Image IKTL73130, 760 Coolaire IKTL73130 Owner's Manual

Loading...

Model No. IKTL73130

Serial No.

Serial Number Decal

QUESTIONS?

If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our factory.

TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.

The trained technicians on our Customer Hot Line will provide immediate assistance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

CAUTION

Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference.

USER'S MANUAL

Visit our website at

www.imagefitness.com

new products, prizes, fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 HOW TO USE THE CHEST PULSE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: An EXPLODED DRAWING is attached in the center of this manual.

IMAGE is a registered trademark of ICON Health & Fitness, Inc.

2

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and information before operating the treadmill.

1.It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.

2.Use the treadmill only as described.

3.Place the treadmill on a level surface, with at least eight feet of clearance behind it and two feet on each side. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.

4.Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near water.

5.Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

6.Keep children under the age of 12 and pets away from the treadmill at all times.

7.The treadmill should be used only by persons weighing 250 pounds or less.

8.Never allow more than one person on the treadmill at a time.

9.Wear appropriate exercise clothes when using the treadmill. Do not wear loose clothes that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals.

10.When connecting the power cord (see page 11), plug the power cord into a grounded circuit. No other appliance should be on the same circuit. When replacing the fuse, an ASTA approved BS1362 type should be fitted to the fuse carrier. A 13 amp fuse should be used.

11.If an extension cord is needed, use only a 3- conductor, 1mm2 (14-gauge) cord that is no longer than 5 ft.

12.Keep the power cord away from heated surfaces.

13.Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)

14.Never start the treadmill while you are standing on the walking belt. Always hold the handrails while using the treadmill.

15.The treadmill is capable of high speeds. Adjust the speed in small increments to avoid sudden jumps in speed.

16.The pulse sensors are not medical devices. Various factors, including the user's movement, may affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in determining heart rate trends in general.

17.Never leave the treadmill unattended while it is running. Always remove the key, unplug the power cord and switch the on/off switch to the off position when the treadmill is not in use. (See the drawing on page 5 for the location of the circuit breaker.)

18.Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 24.) You must be able to safely lift 45 pounds (20 kg) to raise, lower, or move the treadmill.

19.When folding or moving the treadmill, make sure that the storage latch is fully closed.

3

20.When using iFIT.com CDs and videos, an electronic “chirping” sound will alert you when the speed of the treadmill is about to change. Always listen for the “chirp” and be prepared for speed changes. In some instances, the speed may change before the personal trainer describes the change.

21.When using iFIT.com CDs and videos, you can manually override the speed setting at any time by pressing the speed buttons.

However, when the next “chirp” is heard, the speed will change to the next setting for the CD or video program.

22.Remove iFIT.com CDs and videos from your CD player or VCR when you are not using them.

23.Inspect and properly tighten all parts of the treadmill regularly.

24.Never insert any object into any opening.

25.DANGER: Always unplug the power cord immediately after use, before cleaning the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the procedures in this manual should be performed by an authorized service representative only.

26.This treadmill is intended for in-home use only. Do not use this treadmill in a commercial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decals shown have been placed on your treadmill. If a decal is missing, or if it is not legible, please call our Customer Service Department, toll-free, to order a free replacement decal (see the front cover of this manual). Apply the decal in the location shown.

4

BEFORE YOU BEGIN

Thank you for selecting the revolutionary IMAGE® 760 treadmill. The 760 treadmill combines advanced technology with innovative design to help you get the most from your exercise program in the convenience and privacy of your home. And when you’re not exercising, the unique 760 treadmill can be folded up, requiring less than half the floor space of other treadmills.

For your benefit, read this manual carefully before using the treadmill. If you have questions after reading this manual, please call our Customer Service

Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is IKTL73130. The serial number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).

Before reading further, please review the drawing below and familiarize yourself with the labeled parts.

Accessory Tray

Fan

Handrail

Storage Latch

Upright

Walking Belt

Foot Rail

BACK

Rear Roller

Adjustment Bolts

CD Holder

Console

Key/Clip

On/Off Switch

Circuit Breaker

Power Cord

RIGHT SIDE

Cushioned Walking Platform for maximum exercise comfort

5

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials except for the packing materials around the brackets on the uprights (see step 1). Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-perfor- mance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrenches

and your own phillips screwdriver

and wire cutters

.

