Loading...
IBM
Technical Information Manual
PC 300GL Types 6563, 6564, 6574
PC 300PL Type 6565
IBM
Technical Information Manual
PC 300GL Types 6563, 6564, 6574
PC 300PL Type 6565
Note:
Before using this information and the product it supports, be sure to read the general infromation under “Appendix E. Notices and Trademarks,” on page 57.
Technical Information Manual IBM PC 300GL Types 6563, 6564, 6574 and PC300PL Type 6565
Second Edition (March 2000)
© COPYRIGHT INTERNATIONAL BUSINESS MACHINES CORPORATION, 2000. All rights reserved.
Note to U.S. Government Users — Documentation related to restricted rights — Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Chapter 1.System Overview . . . . . . . . . . . . 1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DVD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ADSL modems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Wake on LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Wake on Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 2.System board features . . . . . . . 5
Intel Pentium III microprocessor with MMX technology 5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 L2 Cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chip set control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 System memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PCI Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 IDE bus master interface. . . . . . . . . . . . . . . . . . . . . . . . 7 USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Video Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Audio Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Integrated peripheral controller . . . . . . . . . . . . . . . . . . . 11 Diskette Drive Interface . . . . . . . . . . . . . . . . . . . . . . . 11 Serial ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Parallel port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Keyboard and mouse ports . . . . . . . . . . . . . . . . . . . . 12 Network connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Real-time clock and CMOS . . . . . . . . . . . . . . . . . . . . . . . 13 Flash EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Expansion adapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Physical layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Rocker switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connector panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3.Physical specifications . . . . . . 21
PC 300 GL and PL desktop . . . . . . . . . . . . . . . . . . . . . . . 21 PC300 PL and GL tower . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Chapter 4.Power supply . . . . . . . . . . . . . . 25
Power input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Power output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Component outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Output protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Connector description . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 5.System software. . . . . . . . . . . . 29
BIOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
v
Plug and Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Configuration/Setup Utility program . . . . . . . . . . . . . . 30 Advanced Power Management (APM) . . . . . . . . . . . . . 30 Advanced Configuration and Power Interface (ACPI) 30 Flash update utility program . . . . . . . . . . . . . . . . . . . . . . 30 Diagnostic program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Chapter 6.System compatibility . . . . . . . . 31
Hardware compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Hardware interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Software compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Software interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Machine-sensitive programs. . . . . . . . . . . . . . . . . . . . 32
Appendix A. Connector pin assignments 33
SVGA monitor connector . . . . . . . . . . . . . . . . . . . . . . . . . 33 DVI-I monitor connector . . . . . . . . . . . . . . . . . . . . . . . . . 34 System memory connector . . . . . . . . . . . . . . . . . . . . . . . . 34 PCI connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 IDE connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Diskette drive connector. . . . . . . . . . . . . . . . . . . . . . . . . . 43 Power supply connector . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Wake on LAN connectors. . . . . . . . . . . . . . . . . . . . . . . . . 44 USB port connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Mouse and keyboard port connectors . . . . . . . . . . . . . . 45 Serial port connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Parallel port connector . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Appendix B. System address maps. . . . . 47
System memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Input/output address map . . . . . . . . . . . . . . . . . . . . . . . 48 DMA I/O address map. . . . . . . . . . . . . . . . . . . . . . . . . . . 50 PCI configuration space map. . . . . . . . . . . . . . . . . . . . . . 51
Appendix C. IRQ and DMA channel assignments. . . . . . . . . . . . . . . . . . . . . . . 53
Appendix D. Error codes . . . . . . . . . . . . . 55
POST error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Beep codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Appendix E. Notices and Trademarks . . . 57
Bibliography. . . . . . . . . . . . . . . . . . . . . . . . 59
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
vi
Preface
This Technical Information Manual provides information for the IBM PC 300GL personal computer types 6563, 6564, 6574 and PC 300PL personal computer type 6565. The Manual is intended for developers who want to provide hardware and software products to operate with these IBM computers and provides an in-depth view of how these IBM computers work. Users of this publication should have an understanding of computer architecture and programming concepts.
