Hyundai Q421S, Q421H, Q501 User Manual

4.4 Mb
Loading...

FCC Information

User Instructions

The Federal Communications Commission Radio Frequency Interference Statement includes thefollowing warning :

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital devicepursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particularinstallation.

If this equipment does cause harmful interference to radio or television receptions, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.

Consult the dealer or an experienced radio/TV technician for assistance.

User Information

Changes or modifications not expressly approved by the party responsible for compliance could voidthe user’s authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.

HYUNDAI Digital PDP TV

Important Tip

Image Retention Effect (Image Sticking)

1.

Cause :

-

Image Retention Effect may come from displaying a still picture in certain period of time with at a

 

certain area continuously, as the feature of PDP panel. This is caused due to brightness degradation.

 

Many PDP manufacturers are trying to overcome this limitation.

2.

Prevention

-To avoid this matter, use the product after reducing brightness and contrast, especially when a still image is displaying for a long time. (Contrast 50/Brightness 50 - See 30 page)

Once image retention occurs, use the mode that displays more motion pictures. It will help reduce this matter.

3. Solution

-The temporary image sticking would decrease with displaying Full-White pattern during 10 hours.

*The permanent image sticking could not take off under the latest technology.

This method may be used to eliminate a temporary retained image that occurs after displaying a still image for a certain period of time. Since it may take several minutes to several hours to remove image sticking, it is recommendable to display motion pictures during 2~3 minutes every hour when keeping displaying a still image. As image sticking is influenced by the brightness of a still image being displayed and its display time, it is recommended that you reduce the brightness of the screen when displaying a still image for a long time.

* Image Sticking does not come under the warranty.

Image Sticking Precaution

When watching a still Image within motion pictures and Panorama/Wide/4:3 screen

Panorama, Wide, 4:3 screen

Box still image

1. Note :

-When the central area of the screen and the screen edges are fixed, the different brightness level of the edges may cause image retention on the edges when watching for a long time

-This phenomenon is the same matter to other LCD manufacturers. Please do not watch a still image for a long time.

-If you watch a still image for a long time, this may damage your TV.

* This matter does not come under the warranty.

HYUNDAI Digital PDP TV

Features

Integrated HDTV

An HDTV has a built-in ATSC digital tuner.

It does not need a separate set-top box to receive over the-air & Cable DTV signal.

Dual Scan/Multi-Viewing

You can program analog TV broadcasting and digital TV broadcasting automatically at the same time for multi-viewing.

A Wide Array of Screen Settings

You can choose different screen settings depending on the type of program you are watching or the surrounding conditions (the outside weather conditions). You can switch among Standard, Dynamic, Movie, and Mild options or you can configure the screen settings for yourself.

A Wide Array of Sound Settings

You can choose an optimal sound setting for the type of program you are watching.

You can switch among Standard, News, Music, and Sport options or you can configure the sound settings for yourself.

TV Program Reservation

If you reserve a digital TV program you are going to watch, the channel you are currently watching is automatically switched to the reserved channel.

Favorite Channel Memory

You can memorize the channels you are watching frequently.

SRS TrueSurround XT

You can enjoy dynamic and surround sound with ordinary speakers.

Dolby-Digital

When receiving digital broadcast signal, you can enjoy dynamic and surround sound with two ordinary speakers just like Dolby 5.1.

A Variety of Aspect Ratios

You can adjust the screen size at your preference.

Auto On/Off Function

This function allows you to turn on or off your TV at the preset time.

Game Prevention Function

This function is designed to prevent a VCR or game player from being connected to the TV.

Table of Contents

General Information

 

Safety Precaution ................................................................

5

Contents of the Package .......................................................

9

Products Sold Separately ......................................................

9

How to Install Desktop Stand ..............................................

10

How to use Speakers .........................................................

11

Parts Names and Functions ................................................

13

Remote Control ...................................................................

15

Connections

 

How to Watch Both Analog and Digital Broadcasts

 

with a Single Antenna .........................................................

17

How to Watch Both Analog and Digital Broadcasts

 

with Two Antennas .............................................................

18

Before Connecting the Video/Audio Connections to

 

External Devices... .............................................................19

How to Connect a VCR/Cable Receiver ................................

20

How to Connect a DTV Receiver or DVD Player ....................

21

How to Connect a Camcorder/Game Player .........................

22

How to Connect to a PC ......................................................

23

HDMI Connection ................................................................

25

How to Connect an External Visual Device ...........................

27

How to Use Digital Sound ....................................................

28

Picture Setup

 

How to Select the Picture Mode ..........................................

29

How to Set the Desired Picture ...........................................

30

How to Adjust the Color Temperature of the Screen ............

31

How to Select the Aspect Ratio ...........................................

32

How to Watch the PIP .........................................................

34

How to Set the INPUT for the Sub-Picture ...........................

35

How to Reduce Noise ..........................................................

37

Sound Setup

 

How to Select the Audio Mode ............................................

38

How to Adjust the Desired Audio Mode ..............................

39

How to Use the Automatic Volume Control ..........................

40

How to Select MTS(Multi-Channel Sound) ...........................

