Indesit WIDXL 102 User Manual

0 (0)

Instructions for use

GB

 

AR

 

 

 

 

 

English,1

,15

WIDXL 102

WASHER-DRYER

Contents

GB

Installation, 2-3-4-5

Unpacking and levelling Electric and water connections The first wash cycle

Technical details

Washer-dryer description, 6-7

Control pane

Leds

Starting and Programmes, 8

Briefly: how to start a programme

Programme table

Personalisations, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser

Bleach cycle

Preparing your laundry

Special items

Precautions and advice, 11

General safety Disposal

Saving energy and respecting the environment

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning your appliance

Cleaning the detergent dispenser

Caring for your appliance door and drum

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Service, 14

Before calling for Assistance

1

Indesit WIDXL 102 User Manual

Installation

Keep this instruction manual in a safe place for GB future reference. Should the appliance be sold,

transferred or moved, make sure the instruction manual accompanies the washer-dryer to inform the new owner as to its operation and features.

Read these instructions carefully: they contain vital information on installation, use and safety.

Unpacking and levelling

Unpacking

1.Unpack the washer-dryer.

2.Check whether the washer-dryer has been damaged during transport. If this is the case, do not install it and contact your retailer.

3. Remove the four protective screws and

the rubber bush with the

respective spacer, situated on the rear of

the appliance (see also

the installation leaflet).

NB:The plastic spacers

may fall down inside the machine once the bolt

has been removed, and will not interfere with the operation of the machine.

4.Seal the gaps using the plastic plugs provided.

5.Keep all the parts: you will need them again if the washing machine needs to be moved to another location.

Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly.

1. Install the washer-dryer on a flat sturdy floor, without resting it up against walls, furniture cabinets or other.

2. If the floor is not perfectly level, compensate for any unevenness by tightening or

loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2°.

Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washer-dryer.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded

A

mouth (see figure).

 

 

Before making the

 

connection, allow the

 

water to run freely until

 

it is perfectly clear.

 

2. Connect the other end

 

of the water inlet hose to

 

the washer-dryer,

 

screwing it onto the

 

appliance's cold water

 

inlet, situated on the top

 

right-hand side on the

 

rear of the appliance

 

(see figure).

3. Make sure there are no kinks or bends in the hose.

The water pressure at the tap must be within the values indicated in the Technical details table

(on the next page).

If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman.

Ensure that the supply taps are allowing water through. Old taps may seize in the closed position and thus prevent water reaching the machine.

2

Connecting the drain hose

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;

Where it connects to the waste water pipe cut end off spigot or remove the blanking cap

The drain hose may be connected to an under-sink trap. Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot.

If it is place over the edge of a basin or sink be sure the free end of the hose should not be underwater.

We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a standpipe, that the end does not go down more than 15cms (6 inches). If the hose is pushed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make sure that:

the socket is earthed and in compliance with the applicable law;

the socket is able to sustain the appliance's maximum power load indicated in the Technical details table (see page 5);

• the supply voltage is included within the values

indicated on the Technical details table

GB

 

(see page 5);

 

the socket is compatible with the washer-dryer's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and you should wish to re-route the mains cable through partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewearable plug bearing the BSI mark of approval. or:

the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug: Important: the wires in the mains lead are coloured in accordance with the following code:

Green & Yellow Earth

Blue Neutral Brown Live

3

As the colours of the wires in the lead may not

GB

correspond with the coloured markings identifyng

 

 

the terminals in your plug, proceed as follows:

 

Connect Green & Yellow wire to terminal marked E

 

or

or coloured Green or Green & Yellow.

 

Connect Brown wire to terminal marked L or

 

coloured Red.

 

 

Connect Blue wire to terminal marked N or coloured

 

Black.

 

 

If a 13 amp plug (BS 1363) is used it must be fitted

 

with a

 

 

 

13 amp fuse, either in the plug or adaptor or at the

 

distribution board.

 

 

If you are in any doubt the electrical supply to your

 

machine, consult a qualified electrician before use.

 

How to connect an alternative plug:

 

The wires in this mains lead are coloured in

 

accordance with the following code:

 

BLUE

 

NEUTRAL (N)

 

BROWN

LIVE (L)

 

GREEN & YELLOW

EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.

GREEN &

YELLOW

13 ampere fuse

BROWN

BLUE

CROSS-BAR

 

CORD GRIP

Warning! The company denies all liability if and when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 90°C programme without a pre-wash cycle.

The washing machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms.

When the washing machine is installed, the mains socket must be within easy reach.

