seal which can cause the tire to lose air
pressure. It is recommended you visit
an INFINITI retailer as soon as possible
after using tire repair sealant.
LDI0393
1. Remove the valve stem cap from the tire.
2. Press the pressure gauge squarely onto the
valve stem. Do not press too hard or force
the valve stem sideways, or air will escape. If
the hissing sound of air escaping from the
tire is heard while checking the pressure,
reposition the gauge to eliminate this leakage.
3. Remove the gauge.
4. Read the tire pressure on the gauge stem
and compare it to the specification shown
on the Tire and Loading Information label.
5. Add air to the tire as needed. If too much air
is added, press the core of the valve stem
briefly with the tip of the gauge stem to
release pressure. Recheck the pressure and
add or release air as needed.
6. Install the valve stem cap.
7. Check the pressure of all other tires, including the spare.
COLD
TIRE IN-
SIZE
FLATION
PRES-
SURE
FRONT
ORIGINAL
TIRE
P255/
40RF19
96V
245/
40RF19
94W
P245/
40RF19
240 kPa,
35 PSI
240 kPa,
35 PSI
240 kPa,
35 PSI
94V
TIRE CHAINS
REAR
ORIGINAL
TIRE
SPARE
TIRE (if so
equipped)
SIZE
P255/
40RF19
96V
265/
35RF19
94W
245/
40RF19
94W
P245/
40RF19
94V
T145/
70R18
107M
COLD
TIRE IN-
FLATION
PRES-
SURE
240 kPa,
35 PSI
240 kPa,
35 PSI
240 kPa,
35 PSI
240 kPa,
35 PSI
420 kPa,
60 PSI
CAUTION
Tire chains/cables should not be installed
on P255/40RF19 and 265/35RF19 tires.
Doing so will cause damage to the vehicle.
If you plan to use tire chains/cables, you
shouldinstall245/40RF19or
P245/40RF19 tires on your vehicle.
Use of tire chains may be prohibited according to
location. Check the local laws before installing
tire chains. When installing tire chains, make sure
they are the proper size for the tires on your
vehicle and are installed according to the chain
manufacturer’s suggestions. Use only SAEclass S chains. Class “S” chains are used on
vehicles with restricted tire to vehicle clearance.
Vehicles that can use Class “S” chains are designed to meet the SAE standard minimum clearances between the tire and the closest vehicle
suspension or body component required to accommodate the use of a winter traction device
(tire chains or cables). The minimum clearances
are determined using the factory equipped tire
size. Other types may damage your vehicle. Use
chain tensioners when recommended by the tire
chain manufacturer to ensure a tight fit. Loose
end links of the tire chain must be secured or
removed to prevent the possibility of whipping
action damage to the fenders or underbody. If
possible, avoid fully loading your vehicle when
using tire chains. In addition, drive at a reduced
speed. Otherwise, your vehicle may be damaged
and/or vehicle handling and performance may be
adversely affected.
Tire chains must be installed only on the
rear wheels and not on the front wheels.
Never install tire chains on a TEMPORARY USE
ONLY spare tire (if so equipped). Never install tire
chains on a punctured run-flat tire (if so
equipped), as this could damage your vehicle.
Do not use tire chains on dry roads. Driving with
tire chains in such conditions can cause damage
to the various mechanisms of the vehicle due to
some overstress.
WHEELS AND TIRES
Road wheel
TypeSizeOffset in (mm)
19 x 9J1.57 (40)
Conventional
Spare (if so equipped)18 x 4T0 (0)
Tire
TypeSizePressure PSI (kPa) [Cold]
Conventional
Spare (T-type) (if so equipped)T145/70R18 107M60 (420)
should first find out if the fuel available is suitable
for your vehicle’s engine.
Using fuel with too low an octane rating may
cause engine damage. All gasoline vehicles must
be operated with unleaded gasoline. Therefore,
avoid taking your vehicle to areas where appropriate fuel is not available.
When transferring the registration of your
vehicle to another country, state, province
or district, it may be necessary to modify the
vehicle to meet local laws and regulations.
The laws and regulations for motor vehicle emis-
sion control and safety standards vary according
to the country, state, province or district; therefore, vehicle specifications may differ.
When any vehicle is to be taken into another country, state, province or district and
registered, its modifications, transportation, and registration are the responsibility
of the user. INFINITI is not responsible for
any inconvenience that may result.
