Size:
902.43 Kb
Download

CI5VGM Series

Full-Size Pentium All-in-one CPU Card

Version 1.0A

Industrial CPU Card

PC-Based Computer Boards for Industrial Automation

User’s Manual

Copyright Notice

This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any form, without prior consent of the original manufacturer.

The information in this document has been carefully checked and is believed to be accurate. However, the original manufacturer assumes no responsibility for any inaccuracies that may appear in this manual. In no event will the original manufacturer be liable for direct, indirect, special, exemplary, incidental, incidental or consequential damages resulting from any defect or omission in this manual, even if advised of possibility of such damages. The material contained herein is for informational purposes only.

Acknowledgments

Award is a registered trademark of Award Software International, Inc. Cyber 9520/25 is a trademark of Trident Technologies Inc.

IBM, PS/2 are trademarks of International Business Machines Corporation.

Intel and Pentium are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. MVP3 is a registered trademark of VIA Technologies Inc.

All other product names or trademarks are properties of their respective owners.

ii

CI5VGM User’s Manual

 

Contents

Contents

 

Chapter 1 Introduction.............................................

1

Checklist.....................................................................

3

Description .................................................................

3

Features ......................................................................

4

Specifications .............................................................

4

Intelligence .................................................................

7

Board Dimensions .....................................................

8

Chapter 2 Installations ...........................................

10

CPU Installation ......................................................

11

Memory Installation................................................

12

Jumpers on the CI5VGM .......................................

14

Connectors on the CI5VGM...................................

24

Watchdog Timer Configuration ............................

37

Chapter 3 BIOS Configuration..............................

38

Chapter 4 Audio Driver Installation Guide..........

65

Chapter 5 VGA Driver Installation Guide ...........

77

Chapter 6 System Monitor Utility .........................

97

Chapter 7 LANDesk Client Manager .................

105

Chapter 8 Ethernet Setup User’s Guide .............

113

Appendix.................................................................

126

A. I/O Port Address Map.....................................

127

B. Interrupt Request Lines (IRQ).......................

128

CI5VGM User’s Manual

iii

Chapter 1 Introduction

Below are additional information for LCD Panel Type Select and settings for newer CPUs

SW3: LCD Panel Type Select

1

2

3

4

TFT LCD Panel

 

 

 

 

 

ON

ON

ON

ON

640x480 –18

OFF

ON

ON

ON

800x600 –18

ON

OFF

ON

ON

1024x768 –18

OFF

OFF

ON

ON

1024x768 –18+18

ON

ON

OFF

ON

1280x1024 –18+18

1

2

3

4

DSTN LCD Panel

 

 

 

 

 

ON

ON

ON

OFF

640x480 –16

OFF

ON

ON

OFF

800x600 –16

ON

OFF

ON

OFF

1024x768 –16

OFF

OFF

ON

OFF

1024x768 –24

ON

ON

OFF

OFF

1280x1024 –24

Settings for New Cyrix/AMD CPUs

 

 

 

 

 

 

 

 

95MHz

63MHz

3.5x

MII-400

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(333MHz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on off off on off off off off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

3.5x

MII-433

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(350MHz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off off off on off off off off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

95MHz

63MHz

4x

MII-450

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(380MHz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on off off on on off on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

4x

MII-466

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(400MHz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off off off on on off on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

95MHz

63MHz

5x

K6-2/475

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

K6-3/475

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on off off on off on on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

5x

K6-2/500

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

K6-3/500

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off off off on off on on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CI5VGM User’s Manual

 

 

1

Chapter 1 Introduction

1

Introduction

This manual is designed to give you information on the CI5VGM CPU card. It is divided into the following sections:

Checklist .......................................................................................

3

Description....................................................................................

3

Features.........................................................................................

4

Specifications................................................................................

4

Intelligence ...................................................................................

7

Board Dimensions.........................................................................

8

The topics covered in this chapter are as follows:

Checklist

Description

Features

Specifications

Layout of Key Components and Dimensions

2

CI5VGM User’s Manual

Chapter 1 Introduction

Checklist

Please check that your package is complete and contains the items below. If you discover damaged or missing items, please contact your dealer.

The CI5VGM Industrial CPU Card

This User’s Manual

1 IDE Ribbon Cable

1 Floppy Ribbon Connector

2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a Mounting Bracket

1 Audio Output Ribbon Cable and EXTVGM Daughter Card Audio I/O Connector (supplied only if the CPU card has the audio capability)

1 Diskette Containing VIA PCI IDE Driver and Flash Memory Utility, VIA IRQ Routing Driver, VIA VxD Driver

2 Diskettes Containing Trident 9520/25 VGA Driver

2 Diskettes Containing Intel 82558B LAN Driver

5 Diskettes Containing YAMAHA 715 Audio Driver

1 Diskette Containing System Monitor Utility

1 Optional CD containing Intel LANDesk Client Manager

Description

The CI5VGM is a Pentium Industrial CPU card based on the VIA MVP3 chipset and is fully designed for harsh industrial environment. It features a Socket 7 processor connector that is compatible with Pentium-level processors from Intel, Cyrix, AMD and IDT. With three DIMM sockets on board, this card accommodates up to 384MB of system memory.

The CI5VGM comes with Winbond’s W83781D hardware monitoring device that monitors system and CPU temperature, system voltages, and CPU and chassis fan speeds to prevent system crashes by warning the user of adverse conditions. The power management feature provides power savings by slowing down the CPU clock, turning off the monitor screen and stopping the HDD spindle motor.

CI5VGM User’s Manual

3

Chapter 1 Introduction

Features

Socket 7, CPU Speed 90~550MHz

Bus Speed 60/66/75/83/95/100MHz

VIA MVP3 AGPset

Up to 384MB of system memory, ECC function supported

Trident 9520/25 AGP VGA chipset for LCD & CRT display

YAMAHA 715 Audio Chip

16 level programmable watchdog timer, from 0-30 seconds

High speed bi-directional SPP/ECP/EPP parallel port

ISA High Drive

2MB~72MB DiskOnChip support

Hardware Monitoring

Win95 shut-off, Modem ring-on via ATX power

10/100M Base-T Ethernet interface, IEEE 802.3 compliance specification

Port 80 display LED

COM2 supports RS232/433/485

Specifications

Processor Socket: Socket 7 connector

Processor:

Intel Pentium 120/133/150/166/200

Intel Pentium MMX (P55C) 166/200/233

Cyrix 6x86/6x86L P150+/P166+/P200+

Cyrix 6x86MX PR166/PR200/PR233/PR266

Cyrix 6x86MII PR266/PR300/PR333/PR366

AMD K5 PR166

AMD K6 166/200/233/266/300

AMD K6-2/300/333/350/366/380/400/450

IDT WinChip C6 180/200/225MHz

IDT WinChip2-3D 200/225/266MHz

Chipset: VIA MVP3 AGPset with PCI EIDE and RTC built-in

Secondary Cache: 1 MB

4

CI5VGM User’s Manual

Chapter 1 Introduction

Memory Sockets:

Three 168-pin DIMM sockets

Memory types: SDRAM (Synchronous DRAM)

DIMMs: EDO DRAM or SDRAM (Synchronous DRAM) DIMM Size: 8MB, 16MB, 32MB, 64MB, 128MB

BIOS: Y2K compliant Award BIOS, PnP support

FLASH EEPROM (256KB) for BIOS update

ISA Plug and Play (PnP) extension

Power management

DMI BIOS Support:

Desktop Management Interface (DMI) allows users to download system hardware-level information such as CPU type, CPU speed, internal/external frequencies and memory size.

Multi I/O: Winbond W83877TF

Parallel Port: One high-speed parallel port, SPP/EPP/ECP mode

Serial Port: Two 16550 UART compatible ports with COM1 as RS232 and COM2 jumper configurable as RS232/422/485

Enhanced IDE: Two Bus Mastering EIDE mode, up to 4 devices, Two EIDE interfaces for up to four devices, support PIO Mode 3/4 or Ultra DMA/33 IDE Hard Disk, LS-120 and ATAPI CD-ROM.

FDD Interface: Two floppy drives (360KB, 720KB, 1.2MB, 1.44MB, 2.88MB)

AGP bus CRT/LCD: Trident 9520/25 chipset

Embedded 2MB/2.5MB (9520/9525) SDRAM display memory

Simultaneous CRT & LCD display

LCD panel supports DSTN/TFT

1600x1200x256 colors CRT resolution

Up to 1280x1024x64K colors resolution for color active matrix TFT panels (12, 18, and 24bit analog) or (12+12), (18+18) double pixel/CLK interface

USB Interface: Two USB pin-header connectors, compliant with USB Specification Rev. 1.0

CI5VGM User’s Manual

5

Chapter 1 Introduction

Onboard Audio (optional): The onboard audio consists of a YAMAHA YMF715-S (OPL3-SA3) single audio chip that integrates OPL3 and its DAC, 16bit Sigma-delta CODEC, MPU401 MIDI interface, joystick with timer, and a 3D enhanced controller including all the analog components which is suitable for multimedia application.

DiskOnChip: The M-Systems flask disk supports system boot and storage capacity from 2MB to 72MB.

Watchdog Timer: 16-level, programmable

I/O port 0443H to enable watchdog.

I/O port 0441H to disable watchdog.

Time-out timing select 0/2/4/6/8/10/12/14/16/18/20/22/ 24/26/28/30 seconds (+/-20%).

PCI Bus Ethernet Interface: Intel 82558B

PCI local bus Ethernet controller

IEEE802.3u auto-negotiation for automatic speed selection

10/100Mbps operation in a single port PCI bus master architecture

Wake On LAN function support on board

Green Function: Power management via BIOS, activated through mouse/keyboard movement

Keyboard and Mouse Connectors: PS/2 type mini-DIN that supports PC/AT; supports a 5-pin external keyboard connector

IrDA Interface: Pin-header connector for the optional IrDA external connector

PICMG Compliance: Fully compliant to PICMG standards

Environmental and Mechanical:

AT Power Supply: Max. 15A @+5V

ATX Power Supply: Min 1A @+5VSB, Max15A@+5V

Temperature: 0° C to 60° C

Humidity: 5% to 95%

Dimensions: 338mm x 122mm

6

CI5VGM User’s Manual

Chapter 1 Introduction

Intelligence

Temperature Monitoring and Alert: A sensor for the CPU temperature on the CI5VGM monitors the CPU temperature and alerts the user through the speaker or buzzer when temperature exceeds the safe heat level.

Windows 95 shut-off: Allows shut-off control from within Windows 95 and through an ATX power supply.

Modem ring-on: Allows system powering on through an external modem and through an ATX power supply.

Year 2000 Compliant BIOS: The onboard Award BIOS is Year 2000 Compliant and will pass software applications that have the tendency to invoke INT1AH function 04H such as year2000.exe utility released by NSTL.

CI5VGM User’s Manual

7

Chapter 1 Introduction

Board Dimensions

8

CI5VGM User’s Manual

Chapter 1 Introduction

This page is intentionally left blank .

CI5VGM User’s Manual

9

Chapter 2 Installations

2

Installations

This chapter provides information on how to use the jumpers and connectors on the CI5VGM in order to set up a workable system. The topics covered are:

CPU Installation..........................................................................

11

Memory Installation....................................................................

12

Jumpers on the CI5VGM............................................................

14

Connectors on the CI5VGM .......................................................

24

Watchdog Timer Configuration..................................................

37

10

CI5VGM User’s Manual

Chapter 2 Installations

CPU Installation

The CI5VGM Industrial CPU Card supports a ZIF processor socket for Pentium-level processors.

Unlike PGA sockets, ZIF (Zero Insertion Force) sockets come with a lever to secure the processor. Make sure the notch on the corner of the CPU corresponds with the notch on the inside of the socket.

After you have installed the processor into the ZIF socket, check if the jumpers for the CPU type and speed are correct.

NOTE: Ensure that the CPU heat sink and the CPU top surface are in total contact to avoid CPU overheating problem that would cause your system to hang or be unstable.

CI5VGM User’s Manual

11

Chapter 2 Installations

Memory Installation

The CI5VGM Industrial CPU Card supports three 168-pin DIMM sockets for a maximum total memory of 384MB. The memory modules can come in sizes of 16MB, 32MB, 64MB, 128MB in EDO DRAM or SDRAM type.