Do not use extensions or multiple sockets.

The power supply cable must never be bent or dangerously compressed.

The power supply cable must only be replaced by an authorised serviceman.

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Technical details

 

 

 

GB

 

 

 

 

 

 

 

 

 

 

 

 

Model

WIDXL 102

 

 

 

 

 

 

 

 

 

 

 

59.5 cm wide

 

 

Dimensions

85 cm high

 

 

 

 

 

53.5 cm deep

 

 

 

 

 

 

 

 

Capacity

from 1 to 6 kg for the wash programme;

 

 

from 1 to 4 kg for the drying programme

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Electric

please refer to the technical data plate

 

 

connections

fixed to the machine

 

 

 

 

 

 

 

 

Water

maximum pressure 1 MPa (10 bar)

 

 

minimum pressure 0.05 MPa (0.5 bar)

 

 

 

 

connections

 

 

drum capacity 52 litres

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spin speed

up to 1000 rpm

 

 

 

 

 

 

 

 

 

 

 

Wash: programme 2; temperature 60°C;

 

 

Control

run with a load of 6 kg.

 

 

Drying: first drying cycle performed with

 

 

 

 

programmes

 

 

a 2 kg load and the DRYING knob on

 

 

 

 

according to

 

 

the

setting;

 

 

 

 

EN 50229

 

 

Second drying cycle performed with a 4

 

 

 

 

directive

 

 

kg load and the DRYING knob on the

 

 

 

 

 

 

 

 

 

 

 

 

setting.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This appliance is compliant with the

 

 

 

 

 

following European Community

 

 

 

 

 

Directives:

 

 

 

 

 

- 89/336/CEE of 03/05/89

 

 

 

 

 

(Electromagnetic Compatibility) and

 

 

 

 

 

subsequent amendments

 

 

 

 

 

- 2002/96/CE

 

 

 

 

 

- 2006/95/CE (Low Voltage)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Washer-dryer description

 

 

 

 

 

 

 

 

 

 

 

 

Control panel

 

 

FUNCTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GB

 

 

 

 

Buttons

 

 

 

 

 

Leds

 

ON-OFF/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DOOR

 

ON-OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCK

 

Button

 

 

 

 

 

 

Led

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PROGRAMME

 

 

Detergent dispenser

 

Knob

 

 

START/RESET

 

Button

DRYING

TEMPERATURE

Knob

Knob

Detergent dispenser: to add detergent and fabric softener (see page 10).

LEDS: to find out the wash cycle progress.

DRYING knob: to set the desired drying cycle

(see page 9).

FUNCTION buttons: to select the functions available. The button corresponding to the function selected will remain on.

TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 9).

START/RESET button: to start the programmes or cancel any incorrect settings.

ON-OFF/DOOR LOCK Led: to find out whether the Washer-dryer is on and if the appliance door can be opened (see page 7).

ON/OFF button: to turn the Washer-dryer on and off.

PROGRAMME knob: to select the wash programmes. The knob stays still during the cycle.

6

Leds

GB

The LEDS provide important information. This is what they can tell you:

Cycle progress:

During the wash cycle, the LEDs gradually illuminate on to indicate the cycle progress:

Prewash / Wash

Rinse

Spin cycle

Drying

Note:

-during draining, the LED corresponding to the Spin cycle phase will be turned on.

-when the drying cycle is complete, the indicator light

relative to phase will flash, to indicate that the DRYING knob needs to be set back to the 0 setting.

Function buttons

The FUNCTION BUTTONS also act like LEDS. When a function is selected, the corresponding button is illuminated.

If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled.

If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled.

ON-OFF/DOOR LOCK led:

If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages, wait for the LED to flash before you open the appliance door.

The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED indicates there is an abnormality. Call for Technical Assistance (see page 13).

7

Starting and Programmes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Briefly: starting a programme

 

 

 

7. Start the programme by pressing the START/RESET

 

 

 

 

GB

 

1. Switch the Washer-dryer on by pressing button

.

 

 

button for one second. Once the programme has

 

 

 

been accepted all of the option and status LED's

 

 

All the LEDS will light up for a few seconds and

 

 

 

 

will illuminate momentarily, the Door Lock LED

 

 

the ON-OFF/DOOR LOCK Led will begin to flash.

 

 

 

 

will be lit and the relevant wash cycle progress

 

 

2. Load your laundry into the washing machine and

 

 

 

 

LED will also be lit.

 

 

 

 

shut the appliance door.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To cancel it, keep the START/RESET button pressed

 

 

3. Set the PROGRAMME knob to the programme

 

 

 

 

for at least 2 seconds.

