Model No. IMEL3906.0
Serial No.
Write the serial number in the space above for reference.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are damaged or missing,
PLEASE DO NOT CONTACT THE STORE; please contact Customer Care.
IMPORTANT: You must note the product model number and serial number (see the drawing above) before contacting us:
CALL TOLL-FREE:
1-800-753-4645
Mon.–Fri. 6 a.m.–6 p.m. MST Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
www.imageservice.com
CAUTION
Read all precautions and instructions in this manual before using this equipment. Keep this manual for future reference.
USER'S MANUAL
www.imagefitness.com
new products, prizes, fitness tips, and much more!
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
The warning decals shown here have been applied in the locations shown. If a decal is missing or illegible, call the telephone number on the front cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal may not be shown at actual size.
IMAGE is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your elliptical exerciser before using your elliptical exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1.Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.
2.It is the responsibility of the owner to ensure that all users of the elliptical exerciser are adequately informed of all precautions.
3.Your elliptical exerciser is intended for home use only. Do not use your elliptical exerciser in a commercial, rental, or institutional setting.
4.Keep your elliptical exerciser indoors, away from moisture and dust. Place your elliptical exerciser on a level surface, with a mat beneath it to protect the floor or carpet. Make sure that there is enough clearance around your elliptical exerciser to mount, dismount, and use it.
5.Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6.Keep children under age 12 and pets away from your elliptical exerciser at all times.
7.Your elliptical exerciser should not be used by persons weighing more than 250 lbs. (113 kg).
8.Wear appropriate exercise clothes when exercising; do not wear loose clothes that could become caught on your elliptical exerciser. Always wear athletic shoes for foot protection.
9.Hold the handgrip pulse sensor or the upper body arms when mounting, dismounting, or using your elliptical exerciser.
10.Keep your back straight while using your elliptical exerciser; do not arch your back.
11.The pulse sensor is not a medical device. Various factors, including the user’s movement, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general.
12.When you stop exercising, allow the pedals to slowly come to a stop.
13.If you feel pain or dizziness while exercising, stop immediately and cool down.
14.Use your elliptical exerciser only as described in this manual.
3
BEFORE YOU BEGIN
Thank you for selecting the new IMAGE® 9.5 elliptical exerciser. The IMAGE 9.5 is an incredibly smooth exerciser that moves your feet in a natural elliptical path, minimizing the impact on your knees and ankles. Welcome to a whole new world of natural, ellipticalmotion exercise.
For your benefit, read this manual carefully before you use the exercise cycle. If you have questions after reading this manual, please see the front cover of this manual. To help us assist you, note the product
model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed under warranty, you must register the elliptical exerciser at www.imageservice.com/registration.
Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.
Fan |
Console |
Upper Body Arm |
Pulse Sensor |
Water Bottle Holder |
(no bottle is included) |
Upright |
Pedal Arm |
Ramp |
Wheel |
Side Shield |
Leveling Foot |
Pedal Disk |
Pedal |
4 |
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Assembly requires the included hex keys and your own adjustable wrench , Phillips screwdriver ,
and rubber mallet .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part is not in the parts bag, check to see if it has been preassembled.
Star Washer |
M8 Split |
M8 Washer |
M8 Large |
Wave Washer |
Large Wave |
(85)–6 |
Washer (95)–2 |
(64)–4 |
Washer (81)–2 |
(27)–2 |
Washer (20)–2 |
M8 Nylon |
M10 Nylon |
M4 x 16mm |
M4 x 19mm |
M4 x 22mm M8 x 25mm Patch |
|
Round Head |
|||||
Locknut (87)–2 |
Locknut (84)–4 |
Screw (93)–4 |
Screw (68)–6 |
Screw (66)–2 |
Screw (70)–6 |
M8 x 69mm Button Bolt (91)–2 |
M10 x 77mm Carriage Bolt (58)–4 |
||||
|
|
M8 x 63mm Bolt Set (67)–2 |
|
|
5
1.
To make assembly easier, read the information on page 5 before you begin assembling the elliptical exerciser.
Attach the Rear Stabilizer (35) to the Frame (1) with two M10 x 77mm Carriage
Bolts (58) and two M10 Nylon Locknuts (84).
2.Attach the Front Stabilizer (3) to the Frame (1) with two M10 x 77mm Carriage
Bolts (58) and two M10 Nylon Locknuts (84).