(3,1)
Foreword
CV37D1-8D14BA72-70E0-4F77-8469-7DEC8F6401D5
Your INFINITI represents a new way of
thinking about vehicle design. It integrates
advanced engineering and superior craftsmanship with a simple, refined aesthetic
sensitivity associated with traditional Japanese culture.
The result is a different notion of luxury
and beauty. The car itself is important, but
so is the sense of harmony that the vehicle
evokes in its driver, and the sense of
satisfaction you feel with the INFINITI —
from the way it looks and drives to the high
level of retailer service.
To ensure that you enjoy your INFINITI to
the fullest, we encourage you to read this
Owner’s Manual immediately. It explains
all of the features, controls and performance characteristics of your INFINITI; it
also provides important instructions and
safety information.
A separate Warranty Information Booklet
is included in your Owner’s literature
portfolio. Always carry it with you when
you take your vehicle to an INFINITI
retailer. The Warranty Information Booklet
contents provide complete information
about all warranties covering this vehicle,
the requirements to keep the warranties in
effect as well as the INFINITI Roadside
Assistance program.
Additionally, a separate Customer Care
and Lemon Law Information Booklet will
explain how to resolve any concerns you
may have with your vehicle, as well as
clarify your rights under your state’s
lemon law.
In addition to factory installed options,
your vehicle may also be equipped with
additional accessories installed by INFINITI
or by your INFINITI retailer prior to delivery.
It is important that you familiarize yourself
with all disclosures, warnings, cautions
and instructions concerning proper use of
such accessories prior to operating the
vehicle and/or accessory. It is recommended you see an INFINITI retailer for
details concerning the particular accessories with which your vehicle is equipped.
READ FIRST — THEN DRIVE SAFELY
Before driving your vehicle, read your
Owner’s Manual carefully. This will ensure
familiarity with controls and maintenance
requirements, assisting you in the safe
operation of your vehicle.
CV37D1-AC330383-C773-4EB3-A52F-61102B1D37CD
WARNING
IMPORTANT SAFETY INFORMATION REMINDERS!
Follow these important driving rules to help
ensure a safe and comfortable trip for you
and your passengers!
. NEVER drive under the influence of
alcohol or drugs.
. ALWAYS observe posted speed limits
and never drive too fast for conditions.
. ALWAYS give your full attention to
driving and avoid using vehicle features
or taking other actions that could
distract you.
. ALWAYS use your seat belts and appro-
priate child restraint systems. Pre-teen
children should be seated in the rear
seat.
. ALWAYS provide information about the
proper use of vehicle safety features to
all occupants of the vehicle.
. ALWAYS review this Owner’s Manual for
important safety information.
(4,1)
MODIFICATION OF YOUR VEHICLE
This vehicle should not be modified.
Modification could affect its performance,
safety or durability, and may even violate
governmental regulations. In addition,
damage or performance problems resulting from modification will not be covered
under the INFINITI warranties.
WARNING
Installing an aftermarket On-Board Diagnostic (OBD) plug-in device that uses the port
during normal driving, for example remote
insurance company monitoring, remote vehicle diagnostics, telematics or engine
reprogramming, may cause interference or
damage to vehicle systems. We do not
recommend or endorse the use of any
aftermarket OBD plug-in devices, unless
specifically approved by INFINITI. The vehicle warranty may not cover damage caused
by any aftermarket plug-in device.
WHEN READING THE MANUAL
This manual includes information for all
features and equipment available on this
model. Features and equipment in your
vehicle may vary depending on model, trim
level, options selected, order, date of
production, region or availability. Therefore, you may find information about
features or equipment that are not included or installed on your vehicle.
All information, specifications and illustrations in this manual are those in effect at
the time of printing. INFINITI reserves the
right to change specifications, performance, design or component suppliers
without notice and without obligation.
From time to time, INFINITI may update or
revise this manual to provide owners with
the most accurate information currently
available. Please carefully read and retain
with this manual all revision updates sent
to you by INFINITI to ensure you have
access to accurate and up-to-date information regarding your vehicle. Current versions of vehicle Owner’s Manuals and any
updates can also be found in the owner
section of the INFINITI website at https://
owners.infinitiusa.com/owners/navigation/manualsandGuides. If you have ques-
CV37D1-F1CA4D19-16D5-4A3C-AF71-1A2BB3AD052B
tions concerning any information in your
Owner’s Manual, contact INFINITI Consumer Affairs. See the INFINITI CUSTOMER
CARE PROGRAM page in this Owner’s
Manual for contact information.
