EDPE G45 A1 Eco
EN
1
Contents
Installation, 2
Where to install the tumble dryer
Ventilation
Electrical connections
Levelling the tumble dryer
Preliminary information
Warnings, 4
General safety
Saving energy and respecting the environment
Care and maintenance, 6
Disconnecting the power supply
Cleaning the filter after each cycle
Checking the drum after each cycle
Emptying the water container after each cycle
Cleaning the Heat Pump Filter
Cleaning the tumble dryer
Description of the tumble dryer, 8
Features
Control panel
How to carry out a drying cycle, 10
Starting and selecting a programme
Programmes and options, 11
Programme chart
Special programmes
Options
Opening the door
Laundry, 14
Sorting laundry
Care labels
Drying times
Troubleshooting, 15
Assistance and garantee, 16
Spare parts
Assistance and guarantee
Information on recycling and disposal
Instruction manual
! This symbol reminds you to read this
instruction manual.
! Keep this manual at hand for immediate reference whenever
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or tran-
sferring the appliance, so they may familiarise with the warnings
and suggestions herein contained.
! Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
www.indesit.com
English,1
EN
TUMBLE DRYER
FR
Deutsch, 33
Français,17
DE
Nederlands, 49
NL
EDPE G45 A1
EDPE G45X A1
2
EN
Where to put your dryer
• Place your dryer at a
distance from gas ranges,
stoves, heaters, or cooktops
because flames can damage
the appliance. The dryer
should be installed in an
ambient room temperature
of between 20 to 23°C
for optimum performance.
But will function if the room is between 14 and
30°C. If you are going to install the appliance
under a work counter, be sure to leave a 10 mm
space between the top and any other objects
on or above the machine and a 15 mm space
between the sides and lateral furnishings or
walls. This is to ensure proper air circulation.
The appliance must be installed with the rear
surface placed against a wall.
Ventilation
• When the dryer is in use, there has to be adequate ventilation.
Make sure you put your dryer in an environment that is not damp
and has proper air circulation throughout. Airflow around the dryer is
essential to condense the water produced during the washing, the
dryer will not operate efficiently in an enclosed space or cupboard.
! If using the dryer in a small or cold room some
condensation will be experienced.
!
We do not recommend that the dryer is
installed in a cupboard but the dryer must never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
1
2
2
1
Less than 1m
Fig. A Fig. B
Water Drain
If the machine is positioned close to a drain it is possible to drain the
condensed water directly without using the waterbottle. In which
case it is no longer necessary to empty the water bottle at the end
of each cycle. If the Dryer is positioned above or close to a Washing
Machine the same drainage can be used. Just remove the tube
indicated in figure A and connect it to the drainage. If the drainage
is further away than the length of the tube it is possible to buy and
connect a tube of the same diameter and the necessary length in
order to reach the drain. To install the new tube just substitute the
existing one as indicated in figure B inserting it in the same place.
! The drain tube has to be below 1 m from the bottom of
the Dryer.
! Once the Dryer has been installed please assure that
the drain tube is not bent or kinked.
Electrical connections
Before plugging the appliance into the socket,
check the following:
• Make sure your hands are dry.
• The socket must have an earth connection.
• The socket must be able to withstand the
machine’s maximum power output as indi-
cated on the rating plate (see Description
of the tumble dryer)
• The power supply voltage must fall within
the values indicated on the data plate (see
Description of the tumble dryer).
• The socket must be compatible with the
dryer’s plug. Should this not be the case,
replace the plug or the socket.
! DO NOT USE EXTENSION CORDS.
! The dryer must not be installed outdoors,
even if the space is sheltered. It can be very
dangerous if exposed to rain or storms.
! Once installed, the dryer’s electrical wire and
plug must be within reach.
! The power cord must not be bent or
squashed.
! If the plug being replaced is a non-
rewirable type, then the cut-off plug must
be disposed of safely. DO NOT leave it
where it can be inserted into a socket
and create a shock hazard.
! The power must be regularly che-
cked. If the supply cord is damaged, it
must be replaced by the manufacturer,
its service agent or similarly qualified
persons in order to avoid a hazard.
(see Assistance). New or longer elec-
tric cords are supplied by authorised
dealers at a supplementary cost.
! The manufacturer denies any
responsibility should any of these rules
not be followed.
! If in doubt about any of the above
consult a qualified electrician.
Levelling the tumble dryer
The dryer must be installed level for correct
operation.
When you have installed your dryer in its final
location check that it is level first side-to-side,
Installation
10 mm
15 mm
15 mm
EN
3
This household tumble drier is a Condenser
The weighted Annual Energy Consumption (AEc)* kWh 1) 306.0
This household tumble drier is a Automatic
Energy consumption full load; Edry - kWh 2) 2.64
Energy consumption partial load; Edry½ - kWh 2) 1.34
Power consumption: off-mode (Po) - Watts 0.14
Power consumption: left-on mode (Pl) - Watts 2.39
Prog. Time - weighted (Tt) full & partial load - minutes 3) 173
Full load (Tdry) - minutes 235
Partial load (Tdry½) - minutes 127
weighted (Ct) full & partial load 3) 71
full load (Cdry) 72
partial load (Cdry½) 71
Airborne acoustical noise emissions - dB(A) re 1 pW 69.0
Programme time in minute, for program “Synthetics” full load 90
Partial load for program “Synthetics” N/A
Average condensation efficiency - %
1) "Standard cotton” at full and partial load is the standard programme to which the
information in the label and the fiche relates. The standard cotton program is
suitable to dry at cupboard level (0%) cotton laundry and is the most efficient
programme in terms of energy consumption. Partial load is half the rated load.
2) based on 160 drying cycles of the standard cotton programme at full and partial
load, and the consumption of the low-power modes. Actual energy consumption
will depend on how the appliance is used.
3) Weighted average of 3 cycles at full load and 4 cycles at half load.
Regulation 9 32/201 2.