1 |
|
|
58 |
|
1 |
58 |
|
|
35 |
|
84 |
2 |
|
58 |
3 |
|
84 |
|
84 |
|
1 |
6
3. Apply a generous amount of the included |
3 |
|
|
|
grease to the Ramp Axle (74). |
|
|
|
|
|
|
|
|
|
Have a second person hold the Ramp (78) |
|
90 |
78 |
|
near the Frame (1) in the position shown. |
|
|
|
|
|
|
|
|
|
Insert the Ramp Axle (74) through the Ramp |
|
|
64 |
70 |
and the Frame. Tighten an M8 x 25mm Patch |
|
|
59 |
|
Screw (70), with an M8 Washer (64) and a |
|
|
|
|
Ramp Cover (59), into each end of the Ramp |
|
|
|
|
Axle. |
|
|
|
|
Next, pull the Ramp Pin (90) and align the |
|
|
|
|
Ramp (78) with one of the three holes in the |
|
|
|
|
Frame (1). Then, release the Ramp Pin into |
|
|
|
|
the Frame. Make sure the Ramp Pin is firm- |
|
|
|
|
ly engaged in the Frame. |
|
|
|
|
|
64 |
Grease |
1 |
|
|
74 |
|
|
|
|
70 |
|
|
|
|
|
|
|
|
|
|
59 |
|
|
4. Identify the Left Pedal Arm (21), which is |
4 |
|
|
|
marked with a “Left” sticker. |
|
|
|
|
|
|
19 |
|
|
|
|
|
|
Attach a Pedal (19) to the Left Pedal Arm (21) with three M4 x 19mm Screws (68) and three Star Washers (85).
Repeat this step for the Right Pedal
Arm (not shown).
85
21
85
68
7
5.Orient an Upper Body Leg (6) and a Ramp Wheel (24) as shown. Attach the Upper Body Leg and the Ramp Wheel to the Left Pedal Arm (21) with an M8 x 63mm Bolt Set (67) and two Wheel Covers (97).
Repeat this step for the Right Pedal Arm (not shown).
6.Apply a small amount of grease to a Crank Arm Spacer (45). Orient the Crank Arm Spacer so that the flange is on the side shown, and slide it onto the Left Crank Arm (42). Then, slide the Left Pedal Arm (21) onto the Left Crank Arm.
Apply a small amount of grease to a Large Wave Washer (20) and press it against the Left Pedal Arm (21). Then, tighten an
M8 x 25mm Patch Screw (70) with an M8 Washer (64) and a Pedal Leg Cover (23) into the end of the Left Crank Arm (42).
Repeat this step for the Right Pedal Arm and the Right Crank Arm (not shown).
5
6
24
97 67
21
97
Grease 67
6
42
Grease
45
21 20
70 64 23
8
7.Have a second person hold the Upright (2) near the Frame (1) as shown. Next, connect the Upper Wire Harness (18) to the Lower Wire Harness (38).
Attach the Upright (2) to the Frame (1) with two M8 x 69mm Button Bolts (91), two M8 Split Washers (95), and two M8 Nylon Locknuts (87). Be careful to avoid pinching the wires.
8.Attach the Water Bottle Holder (17) to the Upright (2) with two M4 x 22mm Screws (66).
7 |
|
|
2 |
|
|
|
18 |
|
87 |
38 |
|
|
1 |
|
|
95 |
91 |
8 |
|
|
17
2
66
9
9.The Console (10) requires four “D” batteries (not included); alkaline batteries are recommended. IMPORTANT: If the elliptical exerciser has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries into the Console. If you do not do this, the console displays or other electronic components may become damaged. Remove the battery cover from the bottom of the Console and insert four batteries into the battery compartment. Make sure the batteries are oriented as shown by the diagram inside the battery compartment. Then, reattach the battery cover.
Have a second person hold the Console (10) near the Upright (2) as shown. Connect the console wires to the Upper Wire Harness (18) and the Pulse Wire (11). Attach the Console (10) to the Upright (2) with four M4 x 16mm Round Head Screws (93). Be careful to avoid pinching the wires.
10.Identify the Left Upper Body Arm (4), which is marked with a “Left” sticker. Orient the Left Upper Body Arm so that the indicated tube is facing inward.
Lubricate the upper end of the left Upper Body Leg (6) using a small amount of the included high-temperature lubricant. Then, slide the Left Upper Body Arm (4) onto the Upper Body Leg.
Apply a generous amount of grease to the Pivot Axle (16). Then, insert the Pivot Axle through the Left Upper Body Arm (4), an Upper Body Arm Spacer (29), and the Upright (2). Make sure the Upper Body Arm
Spacer is oriented as shown, with the arrow pointed down.
9 |
|
10 |
|
11 |
|
93 |
|
|
Console Wires |
|
18 |
2 |
|
10 |
|
4 |
2 |
|
29 |
|
Tube |
Grease |
|
16 |
Arrow |
|
|
|
Lubricate |
|
6 |
10 |
|