In populating the DIMM sockets, DIMM1, DIMM2 or DIMM3 can be populated first. Refer to the following table on how to configure the memory.

NOTE: You must install memory modules of the same type, either all SDRAM or all EDO DRAM.

168Pin DIMM (3.3V) - SDRAM or EDO DRAM

 

(DIMM3)

(DIMM2)

(DIMM1)

Total Memory

 

 

 

 

8MB

-----

-----

8MB

 

 

16MB

-----

-----

16MB

 

 

32MB

-----

-----

32MB

 

 

64MB

-----

-----

64MB

 

 

128MB

-----

-----

128MB

 

 

8MB

8MB

-----

16MB

 

 

16MB

8MB

-----

24MB

 

 

32MB

8MB

-----

40MB

 

 

64MB

8MB

-----

72MB

 

 

128MB

8MB

-----

136MB

 

 

8MB

8MB

8MB

24MB

 

 

16MB

8MB

8MB

32MB

 

 

32MB

8MB

8MB

48MB

 

 

64MB

8MB

8MB

80MB

 

 

128MB

8MB

8MB

144MB

 

 

16MB

16MB

-----

32MB

 

 

32MB

16MB

-----

48MB

 

 

64MB

16MB

-----

80MB

 

 

128MB

16MB

-----

144MB

 

 

16MB

16MB

8MB

40MB

 

 

32MB

16MB

8MB

56MB

 

 

64MB

16MB

8MB

88MB

 

 

128MB

16MB

8MB

152MB

 

 

 

 

 

 

 

12

 

 

 

CI5VGM User’s Manual

Chapter 2 Installations

168Pin DIMM (3.3V) - SDRAM or EDO DRAM (continued)

(DIMM3)

(DIMM2)

(DIMM1)

Total Memory

16MB

16MB

16MB

48MB

32MB

16MB

16MB

64MB

64MB

16MB

16MB

96MB

128MB

16MB

16MB

160MB

32MB

32MB

-----

64MB

64MB

32MB

-----

96MB

128MB

32MB

-----

160MB

32MB

32MB

8MB

72MB

64MB

32MB

8MB

104MB

128MB

32MB

8MB

168MB

32MB

32MB

16MB

80MB

64MB

32MB

16MB

112MB

128MB

32MB

16MB

176MB

32MB

32MB

32MB

96MB

64MB

32MB

32MB

128MB

128MB

32MB

32MB

192MB

64MB

64MB

-----

128MB

128MB

64MB

-----

192MB

64MB

64MB

8MB

136MB

128MB

64MB

8MB

200MB

64MB

64MB

16MB

144MB

128MB

64MB

16MB

208MB

64MB

64MB

32MB

160MB

128MB

64MB

32MB

224MB

64MB

64MB

64MB

192MB

128MB

64MB

64MB

256MB

128MB

128MB

128MB

384MB

CI5VGM User’s Manual

13

Chapter 2 Installations

Jumpers on the CI5VGM

The jumpers on the CI5VGM allows you to configure your CPU card according to the needs of your applications. If you have doubts about the best jumper configuration for your needs, contact your dealer or sales representative. The following table lists the connectors on CI5VGM and their respective functions.

Jumper Locations on the CI5VGM ....................................

15

SW1(1-8): CPU Frequency Selector ..................................

16

JP2: SDRAM Operating Frequency ...................................

19

SW2(1-4): CPU Voltage Selector ......................................

19

JP3: LCD Power Setting.....................................................

21

JP4: CRT/LCD Display Selection ......................................

21

JP6: DiskOnChip BIOS Expansion Address Select ...........

22

J11: RS232/422/485 (COM2) Selection.............................

22

J24: Clear CMOS Content..................................................

23

W1: Power Supply Select..................................................

23

14

CI5VGM User’s Manual

Chapter 2 Installations

Jumper Locations on the CI5VGM

CI5VGM User’s Manual

15

Chapter 2 Installations

SW1(1-8): CPU Frequency Selector

For Intel Pentium, IDT WinChip 2-3D / C6

 

SW1

 

 

CPU

AGP

Multiplier

CPU FREQ.

 

 

 

 

 

 

Clock

Clock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

60MHz

60MHz

1.5x

P54C-90

 

on on on off off off off on

 

 

 

 

 

 

 

 

66MHz

66MHz

1.5x

P54C-100

 

 

 

 

 

off on on off off

off off on

 

 

 

 

 

 

 

 

60MHz

60MHz

2x

P54C-120

 

 

 

 

 

on on on off on off off on

 

 

 

 

 

 

 

 

 

66MHz

66MHz

2x

P54C-133

 

 

 

 

 

off on on off on off off on

 

 

 

 

 

 

 

 

60MHz

60MHz

2.5x

P54C-150

 

 

 

 

 

on on on off on on off on

 

 

 

 

 

 

 

 

 

66MHz

66MHz

2.5x

P54C/P55C-16

 

 

 

 

 

 

 

 

6

 

off on on off on on off on

 

 

 

 

 

 

 

 

60MHz

60MHz

3x

C6-180

 

 

 

 

 

on on on off off on off on

 

 

 

 

 

 

 

 

 

 

 

 

P54C/P55C-200

 

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

3x

WinChip 2-3D

 

off on on off off

on off on

 

 

 

 

/ C6-200

 

 

 

 

66MHz

66MHz

3.5x

P55C-233

 

 

 

 

 

off on on off off off off on

 

 

 

 

 

 

 

 

 

75MHz

75MHz

3x

WinChip 2-3D

 

 

 

 

 

 

 

 

/ C6-225

 

off off on off off on off on

 

 

 

 

 

 

 

 

66MHz

66MHz

4x

WinChip 2-3D

 

 

 

 

 

 

 

 

266

 

off on on off on off on on

 

 

 

16

CI5VGM User’s Manual

 

 

 

 

 

 

 

Chapter 2 Installations

 

 

For Cyrix 6x86, 6x86L, 6x86MX. MII CPU

 

 

 

 

 

 

 

 

 

 

 

 

SW1

 

 

CPU

AGP

Multiplier

CPU FREQ.

 

 

 

 

 

Clock

Clock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

2x

P166+

 

 

 

 

 

 

(133MHz)

 

 

 

off on on off on

off off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

75MHz

75MHz

2x

P200+

 

 

 

 

 

 

 

 

 

 

 

 

(150MHz)

 

 

 

off off on off on

off off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

2.5x

PR200

 

 

 

 

 

 

 

 

 

 

 

 

(166MHz)

 

 

 

off on on off on

on off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

3x

PR233

 

 

 

 

 

 

 

 

 

 

 

 

(200MHz)

 

 

 

off on on off off on off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

3.5x

PR266

 

 

 

 

 

 

 

 

 

 

 

 

(233MHz)

 

 

 

off on on off off off off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

75MHz

75MHz

2.5x

PR233

 

 

 

 

 

 

 

 

 

 

 

 

(187.5MHz)

 

 

off off on off on

on off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

83MHz

66MHz

2.5x

PR266

 

 

 

 

 

 

 

 

 

 

 

 

(208MHz)

 

 

off on off off on

on off off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

83MHz

66MHz

3x

PR333

 

 

 

 

 

 

 

 

 

 

 

 

(250MHz)

 

 

off on off off off

on off off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

2.5x

PR333

 

 

 

 

 

 

 

 

 

 

 

 

(250MHz)

 

 

off off off on on

on off off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

3x

PR366

 

 

 

 

 

 

 

 

 

 

 

 

(300MHz)

 

 

off off off on off

on off off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CI5VGM User’s Manual

17

Chapter 2 Installations

For AMD K5, K6, K6-2 CPU

 

 

SW1

 

 

 

CPU

AGP

Multiplier

CPU FREQ.

 

 

 

 

 

 

 

 

 

 

Clock

Clock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

60MHz

60MHz

1.5x

PR90

 

 

 

 

 

 

 

 

 

 

 

on on on off off off off on

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

1.5x

PR100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off on on off off

off off on

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

2x

PR133

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off on on off on off off on

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

2.5x

PR166 /

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

K6-166

 

 

off on on off on on off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

3x

K6-200

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off on on off off on off on

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

3.5x

K6-233

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off on on off off off off on

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

4x

K6-266

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off on on off on

off on on

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

4.5x

K6-300

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off on on off on on on on

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

3x

K6-2/300

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off off off on off on off off

 

 

 

 

 

 

 

 

 

 

95MHz

63MHz

3.5x

K6-2/333

 

 

 

 

 

 

 

 

on off off on off off off off

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

3.5x

K6-2/350

 

 

 

 

 

 

 

 

off off off on off off off off

 

 

 

 

 

 

 

 

 

 

 

 

66MHz

66MHz

5.5x

K6-2/366

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off on on off off off on on

 

 

 

 

 

 

 

 

 

 

 

95MHz

63MHz

4x

K6-2/380

 

 

 

 

 

 

 

 

on off off on on off on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

 

 

 

 

 

CI5VGM User’s Manual

 

 

 

 

 

 

 

 

 

 

Chapter 2

Installations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

 

4x

 

 

K6-2/400

 

 

off off off on on off on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100MHz

66MHz

 

4.5x

 

 

K6-2/450

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off off off on on on on off

 

 

 

 

 

 

 

 

 

JP2: SDRAM Operating Frequency

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JP2

 

 

SDRAM Frequency

 

 

 

 

 

 

 

 

 

 

 

 

 

pin 1-2

short

Run CPU Clock

 

 

 

 

 

pin 2-3

short

Run AGP Clock

 

 

NOTE: Set the SDRAM Frequency to Run CPU Clock only when the CPU clock is 100MHz and the DIMM module onboard meets PC-100 specifications.

SW2(1-4): CPU Voltage Selector

For Single Voltage CPU:

Intel P54C, Cyrix 6x86, AMD K5, IDT WinChip C6

 

SW2

VIO

VCORE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.5V

3.5V

 

on on on on

For Dual Voltage CPU:

Intel P55C, Cyrix 6x86L/MX/MII, AMD K6/K6-2, IDT WinChip 2-3D

SW2

VIO

VCORE

CPU

 

 

 

 

 

 

 

 

 

3.3V

3.5V

WinChip 2-3D

 

(0.35 )

on on on on

 

 

 

 

 

 

3.3V

3.4V

 

off on on on

 

 

 

 

3.3V

3.3V

 

on off on on

 

 

 

Remarks: 0.35 and 0.25 refers to CPU manufacturing process.

CI5VGM User’s Manual

19

Chapter 2 Installations

For Dual Voltage CPU:

Intel P55C, Cyrix 6x86L/MX/MII, AMD K6/K6-2, IDT WinChip 2-3D

 

SW2

 

VIO

VCORE

CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

3.2V

K6-233

 

 

 

 

(0.35

)

 

 

off off on

on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

3.1V

 

 

 

 

on on off on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

3.0V

 

 

 

 

off on off

on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

2.9V

K6-166/200

 

 

 

 

6x86MX

 

 

on off off

on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WinChip 2-3D

 

 

 

 

3.3V

2.8V

(0.35

)

 

 

 

 

P55C

 

 

 

 

 

 

 

 

 

 

off off off

on

 

 

6x86L

 

 

 

 

3.3V

2.7V

 

 

 

 

on on on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

2.6V

 

 

 

 

off on on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

2.5V

 

 

 

 

on off on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

2.4V

 

 

 

 

off off on off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

2.3V

 

 

 

 

on on off off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20

 

 

 

 

CI5VGM User’s Manual

Chapter 2 Installations

For Dual Voltage CPU:

Intel P55C, Cyrix 6x86L/MX/MII, AMD K6/K6-2

SW2

 

VIO

VCORE

CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

2.2V

K6, K6-2

 

 

(0.25 )

off on off off

 

 

 

 

 

 

 

 

 

 

 

 

3.3V

2.1V

 

on off off

off

 

 

 

 

 

 

 

 

 

 

3.3V

2.0V

 

off off off

off

 

 

 

 

 

 

 

 

JP3: LCD Power Setting

The CI5VGM XGA interface supports 5V and 3.3V LCD displays. Use JP3 to change between 5V (default) and 3.3V panel video signal level.