Related publications
In addition to this Manual, the following IBM publications provide information related to the operation of the IBM PC 300GL and PC 300PL personal computer. Several publications mentioned in this book are available from the IBM Web site. In some cases, you will have to follow further instructions on the Web site to find the document for your particular computer and model. To order printed publications in the U.S. and Puerto Rico, call 1-800-879-2755. In other countries, contact an IBM reseller or an IBM marketing representative.
•PC 300GL and PC 300PL User Guide
This publication contains information about configuring, operating, and maintaining the PC 300GL and the PC 300PL personal computer, as well as installing new options in the PC 300GL and PC 300PL personal computer. Also included are warranty information, instructions for diagnosing and solving problems, and information on how to obtain help and service.
•Understanding Your Personal Computer
This online document includes general information about using computers and detailed information about the features of the PC 300GL and the PC 300PL personal computer. This publication is available on the World Wide Web at http://www.ibm.com/pc/support.
•About Your Software
This publication (provided only with computers that have IBM-preinstalled software) contains information about the preinstalled software package.
•Hardware Maintenance Manual
This publication contains information for trained service technicians. It is available at http://www.ibm.com/pc/support on the World Wide Web, and it can also be ordered from IBM. To purchase a copy, see the "Getting Help, Service, and Information" section in the PC 300GL and PC 300PL User Guide.
•Compatibility Report
This publication contains information about compatible hardware and software for the PC 300GL and PC 300PL personal computer. It is available at http://www.ibm.com/pc/us/cdt on the World Wide Web.
•Network Administrator’s Guide
This publication contains information for network administrators who configure and service local area networks (LANs). Look for this publication at http://www.ibm.com/pc/us/cdt on the World Wide Web.
© Copyright IBM Corp. 2000 |
vii |
Terminology
Attention: The term reserved describes certain signals, bits, and registers that should not be changed. Use of reserved areas can cause compatibility problems, loss of data, or permanent damage to the hardware. If you change the contents of a register, preserve the state of the reserved bits. When possible, read the register first and change only the bits that must be changed.
In this manual, some signals are represented in an all-capital-letter format
(-ACK). A minus sign in front of the signal indicates that the signal is active low. No sign in front of the signal indicates that the signal is active high.
The term hex indicates a hexidecimal number.
When numerical modifiers such as K, M, and G are used, they typically indicate powers of 2, not powers of 10. For example, 1 KB equals 1 024 bytes (210), 1 MB equals 1 048 576 bytes (220), and 1 GB, equals 1 073 741 824 bytes (230).
When expressing storage capacity, MB equals 1 000 KB (1 024 000). The value is determned by counting the number of sectors and assuming thatevery two sectors equals 1 KB.
Note: Depending on the operating system and other requirements, the storage capacity available to you might vary.
viii PC 300 GL and 300 PL
Chapter 1. System Overview
IBM® PC 300® GL personal computer types 6563, 6564, and 6574 and PC 300PL personal computer type 6565 are computer systems that provide state-of-the-art computer power with room for future growth.