41

HYUNDAI Digital PDP TV

How to Listen to SRS TruSurround XT (Surround) ................

42

How to Set the Output of Subwoofer ...................................

43

How to Set the Speaker Output ...........................................

44

How to Set the Digital Audio Output ....................................

45

How to Set Audio Language ................................................

46

Channel Setup

 

How to Store Channels Automatically ..................................

47

How to Add/Erase Channels Manually .................................

48

How to Set Favorite Channels .............................................

49

How to Fine Tune Channel Reception ..................................

50

How to the LNA (Low-Noise-Amplifier) Feature ...................

51

Function Setup

 

How to Choose Your Language ...........................................

52

How to Set Clock, On/Off Time, Sleep Time ........................

53

How to Set the Geometry in PC Mode ..................................

55

How to Set Key Lock ...........................................................

56

How To Set Block Program .................................................

58

How to View Closed Captions ..............................................

60

Using the pixel Shift / Full White ..........................................

62

DTV Setup

 

How to Use the Current Channel Guide ..............................

63

How to Reserve TV Programs Using the Total Channel Guide ....

63

How to Use TV Program Reservation ...................................

64

How to Check or Cancel a Scheduled TV Program ...............

65

Appendix

 

How to Use an External Device Using the Remote Control ...

66

Glossary .............................................................................

69

Troubleshooting ..................................................................

72

Care and Cleaning ..............................................................

74

Product Specifications ........................................................

75

GENERAL INFORMATION

Safety Precaution

The contents of this section are provided for the safety of users and their property. Please read the instructions carefully before using.

Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National Electrical Code Instruction

Do not use or store a flammable spray or inflammable things near the TV.

- They may cause explosion or fire.

Do not install the TV in a bookshelf, closet, or a place with poor air circulation.

- Fire may be caused due to the rise of internal temperature.

Do not connect multiple electrical appliances to a single outlet.

-It may cause a fire due to overheating from the outlet.

Make sure to remove the speakers before moving the TV with speakers mounted on it.

- When the speakers are detached from the unit while carrying it, this may cause damage to the unit or personal injury.

Any necessary action such as making the antenna cable loop at the entrance of the building should be taken to prevent rainwater on the outdoor antenna cable from possibly running indoor.

-If raindrop gets into the TV, it may cause a fire or an electric shock.

5

HYUNDAI Digital PDP TV

If there is a persistent accumulation

Do not use a damaged power cord

of dusts or water on the plug, please

or plug, or loose outlet.

make sure to wipe it off using a dry

- It may cause electric shock or fire.

cloth.

 

- It may cause a fire or an electric shock.

 

Firmly plug in the power cord so that it does not pull out.

- An unstable connection may cause fire.

Do not install in a place where there is oil, smoke, excessive humidity, or where water may be sprinkled on it.

- This may cause electric shock or fire.

Do not put a water bowl, vase, candle, bug repellant smoke, cigarette, plants, or heavy thing on the TV.

- It may cause electric shock or fire and also heavy things may cause injury when they fall.

Do not install on an unstable place or small support.

-This may cause the TV to fall, resulting in serious injury especially to children.

Never attempt to open, fix, or modify your TV.

-When there is a need for fixing, call a service center. Fire or electric shock may be caused.

When the TV produces abnormal noise, burning smell, or smoke, unplug the TV immediately and call a service center.

- Electric shock or fire may be caused.

Do not put a metallic object like chopstick, wire, or puncher or inflammables like paper or a match in a vent, headphone jack, or AV jacks of the TV.

- Electric shock or fire may be caused.

INFORMATION GENERAL

6

GENERAL INFORMATION

Safety Precaution ......................................

Continued from previous page

The contents of this section are provided for the safety of users and their property.

Please read the instructions carefully before using.

Do not block ventilating slits with a table cloth.

- Blocking the ventilation slits may produce internal heat increase, resulting in a fire.

Please avoid touching the panel at the rear of

Do not place any heat sources such as

TV as it is producing high temperature.

- Direct contact with the hot surface may

radiators and heat registers, etc. near the TV.

cause physical burns.

- It may cause a fire.

Do not place toys and cookies, etc. on the TV, which may attract children’s attention.

- This may cause the TV to fall, resulting in serious injury.

Do not allow children to climb or play on the TV.

-This may cause the TV to fall resulting in serious injury.

When cleaning the TV, make sure to disconnect the power plug and use a dry, soft cloth for a cleanup.

-Please avoid using chemicals such as wax, benzene, alcohol, thinner, mosquito spray, air freshener, lubricant or synthetic detergent.

Unplug when you do not use your TV for a long time.

-If dust is stacked on the TV, electric shock or fire may be caused from heat, fire, or

deterioration of insulation.

When moving the TV, two or more people are advised to carry it.

- This may cause damage to the unit or personal injury.

Never touch the power plug or outlet with wet hands.

- This may cause electric shock.

7

HYUNDAI Digital PDP TV

Unplug the product during lightning or thunderstorms and never touch the antenna cable.

- It may cause a fire or an electric shock.

 

Keep the remote control batteries out of

Do not install the product on the floor.

sight and out reach of children.