IMPORTANT INFORMATION ABOUT
THIS MANUAL
You will see various symbols in this
manual. They are used in the following
ways:
CV37D1-3956A13C-AC00-461F-A84F-941327A05472
WARNING
This is used to indicate the presence of a
hazard that could cause death or serious
personal injury. To avoid or reduce the risk,
the procedures must be followed precisely.
CAUTION
This is used to indicate the presence of a
hazard that could cause minor or moderate
personal injury or damage to your vehicle. To
avoid or reduce the risk, the procedures
must be followed carefully.
(5,1)
SIC0697
If you see the symbol above, it means “Donot do this” or “Do not let this happen”.
NOS1274
If you see a symbol similar to those above
in an illustration, it means the arrow points
to the front of the vehicle.
NOS1275
Arrows in an illustration that are similar to
those above indicate movement or action.
NOS1276
Arrows in an illustration that are similar to
those above call attention to an item in the
illustration.
CALIFORNIA PROPOSITION 65
WARNING
CV37D1-22D8B75D-68F8-4799-AD77-37863EA09A12
WARNING
Engine Exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of
California to cause cancer and birth defects
or other reproductive harm. In addition,
certain fluids contained in vehicles and
certain products of component wear contain
or emit chemicals known to the State of
California to cause cancer and birth defects
or other reproductive harm.
CALIFORNIA PERCHLORATE ADVISORY
Some vehicle parts, such as lithium
batteries, may contain perchlorate material. The following advisory is provided:
“Perchlorate Material - special handling
may apply, See www.dtsc.ca.gov/
hazardouswaste/perchlorate.”
Manual may be reproduced or stored in a
retrieval system, or transmitted in any
form, or by any means, electronic, mechanical, photocopying, recording or otherwise,
without the prior written permission of
Nissan Motor Co., Ltd.
CV37D1-E6CD19EB-0ED1-45BF-BAC9-C1A7DD80922F
INFINITI-13P
(6,1)
INFINITI CUSTOMER CARE PROGRAM
CV37D1-7B10D04C-1C52-4B76-882C-7B9F38514835
INFINITI CARES ...
Both INFINITI and your INFINITI retailer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your
INFINITI retailer are our primary concerns. Your INFINITI retailer is always available to assist you with all your automobile sales and service
needs.
However, if there is something that your
INFINITI retailer cannot assist you with or
you would like to provide INFINITI directly
with comments or questions, please contact our (INFINITI’s) Consumer Affairs Department using our toll-free number:
For U.S. customers
1-800-662-6200
For Canadian customers
1-800-361-4792
The Consumer Affairs Department will ask
for the following information:
. Your name, address, and telephone
number
. Vehicle identification number (on dash
panel)
. Date of purchase
. Current odometer reading
You can write to INFINITI with the information on the left at:
For U.S. customers
INFINITI Division
Nissan North America, Inc.
Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003
or via e-mail at:
nnaconsumeraffairs@nissan-usa.
com
For Canadian customers
INFINITI Division
Nissan Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario L4W 4Z5
or via e-mail at:
information.centre@nissancanada.
com
If you prefer, visit us at:
www.infinitiUSA.com (for U.S. customer) or
www.infiniti.ca (for Canadian customers)
We appreciate your interest in INFINITI and
thank you for buying a quality INFINITI
vehicle.
. Your INFINITI retailer’s name
. Your comments or questions
OR
(1,1)
Table of
Illustrated table of contents
0
Contents
Safety — Seats, seat belts and supplemental restraint system
Instruments and controls
Pre-driving checks and adjustments
Monitor, climate, audio, phone and voice recognition systems
Starting and driving
In case of emergency
Appearance and care
Do-it-yourself
Maintenance and schedules
Technical and consumer information
1
2
3
4
5
6
7
8
9
10
Index
11
(2,1)
(7,1)
0 Illustrated table of contents
Seats, seat belts and Supplemental Restraint
System (SRS) ......................................................... 0-2
Exterior front ......................................................... 0-3