Energy consumption in kWh, for program “Synthetics” full load 0.92
Energy efficiency class on a scale from A+++ (low consumption)
to D (high consumption)
A+
Duration of the 'left-on mode' for power management system -
minutes
30
Condensation efficiency class on a scale from G (least efficient) to
A (most efficient)
C
P
roduct Data - Regulation 392/2012.
Brand
Indesit
Model
EDPE G45 A1 ECO (EU) - EDPE G45X A1 ECO (EU)
Rated capacity of cotton laundry for the "standard cotton
programme" at full load - kg
8.0
then front to back. If the dryer is not level,
adjust the two legs up or down until your
dryer is level.
Preliminary information
Once you’ve installed your dryer and before you use it, clean
the inside of the drum to remove any dust that could have
accumulated during transportation.
Warning ! Before you use your dryer ensure that its has
been in a upright position for at least 6 hours.
Maximum load sizes: maximum 8 kg
4
EN
Warnings
! This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
• Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where
the pile height would prevent air from
entering the dryer from the base.
• Check to see if the dryer is empty before
loading it.
•
The back of the dryer could become
very hot. Never touch it while in use.
• Do not use liquid fabric softeners in the
dryer; add it to the final rinse of your wash.
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the Water Container after each use
(see Maintenance).
• Clean the Heat Pump filter unit at regular
intervals (see Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your tumble
dryer, the following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed and
been through the spin cycle. It is a fire hazard
to dry items that HAVE NOT been washed
with water.
• Do not dry garments that have been treated
with chemical products.
• ●Do not tumble dry items that have been
spotted or soaked with vegetable or cooking
oils, this constitutes a fire hazard. Oil-affected
items can ignite spontaneously,especially
when exposed to heat sources such as
a tumble dryer. The items become warm,
causing an oxidisation reaction with the
oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent heat
from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing
vegetable or cooking oil or those that have
been contaminated withhair care products
be placed in a tumble dryer they should first
be washed with extra detergent - this will
reduce, but not eliminate the hazard. They
should not be removed from the dryer and
piled or stacked while hot.
• ●Do not tumble dry items that have previously
been cleaned in or washed in, soaked in
or soiled with petrol/gasoline, dry cleaning
solvents or other flammable or explosive
substances. Highly flammable substances
commonly used in domestic environments
including cooking oil, acetone, denatured
alcohol, kerosene, spot removers, turpentine,
EN
5
waxes and wax removers. Ensure these
items have been washed in hot water with
an extra amount of detergent before being
dried in the tumble dryer.
• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by
the manufacturer of the fabric softener
product.
• ●Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
• ●Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• ●Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• ●Remove all objects from pockets such as
lighters and matches.
! WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select
a high spin cycle). Doing this will save time and energy
during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
6
EN
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once
drying is completed, by
rinsing it under running
water or cleaning it with a
vacuum cleaner. Should
the filter become clog-
ged, the flow of air inside
the dryer will be seriously
hampered: drying times becomes longer and
more energy is consumed. Moreover, the dryer
may become damaged.
The filter is located in
front of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic
handle upwards (see
Picture).
2. Clean the fluff off the
filter and replace it correctly. Ensure that the
filter is pushed fully home.
! Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items (handker-
chiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the
stainless steel drum surface: it may be caused by a combina-
tion of water and/or cleaning agents such as wash-softeners.
This coloured film does not affect the dryer’s performance.
Emptying the water container after each
cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water contai-
ner and empty it before starting
a new drying cycle.
-Failure to empty the water container may cause the
following:
- The dryer stops heating (thus the load may still be
damp at the end of the drying cycle).
- The “Empty water container” LED activates to show
that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will not
collect Water until the system is primed, this will take
1 or 2 drying cycles. Once primed it will collect Water
during every cycle.
Cleaning the Heat Pump Filter Unit
• Periodically (every 5 drying cycles) remove
Heat pump filter unit and clean any build up
of fluff from the surface of the filter by rinsing
it under running water or with your vacuum
cleaner.
We however recommend that you clean this
filter after every drying cycle to optimize the
dryers performance.
To remove Heat pump
filter unit:
1. Unplug the dryer and
open the door.
2. Remove the filter unit
by rotating the 4 clips
to the vertical position
then pulling the filter
unit towards you.
3. Separate the two
parts of the filter unit and
clean the surface of the
filter.
! Warning: The front of
the heat pump is made
from thin metal plates.
Take care that you do
not damage these or cut
yourself when cleaning,
removing or replacing
the filter unit.
Care and maintenance
2
EN
7
4.Whenever you clean
the Heat pump filter
unit always clean any
build up of fluff from
the surface of the metal
plates. Carefully clean
this fluff off with a damp
cloth,sponge or vacuum
cleaner. Never use your
Fingers.
5. Assemble the two parts of the filter clean
the surface of the seals and replace with the
4 clips into the horizontal position, sure that
the catches have been secured.
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be clea-
ned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechani-
cal parts work safely (see Assistance).
2
Water container
Heat pump
filter unit
Condenser cover
Catches
Filter
Handle
Air intake
Quick Tips
!Remember to clean your filter and Heat
Pump filter unit after each load.
! Remember to empty your water contain-
er after each load.
! Doing this will keep your machine work-
ing at its BEST!
8
EN
On/Off
button
Start/Pause button
and indicator light
Programme
selection knob
Press
the door
Heat Pump
Filter Unit
(cover open)
Water container
Rating plate
Heat Pump Filter
Unit cover handle
(Pull here to open)
Filter
Air
intake
grille
Description of
the tumble dryer
Opening the door
Control panel
Features
Options
buttons and
indicator lights
Display
Delay start
button
Timed Drying
button
Empty water
container indicator light
Clean filter
indicator light
Clean
Heat
Pump Filter
indicator light
Cycle
phases
Timed
drying
icon
Delay
start icon
Model
& Serial
Numbers
Ajustable feet
(to level dryer)
EN
9
ON/OFF/Reset button
Pressing the button normally will cause the machine to switch on or off. If the button is pressed for 3 seconds while the dryer is in use,
the machine will switch off and the running cycle will reset.