- This may cause the TV to fall resulting in

- If your child swallows a battery, see your

serious injury.

doctor immediately.

When replacing batteries, make sure to match the batteries to the (+) and (-) marks in the battery compartment.

- Mismatching of polarities may result in internal damage to batteries, fire due to leakage or contamination.

 

 

 

In the event of damaging or dropping the

 

 

Always use the standard batteries and avoid

product, switch off the power and remove

 

 

the plug.

 

 

using old batteries together with new ones.

 

 

- Using a damaged product may cause an

 

 

- Otherwise it may result in internal damage

 

 

electric shock or a fire.

 

 

to batteries, fire due to leakage or

 

 

- Contact your local service center.

 

 

contamination.

 

 

 

 

 

 

 

Before moving the product, ensure to switch off the power and unplug all the electrical cords and the external connection cords such as an antenna cable and other source connections, etc.

-Electrical cords may be damaged, resulting in a fire or an electrical shock.

Consult a service center or customer service for inside cleaning about once a year.

- When dust is piled inside the TV for a long time, fire or malfunction may be caused.

Ensure the power cord doesn’t trail across any hot objects like a heater.

- This may cause a fire or an electric shock.

INFORMATION GENERAL

8

GENERAL INFORMATION

Contents of the Package

hen opening the package, please ensure to check the following accessories provided.

Antenna Cable

Power Cord

Remote Control &

User's Guide

(coaxial cable)

 

2 batteries (1.5V AAA)

 

Products Sold Separately

If you want to purchase separately sold products, consult a service center, electronics shops, or parts seller.

Component(Y, Pb, Pr) cable Composite(Video & Audio) cable

DVI PC video(digital) cable

HDMI cable

 

 

S-video cable

PC signal cable

Audio Cable (DIV/DVD)

Audio Cable (PC)

 

 

Desk type stand

speaker

Desk type speaker

 

 

stand

Ceil mounting frame

Adjustable wall

 

mounting frame

9

HYUNDAI Digital PDP TV

How To Install Desktop Stand

1.

Place the TV body on a flat desk or a shelf. Clean the surface of the desk or the shelf in order to prevent scratch on the

GENERAL

 

product.

 

 

2.

Align the stand with TV body below and fasten the stand bars using 4 fixing screws.

INFORMATION

3.

After the assembly is over, stand the assembled product at a desired place.

 

Fixing screws

Desk type stand

WARNING Warning : Do not install at an unstable place or on a small support.

(When a child plays around the product and touch it, TV may fall and injure the child.)

10

GENERAL INFORMATION

How To Use Speakers (Standing Type)

Parts configuration chart

2 Speakers (left and right)

4 brackets

16 fixing screws

2 sets of speaker cables

 

 

 

(left and right)

Connect speaker cables between terminals on the rear of speakers with speaker connection terminals on the rear of TV. (Connect cables and terminals in the same color)

WARNING

Do not move the product holding the speakers. Always use handles on the TV.

(Brackets connecting TV and speakers may be damaged.)

11

HYUNDAI Digital PDP TV

How To Use Speakers (Desk Type)

Parts configuration chart

INFORMATION GENERAL

2 Speakers (left and right)

2 Speaker-stands

8 fixing screws

2 sets of speaker cables

 

(left and right)

 

(left and right)

Assembly and Connect method

Insert speaker-stands in the groove

Upright

and place them on the

on the bottom of speakers and

desired place left and right of TV.

fasten them using fixing screws.

(Left and right side each)

(Left and right side each)

 

 

Connect speaker cables between terminals on the rear of speakers and speaker connection terminals on the rear of TV. (Connect cables and terminals with the same color)

12

GENERAL INFORMATION

Parts Names and Functions

Front View

* This product image may be a bit different from the actual product.

Power button

Use this button to turn on or off the TV.

Volume buttons

Use these buttons to adjust sound levels. These buttons also serve as the cursors of Select/Adjust in Menu mode.

Channel buttons

Use these buttons to change channels. These buttons also serve as the cursors of Down and Up buttons in Menu mode.

Select button

Use this button to select each item from the menu mode.

Menu button

Use this button to display or exit from the menu mode.

Source button

Use this button to switch among inputs connected to the TV.

Remote sensor and power LED.

-Point the remote control toward LED.

-It displays standby or operation status.

-Power Indicator Status -

Indicator

Status

Red

Standby

Green

Power on

 

 

13

HYUNDAI Digital PDP TV

Rear View

* This product image may be a bit different from the actual product.

HDMI (or DVI) Video input terminal

D-SUB input terminal

DVI/D-SUB Audio input terminal

Subwoofer output terminal

When producing bass, connect the cable to the woofer with *AMP.

Component 2 Video input terminal

Component 2 Audio input terminal

Component 1 Video input terminal

Component 1 Audio input terminal

S-Video input terminal

Video input terminal

S-Video/Video Audio input terminal

RS-232 input terminal

Connect to the RS-232 terminal of a PC to check its service.

Monitor Video output terminal

Monitor Audio output terminal

Antenna1(Analog / DTV)input terminal

Antenna2(DTV)input terminal Digital Audio output terminal for coaxial cable

SPDIF Optical audio output terminal

Power (AC) input terminal

Connect the power cord to this terminal.