 

3.3V Setting

 

 

5V Setting

 

 

2

4

6

 

2

4

6

 

 

1

3

5

 

1

3

5

 

JP4: CRT/LCD Display Selection

The JP4 jumper is used to toggle between CRT and LCD display.

 

JP4

 

 

Function

 

 

JP4

 

 

Function

 

 

 

 

CRT Display

 

 

 

 

LCD Display

 

 

short

 

 

 

 

 

open

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CI5VGM User’s Manual

21

Chapter 2 Installations

JP6: DiskOnChip BIOS Expansion Address Select

 

JP6

 

 

 

Address

 

 

JP6

 

 

 

Address

 

 

 

 

 

 

D0000-D7FFF

 

 

 

 

 

 

D8000-DFFFF

 

 

 

 

 

 

1

2

3

 

 

(default)

 

1

2

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J11: RS232/422/485 (COM2) Selection

COM1 is fixed for RS-232 use only.

COM2 is selectable for RS232, RS-422 and RS-485.

The following table describes the jumper settings of this connector.

COM2

 

RS-232

 

RS-422

 

RS-485

Function

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-2

 

 

 

1-2

 

 

 

 

 

 

 

 

 

 

3-4

 

 

 

3-4

 

 

Jumper

 

 

 

 

 

 

 

5-6

 

 

 

5-6

 

 

Setting

 

 

 

 

 

 

 

7-8

 

 

 

7-8

 

 

(pin closed)

 

 

all

 

11-12

 

 

9-10

 

 

 

jumpers

15-16

11-12

 

 

 

open

17-18

13-14

 

 

 

 

 

 

19-20

15-16

 

 

 

 

 

 

23-24

17-18

 

 

 

 

 

 

 

 

 

 

 

 

19-20

 

 

 

 

 

 

 

 

 

 

 

 

21-22

 

 

 

 

 

 

 

 

 

 

 

 

23-24

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

1

 

2

 

1

 

 

2

 

 

3

4

 

3

 

4

 

3

 

 

4

 

 

5

6

 

5

 

6

 

5

 

 

6

 

 

7

8

 

7

 

8

 

7

 

 

8

Jumper

9

10

9

 

10

9

 

 

10

11

12

11

 

12

11

 

 

12

Illustration

13

14

13

 

14

13

 

 

14

15

16

15

 

16

15

 

 

16

 

17

18

17

 

18

17

 

 

18

 

19

20

19

 

20

19

 

 

20

 

21

22

21

 

22

21

 

 

22

 

23

24

23

 

24

23

 

 

24

 

 

 

J11

 

 

 

J11

 

 

 

J11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

CI5VGM User’s Manual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chapter 2 Installations

J24: Clear CMOS Content

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J24

 

 

 

 

 

Setting

 

 

 

 

 

 

Function

 

 

 

 

 

 

 

 

 

 

 

Pin 2-3

 

 

Clear CMOS Content

 

 

1

2

3

 

 

 

Short/Closed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 1-2

 

 

 

Normal Operation

 

 

1

2

3

 

 

 

Short/Closed

 

 

 

 

(default)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

W1: Power Supply Select

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

W1

 

 

Function

 

 

 

W1

 

 

 

 

Function

 

 

 

 

 

 

 

 

ATX Power

 

 

 

 

 

 

 

 

AT Power

 

 

 

short

 

 

 

 

 

 

 

 

 

open

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: Failure to set W1 correctly may cause the system not to boot or the CMOS content to be erased.

CI5VGM User’s Manual

23

Chapter 2 Installations

Connectors on the CI5VGM

The connectors on the CI5VGM allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on CI5VGM and their respective functions.

Connector Locations on the CI5VGM................................

25

J1: Floppy Drive Connector ...............................................

26

J2: Parallel Port Connector.................................................

26

IDE1, IDE2: EIDE Connectors ..........................................

27

J3: External ATX Power Connector...................................

28

J18: AT Power Connector ..................................................

28

J4: Audio I/O Connector (optional)....................................

28

J5: USB Connector.............................................................

29

J6: COM1 Serial Port .........................................................

30

J7: COM2 Serial Port .........................................................

30

J8: Front Bezel Connector..................................................

31

J9: LCD Panel Connector...................................................

33

J14: Chassis Fan Power Connector ....................................

34

J22, J23: CPU Fan Power Connectors................................

34

J15: IrDA Connector .........................................................

34

J16: External Keyboard Connector ....................................

34

J17: External Mouse Connector .........................................

35

J19: PS/2 Keyboard Connector ..........................................

35

J20: PS/2 Mouse Connector ...............................................

35

J21: VGA CRT Connector .................................................

36

J25: RJ45 Connector ..........................................................

36

24

CI5VGM User’s Manual

Chapter 2 Installations

Connector Locations on the CI5VGM

CI5VGM User’s Manual

25

Chapter 2 Installations

J1: Floppy Drive Connector

J1 is a 34-pin header and will support up to 2.88MB floppy drives.

 

 

Signal Name

 

 

Pin #

 

 

Pin #

 

 

Signal Name

 

 

 

Ground

 

1

 

2

 

 

RM/LC

 

 

 

Ground

 

3

 

4

 

 

No connect

 

 

 

Ground

 

5

 

6

 

 

No connect

 

 

 

Ground

 

7

 

8

 

 

Index

 

 

 

Ground

 

9

 

10

 

 

Motor enable 0

 

 

 

Ground

 

11

 

12

 

 

Drive select 1

 

 

 

Ground

 

13

 

14

 

 

Drive select 0

 

 

 

Ground

 

15

 

16

 

 

Motor enable 1

 

 

 

Ground

 

17

 

18

 

 

Direction

 

 

 

Ground

 

19

 

20

 

 

Step

 

 

 

Ground

 

21

 

22

 

 

Write data

 

 

 

Ground

 

23

 

24

 

 

Write gate

 

 

 

Ground

 

25

 

26

 

 

Track 00

 

J1

 

Ground

 

27

 

28

 

 

Write protect

 

 

Ground

 

29

 

30

 

 

Read data

 

 

 

 

 

 

 

 

 

 

Ground

 

31

 

32

 

 

Side 1 select

 

 

 

Ground

 

33

 

34

 

 

Diskette change

 

J2: Parallel Port Connector

 

 

Signal Name

 

 

Pin #

 

 

Pin #

 

 

Signal Name

 

 

 

 

Line printer strobe

 

1

 

14

 

 

AutoFeed

 

 

 

PD0, parallel data 0

 

2

 

15

 

 

Error

 

 

 

PD1, parallel data 1

 

3

 

16

 

 

Initialize

 

 

 

PD2, parallel data 2

 

4

 

17

 

 

Select

 

 

 

PD3, parallel data 3

 

5

 

18

 

 

Ground

 

 

 

PD4, parallel data 4

 

6

 

19

 

 

Ground

 

 

 

PD5, parallel data 5

 

7

 

20

 

 

Ground

 

 

 

PD6, parallel data 6

 

8

 

21

 

 

Ground

 

 

 

PD7, parallel data 7

 

9

 

22

 

 

Ground

 

 

 

ACK, acknowledge

 

10

 

23

 

 

Ground

 

 

 

Busy

 

11

 

24

 

 

Ground

 

J2

 

Paper empty

 

12

 

25

 

 

Ground

 

 

 

Select

 

13

 

 

N/A

 

 

N/A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26

 

 

 

 

 

 

 

CI5VGM User’s Manual

Chapter 2 Installations

IDE1, IDE2: EIDE Connectors

IDE1

IDE2

IDE1: Primary IDE Connector

 

Signal Name

 

 

Pin #

 

 

Pin #

 

 

Signal Name

 

 

Reset IDE

 

 

1

 

 

2

 

 

Ground

 

 

 

Host data 7

 

3

 

4

 

 

Host data 8

 

 

Host data 6

 

5

 

6

 

 

Host data 9

 

 

Host data 5

 

7

 

8

 

 

Host data 10

 

 

Host data 4

 

9

 

10

 

 

Host data 11

 

 

Host data 3

 

11

 

12

 

 

Host data

12

 

 

Host data 2

 

13

 

14

 

 

Host data

13

 

 

Host data 1

 

15

 

16

 

 

Host data

14

 

 

Host data 0

 

17

 

18

 

 

Host data

15

 

 

Ground

 

19

 

20

 

 

Key

 

 

 

DRQ0

 

21

 

22

 

 

Ground

 

 

 

Host IOW

 

23

 

24

 

 

Ground

 

 

 

Host IOR

 

25

 

26

 

 

Ground

 

 

 

IOCHRDY

 

27

 

28

 

 

Host ALE

 

 

DACK0

 

29

 

30

 

 

Ground

 

 

 

IRQ14

 

31

 

32

 

 

No connect

 

 

Address 1

 

33

 

34

 

 

No connect

 

 

Address 0

 

35

 

36

 

 

Address

2

 

 

Chip select 0

 

37

 

38

 

 

Chip select 1

 

 

Activity

 

39

 

40

 

 

Ground

 

 

IDE2: Secondary IDE Connector

 

 

 

 

 

 

Signal Name

 

 

Pin #

 

 

Pin #

 

 

Signal Name

 

 

Reset IDE

 

 

1

 

 

2

 

 

Ground

 

 

 

Host data 7

 

3

 

4

 

 

Host data 8

 

 

Host data 6

 

5

 

6

 

 

Host data 9

 

 

Host data 5

 

7

 

8

 

 

Host data 10

 

 

Host data 4

 

9

 

10

 

 

Host data 11

 

 

Host data 3

 

11

 

12

 

 

Host data

12

 

 

Host data 2

 

13

 

14

 

 

Host data

13

 

 

Host data 1

 

15

 

16

 

 

Host data

14

 

 

Host data 0

 

17

 

18

 

 

Host data

15

 

 

Ground

 

19

 

20

 

 

Key

 

 

 

DRQ1

 

21

 

22

 

 

Ground

 

 

 

Host IOW

 

23

 

24

 

 

Ground

 

 

 

Host IOR

 

25

 

26

 

 

Ground

 

 

 

IOCHRDY

 

27

 

28

 

 

Host ALE

 

 

DACK1

 

29

 

30

 

 

Ground

 

 

 

IRQ15

 

31

 

32

 

 

No connect

 

 

Address 1

 

33

 

34

 

 

No connect

 

 

Address 0

 

35

 

36

 

 

Address

2

 

 

Chip select 0

 

37

 

38

 

 

Chip select 1

 

 

Activity

 

39

 

40

 

 

Ground

 

 

CI5VGM User’s Manual

27

Chapter 2 Installations

J3: External ATX Power Connector

1

 

Pin #

 

 

 

Signal Name

 

 

1

 

 

Dual function power button

 

 

 

 

 

 

 

 

2

 

 

 

GND

 

 

 

3

 

 

Dual function power button

 

6

 

4

 

 

 

GND

 

 

5

 

 

PS-ON (soft on/off)

 

J3

 

6

 

 

5V SB (standby +5V)

 

J18: AT Power Connector

J18

 

Pin #

 

 

Signal Name

 

 

1

 

 

N/A

 

 

2

 

 

+5V

 

 

3

 

 

+12V

 

 

4

 

 

-12V

 

 

5

 

 

GND

 

 

6

 

 

GND

 

J4: Audio I/O Connector (optional)

 

 

Signal Name

 

 

Pin #

 

 

Pin #

 

 

Signal Name

 

 

 

 

+12V

 

1

 

2

 

 

-12V

 

 

 

GND

 

3

 

4

 

 

Out-R

 

 

 

Out-L

 

5

 

6

 

 

GND

 

 

 

Auxi-L

 

7

 

8

 

 

Auxi-R

 

 

 

GND

 

9

 

20

 

 

Line-R

 

 

 

Line-L

 

11

 

12

 

 

GND

 

 

 

Min

 

13

 

14

 

 

VREFO

 

 

 

Vcc

 

15

 

16

 

 

MIC

 

 

 

RxD

 

17

 

18

 

 

TXD

 

 

 

GP7

 

19

 

20

 

 

GP6

 

 

 

GP5

 

21

 

22

 

 

GP4

 

J4

 

GP3

 

23

 

24

 

 

GP2

 

 

GP1

 

25

 

26

 

 

GP0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

 

 

 

 

 

 

 

CI5VGM User’s Manual

Chapter 2 Installations

J4: Audio I/O Connector (Continued)

The J4 Audio I/O Connector connects to the EXTVGM Audio Daughter Card with the 26-pin ribbon cable supplied with the package. The EXTVGM Audio Daughter card provides two CD-AUDIO IN internal connectors and external connectors for LINE OUT, LINE IN, MICROPHONE, and JOYSTICK/MIDI. Refer to the figure below.