 

Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag, check to see if it has been preattached to one of the parts to be assembled.

3/4” Screw (108)–10

1” Tek Screw (80)–2

 

 

 

 

1/4” Washer

1/4” Silver Star

 

5/16” Star

 

(39)–4

Washer (77)–4

 

 

Washer (36)–4

 

 

 

Silver Ground

 

 

 

 

Screw (103)–1

 

 

 

 

 

2 1/2” Bolt (61)–4

 

 

 

 

 

4” Bolt (76)–4

 

Extension Leg Bolt (96)–4

 

 

 

 

1. Make sure that the power cord is unplugged.

 

 

 

 

With the help of another person, carefully tip the tread-

1

74

 

 

 

 

 

 

 

 

 

mill onto its left side. Partially fold the Frame (59) so the

 

 

 

 

treadmill is more stable. Do not fully fold the treadmill

 

 

 

 

until it is completely assembled.

 

 

 

 

Identify the Left Upright (29) and the Right Upright (30);

 

30

 

97

 

 

 

 

the indicated brackets on the Uprights overhang toward

Brackets

 

 

 

the center of the treadmill. Make sure there are two U-

 

36

 

Nuts (122) (see the inset drawing) in the lower end of

 

 

 

 

 

 

61

each Upright. Feed the Wire Harness (74) into the bot-

 

 

 

29

 

 

 

tom of the Right Upright, and pull the Wire Harness out

 

 

 

 

 

 

 

of the hole in the top of the Right Upright. Note: There

 

 

 

 

may be a tie on the Wire Harness to help you pull it out

 

 

 

 

of the hole.

 

 

59

 

 

 

 

 

Attach the Right Upright (30) to the right side of the Base

 

 

 

 

(97) with two 2 1/2” Bolts (61) and two 5/16” Star

 

 

 

 

Washers (36). Do not tighten the Bolts yet. Be careful

1a

29, 30

 

 

not to damage the Wire Harness (74). Attach the Left

 

 

 

122

 

 

Upright (29) to the left side of the Base in the same way.

 

 

 

 

 

 

 

Note: There is not a wire on the left side.

 

 

 

 

 

 

 

36

61

 

 

 

 

6

2.Insert one of the Extension Legs (92) into the Upright Base (97). Make sure that the decal is in the indicated location.

Insert the other Extension Leg (92) in the same way.

With the help of a second person, carefully tip the treadmill so the Upright Base (97) is flat on the floor.

3.With the help of a second person, carefully tip the Left and Right Uprights (29, 30) down as shown. (Note: It may be helpful to place your foot on one of the Extension Legs [92] as you tip the Uprights.) Make sure that the Extension Legs remain in the Uprights.

Attach the two Base Pads (99) to the Upright Base (97) in the locations shown with two 1” Tek Screws (80).

Attach each Extension Leg (92) with two Extension Leg Bolts (96) and two 1/4” Washers (39) as shown. Thread the two Leveling Feet (95) into the Upright Base (97); do not thread the Leveling Feet fully into the Upright Base.

With the help of a second person, raise the Uprights (29, 30) to the vertical position. Remove the packing materials from the brackets on the Uprights.

4.Hold the Pulse Bar (71) in the position shown. Locate the pulse wire on the Pulse Bar. Insert the pulse wire into the side of the Left Upright (29) and out of the top as shown. Next, locate the ground wire on the Pulse Bar. Insert the ground wire through the indicated slot in the bracket on the Right Upright (30) (see the left inset drawing). Attach the Pulse Bar to the brackets on the Uprights (29, 30) with two 3/4” Screws (108). Make sure that the Screws are in the holes shown in the inset drawings. Note: Press the ends of the Pulse Bar onto the brackets as you tighten the Screws. Make sure no wires are pinched.