Power switch

Use this switch to turn on/off power

Stand assembly

Speaker terminal

Speaker assembly

Screw hole for fixing on a wall Carrying handles

INFORMATION GENERAL

14

Remote Control

GENERAL INFORMATION

31

1.POWER/STANDBY

2.MUTE/Magic

This button is also used when setting up to use other external

device.

3. PIP FUNCTIONS

-PIP

:Use this button for PIP On/Off.

-SOURCE

:Use this button to select the input source of sub-picture.

-SIZE

:Use this button to select the size of sub-picture.

-SWAP

:Use this button to swap main and sub-picture.

-POSITION

:Use this button to select the position of sub-picture.

4. A/D+

Use this button to switch analog input signal to digital signal.

5. Previous Channel

Use this button to return to the previous channel.

6.Other external device selection ( 66P)

7.MENU SELECTION

Use this button to select menu items.

8. LEFT/RIGHT MOVE/ADJUST

Use these buttons to move between menu items or to adjust

each item.

9. MENU

Use this button to call the OSD to the screen.

10. EXIT

Use this button to end the OSD.

11. CHANNEL SELECTION

Use this button to select the channel.

12-13. SUB-PICTURE CHANNEL SELECTION

14. PC AUTO

Use this button to automatically adjust the screen in PC Mode.

15. DTV-GUIDE

Use this button to see digital broadcast information.

16. SRS

Use this button to select 3D surround sound.

17. SAP

Use this button to listen in a foreign language or in Stereo

Mode.

15

HYUNDAI Digital PDP TV

18.PICTURE MODE

19.SOUND MODE

20.BOOK-MARK

Use this button to select/deselect your frequently-used channel.

21.CC(Closed Caption)

22.FAVORITE

Use this button when watching your favorite channel.

23. ADD/ERASE

Use this button to add or erase channels.

24. INFOMATION

Use this button to display resolution or various program information.

25. SOURCE

Use this button to select External Input

26.VOLUME

27.FREEZE

28.SLEEP

29.ASPECT RATIO

Use this button to change the picture size.

30.NUMERIC KEYS

31.Use this buttons to use other manufacturer’s DVD or VCR.

How to Insert Batteries in Remote Control

INFORMATION GENERAL

Press and hold part and push

Insert batteries with proper

Use the remote control with cover

to open cover.

polarities of +and -.

closed.

* Battery type :1.5V/AAA

 

 

16

CONNECTIONS

How to Watch Both Analog and Digital Broadcasts with a Single Antenna

You can watch both analog and digital broadcasts by connecting a single antenna.

Connection Method

Make sure that the antenna cable is connected to ANT 1 (ATV/DTV).

-Antenna or Cable service without a cable box connections

-For optimum picture quality, adjust antenna direction if need,

VHF Antenna

UHF Antenna

-When inserting a 75 ohm coaxial cable into the input connection, ensure the wire tip not to bend.

-If you experience poor signal reception, we recommend you purchase a signal amplifier for better picture quality.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

While watching digital broadcast, you can switch a digital signal to an analog signal by pressing the

button.

17

HYUNDAI Digital PDP TV

How to Watch Both Analog and Digital Broadcasts with Two Antennas

Connection Method

Connect an analog antenna to ANT 1 terminal for analog source and a digital antenna to ANT 2 terminal for digital source. Please ensure to connect an antenna to a correct terminal. (If you connect an analog antenna cable to ANT 2, you cannot watch TV program.)

Digital TV antenna cable

Analog TV antenna cable

-When inserting a 75 ohm coaxial cable into the input connection, ensure the wire tip not to bend.

-If you experience poor signal reception, we recommend you purchase a signal amplifier for better picture quality.

CONNECTIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

While watching analog broadcast, you can switch an analog signal to a digital signal by pressing the

button.

18

CONNECTIONS

Before Connecting the Video/Audio Connections to External Devices...

Please make sure to read the following information on connection to enjoy best picture quality.

Video/Audio connectors

Types of video/audio cable :

HDMI / DVI-D 15-Pin D-Sub COMPONENT S-VIDEO COMPOSITE

Best picture quality is displayed in the following order.

The superior picture quality starts from the far left side.

ensure to read the connecting device’s manual. The location or the number may be different depending on its model.

to the output of DVD, cable receiver or satellite receiver. Connecting a may result in a message, “Unknown Signal”.

connections are made. If power is given before connections completed, this

with the terminal. to be connected.

19

HYUNDAI Digital PDP TV

How to Connect a VCR/Cable Receiver

Connection Method

1

Connect the Video cable or S-Video cable between Video/S-Video output terminal of VCR or Cable receiver and

Video/S-Video input terminal of TV. (Connect the jacks to terminals in the same color.)

2

Connect the Audio cable (Left: white, Right: red) between Audio output terminal of VCR or cable receiver and

Audio input terminal of TV. (Connect the jacks to terminals in the same color.)

Video/Cable receiver

Audio cable

Video cable or

S-Video Cable

How to Watch

1

Turn on TV to press

on remote control.