J5: USB Connector

15

26

37

4J5 8

 

Pin #

 

 

Signal Name

 

 

1

5

 

 

Vcc

 

 

2

6

 

 

USB-

 

 

3

7

 

 

USB+

 

 

4

8

 

 

Ground

 

CI5VGM User’s Manual

29

Chapter 2 Installations

J6: COM1 Serial Port

 

 

Pin #

 

 

 

Signal Name

 

 

 

1

 

 

DCD, Data carrier detect

 

 

 

2

 

 

RXD, Receive data

 

 

 

3

 

 

TXD, Transmit data

 

 

 

4

 

 

DTR, Data terminal ready

 

J6

 

5

 

 

 

GND, ground

 

 

 

6

 

 

DSR, Data set ready

 

 

 

7

 

 

RTS, Request to send

 

 

 

8

 

 

CTS, Clear to send

 

 

 

9

 

 

 

RI, Ring indicator

 

 

 

10

 

 

 

NC

 

J7: COM2 Serial Port

J7, a 10-pin header connector , is the onboard COM2 serial port of the CI5VGM and is configurable as RS-232, RS-422 or RS-485. The following table shows its pin assignments.

 

Pin #

 

 

Signal Name

 

 

 

 

RS-232

R2-422

RS-485

.

1

 

DCD

 

TX-

DATA-

2

 

RX

 

TX+

DATA+

 

 

 

 

3

 

TX

 

RX+

NC

 

4

 

DTR

 

RX

NC

J7

5

 

GND

 

GND

GND

 

6

 

DSR

 

RTS-

NC

 

7

 

RTS

 

RTS+

NC

 

8

 

CTS

 

CTS+

NC

 

9

 

RI

 

CTS-

NC

 

10

 

NC

 

NC

NC

30

CI5VGM User’s Manual

Chapter 2 Installations

J8: Front Bezel Connector

The front bezel of the case has a control panel which provides light indication of the computer activities and switches to change the computer status. J8 is a 20-pin header that provides interfaces for the following functions.

Hard Disk Drive LED

Reset Switch

Turbo LED Connector

ATX Power On Switch

Not Defined

Power LED and Keylock

Speaker

Speaker: Pins 1 - 4

This connector provides an interface to a speaker for audio tone generation. An 8-ohm speaker is recommended.

 

Pin #

 

 

Signal Name

 

 

1

 

 

Speaker out

 

 

2

 

 

No connect

 

 

3

 

 

Ground

 

 

4

 

 

+5V

 

Power LED and Keylock: Pins 11 - 15

The power LED indicates the status of the main power switch. The keylock switch, when closed, will disable the keyboard function.

 

Pin #

 

 

Signal Name

 

 

11

 

 

Power LED

 

 

12

 

 

No connect

 

 

13

 

 

Ground

 

 

14

 

 

Keylock

 

 

15

 

 

Ground

 

CI5VGM User’s Manual

31

Chapter 2 Installations

ATX Power ON Switch: Pins 7 and 17

This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will force the system to power off.

Turbo LED Connector: Pins 8 and 18

There is no turbo/deturbo function on the CPU card. The Turbo LED on the control panel will always be On when attached to this connector.

 

Pin #

 

 

Signal Name

 

 

8

 

 

5V

 

 

18

 

 

Ground

 

Reset Switch: Pins 9 and 19

The reset switch allows the user to reset the system without turning the main power switch Off and then On.

Hard Disk Drive LED Connector: Pins 10 and 20

This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed.

 

Pin #

 

 

Signal Name

 

 

10

 

 

HDD

 

 

20

 

 

5V

 

32

CI5VGM User’s Manual

Chapter 2 Installations

J9: LCD Panel Connector

J9 is a dual-in-line header for flat panel LCD displays. The following shows the pin assignments of this connector.

 

 

 

Signal Name

 

 

Pin #

 

 

Pin #

 

 

Signal Name

 

 

 

 

+12V

 

1

 

2

 

 

+12V

 

 

 

 

GND

 

3

 

4

 

 

GND

 

 

 

 

+5V/3.3V

 

5

 

6

 

 

+5V/3.3V

 

 

 

 

ENPVEE

 

7

 

8

 

 

GND

 

58

57

 

P0

 

9

 

10

 

 

P1

 

 

P2

 

11

 

12

 

 

P3

 

 

 

 

P4

 

13

 

14

 

 

P5

 

 

 

 

P6

 

15

 

16

 

 

P7

 

 

 

 

P8

 

17

 

18

 

 

P9

 

 

 

 

P10

 

19

 

20

 

 

P11

 

 

 

 

P12

 

21

 

22

 

 

P13

 

 

 

 

P14

 

23

 

24

 

 

P15

 

 

 

 

P16

 

25

 

26

 

 

P17

 

 

 

 

P18

 

27

 

28

 

 

P19

 

 

 

 

P20

 

29

 

30

 

 

P21

 

 

 

 

P22

 

31

 

32

 

 

P23

 

 

 

 

GND

 

33

 

34

 

 

GND

 

 

 

 

SHFCLK

 

35

 

36

 

 

FLM

 

 

 

 

DE

 

37

 

38

 

 

LP

 

2

1

 

GND

 

39

 

40

 

 

ENBLT

 

 

GND

 

41

 

42

 

 

PVDD

 

 

 

 

ENPVDD

 

43

 

44

 

 

+5V/3.3V

 

 

 

 

No Connect

 

45

 

46

 

 

No Connect

 

 

 

 

P24

 

47

 

48

 

 

P25

 

 

 

 

P26

 

49

 

50

 

 

P27

 

 

 

 

P28

 

51

 

52

 

 

P29

 

 

 

 

P30

 

53

 

54

 

 

P31

 

 

 

 

P32

 

55

 

56

 

 

P33

 

 

 

 

P34

 

57

 

58

 

 

P35

 

CI5VGM User’s Manual

33

Chapter 2 Installations

J14: Chassis Fan Power Connector

J14 is a 3-pin header for the chassis fan. The fan must be a 12V fan.

 

 

 

Pin #

 

Signal Name

 

 

 

1

 

Rotation

1

2

3

2

 

+12V

3

 

Ground

 

 

 

 

J22, J23: CPU Fan Power Connectors

J22 and J23 are pin headers for the CPU fan. The fan must be a 12V fan.

 

 

 

Pin #

 

Signal Name

 

 

 

1

 

Rotation

1

2

3

2

 

+12V

3

 

Ground

 

 

 

 

 

 

 

 

 

 

 

 

Pin #

 

Signal Name

 

1 2

 

1

 

+5V

 

 

2

 

Ground

 

J15: IrDA Connector

J15 is used for an IrDA connector for wireless communication.

+5V IRRX IRTX

 

Pin #

 

 

Signal Name

 

 

1

 

 

+5V

 

 

 

2

 

 

No connect

 

N.C. GND

 

3

 

 

Ir RX

 

 

4

 

 

Ground

 

 

 

5

 

 

Ir TX

 

J16: External Keyboard Connector

 

Pin #

 

Signal Name

 

 

1

 

Keyboard clock

 

 

2

 

Keyboard data

 

 

3

 

PG

 

J16

4

 

GND

 

5

 

Vcc

 

 

 

 

 

 

34

 

 

CI5VGM User’s Manual

Chapter 2 Installations

J17: External Mouse Connector

 

 

Pin #

 

 

Signal Name

 

 

 

1

 

 

Mouse data

 

 

 

2

 

 

Ground

 

 

 

3

 

 

5V

 

J17

 

4

 

 

Mouse Clock

 

J19: PS/2 Keyboard Connector

 

 

Pin #

 

 

Signal Name

 

 

 

1

 

 

Keyboard data

 

 

 

2

 

 

N.C.

 

 

 

3

 

 

Ground

 

J19

 

4

 

 

5V

 

 

5

 

 

Keyboard clock

 

 

 

6

 

 

N.C.

 

J20: PS/2 Mouse Connector

 

 

Pin #

 

 

Signal Name

 

 

 

1

 

 

Mouse data

 

 

 

2

 

 

N.C.

 

 

 

3

 

 

Ground

 

J20

 

4

 

 

5V

 

 

5

 

 

Mouse Clock

 

 

 

6

 

 

N.C.

 

CI5VGM User’s Manual

35

Chapter 2 Installations

J21: VGA CRT Connector

 

 

Signal Name

 

 

Pin #

 

 

Pin #

 

 

Signal Name

 

 

 

Red

 

1

 

2

 

 

Green

 

 

 

Blue

 

3

 

4

 

 

N.C.

 

 

 

GND

 

5

 

6

 

 

GND

 

 

 

GND

 

7

 

8

 

 

GND

 

J21

 

N.C.

 

9

 

10

 

 

GND

 

 

 

N.C.

 

11

 

12

 

 

N.C.

 

 

 

HSYNC

 

13

 

14

 

 

VSYNC

 

 

 

NC

 

15

 

 

 

 

 

 

 

J25: RJ45 Connector

This connector is for the 10/100Mbps Ethernet capability of the CPU card The figure below shows the pin out assignments of this connector and its corresponding input jack.

TD+(pin#1)

TD-(pin#2)

RD+(pin#3)

RD-(pin#5)

36

CI5VGM User’s Manual

Chapter 2 Installations

Watchdog Timer Configuration

The function of the watchdog timer is to reset the system automatically and is defined at I/O port 0443H. To enable the watchdog timer and allow the system to reset, write I/O port 0443H. To disable the timer, write I/O port 0441H for the system to stop the watchdog function. The timer has a tolerance of 20% for its intervals.

The following describes how the timer should be programmed.

Enabling Watchdog:

 

 

 

 

 

 

 

 

 

MOV

AX, 000FH (Choose the values from 0)

 

 

 

 

MOV

DX, 0443H

 

 

 

 

 

 

 

 

 

OUT

DX, AX

 

 

 

 

 

 

 

 

 

Disabling Watchdog

 

 

 

 

 

 

 

 

 

MOV

AX, 00FH (Any value is fine.)

 

 

 

 

MOV

DX, 0441H

 

 

 

 

 

 

 

 

 

OUT

DX, AX

 

 

 

 

 

 

 

 

 

 

 

 

WATCHDOG TIMER CONTROL TABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Level

 

 

Value

 

 

Time/sec

Level

 

Value

 

 

Time/sec

1

 

 

F

 

0

9

 

7

 

16

2

 

 

E

 

2

10

 

6

 

18

3

 

 

D

 

4

11

 

5

 

20

4

 

 

C

 

6

12

 

4

 

22

5

 

 

B

 

8

13

 

3

 

24

6

 

 

A

 

10

14

 

2

 

26

7

 

 

9

 

12

15

 

1

 

28

8

 

 

8

 

14

16

 

0

 

30

CI5VGM User’s Manual

37

Chapter 3 BIOS Configuration

This page was intentionally left blank.

38

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

3

BIOS Configuration

This chapter describes the different settings available in the Award BIOS that comes with the CI5VGM CPU card. The topics covered in this chapter are as follows:

BIOS Introduction..............................................................

42

BIOS Setup ........................................................................

42

Standard CMOS Setup .......................................................

44

Date .........................................................................

44

Time ........................................................................

45

Primary HDDs / Secondary HDDs ..........................

45

Drive A / Drive B ....................................................

46

Video .......................................................................

46

Halt On ....................................................................

46

BIOS Features Setup..........................................................

47

Virus Warning .........................................................

47

CPU Internal Cache / External Cache......................

47

Quick Power On Self Test .......................................

48

Boot Sequence.........................................................

48

Swap Floppy Drive..................................................

48

Boot Up Floppy Seek ..............................................

48

Boot Up NumLock Status........................................

48

Boot Up System Speed............................................

48

Gate A20 Option .....................................................

48

Memory Parity / ECC Check...................................

48

Typematic Rate Setting............................................

