IDL 700 IDL 705
Dishwasher
Installation and use
Safety Is a Good Habit to Get Into
NOTICE
Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance.
This appliance complies with the following EEC directives:
-73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;
-89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications.
-97/17/EEC Labelling
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional.
3.The dishwasher must only be used by adults for the washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
-Never touch the dishwasher when barefoot or with wet hands or feet;
-We discourage the use of extension cords and multiple sockets;
-During installation, the power supply cord must not be excessively or dangerously bent or flattened;
-If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the power supply.
5.Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open. 6.This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements. 7.Do not touch the heating element during or after a wash cycle.
8.Do not lean or sit on the door when it is open, as this could overturn the dishwasher.
9.If the appliance malfunctions, turn off water supply to the appliance and disconnect the plug from the wall socket. Then, consult the section entitled, "Troubleshooting." If you cannot resolve the problem, contact a service centre.
10.Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock.
To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:
λcall only the Service Centers authorized by the manufacturer
λalways use original Spare Parts
Close-up View (control panel)
G |
H |
L E |
F |
R |
D |
|
A |
||||||
|
|
|
|
|
||
|
|
|
Intensive Time 4 you |
Eco Rapid '25 |
|
|
|
|
|
|
25 |
|
Soak |
Crystal Care |
Just You |
5 |
6 |
7 |
B
I C
ON - OFF Button
Cycle phase and delayed start indicator lights
ON - OFF Light
Delayed Start Select Button
Handle For Opening Door
"1/2 Load" Button
Knob For Selecting Cycles
"1/2 Load" Indicator Light
Low Salt Indicator Light
Start/Reset Button
Low Rinse Aid Indicator Light
1 |
GB |
Close-up View (Interior)
E
G 
F
H
J
K
I
L
Upper Rack |
Bottom Sprayer Arm |
Top Sprayer Arm |
Salt Container Cap |
Rack Height Adjustor |
Washing Filter |
Lower Rack |
Detergent and Rinse Aid Dispenser |
7HFKQLFDO FKDUDFWHULVWLFV
Width |
cm. 60 |
|
Depth |
cm. |
60 |
|
|
|
Height |
cm. |
85 |
Capacity |
12 standard place settings |
|
|
|
|
Mains water pressure |
30 KPa÷ 1MPa (0,3 ÷10 bar) |
|
|
|
|
Power voltage |
See data plate |
|
|
|
|
Total absorber power |
See data plate |
|
|
|
|
Fuse |
See data plate |
|
|
|
|
GB |
2 |
Salt ......
Salt
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows:
1.Remove the lower rack and then unscrew and remove the cap from the salt container;
2.If you are filling the container for the first time, fill it with water;
3.Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container.
4.Carefully screw the cap back on.
The salt container should be filled up when the low salt indicator light "E" flashes.
Once you have loaded the salt for the first time, it is normal that the low salt indicator light stays on or flashes for about 5 consecutive cycles.
Warning: To prevent rust from forming, we advise you to load the salt before starting a wash cycle.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of salt consumed based
on the harness of the water
used. This is intended to optimize and customize the
level of salt consumption so that it remains at a minimum.
Your Local Water Board can supply the degree of hardness
of the water in your area.
To adjust salt consumption, proceed as follows:
1)Unscrew the cap from the salt container.
2)There is a ring on the container with an arrow on it (see figure to the side), if necessary, rotate the ring in the anticlockwise direction from the "_" setting towards the "+" sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accordance with the following schema:
Water Hardness |
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
Salt |
Autono- |
|
|
|
|
|
consu- |
||
Clarke |
|
|
Selector |
my |
||
°fH |
mmol/l |
mption |
||||
degrees |
position |
(cycles\2- |
||||
|
|
(grams/- |
||||
|
|
|
|
kg) |
||
|
|
|
|
cycle) |
||
|
|
|
|
|
||
|
|
|
|
|
|
|
0 - 14 |
0 - 17 |
0 -1,7 |
/ |
0 |
/ |
|
|
|
|
|
|
|
|
14 - 36 |
18 - 44 |
1,8 - 4,4 |
"-" |
20 |
60 |
|
|
|
|
|
|
|
|
36 - 71 |
45 - 89 |
4,5 - 8,9 |
MED |
40 |
40 |
|
|
|
|
|
|
|
|
>71 |
>89 |
> 8,9 |
"+" |
60 |
25 |
|
|
|
|
|
|
|
|
3 |
GB |
Loading...