 

2

Press

to move to Video or S-Video and press

to select.

For more information, read the user’s guide of VCR or cable receiver.

To enjoy better picture quality, use the S-Video cable rather than the composite cable.

CONNECTIONS

20

CONNECTIONS

How to Connect a DTV Receiver or DVD Player

Connection Method

1 Connect the Video cable (Y, Pb, Pr) between output terminals (Y, Pb, Pr) of DTV receiver or DVD player and the

2

DTV receiver / DVD Player

Video (Y, Pb, Pr) cable

Audio cable

1

2

-Output terminal mark (Y, Pb, and Pr) of DVD player may be indicated as Y, B-Y, R-Y/Y-Cb-Cr /Y-Pb-Pr according to the type of DVD player models.

-If your DVD player or Set Top Box supports HDMI (or DVI) /D-SUB, see Connecting to a PC (page 25) for connection. You can enjoy more clear picture quality.

21

HYUNDAI Digital PDP TV

How to Connect a Camcorder/Game Player

Connection Method

1

 

Connect the Video/S-Video cable between Video/S-Video output terminal of Camcorder/Game player and

 

Video/S-Video input terminal of TV. (Connect cables and terminal in the same colors.)

 

2

 

Connect the Audio cable (Left-white, Right-red) between Audio output terminal of Camcorder/Game player

 

and Audio input terminal of TV. (Connect the jacks to terminals in the same color.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Camcorder

Game Player

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio cable

Video cable or

S-Video Cable

How to Watch

1

Turn on TV and press

on remote control.

 

2

Press

to move Video or S-Video and press

to select.

For more information, read the user’s guide of Game player or Camcorder.

CONNECTIONS

22

CONNECTIONS

How to Connect to a PC

Connection Method

1

TV.Connect the PC signal cable (15-pin D-sub) between the output terminal of PC and the D-sub input terminal of

2

Connect the Audio cable between Audio output terminal of PC and Audio input terminal for PC on the rear of

TV. (Connect the jacks to terminals in the same

color.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Cable

or

D-SUB cable

When Using as a PC Monitor

1

2

Turn on TV and press on remote control.

Press

to move to PC or HDMI (or DVI) and then press

to select.

-If you use the HDMI (or DVI) connection, you can enjoy better picture quality.

-This product supports Plug-and-Play function.

-We recommend the above method if the DVD player or set top box supports DTV signal with HDMI (or DVI)/ D-Sub (15 pin) cable for the better picture quality.

-If you input an unsupported resolution in PC or HDMI (or DVI) mode, the screen won’t be displayed properly.

23

HYUNDAI Digital PDP TV

Resolutions Supported in PC

Resolution

Horizontal frequency

Vertical frequency

 

 

 

 

 

 

31.47

70.09

 

640 x 350

 

 

 

37.86

85.08

CONNECTIONS

 

 

 

 

 

31.47

59.94

 

 

 

 

 

 

 

37.86

72.80

 

640 x 480

 

 

 

37.50

75.00

 

 

 

 

 

 

 

 

43.27

85.01

 

 

 

 

 

720 x 400

31.47

70.08

 

 

 

 

 

 

37.88

60.32

 

 

 

 

 

 

48.08

72.18

 

800 x 600

 

 

 

46.88

75.00

 

 

 

 

 

 

 

 

53.67

85.06

 

 

 

 

 

832 x 624

49.72

74.55

 

 

 

 

 

 

48.36

60.00

 

1024 x 768

 

 

 

60.02

75.03

 

 

 

 

 

 

68.68

85.00

 

 

 

 

 

24

CONNECTIONS

HDMI Connection - For HDMI Model only

HDMI *1 (High Definition Multi media Interface) is the first all digital consumer electronics A/V interface that supportsuncompressed standard. The HDMI terminal supports both video and audio information.To the HDMI*1 input terminal, you can connect an EIA/CEA-861/861B*2 compliant consumer electronic device, such asa Set Top Box or DVD player with HDMI or DVI output terminal.Input a High-bandwidth Digital Content Protection (HDCP) high-definition picture source to this HDMI terminal, so youcan display the high-definition pictures on this TV in the digital form.

HDMI

DVD Player

Set Top Box

If the external device has DVI output only, use a DVI to HDMI adapter *3 cable to connect to the HDMI terminal.

HDMI Cable

Compatible VIDEO Signal

Resolution

No. of dots(HXV)

Vertical scanning frequency(Hz)

 

 

 

1080i

1920 X 1080i

59.94/60

 

 

 

 

720 X 480p

59.94/60

480p

 

 

640 X 480p

59.94/60

 

 

 

 

720p

1280 X 720p

59.94/60

 

 

 

 

 

 

This input terminal is not intended for use with computers.

25

HYUNDAI Digital PDP TV

CONNECTIONS

1

2

-*1 HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMILicensing LLC.

-*2 EIA/CEA-861/861B profiles compliance covers profiles for transmission of uncompressed digital video includinghigh bandwidth digital content protection.

-*3 HDMI-DVI conversion cable (TY-SCHO3DH): available on Panasonic Website (www.panasonic.com). Consult yourconsumer electronics dealer for availability details.