Features
Your computer has:
•An Intel® Pentium® III microprocessor with MMX™ technology, streaming single instruction multiple date (SMID) extensions, and 512 KB L2 cache
Your computer may have all, or some, of the following major features:
•Room for up to 1 GB of system memory total
•Integrated IDE bus master controller, Ultra DMA-66 capable
•EIDE hard disk drive
•System management
—Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)
—Wake on LAN® support
—Desktop Management Interface (DMI) BIOS and DMI software
—Integrated network protocols
—Enablement for Remote Administration
—Ability to update POST and BIOS over the network
—Wake on Ring support
—Automatic power-on startup
—System Management (SM) BIOS and software
—Ability to store POST hardware test results
—Selectable startup sequence
—Selectable Automatic Power ON Startup Sequence
—CMOS Save/Restore utility program
—CMOS setup over LAN
•IDE CD-ROM1 drive, standard on some models
•CD-RW (Rewritable) drive, standard on some models
•DVD-ROM drive, standard on some models
•Asynchronous Digital Subscriber Line (ADSL) modem, standard on some models
•Asset security
—Security settings provided by the Configuration/Setup Utility program:
–Power-on and administrator password protection
–Startup sequence control
–Hard disk drive and diskette drive access control
–I/O port control
—Cover lock loop (PC 300GL models only)
—Cover key lock (PC 300PL models only)
—U-bolt and security cabling (optional)
1.Variable read rate. Actual playback speed will vary and is often less than the maximum possible.
© Copyright IBM Corp. 2000 |
1 |
—Diskette write-protection™
—Alert on LAN
•Accelerated graphics port (AGP) video adapter with up to 16 MB of Synchronous Graphics Random Access Memory (SGRAM)
•Integrated 16-bit audio controller and built-in high-quality speaker (supports SoundBlaster, Adlib, and Microsoft® Windows® Sound System applications)
•Networking
—IBM 10/100 megabits-per-second (Mbps) PCI Ethernet adapter with Wake on LAN in some models
—IBM PCI token-ring adapter with Wake on LAN support (optional)
•Expansion: four drive bays, three PCI expansion slots
•PCI I/O bus compatibility
•EnergyStar compliance (some models only)
•3.5-inch, 1.44 MB diskette drive
•Input/Output features
—One 25-pin, ECP/EPP parallel port
—Two 9-pin, 16550 universal asynchronous receiver/transmitter (UART) serial ports
—Two 4-pin, Universal Serial Bus (USB) ports
—One 6-pin, keyboard port
—One 6-pin, mouse port
—One 15-pin, DDC2B-compliant monitor port or
—One 24-pin, DVI-I port on the AGP adapter (on some models)
—Three 3.5-mm audio jacks (in/headphone out, line in, microphone)
CD-RW
CD-Rewritable (CD-RW) drives, standard on some models, enable the recording and reuse of CD recordable media. The laser used in CD-RW has variable temperatures to provide the three functions of CD-RW drives: playing CDs or CD-RWs, erasing CD-RWs, and recording CD-RWs.
CD-RW drives can read traditional CDs, but many older CD players cannot read CD-RWs. Their light reflective properties are about one-third that of traditional CDs. CD-RW drives cannot read DVDs.
To learn more about CD-RW drives, see the Understanding Your Personal Computer publication for your personal computer model and type number. This publication is available on the World Wide Web at http://www.ibm.com/pc/support.
DVD-ROM
DVD-ROM drives, standard on some models, differ from CD-ROM and CD-RW drives as the result of refinements in laser technology.
The recording tracks on DVD media are not as deep and are more condensed than on CDs or CD-RWs, therefore DVDs provide more storage space. DVD media also use both sides of the disk, as opposed to just one side for CDs and CD-RWs.
DVD-ROM drives read traditional CDs, CD-RWs, and DVDs.
To learn more about DVD-ROM drives, see the Understanding Your Personal Computer publication for your personal computer model and type number. This publication is available on the World Wide Web at http://www.ibm.com/pc/support.
2 PC 300 GL and 300 PL
ADSL modems
ADSL modems, available on some models, enable simultaneous internet connectivity and telephone service. Contact your local telephone service provider and ask if your premises need any additional telephony equipment, such as a splitter or a filter. Also contact your Internet service provider (ISP) to determine if they provide service to customers with ADSL.
ADSL modems work by using separately the individual four or six wires in the standard RJ-11 telephone jack. The inner wires, or pairs of wires if there are six, carry voice transmissions. The outer wires on either side carry data between your computer and the Internet. One channel is data download; the other is data upload.