Insert the Silver Ground Screw (103) into the ring on the ground wire and tighten the Ground Screw into the indicated hole in the bracket. Make sure that the ring on the ground wire is turned as shown and that the ground wire is parallel to the bracket. Insert the excess wire back into the slot.

2

 

 

 

 

 

 

Decal

 

 

 

 

 

 

92

 

 

 

 

 

 

 

 

 

 

97

 

 

 

 

 

92

 

 

3

 

 

29

 

 

99

 

 

 

 

 

 

 

 

 

 

 

 

80

 

99

 

 

 

 

 

 

 

 

 

 

 

61

 

 

 

 

80

 

95

 

 

 

 

 

39

 

 

 

 

 

 

92

96

 

 

 

 

61

 

 

30

 

 

96

 

 

 

 

 

 

 

 

92

 

 

 

95

 

 

39

96

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

Pulse

 

Slot

 

 

 

 

Wire

 

 

 

 

 

 

 

108

103

71

108

 

Ground Wire

 

103

108

108

29

30

 

7

5.The box inside of the Pulse Bar (71) fits into a cavity in the pulse bar bottom; orient the pulse bar bottom so the box is inside of the cavity. Attach the pulse bar bottom with eight 3/4” Screws (108). Tighten the Screws indicated by the arrows first, and tighten the center Screws last. Be careful not to overtighten the Screws or to pinch any wires.

Insert the Wire Harness (74) and the pulse wire through the holes in the Top Endcaps (75). Press the Top Endcaps into the Uprights (29, 30), with the holes at the top as shown.

6.Remove the two Latch Screws (79) from the Left Upright (29). Attach the Latch Housing (82) to the Left Upright with the two Latch Screws. Make sure that the large hole in the Latch Housing is on the side shown

Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Insert the pin into the Latch Housing (82) and tighten the knob back onto the pin.

7.See drawing 7c. With the help of a second person, hold the Console Base (101) near the Uprights (29, 30). Look under the Console Base and locate the wires on the sides of the Console Base. Make sure that the wires are not routed through the openings for the Trays (109, 111). Drawing 7a shows the correct route for the wires. Drawing 7b shows an incorrect route.

Locate the Wire Harness (74) and the pulse wire in the Uprights (29, 30). Connect the Wire Harness and the pulse wire to the connectors on the sides of the Console Base (101). Make sure to connect the connectors properly (see the inset drawings). IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn a connector and try to insert it again. Insert the excess Wire Harness and pulse wire up into the Console Base.

5

 

Pulse Wire

 

 

74

Box

71

75

 

 

 

 

 

75

 

 

 

 

108

108

108

 

Pulse Bar

30

 

Bottom

29

6

 

 

Knob

29

 

82

 

79

 

Spring

 

 

Large

 

Pin

Hole

 

Collar

7a

 

7b

Correct

 

Incorrect

7c

 

 

111

109

 

 

74

101

 

 

 

30

 

29

 

 

Pulse

 

74

Wire

 

 

8

8.Set the Console Base (101) on the Uprights (29, 30). Insert any wires into the Uprights. Thread four 4” Bolts (76) with four 1/4” Silver Star Washers (77) into the Uprights and the Console Base. Be careful not to pinch the Wires (not shown) in the Uprights. Tighten the two Upright Bolts indicated by the arrows first; then, tighten the other two Upright Bolts.

Make sure that the Left and Right Trays (109, 111) are pressed into the Console Base (101).

See step 3. Lower the Uprights (29, 30) to the floor as shown. Make sure the frame is centered between the Uprights (29, 30). Firmly tighten the four 2 1/2” Bolts (61) Raise the Uprights.

9.Fold the treadmill to the storage position (see page 24).

If the Wheels (94) are resting on the floor or if the treadmill rocks slightly, turn one or both of the Leveling Feet (95) under the Upright Base (97) until the Wheels are off the floor and the rocking motion is eliminated. Note: If necessary, tip the treadmill and use a phillips screwdriver to turn the Leveling Feet.