Programme selection knob
Allows for setting the programme: turn until the indicator points towards the desired programme (see Starting and selecting a programme).
Options buttons
Allows selection of the options available for the selected programme. The respective indicator lights turn on when the option has been
selected (see Programmes and options).
START/PAUSE button and indicator light
When the green light flashes slowly, press the button to start the programme. When the cycle is under way, the indicator light re-
mains on. Press the button again to put the programme in the pause mode; the indicator light turns orange and starts flashing again.
Press the button again to resume the programme from the point it was interrupted (see Starting and selecting a programme).
Display
In section A, the selected “Timed drying” value is displayed; if the “Delay start” function was set, the time remaining to the start of the
selected programme will appear.
The duration of the selected programme is also displayed in this section.
In section B, the phase of the running programme is displayed:
Sun icon : Drying cycle
Fan icon : Cool tumble cycle
In section C, the maintenance indicator lights are displayed (Empty water container indicator light , Clean filter indicator light ,
Clean Heat pump filter unit indicator light ), see Indicator lights.
Indicator lights
The indicator lights provide important information. They indicate the following:
The “Empty water container” indicator light signals that the water container must be emptied.
If the water container fills during the course of the programme, the LED lights up. The dryer automatically starts a cold air cycle and
the START/PAUSE LED flashes orange. Press the START/PAUSE button to resume the cycle from the point it was interrupted.
In order to avoid this procedure, always empty the water container after using the tumble dryer (see Maintenance).
Before each programme, the “Clean filter” indicator light signals the fundamental importance of cleaning the filter before each load
(see Maintenance).
The “Clean Heat pump filter unit” indicator light indicates that you must clean the Heat pump filter every 5 cycles (however, we
recommend you clean it after each cycle).
C
B
A
10
EN
How to carry out a
drying cycle
Starting and selecting a programme
1. Plug the dryer into the power supply socket.
2. Select the programme according to the type of laundry (see Laundry).
3. Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted (see
Maintenance).
4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door.
5. Press the ON/OFF button to switch on the machine.
6. After consulting the programme chart and the indications for each type of fabric (see Laundry), turn the Programme selection
knob towards the programme corresponding to the type of laundry to be dried (see Programmes and options).
! Warning: If the position of the programme selection knob changes after pressing the START/PAUSE button, the selected program-
me will NOT be modified. To modify the programme, press the START/PAUSE button to put the programme in pause mode (the
indicator light flashes orange), then select a new programme and the relative options. Press the START/PAUSE button to start the
new programme.
7. Select the ”Timed Drying” function by pressing the timed drying button until the required time is dispayed (see Programmes and
options).
8. If necessary, set the time of the delayed start and any other options (see Programmes and options).
9. Press the ALARM button to sound a buzzer signalling the end of the programme.
10. Press the START/PAUSE button to start the drying cycle. The display will show the approximate time remaining.
Laundry can be checked while the drying programme runs and any garments already dry can be removed, while drying continues
for the remaining items. After closing the door, press the START/PAUSE button to resume machine operation.
11. The final COOL TUMBLE phase (i.e. the fabrics are cooled) activates during the last few minutes of the drying programme;
always allow this phase to terminate.
12. At the end of the drying cycle the display shows END.
The buzzer will beep 3 times to let you know that your programme is complete. (Note: If the SOUND option was selected the buzzer
beeps 3 times every 30 seconds for 5 minutes).
Open the door, remove the laundry then clean the filter and replace it. Empty the water container and put it back in its slot (see
Maintenance).
If the clothes are not removed at the end of the cycle the automatic Anti Craese action will, on those programmes with this feature,
continue to rotate the drum intermittently for up to 10 hours to minimise creasing. Opening the door or pressing the OFF button will
stop the Anti Crease action.
13. Disconnect the dryer from the power supply.
Automatic pre-post Anti Crease
This is an automatic function which provides an anti crease treatment both before and after the drying programme. By periodically
rotating the drum before the start of the drying cycle, when a delayed start is selected, the formation of creases is reduced. On
certain programmes the drum also rotates periodically at the end of the drying cycle on. This post crease care action continues until
either the door is opened or the OFF button is pressed.
Standby mode
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled
after about 30 minutes if no activity is detected. Press and hold the ON/OFF button until the dryer reactivates.
EN
11
Programme chart
Programmes and options
Special/Sport/Partial Programmes
Fast 45’
45
’
This is a quick timed programme, ideal for drying garments spun at high speed in the washing machine, for example shirts used in a
working week.
Easy Mix
This programme is ideal for drying cotton and synthetic fabrics together.
Less Creased
A cycle for synthetic and mixed textiles making lengthy ironing unnecessary.
Shake the pieces of clothing before introducing them into the dryer. Remove the pieces of clothing immediately at the end of the
programme and hang them
Standard Cotton: Dries your items to a dryness level that allows you to put your clothes away straight from the dryer.
Cotton Ready to Wear: Dries your items to the maximum possible dryness level. Even drier than Standard Cotton.
Jeans
●This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.
●Do not mix dark and light coloured items.
It can also be used on other garments made from the same material, such as jackets.
Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is the case, try turning
the jeans inside out and running the programme again for a short period.
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.
Programme
Max.
load
(kg)
Compatible options
Cycle
duration
Fast & Easy
The duration of the drying cycles can be checked on the display
3
.
1 Fast 45
1
Memo - Key Lock- Delay Timer.
2 Easy mix
3
Memo - Key Lock- Delay Timer.
3 Less Creased
3
Memo - Key Lock.
4 Cotton fast Iron
Max. Extra Care - Memo - Key Lock- Time Dry - Delay Timer.
5 Synthetic fast Iron
4 Memo - Key Lock- Time Dry - Delay Timer.
Essentials
6 Standard Cotton
2
Max. Extra Care - Energy Saver
1
- Memo - Key Lock- Time Dry - Delay Timer.