To learn more about ADSL modems, see the Understanding Your Personal Computer publication for your personal computer model and type number. This publication is available on the World Wide Web at http://www.ibm.com/pc/support.
Wake on LAN
The power supply of the computer supports the Wake on LAN feature. With the Wake on LAN feature, the computer can be turned on when a specific LAN frame is passed to the computer over the LAN.
To use the Wake on LAN feature, your computer must be equipped with a network adapter that supports Wake on LAN.
To find out if the Wake on LAN feature is set, refer to the menu item for Wake on LAN in the Configuration/Setup Utility program. See the PC 300GL and PC 300PL User Guide for help with using the Configuration/Setup Utility program.
Wake on Ring
All models can be configured to turn on the computer after a ring is detected from an external or internal modem. Use the menu for setting the Wake on Ring feature in the Configuration/Setup Utility Program. Two options control this feature:
•Serial Ring Detect: Use this option if the computer has an external modem connected to the serial port.
•Modem Ring Detect: Use this option if the computer has an internal modem.
Chapter 1. System Overview 3
4 PC 300 GL and 300 PL
Chapter 2. System board features
This section includes information about system board features. For an illustration of the system board, see “Physical layout” on page 14.
Intel Pentium III microprocessor with MMX technology
PC 300 GL personal computer types 6563, 6564, and 6574 and PC 300 PL personal computer type 6565 come with an Intel Pentium III microprocessor. The microprocessor has an attached heat sink which plugs directly into a connector on the system board.
More information on this microprocessor is available at http://www.intel.com on the World Wide Web.
Features
The features of the Pentium III microprocessor are as follows:
•Optimization for 32-bit software
•Operation at a low voltage level
•Intel microprocessor serial number
•64-bit microprocessor data bus
•100-133 MHz front-side bus (FSB)
•Math coprocessor
•Internet Streaming SIMD extensions
•MMX technology, which boosts the processing of graphic, video, and audio data
L2 Cache
The Pentium III microprocessor provides up to 512 KB L2 cache. The L2 cache error corrected code (ECC) function is automatically enabled if ECC memory is installed. If nonparity memory is installed, the L2 cache is non-ECC.
Chip set control
The chip set design is the interface between the microprocessor and the following:
•Memory subsystem
•PCI bus
•IDE bus master connection
•High performance, PCI-to-ISA bridge
•USB ports
•SMBus
•Enhanced DMA controller
•Real-time clock (RTC)
System memory
The maximum amount of system memory the computer can physically accommodate is 1 GB total. The amount of system memory factory-preinstalled varies by model.
© Copyright IBM Corp. 2000 |
5 |
For memory expansion, the system board provides two dual inline memory module (DIMM) connectors and supports 133 MHz DIMMs in sizes of 64 MB, 125 MB, and 512 MB. 100 MHz DIMMs may be used in systems with a 100 MHz FSB.
The following information applies to system memory:
•Synchronous dynamic random access memory (SDRAM) is standard.
•The maximum height of memory modules is 6.35 cm (2.5 in.).
•Only PC 100 and PC 133 industry-standard, gold-lead DIMMs are supported.
•DIMM connectors do not support RAMBUS Inline Memory Modules (RIMMs).
•The PC 300GL supports error-corrected code (ECC). A mix of nonparity types configures as nonparity.
•BIOS sepcific auto-configure, auto-detect maximum system memory.
For information on the pin assignments for the memory modules connectors, see “System memory connector” on page 34.
The following table shows some possible configurations for the supported DIMMs.