49

Typematic Rate (Chars/Sec)....................................

49

Typematic Delay (Msec) .........................................

49

Security Option........................................................

49

CI5VGM User’s Manual

39

Chapter 3 BIOS Configuration

 

 

PCI/VGA Palette Snoop ..........................................

49

 

OS Select for DRAM > 64MB ................................

49

 

HDD S.M.A.R.T. Capability ...................................

49

 

Video BIOS Shadow................................................

50

 

C8000 - CBFFF Shadow/DC000 - DFFFF Shadow 50

 

Chipset Features Setup .......................................................

51

 

DRAM Timing.........................................................

51

 

SDRAM Cycle Length.............................................

51

 

DRAM Read Pipeline ..............................................

51

 

Cache Rd+CPU Wt Pipeline....................................

51

 

Cache Timing...........................................................

51

 

Video BIOS Cacheable............................................

52

 

System BIOS Cacheable ..........................................

52

 

Memory Hole at 15MB - 16MB ..............................

52

 

AGP Aperture Size (MB) ........................................

52

 

Cyrix M2 ADS# delay .............................................

50

 

Auto Detect DIMM/PCI Clk....................................

50

 

Spread Spectrum......................................................

50

 

OnChip USB............................................................

52

 

USB Keyboard Support ...........................................

51

 

CPU Warning Temperature .....................................

53

 

Temperature/Fan Speed/ Voltage ............................

51

 

Shutdown Temperature............................................

51

 

Power Management Setup..................................................

54

 

ACPI function..........................................................

54

 

Power Management .................................................

54

 

PM Control by APM................................................

55

 

Video Off Option.....................................................

55

 

Video Off Method....................................................

55

 

Modem Use IRQ......................................................

55

 

Soft-Off by PWR-BTTN .........................................

55

 

HDD Power Down...................................................

55

 

Doze Mode ..............................................................

55

 

Suspend Mode .........................................................

56

 

PM Events................................................................

56

 

PNP/PCI Configuration......................................................

57

 

PNP OS Installed .....................................................

57

 

Resources Controlled by..........................................

57

 

Reset Configuration Data.........................................

57

 

IRQ3/4/5/7/9/10/11/12/14/15, DMA0/1/3/5/6/7

 

 

assigned to ...............................................................

57

40

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

Load BIOS Defaults...........................................................

59

Load Setup Defaults...........................................................

59

Integrated Peripherals ........................................................

60

OnChip IDE First/Second Channel..........................

58

IDE Prefetch Mode..................................................

60

IDE HDD Block Mode............................................

60

IDE Primary/Secondary Master/Slave PIO .............

60

IDE Primary/Secondary Master/Slave UDMA .............

61

Init AGP Display First.............................................

61

Onboard Audio Chip ...............................................

61

Onboard FDD Controller.........................................

61

Onboard Serial/Parallel Port....................................

61

UART 2 Mode.........................................................

61

Parallel Port Mode...................................................

61

Supervisor / User Password ...............................................

62

IDE HDD Auto Detection..................................................

63

Save & Exit Setup ..............................................................

64

Exit Without Saving...........................................................

64

CI5VGM User’s Manual

41

Chapter 3 BIOS Configuration

BIOS Introduction

The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Pentium II processors in a standard IBM-AT compatible I/O system. The BIOS provides critical low-level support for standard devices such as disk drives, serial and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.

BIOS Setup

The Award BIOS provides a Setup utility program for specifying the system configurations and settings. The BIOS ROM of the system stores the Setup utility. When you turn on the computer, the Award BIOS is immediately activated. Pressing the <Del> key immediately allows you to enter the Setup utility. If you are a little bit late pressing the <Del> key, POST (Power On Self Test) will continue with its test routines, thus preventing you from invoking the Setup. If you still wish to enter Setup, r e s t a r t t h e s y s t e m b y p r e or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the system Off and back On again. The following message will appear on the screen:

Press <DEL> to Enter Setup

In general, you press the arrow keys to highlight items, <Enter> to select, the <PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit.

When you enter the Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices.

42

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

INTEGRATED PERIPHERALS

BIOS FEATURES SETUP

SUPERVISOR PASSWORD

CHIPSET FEATURES SETUP

USER PASSWORD

POWER MANAGEMENT SETUP

IDE HDD AUTO DETECTION

PNP/PCI CONFIGURATION

HDD LOW LEVEL FORMAT

LOAD BIOS DEFAULTS

SAVE & EXIT SETUP

LOAD SETUP DEFAULTS

EXIT WITHOUT SAVING

ESC : Quit

Ç È Æ Å : Select Item

F10 : Save & Exit Setup

(Shift) F2 : Change Color

Time, Date, Hard Disk Type

The section below the setup items of the Main Menu displays the control keys for this menu. Another section at the bottom of the Main Menu just below the control keys section displays information on the currently highlighted item in the list.

NOTE: After making and saving system changes with Setup, you find that your computer cannot boot, the Award BIOS supports an override to the CMOS settings that resets your system to its default.

We strongly recommend that you avoid making any changes to the chipset defaults. These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability.

CI5VGM User’s Manual

43

Chapter 3 BIOS Configuration

Standard CMOS Setup

“Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.

ROM PCI/ISA BIOS

STANDARD CMOS SETUP

AWARD SOFTWARE, INC.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Date (mm:dd:yy) : Wed, Mar 4 1998

 

 

 

 

 

 

 

 

 

 

 

Time (hh:mm:ss) :

00 : 00 : 00

 

 

 

 

 

 

 

 

 

 

 

HARD DISKS

TYPE

SIZE

CYLS

HEAD

PRECOMP

LANDZ

SECTOR

MODE

 

 

Primary Master

Auto

0

0

0

 

0

0

0

Auto

 

 

Primary Slave

Auto

0

0

0

 

0

0

0

Auto

 

 

Secondary Master

Auto

0

0

0

 

0

0

0

Auto

 

 

Secondary Slave

Auto

0

0

0

 

0

0

0

Auto

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drive A

: 1.44M, 3.5in

 

 

 

 

Base Memory

:

640K

 

 

Drive B

: None

 

 

 

 

Extended Memory

:

15360K

 

 

 

 

 

 

 

 

 

 

Other Memory

:

384K

 

 

Video

: EGA / VGA

 

 

 

 

 

 

 

 

 

 

 

Halt On

: All Errors

 

 

 

 

Total Memory

:

16384K

 

 

ESC : Quit

 

 

Ç È Æ Å : Select

 

Item

PU / PD / + / - : Modify

 

 

F1 : Help

 

 

(Shift) F2

: Change Color

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

At the bottom of the menu are the control keys for use on this menu. If you need any help in each item field, you can press the <F1> key. It will display the relevant information to help you. The memory display at the lower right-hand side of the menu is read-only. It will adjust automatically according to the memory changed. The following describes the items of this menu.

Date

The date format is:

Day :

Sun to Sat

Month :

1 to 12

Date :

1 to 31

Year :

1994 to 2079

To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to set the current time.

44

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

Time

The time format is: Hour : 00 to 23

Minute : 00 to 59 Second : 00 to 59

To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or +/- keys to set the current time.

Primary HDDs / Secondary HDDs

The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices. Each channel can support up to two hard disks; the first is the “Master” and the second is the “Slave”.

To enter the specifications for a hard disk drive, you must select first a “Type”. There are 45 predefined types and 4 user definable types are for Enhanced IDE BIOS. Type 1 to 45 are predefined. Type “User” is user-definable. For the Primary Master/Slave as well as Secondary Master/Slave, you can select “Auto” under the TYPE and MODE fields. This will enable auto detection of your IDE drives and CD-ROM drive during POST.

Press <PgUp>/<PgDn> to select a numbered hard disk type or type the number and press the <Enter> key. The hard disk will not work properly if you enter incorrect information for this field. If your hard disk drive type is not matched or listed, you can use Type User to define your own drive type manually. If you select Type User, related information is asked to be entered to the following items.

CYLS :

Number of cylinders

 

HEAD :

Number of read/write heads

PRECOMP :

Write precompensation

 

LANDZ :

Landing zone

 

SECTOR :

Number of sectors

 

SIZE :

Automatically adjust according to the configuration

MODE (for IDE HDD only) : Auto

 

 

Normal (HD < 528MB)

 

Large

(for MS-DOS only)

 

LBA

(HD > 528MB and supports

 

 

Logical Block Addressing)

CI5VGM User’s Manual

45

The system boot will not be halted for any error that may be detected.
Whenever the BIOS detects a non-fatal error, the system will stop and you will be prompted. The system boot will not be halted for a keyboard error; it will stop for all other errors The system boot will not be halted for a disk error; it will stop for all other errors.
The system boot will not be halted for a keyboard or disk error; it will stop for all others.
CI5VGM User’s Manual

Chapter 3 BIOS Configuration

NOTE: The specifications of your drive must match with the drive table. The hard disk will not work properly if you enter incorrect information in these fields. If your hard disk drive type is not matched or listed, you can use Type User to define your own drive type manually.

Drive A / Drive B

These fields identify the types of floppy disk drive A or drive B that has been installed in the computer. The available specifications are:

360KB 1.2MB 720KB 1.44MB 2.88MB 5.25 in. 5.25 in. 3.5 in. 3.5 in. 3.5 in.

Video

This field selects the type of video display card installed in your system. You can choose the following video display cards:

EGA/VGA

For EGA, VGA, SEGA, SVGA

 

or PGA monitor adapters. (default)

CGA 40

Power up in 40 column mode.

CGA 80

Power up in 80 column mode.

MONO

For Hercules or MDA adapters.

Halt On

This field determines whether the system will halt if an error is detected during power up.

No errors

All errors

All, But Keyboard

All, But Diskette

All, But Disk/Key

46

Chapter 3 BIOS Configuration

BIOS Features Setup

This section allows you to configure and improve your system and allows you to set up some system features according to your preference.

ROM / PCI ISA BIOS

BIOS FEATURES SETUP

AWARD SOFTWARE, INC.

 

 

 

 

 

 

 

Virus Warning

: Disabled

Video BIOS Shadow

: Enabled

 

 

CPU Internal Cache

: Enabled

C8000-CBFFF Shadow

: Disabled

 

 

External Cache

: Enabled

CC000-CFFFF Shadow

: Disabled

 

 

Quick Power On Self Test

: Enabled

D0000-D3FFF Shadow

: Disabled

 

 

Boot Sequence

: A, C, SCSI

D4000-D7FFF Shadow

: Disabled

 

 

Swap Floppy Drive

: Disabled

D8000-DBFFF Shadow

: Disabled

 

 

Boot Up Floppy Drive

: Enabled

DC000-DFFF Shadow

: Disabled

 

 

Boot Up Numlock Status

: On

 

 

 

 

Boot Up System Speed

: High

 

 

 

 

Gate A20 Option

: Fast

 

 

 

 

Memory Parity / ECC Check

: Disabled

 

 

 

 

Typematic Rate Setting

: Disabled

 

 

 

 

Typematic Rate (chars/Sec)

: 6

 

 

 

 

Typematic Delay (Msec)

: 250

 

 

 

 

Security Option

: Setup

 

 

 

 

PCI /VGA Palette Snoop

: Disabled

ESC : Quit

Ç È Æ Å : Select Item

 

 

OS Select For DRAM>64MB

: Non-OS2

F1 : Help

PU/PD/+/- : Modify

 

 

HDD S.M.A.R.T. capability

: Enabled

F5 : Old Values

(Shift) F2 : Color

 

 

 

 

F6 : Load BIOS Defaults

 

 

 

 

F7 : Load Setup Defaults

 

 

 

 

 

 

 

Virus Warning

This item protects the boot sector and partition table of your hard disk against accidental modifications. If an attempt is made, the BIOS will halt the system and display a warning message. If this occurs, you can either allow the operation to continue or run an anti-virus program to locate and remove the problem.

NOTE: Many disk diagnostic programs which attempt to access the boot sector table can cause the virus warning. If you will run such a program, disable the Virus Warning feature.

CPU Internal Cache / External Cache

Cache memory is additional memory that is much faster than conventional DRAM (system memory). CPUs from 486-type on up contain internal cache memory, and most, but not all, modern PCs have additional (external) cache memory. When the CPU requests data, the system transfers the requested data from the main DRAM into cache memory, for even faster access by the CPU. These items allow you to enable (speed up memory access) or disable the cache function. By default, these items are Enabled.