26

CONNECTIONS

How to Connect an External Visual Device

You can connect your TV to other visual device to watch two TV programs at the same time.

Connection Method

1

Connect the Composite Video cable between Video input terminals of an external device and the Video output

terminals for Video on the rear of TV.

 

(Connect the jacks to terminals in the same color.)

2

Connect the Audio cable between Audio input terminal (Left-white, Right-red) of an external device and Audio

output terminal for Video on the rear of TV. (Connect the jacks and terminals in the same color.)

3

For more information, read the user’s guide of an external device.

External Visual Device

Audio Cable

Video Cable

Video and Audio outputs are available only when watching an Analog TV, Digital TV or Video. This is not supported in the Input Mode of Component, HDMI (or DVI) /D-SUB or S-Video.

27

HYUNDAI Digital PDP TV

How to Use Digital Sound

Connection Method

1

Connect the coaxial cable or optical cable to the digital audio output terminal for coaxial cable or SPDIF

 

optical digital audio output terminal on the rear of TV.

2

Deselect Speaker Output from the Sound Menu and select Digital Sound Output. (See page 44~45)

3

For more information, read the user’s guide of the external sound device.

 

Do not look into directly the beam with the optical port. Doing so may damage your eyesight.

CONNECTIONS

Amplifier with Built-in Dolby Digital AC3

Digital Audio Output is available when watching a digital TV program.

28

PICTURE

How to Select the Picture Mode

Users can automatically adjust the picture mode according to the input mode.

 

Press Menu button.

 

Menu items appear on the screen.

1

Press

button to select

“MODE” is selected.

 

2

Whenever you press Left or Right button, the mode

changes in following order.

Standard Dynamic Movie Mild

 

User 1

User 2

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

STANDARD : Most video contents are appropriate to this mode.

DYNAMIC : Clear display

MOVIE : When watching a movie

MILD : Soft display.

CUSTOM : When the user wants to directly set the values See the next page

How to Directly Select Picture Mode : Press MODE. button.

-When the input mode is Analog TV, Digital TV, Video, S-Video, Component 1 & 2, users can select Standard Dynamic Movie Mild User 1/2 .

-When the input mode is PC, HDMI (or DVI), users can select Standard Low (Character Mode) High (Movie) User 1/2 .

-The adjustment menu may be different depending on the input mode.

-The adjustment of Contrast, Brightness, Sharpness, Color and Tint is allowed only in the Custom mode.

29

HYUNDAI Digital PDP TV

How to Set the Desired Picture

Users can manually adjust their desired picture.

 

Press Menu button.

 

 

Menu items appear on the screen.

1

Press

button to select

.

 

 

 

Press Left or Right button to choose “User 1/2”.

2

Press Left and Right buttons to move to Custom .

 

3

Press button to select Custom .

 

 

Picture Adjust menu items appear.

4

Press Up and Down buttons to move.

Press Left and Right buttons to adjust.

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

CONTRAST : Adjust the brightness and darkness of object and background.

BRIGHTNESS : Adjust the brightness of the entire picture.

SHARPNESS : Adjust clarity of outline of objects.

COLOR : Adjust colors into deeper or lighter colors.

TINT : Adjust colors naturally.

SHARPNESS, COLOR, TINT are not applied to PC and HDMI (or DVI) modes.

PICTURE

30

PICTURE

How to Adjust the Color Temperature of the Screen

Users can manually adjust their desired color temperature.

Press Menu button.

Menu items appear on the screen.

1

Press button to select

.

2

Press Up and Down buttons to move to “COLOR TEMP”.

 

 

3

Whenever you press Left or Right button,

the mode changes in following order.

 

 

Standard Warm 1

Warm 2 Cool 1 Cool 2

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears

STANDARD : General color of the picture

COOL 1, 2 : Cool color in the background with a bluish tint

WARM 1, 2 : Warm color in the background with a reddish tint

31

HYUNDAI Digital PDP TV

How to Select the Aspect Ratio

Users can manually adjust the size of the screen.

Press Menu button.

Menu items appear on the screen.

1

Press

button to select

.

2

Press Up and Down buttons to move to ASPECT RATIO .

 

 

 

3

Whenever you press Left or Right button,

the mode changes in following order.

 

 

Wide

Normal Panorama Zoom 1 Zoom 2

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

PICTURE

32

PICTURE

AUTO (This is applied in digital broadcasting input mode only.)

The screen size automaticaly changes according to a signal source received (General broadcast 4:3, Wide broadcast 16:9)

General broadcast picture is adjusted to 16:9.

Normal

Panorama

ZOOM 1

ZOOM 2

33

HYUNDAI Digital PDP TV

How to Watch the PIP

This function allows you to watch the PIP or DW mode.

 

Press Menu button.

 

 

Menu items appear on the screen.

1

Press

button to select

.

2

Press Up and Down buttons to move to PIP.

3

Press Left and Right buttons to select PIP.

 

 

The PIP Menu appears.

 

Whenever you press Left or Right button, 4 the mode changes in following order.

PIP SMALL PIP MIDDLE PIP LARGE DW 1 DW 2 OFF

After setting Mode, go to STEP 5 if you need to set the

SOURCE for Sub-picture.