7 Cotton ready to wear
Max. Memo - Key Lock- Time Dry - Delay Timer.
8 Synthetics
4 Energy Saver
1
- Memo - Key Lock- Time Dry - Delay Timer.
9 Jeans
3
Memo - Key Lock- Delay Timer.
Special Care
10 Baby&Delicates
2 Memo - Key Lock- Time Dry - Delay Timer.
11 Wool
1 Memo - Key Lock.
12 Duvet
1,5 Memo - Key Lock- Delay Timer.
13 Gym kit
4 Memo - Key Lock- Delay Timer.
14 Special Shoes
1 pair Memo - Key Lock.
Post Dry
15
Crease Relax - Memo - Key Lock.
16
Freshen UP 2,5 Memo - Key Lock.
NOTES: 1 with this option the maximum load size is modifi ed. Refer to the option description. 2 Standard Cotton is the most effi cient program
in terms of energy consumption (EU 392/2012). 3 The duration of these programs will depend on the size of the load, types of textiles, the spin
speed used in your washer and any extra options selected.
12
EN
Baby&Delicates
A programme appropriately designed to dry clothing and linen of new-born babies (cotton and chenille) and delicate clothes. Do not
dry articles which have plastic covering.
Wool Programme
This programme is specific for items that withstand tumble drying and are labelled with the symbol. It is suitable for loads of up to
1 kg (about 3 jerseys). We recommend turning the garments inside out before drying them. Garments dried with this programme are
usually ready to be worn, although the edges of heavier garments may be slightly damp. Leave them to dry naturally, as an additio-
nal drying process may damage them.
Unlike other materials, the shrinking process in wool is irreversible, i.e. the garment does not resume its original dimension and sha-
pe. This programme is not suited for acrylic items.
Duvet
A cycle intended to dry down jackets, giving their natural softness back (2 jackets).
Gym Kit
A cycle designed to dry complete gym kits for all the family (shorts, top, t-shirts and towels).
Special Shoes Programme
This programme is specific for drying sports shoes. The shoes must have been previously washed and spun at a minimum spin
speed of 400 revolutions.
A specific shoe rack is provided and must be used, otherwise the dryer will be damaged if shoes are dried in the drum. Remove the
filter from its holder on the front part of the dryer and position the shoe rack.
Place shoelaces inside the shoes then load with the tips of the shoes facing downwards and the soles frontwards.
Drying times vary according to the shape and type of the shoe. If the shoes are not completely dry at the end of the programme,
restart the programme.
! Do not dry shoes that have gel or flashing lights inside them. Only dry shoes made of synthetic material or rope. Once the pro-
gramme ends, remove the shoe rack and replace the filter into its holder.
Crease Relax
A short 10-minute programme that relaxes the garment’s fibres in order to facilitate ironing and folding.
This programme is particularly recommended for cotton or mixed cotton fabrics.
For optimal results, do not overload the drum (the following values refer to the weight of dry garments):
Fabric: maximum load
Cotton and mixed cotton: 2.5 kg
Synthetic garments: 2 kg
Jeans: 2 kg
Empty the dryer as soon as the programme ends; hang, fold or iron garments then place them in the wardrobe. If this is not possi-
ble, repeat the programme.
As this is not a drying programme, it is not to be used for garments that are still wet.
The effect produced by the programme varies according to the characteristics of the each fabric: fabrics such as acrylic fibres or
Tencel
®
do not give the same results as traditional fibres (e.g. cotton).
Freshen Up
A short programme suitable for refreshing fibres and garments. It lasts about 20 minutes.
! As this is not a drying programme, it is not to be used for garments that are still wet.
● It can be used on any load size but is more effective on smaller loads.
Options
The options allow for customising the selected programme according to one’s own needs.
Timed drying
After selecting a programme, press the “Timed drying” button to enter a drying time. Every time this button is pressed, the duration of
the selected drying cycle appears on the display. When pressed the first time, the highest allowed value for the selected cycle appears
on the display. When pressed each of the following times, the set time is reduced until OFF appears.
The buzzer will activate if the timed drying option is not available.
EN
13
Delay Timer
The start of some programmes (see Programmes and options) may be delayed up to 24 hours. Before selecting a programme with
a delayed start make sure that the water bottle is empty and the filter is clean. The drum will rotate occasionally before the drying
programme starts to prevent the formation of creases.
Extra Care
This is a special option designed to gentle dry delicate clothes.
Press this button to select the low temperature setting; the light next to the button will switch on. Activating this option will increase
the duration of the cycles.
Energy Saver
An option designed to optimise the results when drying small loads (cotton loaded to a max. of 2 kgs. and synthetic
load to a max. of 1 kg.) thereby minimising consumption and drying times.
Memo
This option allows you to store your cycle selection along with any associated options and to easily use a previously stored cycle.
Delayed start options cannot be stored.
•Press and hold the button MEMO for 3 second to store a cycle. You can press this button when the desired cycle and associa-
ted options have been selected either before the cycle has started or during the drying cycle. When you press and hold the Memo
button the LED flashes as well as the time on the display and after 3 second a beep will confirm that the details have been stored.
•To recall the stored cycle simply turn on the dryer, press the memo button and then start the cycle. It is possible to change any of
the options in the normal way. Every 2 minutes the stored cycle number will appear on the display. If no cycle has been stored you
will hear a beep when the Memo button is pressed.
•A stored programme can be overwritten with a new programme just by repeating the steps outlined above.
Key Lock
Keep this button pressed for a few seconds after choosing the programme and the desired options. When the warning
light is on, the other buttons and the knob are deactivated. To deactivate the block keep the button pressed and the
warning light goes off. The ON/OFF button switches off the machine even if the function lock button is active.
Not all options are available on all programmes (see Programmes and options).
Opening the door
If the door is opened (or the START/PAUSE button is pressed) while a programme is running, the dryer stops and the following may
occur:
• The START/PAUSE button flashes orange.