CI5VGM User’s Manual

47

Chapter 3 BIOS Configuration

Quick Power On Self Test

When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items.

Boot Sequence

This field determines the drive that the system searches first for an operating system. The options are :

 

A, C, SCSI

D, A, SCSI

SCSI, C, A

 

C, A, SCSI

E, A, SCSI

C only

 

C, CDROM, A

F, A, SCSI

LS/ZIP, C

 

CDROM, C, A

SCSI, A, C

 

The default value is A, C, SCSI.

 

 

Swap Floppy Drive

This item allows you to determine whether or not to enable Swap Floppy Drive. When enabled, the BIOS swaps floppy drive assignments so that Drive A becomes Drive B, and Drive B becomes Drive A. By default, this field is set to Disabled.

Boot Up Floppy Seek

When enabled, the BIOS will seek whether or not the floppy drive installed has 40 or 80 tracks. 360K type has 40 tracks while 760K, 1.2M and 1.44M all have 80 tracks. By default, this field is set to Enabled.

Boot Up NumLock Status

This allows you to activate the NumLock function after you power up the system. By default, the system boots up with NumLock On.

Boot Up System Speed

Leave the default setting of the system speed at High.

Gate A20 Option

This field allows you to select how Gate A20 is worked. Gate A20 is a device used to address memory above 1 MB. The default setting is Fast.

Memory Parity / ECC Check

When enabled, this allows ECC checking of the CPU’s L2 cache. By default, this field is Disabled.

48

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

Typematic Rate Setting

When disabled, continually holding down a key on your keyboard will generate only one instance. When enabled, you can set the two typematic controls listed next. By default, this field is set to Disabled.

Typematic Rate (Chars/Sec)

When the typematic rate is enabled, the system registers repeated keystrokes speeds. You can select speed range from 6 to 30 characters per second. By default, this item is set to 6.

Typematic Delay (Msec)

When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec.

Security Option

This field allows you to limit access to the System and Setup. The default value is Setup. When you select System, the system prompts for the User Password every time you boot up. When you select Setup, the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up.

PCI/VGA Palette Snoop

Some non-standard VGA display cards may not show colors properly. This field allows you to set whether or not MPEG ISA/VESA VGA Cards can work with PCI/VGA. When this field is enabled, a PCI/VGA can work with an MPEG ISA/VESA VGA card. When this field is disabled, a PCI/VGA cannot work with an MPEG ISA/VESA Card.

OS Select for DRAM > 64MB

This option allows the system to access greater than 64MB of DRAM memory when used with OS/2 that depends on certain BIOS calls to access memory. The default setting is Non-OS/2.

HDD S.M.A.R.T. Capability

This option enables or disables the S.M.A.R.T. feature found in some hard disks. The default setting is Enabled.

CI5VGM User’s Manual

49

Chapter 3 BIOS Configuration

Video BIOS Shadow

This item allows you to change the Video BIOS location from ROM to RAM. Video Shadow will increase the video speed.

C8000 - CBFFF Shadow/DC000 - DFFFF Shadow

Shadowing a ROM reduces the memory available between 640KB to 1024KB. These fields determine whether or not optional ROM will be copied to RAM.

50

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

Chipset Features Setup

This Setup menu controls the configuration of the motherboard chipset.

ROM PCI/ISA BIOS

CHIPSET FEATURES SETUP

AWARD SOFTWARE INC.

 

 

 

 

 

 

 

 

 

 

Bank 0/1 DRAM Timing

:

SDRAM 8ns

CPU Warning Temperature

: 66° C/151° F

 

 

Bank 2/3 DRAM Timing

:

SDRAM 8ns

Current System Temp.

 

:

 

 

Bank 4/5 DRAM Timing

:

SDRAM 8ns

Current CPU Temp.

 

:

 

 

SDRAM Cycle Length

:

3

Current CPU Fan Speed

:

 

 

DRAM Read Pipeline

:

Enabled

Current Chassis Fan Speed

:

 

 

Sustained 3T Write

:

Enabled

VCORE

:

VCC3

:

 

 

Cache Rd+CPU Wt Pipeline

:

Disabled

+12V

:

+5V

:

 

 

Cache Timing

:

Fast

-5V

:-

-12V

:-

 

 

Video BIOS Cacheable

:

Enabled

Shutdown Temperature

: 75° C/167° F

 

 

System BIOS Cacheable

:

Disabled

 

 

 

 

 

 

Memory Hole At 15MB-16MB

:

Disabled

 

 

 

 

 

 

AGP Aperture Size

:

64M

 

 

 

 

 

 

Cyrix M2 ADS# delay

: Disabled

 

 

 

 

 

 

 

:

 

 

 

 

 

 

 

Auto Detect DIMM/PCI Clk

: Disabled

 

 

 

 

 

 

Spread Spectrum

: Disabled

ESC : Quit

 

Ç È Æ Å : Select Item

 

 

 

 

 

F1 : Help

 

PU/PD/+/- : Modify

 

 

OnChip USB

: Enabled

F5 : Old Values

(Shift) F2 : Color

 

 

USB Keyboard Support

: Disabled

F6 : Load BIOS Defaults

 

 

 

 

 

 

F7 : Load Setup Defaults

 

 

 

 

 

 

 

 

 

 

 

DRAM Timing

The DRAM timing is controlled by the DRAM Timing Registers. The timing type is dependent on the system design. Slower rates may be required in some system designs to support loose layouts or slower memory.

SDRAM Cycle Length

This field sets the length of each SDRAM cycle. By default, this field is set to 3.

DRAM Read Pipeline

When enabled, this field supports pipelining of DRAM reads.

Sustained 3T Write

This field allows support for PBSRAM sustained 3T writes.

Cache Rd+CPU Wt Pipeline

When enabled, this item allows pipelining of cache reads and CPU writes.

Cache Timing

This field sets the timing of the cache in the system. The options are fast and fastest. By default, this field is set to fast.

CI5VGM User’s Manual

51

Chapter 3 BIOS Configuration

Video BIOS Cacheable

When enabled, access to video BIOS addressed at C0000H to C7FFFH is cached, provided that the cache controller is disabled.

System BIOS Cacheable

When enabled, access to the system BIOS ROM addressed at F0000H-FFFFFH is cached, provided that the cache controller is disabled.

Memory Hole at 15MB - 16MB

In order to improve performance, certain space in memory can be reserved for ISA cards. This field allows you to reserve 15MB to 16MB memory address space to ISA expansion cards. This makes memory from 15MB and up unavailable to the system. Expansion cards can only access memory up to 16MB. By default, this field is set to Disabled.

AGP Aperture Size (MB)

The field sets aperture size of the graphics. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation. The options available are 4M, 8M, 16M, 32M, 64M, 128M and 256M. The default setting is 64M.

Cyrix M2 ADS# delay

This field is only visible when your system supports a Cyrix M2 processor. It enables or disables the ADS# delay signal for Cyrix M2.

Auto Detect DIMM/PCI Clk

When enabled, the system automatically shuts off clocks of unused DIMM/PCI slots. The default setting is Disabled. This field is for CE testing use only.

Spread Spectrum

This field sets the value of the spread spectrum. Options are Disabled, 1.8% (CNTR), 0.6% (CNTR), 1.8% (DOWN), and 0.6% (DOWN). The default setting is 0.6% (DOWN). The default setting is Disabled. This field is for CE testing use only.

OnChip USB

This filed allows you to enable or disable the USB function. The default setting is Enabled.

52

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

USB Keyboard Support

The field enables or disables the support for a USB keyboard.

CPU Warning Temperature

This field sets the threshold temperature at which an alert is sounded through the system’s speaker. The CPU temperature is monitored by the onboard thermal sensor to prevent the CPU from overheating.

Temperature/Fan Speed/Voltage

The values for the system/CPU temperature, CPU/chassis fan speed and system voltages are displayed as monitored by the H/W monitoring IC.

Shutdown Temperature

To avoid hardware damage due to overheat, this field can be configured so that the system shuts down automatically when it reaches the set temperature.

CI5VGM User’s Manual

53

Chapter 3 BIOS Configuration

Power Management Setup

The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn off video display after a period of inactivity.

ROM PCI/ISA BIOS

POWER MANAGEMENT SETUP

AWARD SOFTWARE, INC.

 

 

 

 

 

 

 

 

 

ACPI function

: Enabled

Primary INTR

 

: ON

 

 

Power Management

: User Define

IRQ3

(COM 2)

 

: Primary

 

 

PM Control by APM

: Yes

IRQ4

(COM 1)

 

: Primary

 

 

Video Off Option

: Suspend -> Off

IRQ5

(LPT 2)

 

: Primary

 

 

Video Off Method

: V/H SYNC +Blank

IRQ6

(Floppy Disk)

: Primary

 

 

MODEM Use IRQ

: 3

IRQ7

(LPT 1)

 

: Primary

 

 

Soft-Off by PWRBTN

: Instant-Off

IRQ8

(RTC Alarm)

 

: Disabled

 

 

** PM Timers **

IRQ9

(IRQ2 Redir)

 

: Secondary

 

 

HDD Power Down

: Disabled

IRQ10

(Reserved)

 

: Secondary

 

 

Doze Mode

: Disabled

IRQ11

(Reserved)

 

: Secondary

 

 

Suspend Mode

: Disabled

IRQ12

(PS/2 Mouse)

: Primary

 

 

** PM Events **

IRQ13

(Coprocessor)

: Primary

 

 

VGA

: OFF

IRQ14

(Hard Disk)

 

: Primary

 

 

LPT & COM

: LPT/COM

IRQ15

(Reserved)

 

: Primary

 

 

HDD & FDD

: ON

 

 

 

 

 

 

DMA/master

: OFF

ESC : Quit

 

Ç È Æ Å : Select Item

 

 

PWR-ON by Modem/LAN

: Disabled

F1 : Help

 

PU/PD/+/- : Modify

 

 

RTC Alarm Resume

: Disabled

F5 : Old Values

(Shift) F2 : Color

 

 

 

 

F6 : Load BIOS Defaults

 

 

 

 

 

F7 : Load Setup Defaults

 

 

 

 

 

 

 

 

 

 

ACPI function

This field enables or disables the ACPI function.

Power Management

This field allows you to select the type of power saving management modes. There are fours selections for Power Management.

Min. Power Saving

Minimum power management

Max. Power Saving

Maximum power management.

User Define

Each of the ranges are from 1 min. to

 

1hr. Except for HDD Power Down

 

which ranges from 1 min. to 15 min.

 

(Default)

NOTE: In order to enable the CPU overheat protection feature, the Power Management field should not be set to Disabled.

54

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

PM Control by APM

This field allows you to use the Advanced Power Management device to enhance the Max. Power Saving mode and stop the CPU’s internal clock. If the Max. Power Saving is not enabled, this will be preset to NO.

Video Off Option

The Video Off options are Suspend -> Off, Always On, and All Modes -> Off. By default, this field is set to Suspend -> Off.

Video Off Method

This field defines the Video Off features. There are three options.

V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning.

DPMS

Allows the BIOS to control the video display card if it

 

supports the DPMS feature.

Blank Screen

This option only writes blanks to the video buffer.

Modem Use IRQ

This field names the interrupt request (IRQ) line assigned to the modem (if any) on your system. Activity of the selected IRQ always awakens the system. By default, the IRQ is set to 3.

Soft-Off by PWR-BTTN

This field defines the power-off mode when using an ATX power supply. The Instant-Off mode allows powering off immediately upon pressing the power button. In the Delay 4 Sec mode, the system powers off when the power button is pressed for more than four seconds or places the system in a very low-power-usage state, with only enough circuitry receiving power to detect power button activity or Resume by Ring activity (see next field) when pressed for less than 4 seconds. The default value is Instant-Off.

HDD Power Down

When enabled, and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active.

Doze Mode

When enabled, and after the set time of system inactivity, the CPU clock will run at a slower speed while all other devices still operate at full speed.

CI5VGM User’s Manual

55

Chapter 3 BIOS Configuration

Suspend Mode

When enabled, and after the set time of system inactivity, all devices except the CPU will be shut off.