Table. 1. Memory Configuration (MB)
Total Memory |
Mem O |
Mem 1 |
|
|
|
64 |
64 |
0 |
|
|
|
96 |
64 |
32 |
|
|
|
128 |
64 |
64 |
|
|
|
128 |
128 |
0 |
|
|
|
160 |
128 |
32 |
|
|
|
192 |
128 |
64 |
|
|
|
256 |
128 |
128 |
|
|
|
384 |
256 |
128 |
|
|
|
512 |
256 |
256 |
|
|
|
512 |
512 |
0 |
|
|
|
578 |
512 |
64 |
|
|
|
640 |
512 |
128 |
|
|
|
1024 |
512 |
512 |
|
|
|
6 PC 300 GL and 300 PL
PCI Bus
The PCI bus originates in the chip set. Features of the PCI bus are:
•Integrated arbiter with multitransaction PCI arbitration acceleration hooks
•Zero-wait-state, microprocessor-to-PCI write interface for high-performance graphics
•Built-in PCI bus arbiter
•Microprocessor-to-PCI memory write posting
•Conversion of back-to-back, sequential, microprocessor-to-PCI memory write to PCI burst write
•Delayed transaction
•PCI parity checking and generation support
IDE bus master interface
The system board incorporates a PCI-to-IDE interface that complies with the AT Attachment Interface with Extensions.
The bus master for the IDE interface is integrated into the I/O hub of the
chip set. The chip set is PCI 2.2 compliant. It connects directly to the PCI bus and is designed to allow concurrent operations on the PCI bus and IDE bus. The chip set is capable of supporting PIO mode 0–4 devices and IDE DMA mode 0–3 devices. Ultra DMA 66 transfers up to 66 Mbps using an ATA 66 cable.
The IDE devices receive their power through a four-position power cable containing +5 V dc, +12 V dc, and ground voltage. As devices are added to the IDE interface, designate one device as the master, or primary, device and another as the slave, or subordinate, device. These designations are determined by switches or jumpers on each device. There are two IDE ports, one designated Primary and the other Secondary, allowing for up to four devices to be attached. The total number of physical IDE devices is determined by available space on the system board.
For the IDE interface, no resource assignments are given in the system memory or the direct memory access (DMA) channels. For information on the resource assignments, see “Input/output address map” on page 48 and “Appendix C. IRQ and DMA channel assignments,” on page 53.
For information on the connector pin assignments, see “IDE connectors” on page 42.
USB interface
Universal Serial Bus (USB) technology is a standard feature of your personal computer. The system board provides the USB interface with two connectors integrated into the chip set. A USB-enabled device can attach to a connector and, if that device is a hub, multiple peripheral devices can attach to the hub and be used by the system. The USB connectors use Plug and Play technology for installed devices. The speed of the USB is up to 12 MBps with a maximum of 127 peripheral devices. The USB is compliant with Universal Host Controller Interface Guide 1.0.
Features of USB technology include:
•Plug and Play devices
•Concurrent operation of multiple devices
•Suitability for different device bandwidths
Chapter 2. System board features 7
•Support for up to five-meter cable length from host to hub or hub to hub
•Guaranteed bandwidth and low latencies appropriate for specific devices
•Wide range of packet sizes
•Limited power to hubs
For information on the connector pin assignment for the USB interface, see “USB port connectors” on page 44.
Video Subsystem
The PC 300GL personal computer types 6563, 6564, and 6574 ad PC 300PL personal computer type 6565 come with one of the following graphic solutions:
1.S3 Savage4 Accelerated Graphics Port (AGP) 4X adapter with 8 MB 125 MHz SDRAM and a 15-pin VGA connector
2.S3 Savage4 Extreme AGP4X adapter with 16 MB 166 MHz SGRAM, a DVI-connector, and a 15-pin VGA converter.
The Savage4 graphics accelerator supports the following features:
•128-bit 2D graphics engine
•High-performance 2D/3D video accelerator
•3D rendering
•Motion video architecture
•High-speed memory bus
•Flat-panel monitor support
•ACPI and PCI power management
•PCI 2.2 bus support, including bus mastering
•300 MHz RAMDAC with gamma correction
•Serial bus and flash ROM support
•Hardware and BIOS support for VESA timing and DDC monitor communications
•2.5 V core with 3.3V/5V tolerant I/O
3.S3 Diamond AGP 4X adapter with 32 MB 143 MHz SDRAM with a DVI-I connector and, on some models, TV outlet on a daughter card.