8

 

 

101

 

 

 

 

 

 

 

 

 

29

 

 

111

109

 

 

 

 

77

 

 

 

77

 

 

76

 

30

76

77

 

 

 

 

9

 

 

 

 

 

 

 

97

 

 

94

95

 

 

 

 

 

 

 

 

 

94

 

10.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the walking belt (see page 27). To protect the floor or carpet, place a mat under the treadmill. If there are thin sheets of clear plastic on the decals, remove them.

9

HOW TO USE THE CHEST PULSE SENSOR

HOW TO PUT ON THE CHEST PULSE SENSOR

The chest pulse sensor consists of two components: the chest strap and the sensor unit (see the drawing below). Insert the tab on one end of the chest strap into one end of the sensor unit, as shown in the inset drawing. Press the end of the sensor unit under the buckle on the chest strap. The tab should be flush with the front of the sensor unit.

 

Chest Strap

 

Tabs

 

 

 

Tab

Sensor Unit

Sensor

Buckle

Unit

 

 

Next, wrap the chest pulse sensor around your chest and attach

the other end of

the chest strap to the sensor unit. Adjust the length

of the chest strap, if necessary. The chest pulse sen-

sor should be under your clothes, tight against your skin, and as high under the pectoral muscles or breasts as is comfortable. Make sure that the logo on the sensor unit is facing forward and is right-side-up.

Pull the sensor unit away from your body a few inches and locate the two electrode areas on the inner side (the electrode areas are covered by shallow ridges). Using saline solution such as saliva or contact lens solution, wet both electrode areas. Return the sensor unit to a position against your chest.

CHEST PULSE SENSOR CARE AND MAINTENANCE

Thoroughly dry the chest pulse sensor after each use. The chest pulse sensor is activated when the electrode areas are wetted and the heart rate monitor is put on; the chest pulse sensor shuts off when it is removed and the electrode areas are

dried. If the chest pulse sensor is not dried after each use, it may remain activated longer than necessary, draining the battery prematurely.

Store the chest pulse sensor in a warm, dry place. Do not store the chest pulse sensor in a plastic bag or other container that may trap moisture.

Do not expose the chest pulse sensor to direct sunlight for extended periods of time; do not expose it to temperatures above 122° Fahrenheit (50° Celsius) or below 14° Fahrenheit (-10° Celsius).

Do not excessively bend or stretch the sensor unit when using or storing the chest pulse sensor.

Clean the sensor unit using a damp cloth—never use alcohol, abrasives, or chemicals. The chest strap may be hand washed and air dried.

CHEST PULSE SENSOR TROUBLESHOOTING

The instructions on the following pages explain how the chest pulse sensor is used with the console. If the chest pulse sensor does not function properly, try the steps below.

Make sure that you are wearing the chest pulse sensor as described at the left. Note: If the chest pulse sensor does not function when positioned as described, move it slightly lower or higher on your chest.

Use saline solution such as saliva or contact lens solution to wet the two electrode areas on the sensor unit. If heart rate readings do not appear until you begin perspiring, re-wet the electrode areas.

As you walk or run on the treadmill, position yourself near the center of the walking belt. For the console to display heart rate readings, the user must be within arm’s length of the console.

The chest pulse sensor is designed to work with people who have normal heart rhythms. Heart rate reading problems may be caused by medical conditions such as premature ventricular contractions (pvcs), tachycardia bursts, and arrhythmia.

The operation of the chest pulse sensor can be affected by magnetic interference caused by high power lines or other sources. If it is suspected that this is a problem, try relocating the treadmill.

The CR2032 battery may need to be replaced (see page 28).

10

TREADMILL OPERATION

THE PERFORMANT LUBETM WALKING BELT

Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPOR-

TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a power cord having an equipment-grounding conductor and a grounding plug.

Plug the indicated end of the power cord into the socket on the treadmill.

See drawing 2. Plug the power cord into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. Important: The treadmill is not compatible with GFCI-equipped outlets.

Important: If the power cord is damaged, it must be replaced with a manufacturer-recommended power cord.

1

Socket on treadmill

2

Outlet

DANGER: Improper connection of the equipment-earthing conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

11

+ 23 hidden pages