PM Events

The VGA, LPT & COM, HDD & FDD, DMA/master, PWR-ON by Modem/LAN, RTC Alarm Resume, and Primary INTR sections are I/O events which can prevent the system from entering a power saving mode or can awaken the system from such a mode. When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur. When the operating system is ready to respond to the request, it interrupts itself and performs the service. When set to ON, activity will neither prevent the system from going into a power management mode nor awaken it. The IRQ section sets the wake-up call of the system. If activity is detected from any enabled IRQ channels in the left-hand group, the system wakes up from Suspend Mode.

56

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

PNP/PCI Configuration

This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.

ROM PCI/ISA BIOS

PNP/PCI CONFIGURATION

AWARD SOFTWARE INC.

 

 

 

 

 

 

 

 

 

 

PNP OS Installed

 

: No

CPU to PCI Write Buffer

: Enabled

 

 

Resources Controlled by

: Manual

PCI Dynamic Bursting

 

: Enabled

 

 

Reset Configuration Data

: Disabled

PCI Master 0 WS Write

 

: Disabled

 

 

 

 

 

 

PCI Delay Transaction

 

: Enabled

 

 

IRQ-3

assigned

to

: Legacy ISA

PCI Master Read Prefetch

: Enabled

 

 

IRQ-4

assigned

to

: Legacy ISA

PCI#2 Access #1 Retry

 

: Disabled

 

 

IRQ-5

assigned

to

: PCI/ISA PnP

AGP Master 1 WS Write

: Enabled

 

 

IRQ-7

assigned

to

: Legacy ISA

AGP Master 1 WS Read

: Disabled

 

 

IRQ-9

assigned

to

: PCI/ISA PnP

 

 

 

 

 

IRQ-10 assigned to

: PCI/ISA PnP

PCI IRQ Activated By

 

: Level

 

 

IRQ-11 assigned to

: PCI/ISA PnP

Assign IRQ for USB

 

: Enabled

 

 

IRQ-12 assigned to

: PCI/ISA PnP

Assign IRQ for VGA

 

: Enabled

 

 

IRQ-14 assigned to

: PCI/ISA PnP

 

 

 

 

 

IRQ-15 assigned to

: PCI/ISA PnP

 

 

 

 

 

DMA-0 assigned to

: PCI/ISA PnP

 

 

 

 

 

DMA-1 assigned to

: PCI/ISA PnP

ESC : Quit

Ç È Å : Select Item

 

 

DMA-3 assigned to

: PCI/ISA PnP

F1 : Help

PU/PD/+/- : Modify

 

 

DMA-5 assigned to

: PCI/ISA PnP

F5 : Old Values

(Shift) F2 : Color

 

 

DMA-6 assigned to

: PCI/ISA PnP

F6 : Load BIOS Defaults

 

 

 

DMA-7

assigned

to

: PCI/ISA PnP

F7 : Load Setup Defaults

 

 

 

 

 

 

 

 

 

 

 

PNP OS Installed

This field allows you to specify if the operating system installed in your system is plug and play aware.

NOTE: Operating systems such as DOS, OS/2, and Windows 3.x do not use PnP

Resources Controlled by

This PnP BIOS can configure all of the boot and compatible devices automatically. However, this capability needs you to use a PnP operating system such as Windows 95. The default value is Manual.

Reset Configuration Data

This field allows you to determine whether or not to reset the configuration data. The default value is Disabled.

IRQ3/4/5/7/9/10/11/12/14/15, DMA0/1/3/5/6/7 assigned to

These fields allow you to determine the IRQ/DMA assigned to the ISA bus and is not available to any PCI slot.

CI5VGM User’s Manual

57

Chapter 3 BIOS Configuration

CPU to PCI Write Buffer

When enabled, this option increases the efficiency of the PCI bus to and speed up the execution in the processor. By default, this field is set to

Enabled.

PCI Dynamic Bursting

When enabled, this option combines several PCI cycles into one. By default, this field is set to Disabled.

PCI Master 0 WS Write

When enabled, this option increases the write cycle speed. By default, this field is set to Disabled.

PCI Delay Transaction

When enabled, this option delays PCI data transactions.

PCI Master Read Prefetch

When this item is enabled, the system is allowed to prefetch the next read and initiate the next process.

PCI #2 Access #1 Retry

This item enables PCI#2 Access#1 attempts. By default, this field is set to

Disabled.

AGP Master 1 WS Write

When enabled, writes to the AGP bus are executed with 1 wait states. By default, this field is set to Enabled.

AGP Master 1 WS Read

When enabled, reads to the AGP bus are executed with 1 wait states. By default, this field is set to Disabled.

PCI IRQ Activated By

This field allows you to select the method by which the PCI bus recognizes that an IRQ service is being requested by a device. The default value is Level.

Assign IRQ For USB / VGA

When enabled, an IRQ would be assigned to these items.

58

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

Load BIOS Defaults

This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

 

INTEGRATED PERIPHERALS

BIOS FEATURES SETUP

 

SUPERVISOR PASSWORD

CHIPSET FEATURES SETUP

 

USER PASSWORD

 

 

 

 

DETECTION

POWER MANAGEMENT SETUP

 

IDE HDD AUTO

PNP/PCI CONFIGURATION

 

HDD LOW LEVEL

FORMAT

 

Load BIOS Defaults (Y/N)? N

 

LOAD BIOS DEFAULTS

 

SAVE & EXIT SETUP

LOAD SETUP

DEFAULTS

 

EXIT WITHOUT

SAVING

 

ESC : Quit

 

Ç È Æ Å : Select Item

F10 : Save & Exit Setup

 

(Shift) F2 : Change Color

Load BIOS Defaults except Standard CMOS Setup

To load BIOS defaults value to CMOS SRAM, enter “Y”. If not, enter “N”.

Load Setup Defaults

This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

 

INTEGRATED PERIPHERALS

BIOS FEATURES SETUP

 

SUPERVISOR PASSWORD

CHIPSET FEATURES SETUP

 

USER PASSWORD

 

 

 

 

DETECTION

POWER MANAGEMENT SETUP

 

IDE HDD AUTO

PNP/PCI CONFIGURATION

 

HDD LOW LEVEL

FORMAT

 

Load Setup Defaults (Y/N)? N

 

LOAD BIOS DEFAULTS

 

SAVE & EXIT SETUP

LOAD SETUP

DEFAULTS

 

EXIT WITHOUT

SAVING

 

ESC : Quit

 

Ç È Æ Å : Select Item

F10 : Save & Exit Setup

 

(Shift) F2 : Change Color

Load BIOS Defaults except Standard CMOS Setup

To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter “N”.

CI5VGM User’s Manual

59

Chapter 3 BIOS Configuration

Integrated Peripherals

This option sets your hard disk configuration, mode and port.

ROM PCI/ISA BIOS

INTEGRATED PERIPHERALSP

AWARD SOFTWARE INC.

 

 

 

 

 

 

 

 

OnChip IDE First Channel

: Enabled

Onboard FDD Controller

: Enabled

 

 

OnChip IDE Second Channel

: Enabled

Onboard Serial Port 1

 

: 3F8/IRQ4

 

 

IDE HDD Block Mode

: Disabled

Onboard Serial Port 2

 

:

 

 

IDE Prefetch Mode

: Enabled

UART 2 Mode

 

:

 

 

IDE HDD Block Mode

: Auto

 

 

 

 

 

IDE Primary Master PIO

: Auto

 

 

 

 

 

IDE Primary Slave PIO

: Auto

Onboard Parallel Port

 

: 378/IRQ7

 

 

IDE Secondary Master PIO

: Auto

Parallel Port Mode

 

: SPP

 

 

IDE Secondary Slave PIO

: Auto

 

 

 

 

 

IDE Primary Master UDMA

: Auto

 

 

 

 

 

IDE Primary Slave UDMA

: Auto

 

 

 

 

 

IDE Secondary Master UDMA

: Auto

 

 

 

 

 

IDE Secondary Slave UDMA

: Auto

 

 

 

 

 

Init AGP Display First

: AGP

 

 

 

 

 

Onboard Audio Chip

: Enabled

 

 

 

 

 

 

 

ESC : Quit

Ç È Å : Select Item

 

 

 

 

F1 : Help

PU/PD/+/- : Modify

 

 

 

 

F5 : Old Values

(Shift) F2 : Color

 

 

 

 

F6 : Load BIOS Defaults

 

 

 

 

 

F7 : Load Setup Defaults

 

 

 

 

 

 

 

 

 

OnChip IDE First/Second Channel

The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately.

IDE Prefetch Mode

This field allows your hard disk to prefetch the next read and initiate the next process.

IDE HDD Block Mode

This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive.

IDE Primary/Secondary Master/Slave PIO

These fields allow your system hard disk controller to work faster. Rather than have the BIOS issue a series of commands that transfer to or from the disk drive, PIO (Programmed Input/Output) allows the BIOS to communicate with the controller and CPU directly.

The system supports five modes, numbered from 0 (default) to 4, which primarily differ in timing. When Auto is selected, the BIOS will select the best available mode.

60

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

IDE Primary/Secondary Master/Slave UDMA

These fields allow your system to improve disk I/O throughput to 33Mb/sec with the Ultra DMA/33 feature. The options are Auto and

Disabled.

Init AGP Display First

This field allows the system to initialize first the VGA card in the AGP slot on the motherboard when system is turned on.

Onboard Audio Chip

Select Enabled to use the integrated audio chip on the motherboard.

Onboard FDD Controller

Select Enabled if your system has a floppy disk controller installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field. This option allows you to select the onboard FDD port.

Onboard Serial/Parallel Port

These fields allow you to select the onboard serial and parallel ports and their addresses. The default values for these ports are:

Serial Port 1

3F8/IRQ4

Serial Port 2

2F8/IRQ3

Parallel Port

378H/IRQ7

UART 2 Mode

This field determines the UART mode in your computer. The settings are

Normal, IrDA and ASKIR. The default value is Normal.

Parallel Port Mode

This field allows you to determine parallel port mode function.

SPP

Normal Printer Port

EPP

Enhanced Parallel Port

ECP

Extended Capabilities Port

CI5VGM User’s Manual

61

Chapter 3 BIOS Configuration

Supervisor / User Password

These two options set the system password. Supervisor Password sets a password that will be used to protect the system and Setup utility. User Password sets a password that will be used exclusively on the system. To specify a password, highlight the type you want and press <Enter>. The Enter Password: message prompts on the screen. Type the password, up to eight characters in length, and press <Enter>. The system confirms your password by asking you to type it again. After setting a password, the screen automatically returns to the main screen.

To disable a password, just press the <Enter> key when you are prompted to enter the password. A message will confirm the password to be disabled. Once the password is disabled, the system will boot and you can enter Setup freely.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

 

INTEGRATED PERIPHERALS

BIOS FEATURES SETUP

 

SUPERVISOR PASSWORD

CHIPSET FEATURES SETUP

 

USER PASSWORD

POWER MANAGEMENT SETUP

 

IDE HDD AUTO

DETECTION

 

PNP/PCI CONFIGURATION

HDD LOW LEVEL

FORMAT

 

Enter Password:

 

LOAD BIOS DEFAULTS

SAVE & EXIT SETUP

LOAD SETUP

DEFAULTS

EXIT WITHOUT

SAVING

ESC : Quit

Ç È Æ Å : Select Item

F10 : Save & Exit Setup

(Shift) F2 : Change Color

Change / Set / Disable Password

62

CI5VGM User’s Manual

Chapter 3 BIOS Configuration

IDE HDD Auto Detection

This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen.

ROM PCI/ISA BIOS

STANDARD CMOS SETUP

AWARD SOFTWARE, INC.

HARD DISKS

TYPE

SIZE

CYLS

HEAD PRECOMP LANDZ SECTOR

MODE

Primary Master:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select Primary Master Option (N=SKIP) : N

 

 

 

 

 

OPTIONS

TYPE

SIZE

CYLS

HEAD

PRECOMP

LANDZ

SECTOR

 

MODE

 

 

1 (Y)

0

0

0

 

0

0

0

0

NORMAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: Some OSes (like SCO-UNIX) must use ”NORMALfor installation

ESC: SKIP

Up to four IDE drives can be detected, with parameters for each appearing in sequence inside a box. To accept the displayed entries, press the “Y” key; to skip to the next drive, press the “N” key. If you accept the values, the parameters will appear listed beside the drive letter on the screen.