 

 

 

 

required.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8. When the programme is finished, the ON-OFF/

 

 

4. Set the wash temperature (see page 9).

 

 

 

 

 

 

 

DOOR LOCK Led will flash to indicate that the

 

 

5. Set the drying cycle if necessary (see page 9).

 

 

 

 

appliance door can be opened. Take out your

 

 

6. Add the detergent and any fabric softener (see page 10).

 

 

 

 

laundry and leave the appliance door ajar to allow

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the drum to dry thoroughly. Turn the Washer-dryer

 

 

Programme table

 

 

 

 

 

 

 

off by pressing button

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D etergent

 

 

Stain

C ycle

M ax .

 

 

 

 

Type of fab ric and

 

 

D rying

 

 

Fabric

rem oval

Spin

 

 

 

 

Prog.

Tem p .

 

 

 

 

length

D escrip tion of wash cycle

 

 

d egree of soil

 

 

C ycle

 

p re-

w as h

 

softener

op tion/

(m inutes)

Speed s

 

 

 

 

 

 

 

 

 

 

 

b leach

(r.p .m .)

 

 

 

 

 

 

 

 

 

w as h

 

 

 

 

 

 

 

 

 

 

S tandard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Extremely soiled w hites

1

90°C

 

 

 

155

M ax.

Pre-wash, wash cycle, rinse cycles,

 

 

(sheets, tablecloths, etc.)

 

 

 

intermediate and final spin cycles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Extremely soiled w hites

2

90°C

 

 

 

D elicate/

150

M ax.

Wash cycle, rinse cycles,

 

 

(sheets, tablecloths, etc.)

 

 

 

Tradition al

intermediate and final spin cycles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heavily soiled whites and fast

2

60°C

 

 

 

D elicate/

140

M ax.

Wash cycle, rinse cycles,

 

 

colours

 

 

 

Tradition al

intermediate and final spin cycles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heavily soiled whites and

2

4 0°C

 

 

 

D elicate/

125

M ax.

Wash cycle, rinse cycles,

 

 

delicate colours

 

 

 

Tradition al

intermediate and final spin cycles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sligh tly soiled w h ites and

 

 

 

 

 

 

 

 

D elicate/

 

 

Wash cycle, rinse cycles,

 

 

delicate colours (sh irts,

3

4 0°C

 

 

 

85

M ax.

 

 

 

 

 

Tradition al

intermediate and final spin cycles

 

 

jum pers, etc.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heavily soiled fast colours

4

5 0°C

 

 

 

D elicate

72

800

W ash cycle, rinse cycles, anti-

 

 

(baby linen, etc.)

 

 

 

crease or delicate spin cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heavily soiled fast colours

4

4 0°C

 

 

 

D elicate

70

800

W ash cycle, rinse cycles, anti-

 

 

(baby linen, etc.)

 

 

 

crease or delicate spin cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

W ool

5

4 0°C

 

 

 

 

 

50

600

W ash cycle, rin s e cycles ,

 

 

 

 

 

 

 

delicate spin cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Very delicate fabrics

6

30°C

 

 

 

 

 

45

no

W ash cycle, rin s e cycles , an ti-

 

 

(cu rtain s, s ilk, vis cose, etc.)

 

 

 

 

 

crease or drain in g cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D ryin g cotton

7

 

 

 

 

 

 

 

 

M ax.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D ryin g delicates

8

 

 

 

 

 

 

 

 

no

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tim e 4 you

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heavily soiled whites and fast

9

60°C

 

 

 

 

 

60

M ax.

Wash cycle, rinse cycles,

 

 

colours

 

 

 

 

 

intermediate and final spin cycles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Delicate colours (all types of

10

40°C

 

 

 

 

 

40

800

W ash cycle, rinse cycles,

 

 

slightly soiled garments)

 

 

 

 

 

delicate spin cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Delicate colours (all types of

11

30°C

 

 

 

 

30

800

W ash cycle, rin s e cycles and

 

 

slightly soiled garments)

 

 

 

 

delicate spin cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cold w ash (w ithout detergents),

 

 

Sports shoes (MAX. 2 pairs)

12

30°C

 

 

 

 

 

5 0

800

w ash cycle, rinse cycles, and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

delicate spin cycle

 

 

Fabrics for sportsw ear

13

30°C

 

 

 

 

 

60

600

Wash cycle, rinse cycles,

 

 

(Tracksuits, shorts, etc.)