The S3 Diamond graphics accelerator supports the following features:
•128-bit 3D graphics engine
•Two texture-mapped, lit pixels-per-clock cycle
•Single-pass multi-texturing
•32-bit Z/stencil buffer
•Anti-aliasing: full scene, order independent
•Up to 2048 x 1536 resolution
•30 frames per second (fps) full screen DVD playback
•National Television Systems Committee (NTSC) digital output (optional)
•Phase Alternate Line (PAL) digital output (optional)
•DVI-I interface
•Bidirectional Media Port and CCIR-656 video capture port (optional)
8 PC 300 GL and 300 PL
The integrated video subsystem supports all video graphics array (VGA) modes and is compliant with super video graphics array (SVGA) modes and Video Electronics Standards Association (VESA) 1.2. Some enhanced features include:
•Integrated video subsystem on chip, including 2D, 3D, and video port
•66 MHz AGP system bus interface with 2X and 4X
•Sideband signaling (some models only)
•Command list bus mastering support for fast 2D and 3D performance
•64-bit, 125 MHz SDRAM or 166 MHz SGRAM interface
•Plug and Play support
•4 MB dynamic display cache memory
•Advanced Power Management (APM) support
•Color space conversion
•Hardware scaling
The integrated graphics memory controller subsystem complys with the VESA Display Data Channel (DDC) 1.1 standard and uses DDC1 and DDC2B to determine optimal values during automatic minor detection.
The video subsystem has the following resource assignments.
Table 2. Video subsystem resources
Resource |
Assignment |
|
|
ROM |
Hex C0000-C7FFF (32KB) |
|
|
RAM |
Hex A0000-BFFFF (standard VGA frame buffer) |
|
|
I/O |
VGA, sequencer, CRT controller, graphics controller, attribute, RAMDAC, |
|
extended sequencer, extended CRTC registers |
|
|
IRQ |
PCI interrupt 1 (enabled by default in the Configuration/Setup Utility |
|
program. Normally assigned to IRQ 0B when nothing else is installed in |
|
the system. 3D systems use this interrupt.) |
|
|
DMA |
None, N/A for AGP bus |
|
|
For further information on resource assignments, see “Appendix B. System address maps,” on page 47 and “Appendix C. IRQ and DMA channel assignments,” on page 53.
Chapter 2. System board features 9
The PC 300GL personal computer types 6563, 6564, and 6574 and the PC 300PL type 6565 support the following video subsystem modes.
Table 3. Supported VGA video modes
Mode |
Display |
|
|
Buffer |
Dot |
Sweep |
Refresh |
|
Screen resolution |
Colors |
clock |
rate |
rate |
||||
(Hex) |
mode |
start (hex) |
||||||
|
|
(MHz) |
(kHz) |
(Hz) |
||||
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
00 |
Text |
40 x 25 characters |
2 |
B8000 |
28.322 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
01 |
Text |
40 x 25 characters |
16 |
B8000 |
28.322 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
02 |
Text |
80 x 25 characters |
Black/white |
B8000 |
28.322 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
03 |
Text |
80 x 25 characters |
16 |
B8000 |
28.322 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
04 |
Graphics |
320 x 200 pixels |
4 |
B8000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
05 |
Graphics |
320 x 200 pixels |
4 |
B8000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
06 |
Text |
640 x 200 pixels |
2 |
B8000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
07 |
Text |
80 x 25 characters |
Mono |
B8000 |
28.322 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
0D |
Graphics |
320 x 200 pixels |
16 |
A0000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
0E |
Graphics |
640 x 200 pixels |
16 |
A0000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
0F |
Graphics |
640 x 350 pixels |
Mono |
A0000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
10 |
Graphics |
640 x 350 pixels |
16 |
A0000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
|
11 |
Graphics |
640 x 480 pixels |
2 |
A0000 |
25.175 |
31.5 |
60 |
|
|
|
|
|
|
|
|
|
|
12 |
Graphics |
640 x 480 pixels |
16 |
A0000 |
25.175 |
31.5 |
60 |
|
|
|
|
|
|
|
|
|
|
13 |
Graphics |
320 x 200 pixels |
256 |
A0000 |
25.175 |
31.5 |
70 |
|
|
|
|
|
|
|
|
|
The video subsystem provides a 15-pin monitor connector on the system board. On some models, an optional 24-pin DVI-I monitor connector is provided on the AGP board. For information on monitor connector pin assignments see “Appendix A. Connector pin assignments,” on page 33 for SVGA and DVI.