• When a delayed start is running, the delay countdown continues. It is necessary to press the START/PAUSE button to resume
the “Delay start” programme. The “Delay start” indicator light flashes and the display visualises the time remaining to the start of the
selected programme.
• It is necessary to press the START/PAUSE button to resume the programme. The progress indicator lights signal the running pha-
se and the START/PAUSE indicator light stops flashing and turns green.
• During the post anti-crease phase, the programme ends. Pressing the START/PAUSE button reactivates a new programme from
the beginning.
• By turning the Programme selection knob, a new programme is selected and the START/PAUSE indicator light flashes green. This
procedure can be used to select the COOL drying programme to cool garments if they are judged to be dry enough.
Press the START/PAUSE button to start the new programme.
Heat Pump Protection System
The heat pump sytem has a compressor protection feature, that operates if you open the door or there is a power disruption or you
turn off the dryer. This system will prevent the heat pump compressor from starting for 5 minutes after the door is closed and the
programme started.
Note: If you have a power cut, switch off the power or remove the plug. When power is restored, plug in the machine, press and
hold the ON/OFF button until the dryer reactivates, then press Start/Pause button.
14
EN
Sorting laundry
• Check the symbols on the care labels of the various gar-
ments to verify whether the garments can be safely tumble
dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
!
Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum kg
Synthetic fibres: maximum kg
! Do not overload the dryer as this may result is reduced
drying performance.
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
Drying times
Drying times are approximate and may vary depending on
the following:
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture
and thickness may have different drying times.
• Amount of laundry: single items and small loads may take
longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the
room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been shaken
out: repeat this procedure several times during the course
of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
The drying times provided refer to the automatic Cupboard
dry programmes.
The Timed drying settings are also indicated to enable you
to select the most suitable timed option.
The weight refers to dry items.
Laundry
Automatic drying times
Cottons - High Heat
Drying times after 800-1000 rpm wash cycles
1 kg
2 kg 3 kg 4 kg 5 kg 6 kg 7 kg 8 kg
Automatic
(hrs:mins)
1:00-1:30
1:20-1:40 1:40-2:10 2:00-2:20 2:30-3:00 2:30-3:10 2:50-3:20 3:20-4:00
Timed
(hrs:mins)
1:00 or 1:30 1:30 1:30 or 2:00 2:00 or 2:30 2:30 2:30 or 3:00 3:00 or 3:40 3:40
Synthetics - Low Heat
Drying times on reduced spin in washing machine
1 kg
2 kg 3 kg 4 kg
Automatic
(hrs:mins)
0:40 - 0:50 0:50 - 1:00 1:00 - 1:30 1:20 - 2:00
Timed
(hrs:mins)
0:40 or 1:00 0:40 or 1:00 1:00 or 1:30 1:00 or 1:30 or 2:00
Acrylics - Low Heat
Drying times on reduced spin in washing machine
1 kg
2 kg
Automatic
(hrs:mins)
0:40 - 1:20 1:20 - 2:20
Timed
(hrs:mins)
0:40 or 1:00 or 1:30 1:30 or 2:00 or 2:30
8
4
EN
15
Troubleshooting
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the
Technical Assistance Centre
(see Assistance).
The dryer does not start.
• The plug has not been inserted far enough into the socket to make contact.
• There has been a power cut.
• The fuse has blown. Try connecting another appliance to the same socket.
• If an extension cord is used, try connecting the dryer plug directly into the socket.
• The door has not been closed properly.
• The programme has not been set correctly (see How to carry out a drying cycle).
• The START/PAUSE button has not been pressed (see How to carry out a drying cycle).
• On machines equipped with “Locked” function, check the option is not enabled (see Programmes and options).
The drying cycle does not start.
• A delayed start time has been set (see Programmes and options).
• The START/PAUSE button has been pressed; a short delay follows before the dryer starts running. Wait for the drying cycle to
start; do not press the START/PAUSE button otherwise the dryer switches to the pause mode and the drying cycle will not start.
Drying times are too long.
• The filter has not been cleaned (see Maintenance).
• The water container must be emptied? The “Empty water container” indicator light flashes and the message appears “H2O”
(see Maintenance).
• The Heat Pump Filter needs cleaning (see Maintenance).
• The heat setting is not suited to the type of fabric to be dried (see Programmes and options).
• An incorrect drying time was selected for the type of load (see Laundry).
• The items are too wet (see Laundry).
• The air intake grille are clogged up (see “Installation” and “Care and Maintenance”).
• The dryer is overloaded (see Laundry).
The “Empty water container” indicator light flashes, but the dryer has been running for a short time.
• The water container was probably not emptied before starting the programme. Do not wait for the signal for emptying the
water container, but always check and empty it before starting a new drying programme (see Description of the tumble dryer).
The “Empty water container” indicator light is on but the water container is not full.
• It is normal: the “Empty water container” indicator light flashes when the water container is full. If the indicator light is on but is
not flashing, it is just a reminder to empty the container (see Description of the tumble dryer).
The programme is finished but the items are damper than expected.
! For safety reasons, the dryer programmes last a maximum of 5 hours. If an automatic programme has not detected the final
dampness level required in this interval, the dryer completes the programme and stops. Check the above points and repeat
the programme; if the items are still damp, contact the Technical Assistance Centre (see Assistance).
The code “F” appears on the display followed by one or two numbers, the options indicator lights and the
pause indicator light flash.
• If the display shows a fault, switch the appliance off and unplug it, then clean the filter and the Heat Pump Filter unit (see
Maintenance). Reinsert the plug, switch the appliance on and start another programme. If the display still visualises a fault,
contact the Technical Assistance Centre (see Assistance). If the display still visualises other numbers, mark the code and
contact the Technical Assistance Centre (see Assistance).
“dOn” briefly appears on the display every 6 seconds.
• The appliance is in “Demo” mode. Press the ON/OFF and START/PAUSE buttons and keep them pressed for 3 seconds. The
display visualises “dOn” for 3 seconds, then the dryer starts functioning normally.
