Impex GS-9 User Manual

	NOTE:
	Please read all instructions
	carefully before using this
	product
	Table of Contents	POWERHOUSE
	Safety Notice
		CORNER GYM
	Hardware Pack
	Assembly Instruction	GS 9
	Parts List
	Resistance Chart
	Warranty
	Ordering Parts
	Model
	GS 9
	Retain This
	Manual for
	Reference
	10-14-03
	OWNER'S	IMPEX FITNESS PRODUCTS
	MANUAL
		14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
		Tel: [phone] Fax: [phone]
		www.impex-fitness.com
		[e-mail]

TABLE OF CONTENTS
BEFORE YOU BEGIN......................................................................................	1
IMPORTANT SAFETY NOTICES.....................................................................	2
HARDWARE PACK……….....…....................................................................... 3
ASSEMBLY INSTRUCTIONS...............................................................…..........5
EXPLODED DIAGRAM……………………………………………………………….26
PARTS LIST…………………………………………………………….……….…….28
RESISTANCE CHART……………………………………………………………….29
WARRANTY.................................................................................................… 30
ORDERING PARTS.........................................................................................	30

BEFORE YOU BEGIN

Thank you for selecting the POWERHOUSE GS-9 CORNER GYM by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. To avoid unnecessary delays, please call our TOLL-FREE customer service number. Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number 1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST www.impex-fitness.com [e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions:

1.Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine.

2.Only one person at a time should use the machine.

3.If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4.Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors.

5.Keep hands away from all moving parts.

6.Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine.

7.Use the machine only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer.

8.Do not place any sharp object around the machine.

9.Disabled person should not use the machine without a qualified person or physician in attendance.

10.Before using the machine to exercise, always do stretching exercises to properly warm up.

11.Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE PACK

3

HARDWARE PACK

4

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to each other. Attach the Rear Vertical Beam (#50) to the joint and align the holes. Secure the holes with two M10 x 2 ¾” Carriage Bolts (#64), 3/4” Washers (#6) and M10 Aircraft Nuts (#5). DO NOT tighten all the nuts and bolts yet.

Diagram 1

5

STEP 2 (See Diagram 2)

A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x 2 ½” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).

B.) Attach the Right Seat Support (#49) to the Right Vertical Beam. Secure it with one Bracket (#7), two M10 x 2 ½” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).

C.) Attach the other end of Right Seat Support (#49) to the Right Base Frame (#46). Secure it with one M10 x 2 ½” Carriage Bolt (#17), ¾” Washer (#6), and M10 Aircraft Nut (#5).

D.) Attach the Leg Developer (#40) to the front open bracket on the Right Seat Support. Secure it with a Leg Developer Axle (#41), two ¾” Washers (#6), and two M10 x ¾” Allen Bolts (#37).

6

STEP 3 (See Diagram 3)

A.) Slide two 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#22). Insert the two Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector

Stem (#67) onto the two Guide Rods (#22). Slide the Selector Stem over the Selector Rod (#69). Secure the Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts (#56). DO NOT install the plates yet.

B.) Repeat the Procedure A above to install another set of Guide Rods.

C.) Place the Upper Frame (#8) over the two sets of Guide Rods then onto top of Right

Vertical Beam (#21) and Rear Vertical Beam (#50).

D.) Secure each set of Guide Rods (#22) to the Upper Frame with two M10 x 1” Allen Bolts (#56) and ¾” Washers (#6).

E.) Secure the Right Vertical Beam (#21) to the Upper Frame with one Bracket (#7), two M10 x 2 ½” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).

F.) Attach top of Left Vertical Beam (#77) to the Upper Frame. Attach the bottom of Left Vertical Beam to the Left Base Frame (#87). Secure the bottom of Left Vertical Beam with two M10 x 2 ½” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).

G.)Secure the Left Vertical Beam (#77), Rear Vertical Beam (#50), and Upper Frame (#8) all together with two M10 x 2 ¾” Carriage Bolts (#64), ¾” Washers (#6), and M10 Aircraft Nuts (#5).

H.) Attach the Left Seat Support (#92) to the Left Vertical Beam (#77). Secure it with one

Bracket (#7), two M10 x 2 ½” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5). Attach the other end of Left Seat Support (#92) to the Left Base Frame (#87). Secure it with one M10 x 2 ½” Carriage Bolt (#17), ¾” Washer (#6), and M10 Aircraft Nut (#5).

I.) Securely tighten all nuts and bolts previously installed.

J.) Carefully tilt the machine on its side. (Help of another person is a MUST.) Secure the four Guide Rods (#22) to the Right Base Frame (#46) with four M10 x 1” Allen Bolts

(#56) from the bottom.

K.) Attach the bottom of Leg Press Frame (#84) to the bracket on the Left Base Frame (#87). Secure it with a M12 x 3” Allen Bolt (#89), two 7/8” Washers (#71), and one M12 Aircraft Nut (#57).

L.) Insert the Seat Incline Adjustment (#90) into the opening on the Left Seat Support (#92). Use a Lock Knob (#47) to securely hold the desired Seat height.

M.)Insert the Leg Press Plate (#76) into the Leg Press Frame. Use a Lock Knob (#47) to securely hold the Leg Press Plate in desired position.

7

DIAGRAM 3

8

STEP 4 (See Diagram 4)

A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼”

Front Press Axle (#60), two ¾” Washers (#6), and two M10 Aircraft Nuts (#5).

B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2

½” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).

DIAGRAM 4

9