Audio Subsystem
PC 300GL and PC 300PL personal computers come with an integrated audio controller. These models, which are capable of playing and recording sounds, support SoundBlaster, Adlib, and Microsoft Windows Sound System applications.
The device drivers for the preinstalled audio adapter are on the hard disk. The device drivers are also available on the Device Drivers and Diagnostics CD provided with models that come with preinstalled software.
If you connect an optional device to the audio adapter, follow the instructions provided by the manufacturer.
Note: Additional device drivers might be required. If necessary, contact the manufacturer for information on these device drivers.
The following connectors are available on the audio adapter or integrated audio controller:
•Line Out port for connecting powered speakers or headphones. You must connect a set of speakers to the Line Out port to hear audio from the adapter.
10 PC 300 GL and 300 PL
These speakers must be powered with a built in amplifier. In general, any powered speakers designed for use with personal computers can be used with the audio adapter. These speakers are available with a wide range of features and power outputs.
•Line In port for connecting musical devices, such as a portable CD-ROM player or stereo.
•Microphone for connecting a microphone.
Integrated peripheral controller
Control of the integrated input/output (I/O) and diskette drive controllers is provided by a single module, the integrated peripheral controller (SMC FDC 87B813). This module, which supports Plug and Play technology, controls the following features:
•Diskette drive interface
•Serial port
•Parallel port
•Keyboard and mouse ports
Diskette Drive Interface
PC 300GL and PC 300PL personal computers have four drive bays for installing internal devices. The following is a list of devices that the diskette drive subsystem supports:
•1.44 MB, 3.5 inch diskette drive
•1.44 MB, 3.5 inch, 3-mode drive for Japan (no BIOS support for 3-mode drive)
•1.2 MB, 5.25 inch diskette
•1 Mbps, 500 Kbps, or 250 Kbps internal tape drive
One connector is provided on the system board for diskette drive support. For information on the connector pin assignments, see “Diskette drive connector” on page 43.
Serial ports
Two universal asynchronous receiver/transmitter (UART) serial ports are integrated into the system board. The two serial ports include 16-byte data, first-in first-out (FIFO) buffers and have programmable baud rate generators. The serial ports are NS16450 and PC16550A compatible.
For information on the connector pin assignments, see “Serial port connector” on page 45.
Note: Current loop interface is not supported.
Chapter 2. System board features 11
The following figure shows the serial port assignments in the configuration.
Table 4. Serial port assignments
Port assignment |
Address range (hex) |
IRQ level |
|
|
|
Serial 1 |
03F8–03FF |
IRQ4 |
|
|
|
Serial 2 |
02F8–02FF |
IRQ3 |
|
|
|
Serial 3 |
03E8–03FF |
IRQ4 |
|
|
|
Serial 4 |
O2E8–027F |
IRQ13 |
|
|
|
The default setting for the serial port is COM1.
Parallel port
Integrated in the system board is support for extended capabilities port (ECP), enhanced parallel port (EPP), and standard parallel port (SPP) modes. The modes of operation are selected through the Configuration/Setup Utility program with the default mode set to SPP.
The following figure shows the parallel port assignments used in the configuration.