The “Remaining time” indicator changes during the drying cycle.
• The remaining time is constantly monitored during the drying cycle and is updated to show the best forecast. It is normal for
the displayed time to increase during the cycle.
The dryer is noisy during the first few minutes of operation.
• This is normal, especially if the dryer has not been used for a long time. If the noise persists during the entire cycle, contact
the Technical Assistance Centre.
The lights on the dryer control panel are off although the dryer is switched on.
• The dryer has gone into standby mode to save power. This occurs if you have left the dryer on or have had a power cut. It
occurs after 30 minutes:
- if you leave the dryer without starting a programme;
- after your drying programme has finished.
Press the On/Off button and the lights will come on again.
16
EN
Assistance and guarantee
Heat Pump System
This dryer is fitted with a sealed heat pump system to dry your clothes. To operate, the heat pump contains fluorinated greenhouse
gases ( F gases) which are covered by the Kyoto Protocol. These F gases are contained in a hermetically sealed unit. This sealed
unit contains 0.29 kg of the F gas R134a which acts as a refrigerant.
If the sealed unit fails then it must be replaced by a new sealed unit. Contact your nearest service centre for advise.
Note: The gases contained in the sealed unit are not hazardous to health, but if they escape they will have an impact on global warming.
Before calling the Technical Assistance Centre:
• Follow the troubleshooting guide to check whether problems can be solved personally (see Troubleshooting).
• If not, switch the dryer off and contact the Technical Assistance Centre closest to you.
Spare parts
This dryer is a complex machine. Attempting to repair it personally or with the aid unqualified personnel may put the safety of people
at risk, damage the machine or invalidate the spare parts guarantee. Always contact a qualified technician when experiencing
problems with this machine. Please note that it is an offence for an unqualified person to undertaken any servicing or repair work that
involves breaking into the sealed heat pump unit.
This appliance conforms to the following EU directives:
- 2006/95/EC (Low Voltage Directive)
- 2004/108/EC (Electromagnetic Compatibility Directive).
Information on recycling and disposal
As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components
to reduce costs for our customers and to minimise materials wastage.
• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the
appliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.
Disposal of old household appliances
The European Directive 2012/19/EC on Waste Electricaland Electronic Equipment (WEEE), requires that oldhousehold
electrical appliances must not be disposedof in the normal unsorted municipal waste stream. Old appliances must be
collected separately in order tooptimise the recovery and recycling of the materialsthey contain and reduce the impact on
human healthand the environment. This dryer has a sealed heat pump unit containing Fgases which should be recovered
and destroyed.The crossed out “wheeled bin” symbol on theproduct reminds you of your obligation,thatwhen you dispose of
the appliance it must beseparately collected.Consumers should contact their local authority orretailer for information concer-
ning the correct disposalof their old appliance.
Product Guarantee And Repair Information
Guarantee
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the
date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or
materials, we will, at our discretion, either repair or replace the appliance at no cost to you:
This guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions.
- The appliance is used only on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to: plugs, cables, batteries, light bulbs, fluorescent
tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.
Repairs and After Sales
For product help and advice, repairs, spare parts or accessories, we’re here to help.
For local repair engineers - 03448 111 606 ROI - 0818 313 413 UK standard local rate applies ROI local Irish rate applies
For Parts and Accessories visit: parts.indesit.co.uk/shop
Please remember to register your appliance at www.indesitservice.co.uk to activate your 10 year parts guarantee.
Please note, our advisors will require the following information: model number, serial number.
This information can be found on the data plate located behind the door.
17
FR
Français
FR
Mode d’emploi
SÈCHE-LINGE
! Ce symbole vous rappelle de lire ce
mode d’emploi.
! Conservez cette notice d’utilisation et d’installation à portée de
main de manière à pouvoir vous y référer si nécessaire. Conservez
cette notice toujours à côté du sèche-linge et si vous vendez cet
appareil ou que vous le donniez à un tiers, faites en sorte que
cette notice accompagne le sèche-linge de manière à ce que le
nouveau propriétaire soit informé des avertissements et des con-
seils concernant le fonctionnement de ce sèche-linge.
! Lisez attentivement ce mode d’emploi : les pages suivantes
contiennent des informations importantes concernant l’installation
et des conseils relatifs au fonctionnement de cet appareil.
www.indesit.com
Table des matières
Installation, 18
Où installer le sèche-linge
Ventilation
Raccordement électrique
Informations préliminaires
Précautions, 20
Sécurité générale
Économie d’énergie et protection de l’environnement
Soin et entretien, 22
Interruption de l’alimentation électrique
Nettoyage du filtre après chaque cycle
Contrôle du tambour après chaque cycle
Vidange du réservoir d’eau après chaque cycle
Nettoyage du groupe filtre de ka pompe à chaleur
Nettoyage du sèche-linge
Description du sèche-linge, 24
Caractéristiques
Tableau de bord
Comment effectuer
un cycle de séchage, 26
Démarrage et choix du programme
Programmes et options, 27
Tableau des programmes
Programmes Spécial/Sport/Partiaux
Options
Ouverture de la porte
Linge, 30
Tri du linge
Étiquettes d’entretien
Temps de séchage
Problèmes et solutions, 31
Assistance, 32
Pièces détachées
Informations pour le recyclage et la mise au rebut
EDPE G45 A1
EDPE G45X A1
18
FR
Où installer le sèche-linge
• Placez votre sèche-
linge à une certaine
distance des cuisinières,
fourneaux, radiateurs,
ou plaques de cuisson
à gaz, car les flammes
peuvent endommager
cet appareil. Pour garantir
un fonctionnement
optimal, installez votre
sèche-linge dans une pièce à température
ambiante entre 20 et 23 °C. Cependant,
l’appareil fonctionnera si la température de la
pièce se situe entre 14 et 30 °C.