 

 

 

 

 

intermediate and final spin cycles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PAR TIAL PR OGR AM M ES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R in s e

 

 

 

 

 

 

D elicate/

 

800

R in s e cycles an d spin cycle

 

 

 

 

 

 

 

 

Tradition al

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spin cycle

 

 

 

 

 

 

 

 

 

800

Draining and spin cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D rain

 

 

 

 

 

 

 

 

 

 

no

D rain

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

-For programme 9, we advise against exceeding a wash load of 3.5 kg. -For programme 13 we advise against exceeding a wash load of 2 kg.

-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.

Special programme

Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

8

Personalisations

C Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).

 

 

 

GB

 

 

 

 

 

 

 

 

 

The temperature can be lowered, or even set to a cold wash (

).

 

 

The data contained in the

 

 

 

 

 

 

 

Set the drying cycle

Table of drying times

 

table are purely indicative.

 

 

 

 

 

 

 

 

 

Fabric

Load type

Max.

 

 

 

 

Turn the DRYING knob to set the desired drying type.

 

 

 

 

type

 

load

 

 

 

 

Two options are available:

 

 

(kg)

Cup-

Hanger

Iron

 

 

 

 

board

 

 

 

 

 

 

 

 

 

 

 

 

A - Based on time: From 40 minutes to 150.

 

 

 

 

 

 

 

Cotton,

Clothing of different sizes

 

 

 

 

 

B - Based on the damp level of the dry clothes:

4

130

120

110

 

Linen

 

 

 

 

 

 

 

 

 

 

 

Iron

: slightly damp clothes, easy to iron.

 

 

 

 

 

 

 

Hanger : dry clothes to put away.

Cotton

Terry towels

4

130

120

110

 

Cupboard

: very dry clothes, recommended for towelling

 

 

 

 

 

 

 

Terital,

Sheets, Shirts

2,5

90

80

70

 

and bathrobes.

 

Cotton

 

 

A cooling stage is foreseen at the end of the drying cycle.

 

 

 

 

 

 

 

Acrylics

Pyjamas, socks, etc.

1

65

60

60

 

 

 

 

 

If your laundry load to wash and dry is exceptionally in excess

 

 

 

 

 

 

 

Nylon

Slips, tights, stockings, etc.

1

65

60

60

 

of the maximum load foreseen (see table opposite), perform

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the drum. Now follow the instructions provided for a dry only cycle. Repeat this procedure for the remainder of the load.

Dry only

Turn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the desired drying type using the DRYING knob.

Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of dryness (Cupboard , Hanger , Iron ).

- For cotton loads of less than 1 Kg, use the drying programme designed for delicate fabrics.

Functions

To enable a function:

1.press the button corresponding to the desired function, according to the table below;

2.the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.

Function

Effect

Comments

 

Enabled with

 

programmes:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bleaching cycle

Please remember to pour the bleach into extra compartment 4

2, 3, 4,

 

 

 

designed to

 

 

 

(see page 10).

 

Stain

remove the

 

Rinse cycle.

This function is incompatible with the EASY IRON function.

removal

toughest stains.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When this function is set, programmes 4, 6 will end with the

 

 

 

 

This option

laundry left to soak (Anti-crease) and the Rinse cycle phase

 

 

 

 

LED

will flash.

 

 

 

 

 

reduces the

 

 

 

 

 

- to conclude the cycle, press the START/RESET button;

3, 4, 6,

 

 

 

amount of

 

 

 

- to run the draining cycle alone, set the knob to the relative

 

 

 

creasing on

9, 10,

 

 

 

symbol

and press the START/RESET button.

 

 

 

fabrics, making

Rinse cycle.

 

 

 

This function is incompatible with the STAIN REMOVAL function.

 

 

 

them easier to

 

 

 

 

 

 

 

 

 

 

 

iron.

If you also want to run the drying cycle, this button is enabled

 

 

 

 

 

 

Easy iron

 

only if combined with level

(Iron).

 

 

 

 

 

 

 

 

 

 

 

 

Increases the

Recommended when the appliance has a full load or with large

1, 2, 3, 4, 9,

 

 

 

efficiency of the

10, 12, 13,

 

 

 

quantities of detergent.

 

Extra Rinse

rinse.

 

Rinse cycle.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All

 

 

 

Reduces the

 

 

 

programmes

 

 

 

spin speed.

 

 

 

except for 6, 7,

1000-500

 

 

 

 

8 and draining.

 

 

 

 

 

 

 

 

The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the final spin speed if an unbalanced load is detected.

9

Loading...
+ 19 hidden pages