<PIP Small>

 

<PIP Middle>

<PIP Large>

 

 

 

 

 

 

 

 

<DW 1 >

<DW 2 >

Continued on the next page

PICTURE

34

PICTURE

How to Set the INPUT for the Sub-Picture

This function is available only in the PIP mode.

5

Press Up and Down buttons to move to

SOURCE

 

 

 

6

Press

Left and Right buttons to select

SOURCE .

The list of sub-picture sources appears.

 

 

 

7

Press Up and Down buttons to move to the sub-picture

source you want.

 

8

Press

Press button to select source.

 

 

 

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

You can set the PIP mode quickly using the remote control.

How to Select the PIP : Press the button.

Whenever you press this button, the PIP mode is selected or deselected.

How to Select the Size of Sub-picture : Press the button.

Whenever you press this button, the size of the Sub-picture changes.

How to Select the INPUT : Press the button.

Press the buttons to select the INPUT and then select .

How to Switch the PIP to Sub-picture : Press the button.

Whenever you press this button, the Main picture and Sub-picture are switched each other.

35

HYUNDAI Digital PDP TV

How to Set the channel of the Sub-picture Channel : Press the button.

This is applied only for TV when the sub-picture is displayed.

How to Change the Position of the Sub-picture : Press the button.

Bottom Right Corner Bottom Left Corner Left Top Corner Right Top Corner

The same input mode cannot be selected for the main picture and sub-picture.

PICTURE

Sub

PC

HDMI(or DVI)

DTV

Component 1

Component 2

Analog TV

Video

S-Video

Main

PC

X

X

X

X

X

O

O

O

 

 

 

 

 

 

 

 

 

HDMI(or DVI)

X

X

X

X

X

O

O

O

 

 

 

 

 

 

 

 

 

DTV

X

X

X

X

X

O

O

O

 

 

 

 

 

 

 

 

 

Component 1

X

X

X

X

X

O

O

O

 

 

 

 

 

 

 

 

 

Component 2

X

X

X

X

X

O

O

O

 

 

 

 

 

 

 

 

 

Analog TV

O

O

O

O

O

X

O

O

 

 

 

 

 

 

 

 

 

Video

O

O

O

O

O

O

X

O

 

 

 

 

 

 

 

 

 

S-Video

O

O

O

O

O

O

O

X

 

 

 

 

 

 

 

 

 

36

PICTURE

How to Noise Reduct

Press Menu button.

Menu items appear on the screen.

1

Press

button to select

.

2

Press Up and Down buttons to move to NOISE REDUCT .

 

 

 

3

Whenever you press Left or Right button,

the mode changes in following order.

 

 

LOW

HIGH Off

 

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

37

HYUNDAI Digital PDP TV

How to Select the Audio Mode

Users can adjust sound mode automatically as they want.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

MODE is selected.

 

 

 

 

 

3

Whenever you press Left or Right button,

 

the mode changes in following order.

 

 

 

 

Standard News Music

Sports

User

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

STANDARD : General sound mode. This fits most audio contents.

NEWS : For enjoying clear sound.

MUSIC : For enjoying original sound.

SPORTS : For enjoying vivid sound.

CUSOTM : When the user wants to set the value. See the next page

SOUND

38

SOUND

How to Adjust the Desired Audio Mode

Users can adjust sound mode automatically as they want.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

 

 

 

 

Press Left and Right buttons to select

USER .

3

Press Up and Down buttons to move to

CUSTOM .

 

4

Press Left and Right buttons to select

CUSTOM .

SOUND CUSTOM menu appears.

 

 

5

Move between the items listed using UP or Down button.

Adjust the level of the item selected using Left or Right button.

Press MENU button after the setting is done, and Menu goes to the previous menu. If the EXIT button is pressed, the menu disappears.

VOLUME : Adjusts the volume.

BASS: Adjusts the range size of low sound.

TREBLE: Adjusts the range size of high sound.

BALANCE : Adjusts the balance of left and right speakers.

39

HYUNDAI Digital PDP TV

How to Use the Automatic Volume Control

With this Automatic Volume Level Control, everything you watch will always maintain the volume level that you decide.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

 

 

 

3

Press Left and Right buttons to set to

ON/OFF .

 

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

SOUND

40

SOUND

How to Select MTS(Multi-Channel Sound)

Depending on the particaular program being brodcast, you can select stereo, mono, or a Separate Audio Program. (SAP audio is usually a foreign-language translation. Somtimes SAP has unrelated information like news or weathter.)

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press

button to select

.

 

 

 

 

 

3

Press Up and Down buttons to move to

 

 

 

 

“MTS”.

 

 

 

4

Press Left and Right buttons,

 

 

Repeatedly to select “MONO”, “STEREO” or “SAP”.

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

If you also press the MTS button on remote control unit under other mode than TV mode, the current setting information is displayed. If you press the MTS button twice, the mode shifts MONO STEREO in order.

41

HYUNDAI Digital PDP TV

How to Listen to SRS TruSurround XT (Surround)

Users can enjoy spectacular 3D sound.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

 

 

 

3

Press Up and Down buttons to move to

SURROUND .