Si vous installez cet appareil sous un plan de
travail, faites en sorte de laisser un espace
de 10 mm entre le dessus de l’appareil et
tout autre objet sur ou au-dessus de celui-
ci, et un espace de 15 mm entre ses côtés
et les éléments d’ameublement ou les murs
latéraux. Ceci a pour objectif d’assurer une
ventilation convenable.
La surface arrière de l’appareil doit être
placée contre un mur.
Ventilation
• Lorsque le sèche-linge est en marche, une aération
adéquate est nécessaire. Faites en sorte d’installer votre
sèche-linge dans un environnement qui n’est pas humide
et qui est doté d’une bonne circulation d’air dans toute
la pièce. La circulation d’air autour du sèche linge est
essentielle pour condenser l’eau produite au cours du
lavage ; le sèche linge ne fonctionnera pas efficacement
dans un espace clos ou dans un placard.
! Si l’on utilise le sèche linge dans une pièce froide ou petite,
on rencontrera un certain degré de condensation.
! Nous vous déconseillons d’installer votre
sèche-linge dans un placard ; par ailleurs,
le sèche-linge ne doit en aucun cas être
placé derrière une porte fermant à clé, une
porte coulissante ou une porte montée sur
des gonds du côté opposé à la porte de
chargement du sèche-linge.
Vidange de l’eau
Si votre sèche-linge est installé à proximité d’une évacuation,
l’eau peut être vidangée directement dans ce tuyau. Cela
évite d’utiliser et de vider le réservoir d’eau.
Si vous installez le sèche-linge au-dessus ou à côté d’un
lave-linge, il pourra partager la même vidange. Il suffit de
débrancher le tuyau indiqué par la figure A et de le brancher
à la vidange.
Si la vidange est plus loin que la longueur du tuyau, il
possible d’acheter et de brancher un tuyau ayant le même
diamètre et la longueur nécessaire.
10 mm
15 mm
15 mm
Pour installer le nouveau il suffit de remplacer le tuyau exi-
stant comme illustré par la figure B dans la même position.
! La hauteur de la vidange doit être inférieure à 1 m en
partant du bas du sèche-linge.
! Assurez-vous que le tuyau n’est pas écrasé ou plié une
fois le sèche-linge placé dans sa position définitive.
1
2
2
1
Less than 1m
Fig. A Fig. B
Raccordement électrique
Assurez-vous des points suivants avant de
brancher la fiche de l’appareil dans la prise
de mains:
• Assurez-vous d’avoir les mains sèches.
• La prise de courant doit être reliée à la
terre.
• La prise de courant doit pouvoir supporter
la puissance maximale de la machine, qui
est indiquée sur la plaque signalétique de
l’appareil (voir Description du sèche-linge).
• La tension électrique doit appartenir à la
gamme de valeurs indiquée sur la plaque
signalétique de l’appareil (voir Description
du sèche-linge).
• La prise de courant doit être compatible
avec la fiche du sèche-linge. Autrement,
remplacez la prise ou la fiche.
! N’UTILISEZ PAS DE RALLONGES.
! Le sèche-linge ne doit pas être utilisé à
l’extérieur, même si l’espace en question est
abrité. Cela peut être dangereux si l’appareil
est exposé à la pluie ou à des orages.
! Une fois le sèche-linge installé, le cordon
d’alimentation et la fiche doivent être
d’accès facile.
! Le cordon d’alimentation ne doit pas être
courbé ou écrasé.
! Si la fiche à remplacer est de type
incorporée, il faut l’éliminer conformément
aux consignes de sécurité. Ne la laissez
Installation
19
FR
Consommation d'énergie à pleine charge ; Edry- kWh 2) 2.64
Consommation d'énergie à demi-charge ; Edry½,- kWh 2) 1.34
Consommation d'électricité : mode arrêt (Po) - Watts 0.14
Pleine charge (Tdry) - minutes 235
Demi-charge (Tdry½) - minutes 127
pondéré (Ct) pleine et demi-charge 3) 71
charge pleine Cdr 72
demi-charge Cdry½ 71
Niveau de bruit aérien - dB(A) re 1 pW 69.0
Synthétique: consommation d'énergie à pleine charge; kWh 0.92
Synthétique: pleine charge (Tdry) - minutes 90
2) La consommation annuelle est basée sur la base de 160 cycles de séchage pour
le programme coton standard à pleine charge et à demi-charge, et de la
consommation des modes à faible puissance. La consommation réelle d’énergie
par cycle dépend des conditions d’utilisation de l’appareil.
3) Moyenne pondérée de 3 cycles à pleine charge et de 4 cycles à demi-charge.
R
églementation 932/2012.
Synthétique: demi-charge N/A
Durée du programme - pondérée (Tt) pour pleine et demi-charge
- minutes
173
Classe de taux de condensation sur une échelle allant de G
(appareils les moins efficaces) à A (appareils les plus efficaces)
C
Taux de condensation moyen - %
1) Le « programme coton standard » à charge pleine ou partielle et le « programme
coton standard » à charge partielle sont les programmes standards auxquels se
réfèrent les informations de l'étiquette et de la fiche. Ces programmes sont parfaits
pour sécher du linge en coton au niveau armoire (0%) et ce sont aussi les
programmes les plus efficaces au point de vue consommation d'énergie. La charge
partielle est égale à la moitié de la charge nominale.
Ce sèche-linge domestique à tambour est un sèche-linge Automatique
Consommation d'électricité : mode laissé sur marche (Pl) - Watts
2.39
Durée du mode laissé sur marche pour le système de gestion de
la consommation d’électricité - minutes
30
Ce sèche-linge domestique à tambour est un sèche-linge À condens.
Classe d'efficacité énergétique de A+++ (faible consommation) à
D (consommation élevée)
A+
La consommation d’énergie annuelle (AEc)* pondérée Kwh 1) 306.0
D
onnées techniques - Réglementation 392/2012.