CI5VGM User’s Manual

63

Chapter 3 BIOS Configuration

Save & Exit Setup

This option allows you to determine whether or not to accept the modifications. If you type “Y”, you will quit the setup utility and save all changes into the CMOS memory. If you type “N”, you will return to Setup utility.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

 

INTEGRATED PERIPHERALS

BIOS FEATURES SETUP

 

SUPERVISOR PASSWORD

CHIPSET FEATURES SETUP

 

USER PASSWORD

 

 

 

 

DETECTION

POWER MANAGEMENT SETUP

 

IDE HDD AUTO

PNP/PCI CONFIGURATIONSave to CMOS andHDDExitLOW(Y/N)?LEVELN

FORMAT

LOAD BIOS DEFAULTS

 

SAVE & EXIT SETUP

LOAD SETUP

DEFAULTS

 

EXIT WITHOUT

SAVING

 

ESC : Quit

 

Ç È Æ Å : Select Item

F10 : Save & Exit Setup

 

(Shift) F2 : Change Color

Save Data to CMOS & Exit Setup

Exit Without Saving

Select this option to exit the Setup utility without saving the changes you have made in this session. Typing “Y” will quit the Setup utility without saving the modifications. Typing “N” will return you to Setup utility.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

 

INTEGRATED PERIPHERALS

BIOS FEATURES SETUP

 

SUPERVISOR PASSWORD

CHIPSET FEATURES SETUP

 

USER PASSWORD

 

 

 

 

DETECTION

POWER MANAGEMENT SETUP

 

IDE HDD AUTO

PNP/PCI CONFIGURATION

 

HDD LOW LEVEL

FORMAT

 

Quit Without Saving (Y/N)? N

 

LOAD BIOS DEFAULTS

 

SAVE & EXIT SETUP

LOAD SETUP

DEFAULTS

 

EXIT WITHOUT

SAVING

 

ESC : Quit

 

Ç È Æ Å : Select Item

F10 : Save & Exit Setup

 

(Shift) F2 : Change Color

Abandon all Data & Exit Setup

64

CI5VGM User’s Manual

Chapter 4 Audio Driver Installation Guide

4

Audio Driver

Installation Guide

This chapter describes the audio driver installation procedure for the onboard YAMAHA YMF715-S audio chip. The YMF715-S (OPL3-SA3) single audio chip integrates OPL3 and its DAC, 16bit Sigma-delta CODEC, MPU401 MIDI interface, joystick with timer, and a 3D enhanced controller.

For normal operations and to maximize the audio functions of the motherboard, follow the audio driver installation procedure below.

This chapter contains the following sections:

 

Installing The Audio Drivers For Windows 95 ..........................

66

Setting the 3D Function..............................................................

71

Using YAMAHA Software Wavetable for Windows 95............

73

Installing the Audio Drivers for Windows NT 4.0 .....................

74

CI5VGM User’s Manual

65

Chapter 4 Audio Driver Installation Guide

Installing the Audio Drivers for Windows 95

Step 1.

After installing Windows 95, insert the CD or audio drivers

 

floppy disk that comes with your motherboard in the CD-ROM or

 

floppy disk drive (labeled YAMAHA Audio YMF715 Windows

 

95 Drivers).

Step 2.

Click on Start Setting Control PanelSystem Device

 

Manager. Upon clicking on Other Devices, the figure below

 

appears. Remove OPL3-SAX Sound Board, and then click

 

Refresh.

66

CI5VGM User’s Manual

Chapter 4 Audio Driver Installation Guide

Step 3. When the figure below appears, press the Next to search for the driver.

Step 4. When the figure below appears, click Other Locations…, then type d:\sound\ya715\win95 or a:\ and click OK.

CI5VGM User’s Manual

67

Chapter 4 Audio Driver Installation Guide

Step 5. The Update Device Driver Wizard will find YAMAHA OPL3-SAx Sound System and show the following figure. Click

Finish.

Step 6. When the Opl3sa.drv on OPL3-SAx driver could not be found, type the driver location as d:\sound\ya715\win95 or a:\ as shown below. Click OK.

68

CI5VGM User’s Manual

Chapter 4 Audio Driver Installation Guide

Step 7. When file copying is done and the figure below appears, insert the Windows 95 CD into the CD-ROM, and then click OK.

Step 8. When the driver installation is finished, continue to install the YSTATION software. Press Start → Run, then type d:\Sound\YA715\Win95\ystation\setup or a:\ setup (The disk is labeled YAMAHA Audio Application for Windows 95), then press Enter. Refer to the figure below.

CI5VGM User’s Manual

69

Chapter 4 Audio Driver Installation Guide

Step 9. When the figure below appears, click Typical, and then continue the installation by following Install Wizard. It is recommended that the default settings assigned by the Install Wizard be applied during the first time installation.

70

CI5VGM User’s Manual

Chapter 4 Audio Driver Installation Guide

Setting the 3D Function

Step 1. Click Start in the task bar, and then select Settings. Click Control Panel.

CI5VGM User’s Manual

71

Chapter 4 Audio Driver Installation Guide

Step 2. Double click the OPL3-SAx Config icon.

Step 3. Move Ymersion slide bar to adjust the 3D effects.

72

CI5VGM User’s Manual

Chapter 4 Audio Driver Installation Guide

Using YAMAHA Software Wavetable for Windows 95

The audio driver includes the YAMAHA Soft GM software. After finishing the audio driver installation, you can use this software to change some settings for better MIDI sound quality.

Step 1. To switch to FM or Soft GM (Software Wavetable) MIDI generator on Windows 95, click Start in the task bar, and then select Settings. Click Control Panel.

CI5VGM User’s Manual

73

Chapter 4 Audio Driver Installation Guide

Step 2. In the Control Panel window, double click the Multimedia icon.

74

CI5VGM User’s Manual

Chapter 4 Audio Driver Installation Guide

Step 3. When the window below appears, choose the MIDI tab. Three items are shown.

These items are:

 

OPL3-SA FM Synthesizer

Select OPL3 FM synthesizer.

OPL3-SA MPU401

Select Hardware Wavetable.

OPL3-SA SoftSynth

Select Soft GM (S/W Wavetable).

Depending on which device you would like to select, point the mouse cursor to the device name and click it. Then click the OK button. The device is ready to be used.

NOTE: If you choose Soft GM in high quality mode despite the poor CPU power, sound might not be played smoothly. A Pentium- based system or faster is recommended to play the Soft GM in high quality mode.

You cannot record while playing MIDI files when you are using the software synthesizer.

CI5VGM User’s Manual

75

Chapter 4 Audio Driver Installation Guide

Installing the Audio Drivers for Windows NT 4.0

Step 1. Before installing the audio drivers for Windows NT 4.0, you must first install the file pnpisa.inf. This file can be found in the Windows NT 4.0 CD or the Service Pack3 CD. It is recommended that the file in the Service Pack3 CD be used. When the file has been found, select the file by clicking the mouse and then click the mouse right button. Click Install to start copying files into your system. When Windows NT prompts you to restart the computer, click Yes.

Step 2. Upon restarting, Windows NT will find the new hardware

OPL3-SAX. Select Driver from disk provided by hardware manufacturer. Insert the CD or floppy diskette labeled YAMAHA Audio YMF715 Windows NT 4.0 Drivers, then click OK.

Step 3. Type A:\ or D:\sound\ya715\winnt40 (if you are using floppy diskette or CD respectively), then click OK.

Step 4. Select OPL3-SA sound system (xxxxx), then click OK. (xxxxx) refers to the language that you are using.

Step 5. When the Resource window appears, click OK.

Step 6. When the Game Port window appears, select Windows NT default driver, then click OK.

Step 7. Click Yes when Windows NT prompts you to restart the computer.

76

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

5

VGA Driver

Installation Guide

This chapter describe the VGA driver installation procedure for the

 

onboard Trident 9520/25.

 

This chapter contains the following sections:

 

Installing Trident 9520/25 Drivers for Windows 95...................

78

Installing Trident 9520/25 Drivers for Windows 98...................

84

Installing Trident 9520/25 Drivers for Windows NT 4.0 ...........

96

CI5VGM User’s Manual

77

Chapter 5 VGA Driver Installation Guide

Installing Trident 9520/25 Drivers for Windows 95

Step 1. In the Windows 95 screen, click Start. Select Settings, then click the Control Panel icon.

78

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 2. Double click Display, then click Settings.

CI5VGM User’s Manual

79

Chapter 5 VGA Driver Installation Guide

Step 3. Click Advanced Properties, then click Change....

80

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 4. Click Have Disk .... If "D:" is your CDROM, type D:\VGA\Trid9520\WIN95 and click OK. If you are using the floppy disk labeled Trident 9520/25 VGA Driver Windows 95/98, type A:\ and click OK.

CI5VGM User’s Manual

81

Chapter 5 VGA Driver Installation Guide

Step 5. Select Trident Cyber 9520/25 PCI/AGP (VX.XX.XXXX.95), then click OK.

82

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 6. After the files are copied, click Close.

Step 7. Click Yes to restart your computer and for the new settings to

CI5VGM User’s Manual

83

Chapter 5 VGA Driver Installation Guide

Installing Trident 9520/25 Drivers for Windows 98

Step 1. Click Start. Select Settings, then click the Control Panel icon.

84

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 2. Double click Display.

CI5VGM User’s Manual

85

Chapter 5 VGA Driver Installation Guide

Step 3. Click Settings.

86

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 4. Click Advanced.

CI5VGM User’s Manual

87

Chapter 5 VGA Driver Installation Guide

Step 5. Click Adapter.

88

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 6. Click Change....

CI5VGM User’s Manual

89

Chapter 5 VGA Driver Installation Guide

Step 7. Click Next.

Step 8. Select Display a list of all the drivers in a specific location, so you can select the driver you want.

90

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 9. Click Have Disk ....

Step 10. If "D:" is your CDROM, type D:\VGA\Trid9520\WIN98, If you are using the floppy disk labeled Trident 9520/25 VGA Driver Windows 95/98, type A:\ and click OK.

CI5VGM User’s Manual

91

Chapter 5 VGA Driver Installation Guide

Step 11. Select Trident Cyber 9520/25 PCI/AGP(vx.xx.xxxx.98), then click OK.

Step 12. Click Next.

92

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 13. After the files are copied, click Finish.

CI5VGM User’s Manual

93

Chapter 5 VGA Driver Installation Guide

Step 12. Click Close.

94

CI5VGM User’s Manual

Chapter 5 VGA Driver Installation Guide

Step 13. Click Close.

Step 14. Click Yes to restart your computer and for the new settings to take effect.

CI5VGM User’s Manual

95

Chapter 5 VGA Driver Installation Guide

Installing Trident 9520/25 Drivers for Windows NT 4.0

IMPORTANT: You should install the Windows NT 4.0 Service Pack 3 first before installing the Trident 9520/25 VGA drivers. If you don't have the Windows NT 4.0 Service Pack 3, please contact your software vendor or download it from Microsoft's web site.

Step 1. Boot Windows NT 4.0.

Step 2. Double click the My Computer icon. Step 3. Double click the Control Panel icon. Step 4. Double click the Display icon.

Step 5. Click Change Display Type. Step 6. Click Change.

Step 7. Click Have Disk, then insert the diskette disk labeled Trident 9520/25 VGA Driver Windows NT4.0 or CD containing the

Trident 9520/25 VGA Windows NT 4.0 drivers to the floppy disk drive/CD-ROM drive, then type in A:\ (if you are using drive A) or type in D:\VGA\Trid9520\WINNT40 (if you are using drive D which is your CD-ROM drive), and press Enter.

Step 8. Select Trident Video Accelerator 3D Adapter [TW3001], then click OK.

Step 9. Click Yes to copy the drivers from the floppy disk/CD to the hard disk.

Step 10. When copying is done, click OK. Step 11. Click Close.

Step 12. Click OK.

Step 13. Windows NT 4.0 will prompt you to restart computer. Click OK to change the Windows NT configuration.

96

CI5VGM User’s Manual