Table 5. Parallel port assignments
Port assignment |
Address range (hex) |
IRQ level |
|
|
|
Parallel 1 |
03BC–03BE |
IRQ7 |
|
|
|
Parallel 2 |
0378–037F |
IRQ5 |
|
|
|
Parallel 3 |
0278–03FF |
IRQ5 |
|
|
|
The default setting for the parallel port is Parallel 1.
The system board has one connector for the parallel port. For information on the connector pin assignments, see “Parallel port connector” on page 46.
Keyboard and mouse ports
A general purpose 8-bit microcontroller, 8042AH compatible, controls the mouse and keyboard subsystem. The controller consists of 256 bytes of data memory and 2 KB of read-only memory (ROM).
The controller has two logical devices: one controls the keyboard and the other controls the mouse. The keyboard has two fixed I/O addresses, a fixed IRQ line, and can operate without the mouse. The mouse cannot operate without the keyboard because, although it has a fixed IRQ line, the mouse relies on the addresses of the keyboard for operation. For the keyboard and mouse interfaces, no resource assignments are given in the system memory addresses or DMA channels. For information on the resource assignments, see “Input/output address map” on page 48 and “Appendix C. IRQ and DMA channel assignments,” on page 53.
The system board has one connector for the keyboard port and one connector for the mouse port. For information on the connector pin assignments, see “Mouse and keyboard port connectors” on page 45.
12 PC 300 GL and 300 PL
Network connection
Some PC 300 GL and PC 300 PL models are equipped with an Ethernet or token-ring adapter that supports the Wake on LAN feature.
Features of the optional Wake on LAN Ethernet adapter are:
•Operates in shared 10BASE-T or 100BASE-TX environment
•Transmits and receives data at 10 Mbps or 100 Mbps
•Has an RJ-45 connector for LAN attachment
•Operates on symmetrical multiprocessing (SMP) environments
•Supports Wake on LAN
•Supports Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)
Features of the optional token-ring adapter are:
•Transmits and receives data at 4 Mbps or 16 Mbps
•Has RJ-45 and D-shell connectors for LAN attachment
•Supports Wake on LAN
•Supports Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)
The PC 300GL personal computer has a 3-pin header on the system board that provides the AUX5 (auxiliary 5 volts) and wake-up signal connections.
Real-time clock and CMOS
The real-time clock is low-power and provides a time-of-day clock and a calendar. An external battery source of 3 V dc maintains the settings.
The system uses 242 bytes of complementary metal-oxide semiconductor (CMOS) memory to store data. To erase or reset CMOS memory to the default, use the small rocker switch on the system board.
Note: Refer to the instructions in the PC 300PL and PC 300GL User Guide before attempting to reset CMOS.
To locate the battery and the rocker switches, see “Physical layout” on page 14.
Flash EEPROM
The system board uses two megabits (Mb) of flash electrically erasable programmable, read-only memory (EEPROM) to store the basic input/output system (BIOS), IBM logo, Configuration/Setup Utility, and Plug and Play data.
If necessary, you can update the EEPROM by downloading a stand-alone utility program available from the IBM Web site: http://www.ibm.com/pc.
Expansion adapters
Each PCI-expansion connector is a 32-bit slot. PCI-expansion connectors support the 32-bit, 5 V dc, local-bus signalling environment defined in PCI Local Bus Specification 2.2.
PC 300GL personal computer types 6563, 6564, and 6574 and PC 300PL personal computer type 6565 personal computers have three PCI slots to support the addition of adapters. For information on installing adapters, see the PC 300GL and PC 300PL User Guide.
Chapter 2. System board features 13
For information on the connector pin assignments, see “PCI connectors” on page 40.
Note: PC 300GL computers do not support ISA expansion adapters or the IBM PCMCIA adapter for PCI.
Physical layout
The system board might look slightly different from the one shown.
Note: A diagram of the system board, including switch and jumper settings, is attached to the underside of the computer cover.
14 PC 300 GL and 300 PL
Loading...