Marque
Indesit
Modèle
EDPE G45 A1 ECO (EU) - EDPE G45X A1 ECO (EU)
Capacité nominale de linge en coton pour le « programme coton
standard » à pleine charge - kg
8.0
jamais dans un endroit où elle peut être
branchée à une prise et provoquer ainsi un
choc électrique.
! Le câble électrique doit être contrôlé
périodiquement. Si le câble est endommagé,
il faut le faire remplacer par le fabricant, par
son service après-vente ou par tout autre
personnel qualifié afin d’éviter tout risque
de danger. (voir Service après-vente). Des
cordons d’alimentation neufs ou plus longs
sont fournis par les revendeurs agréés contre
un supplément..
! Le fabricant rejette toute responsabilité
en cas de non-respect de toutes ou partie
de ces règles.
! En cas de doute au sujet des points
précédents, consultez un électricien
qualifié.
Mise à niveau du sèche-linge
Le sèche-linge doit être installé sur une
surface plane pour un fonctionnement
optimal.
Après avoir installé le sèche-linge dans sa
position définitive, contrôler s’il est placé de
niveau dans le sens de la largeur dans un
premier temps et ensuite sur la profondeur.
Si le sèche-linge n’est pas de niveau, régler
les deux pieds avant jusqu’à atteindre une
position adéquate.
Informations préliminaires
Une fois que vous avez installé votre sèche-linge, et avant
de l’utiliser, nettoyez l’intérieur du tambour pour retirer les
poussières qui pourraient s’y être accumulées pendant le
transport.
ATTENTION : avant d’utiliser le sèche-linge, assurez-
vous qu’il est resté en position verticale pendant au
moins 6 heures.
Capacités maximales de chargement: 8 kg
20
FR
! Cet électroménager a été conçu et réalisé
conformément aux normes internationales de
sécurité. Ces consignes sont fournies pour
des raisons de sécurité, il faut les respecter
scrupuleusement.
Sécurité générale
• Ce sèche-linge peut être utilisé par des
personnes (notamment des enfants de
plus de 8 ans) présentant des capacités
physiques, motrices ou mentales
réduites, ou manquant d’expérience et de
connaissances, si elles sont placées sous
surveillance ou ont reçu les instructions
nécessaires à l’utilisation de l’appareil de la
part d’une personne responsable de leur
sécurité.
• Ce sèche-linge a été conçu pour un usage
domestique, et non professionnel.
• Ne touchez pas cet appareil lorsque vous
êtes pieds nus ou avec des mains ou des
pieds humides.
• Débranchez cette machine en tirant sur la
fiche et non sur le cordon.
• Après avoir utilisé ce sèche-linge, éteignez-
le et débranchez-le. Tenez la porte fermée
pour assurer que les enfants ne jouent pas
avec.
• Surveillez les enfants de façon à ne pas les
laisser jouer avec le sèche-linge.
• Le nettoyage et l’entretien ne doivent
pas être effectués par des enfants non
surveillés.
• Les enfants de moins de 3 ans doivent être
tenus à bonne distance du sèche-linge s’ils
ne sont pas sous surveillance constante.
• Cet appareil doit être installé correctement
et avoir une ventilation convenable.
L’arrivée d’air sur le devant du sèche-linge
et l’évent derrière le sèche-linge ne doivent
jamais être obstrués (voir Installation).
• N’utilisez jamais le sèche-linge sur de
la moquette où la hauteur des poils
empêcherait l’air d’entrer dans la sèche-
linge à partir de la base.
• Vérifiez que le sèche-linge est bien vide
avant de le charger.
• L’arrière du sèche-linge peut devenir
très chaud.
Ne le touchez jamais en cours d’utilisation.
• N’utilisez pas le sèche-linge si le filtre, le
réservoir d’eau et le condenseur ne sont
pas bien en place (voir Entretien).
• Ne surchargez pas le sèche-linge (voir
Linge pour les charges maximales).
• Ne chargez pas d’articles qui dégouttent
d’eau.
• Vérifiez avec soin toutes les instructions sur
les étiquettes des vêtements (voir Linge).
• Ne séchez pas d’articles de grande taille,
très volumineux.
• Ne séchez pas de fibres acryliques à
hautes températures.
• N’éteignez pas le sèche-linge s’il contient
encore des articles chauds.
• Nettoyez le filtre après chaque utilisation
(voir Entretien).
• Videz le réservoir d’eau après chaque
utilisation (voir Entretien).
• Nettoyez le groupe condenseur à
intervalles réguliers(voir Entretien).
• Ne laissez pas s’accumuler de peluches
autour du sèche-linge.
• Ne montez jamais sur le sèche-linge. Cela
pourrait l’endommager.
• Respectez toujours les normes et
exigences électriques (voir Installation).
• Achetez toujours des pièces de rechange
et accessoires d’origine (voir Service
Après-vente).
Vous devez observer les consigne
suivantes pour réduire tout risque
d’incendie dans votre sèche-linge :
• Ne séchez que des articles qui ont été
lavés avec de l’eau et un détergent, rincés
et essorés. Le fait de sécher des articles
qui N’ONT PAS été lavés avec de l’eau
constitue un danger d’incendie.
• Ne séchez pas des vêtements qui ont été
traités avec des produits chimiques.
• Ne placez pas d’articles tachés ou
imbibés d’huile végétale or de cuisson,
ils risqueraient de provoquer un incendie.
Les articles contenant de l’huile
peuvent prendre feu spontanément,
particulièrement lorsqu’ils sont exposés à
des sources de chaleur comme un sèche-
linge. En chauffant, les articles provoquent
une réaction d’oxydation avec l’huile
générant alors de la chaleur. Si la chaleur
ainsi générée ne peut pas être évacuée,
les articles peuvent devenir suffisamment
chauds pour prendre feu. Le fait d’empiler,
de superposer ou de stocker des articles
contenant de l’huile peut empêcher la
chaleur d’être évacuée et donc provoquer
un incendie. Si vous ne pouvez pas faire
autrement que de placer des articles
contenant de l’huile végétale ou de l’huile
Précautions
Loading...