 

4

Press Left and Right buttons to set to

ON/OFF .

SOUND

is a trademark of SRS Labs, Inc.

TruSurround XT technology is incorporated under license from SRS Labs, Inc.

The SRS TruSurround XT Function is activated only when the audio input signal is Stereo.

42

SOUND

How to Set the Output of Subwoofer

You can set this function when you wish to install your subwoofer system.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

 

 

 

3

Press Up and Down buttons to move to “SUB WOOFER .

 

4

Press Left and Right buttons to select “SUB WOOFER .

SUB WOOFER menu items appear.

 

5

Choose one of the items listed. Press Left and

 

Right buttons to adjust.

 

 

Press MENU button after the setting is done, and Menu goes to the previous menu. If the EXIT button is pressed, the menu disappears.

-The frequencies in the entry are the subwoofer’s frequency range.

-You make sure to use a subwoofer speaker system with built-in amplifier.

43

HYUNDAI Digital PDP TV

How to Set the Speaker Out

If you wish to use an external audio system, you can turn off the TV speakers.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

 

 

 

3

Press Up and Down buttons to move to

SPEAKER OUT .

 

4

Press Left and Right buttons to select

ON/OFF .

 

 

 

Press MENU button after the setting is done, and Menu goes to the previous menu. If the EXIT button is pressed, the menu disappears.

SOUND

44

SOUND

How to Set the Digital Audio Output

The digital audio output terminal allows you to enjoy digital sound. (For more details, see page 28)

 

Press Menu button.

 

 

 

Menu items appear on the screen.

 

1

Press Up and Down buttons to move to

.

2

Press

button to select

.

 

 

 

 

 

3

Press Up and Down buttons to move to

 

 

 

 

“DIGITAL AUDIO”

 

 

4

Press Left and Right buttons to select ON/OFF.

Whenever you press Left or Right button, the mode shifts in following order.

 

Dolby

PCM OFF

 

 

Press MENU button after the setting is done, and Menu goes to the previous menu. If the EXIT button is pressed, the menu disappears.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

45

HYUNDAI Digital PDP TV

How to Set Audio Language

While watching a digital program, you can listen to foreign language if the program is supported with foreign language.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

 

 

 

3

Press Up and Down buttons to move to

AUDIO LANGUAGE .

 

4

Whenever you press Left or Right button,

the mode shifts in following order.

 

 

ENGLISH SPANISH

FRANCE

 

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

SOUND

How to Directly Select Audio Language : Press the button.

-Whenever you press this button, the mode shifts MONO STEREO SAP in order when receiving analog signals.

You can select one of the languages listed you prefer when receiving digital signals.

- If you want to see language information while watching a digital channel, press the

button to display

language information that is currently received.

 

46

CHANNEL

How to Store Channels Automatically

-Your TV can memorize and store all of the available analog/digital broadcast signals for both “off-air” (antenna) and cable channels.

-Before your television can begin memorizing the available channels, make sure to specify the type of the signal source (antenna or cable) connected to your TV.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

 

2

Press

button to select

.

 

AUTO SCAN is highlighted.

 

 

 

 

 

3

Press

button to select “AUTO SCAN”.

 

 

 

 

AUTO SCAN menu items appear.

 

 

4

Press Left and Right buttons to select the type

of antenna connection.

 

 

- In case of ATV/DTV (ANT1) :

When watching both analog broadcast and digital broadcast at the same time with ANT1

Press Up and Down buttons to move to AIR TV or CATV.

• AIR ONLY : Watching the analog over-the-air and

digital over-the-air signals via ANT1 input port.

• CABLE ONLY : Watching the Cable and digital cable

signals via ANT1 input port.

5

- In case of ATV (ANT1) + DTV (ANT2) :

When watching analog broadcast with ANT1 and digital broadcast with ANT2. Press Up and Down buttons to move AIR + AIR, AIR + CABLE or CABLE + AIR.

• AIR(ANT1)+AIR(ANT2) : Watching the analog over-the-air via ANT1 input port and the digital over-the-air signal via ANT2 input port.

• AIR(ANT1)+CABLE(ANT2) : Watching the analog over-the-air via ANT1 input port and the digital cable via ANT2 input port.

• CABLE(ANT1)+AIR(ANT2) : Watching the analog cable via ANT1 input port and the digital over-the-air via ANT2 input port.

6

Press Left and Right buttons to set up CABLE BAND.

*CABLE BAND NOTE : STD (Standard), HRC (HRC band), IRC (IRC band)

(For further band information, contact your cable service provider.)

47

HYUNDAI Digital PDP TV

7

Press button.

AUTO SCAN is activated.

CHANNEL

48

CHANNEL

How to Set Favorite Channels

Users can store frequently watched channels to quickly access a preferred channel.

- How to store the channel you are currently watching as a favorite channel

Press “BOOK-MARK” button.

Then the channel will be stored while Favorite Channel

Selected is displayed on the screen.

- How to access the stored favorite channel

Press FAVORITE button.

You can access the favorite channel by pressing this button repeatedly.

- How to deselect a favorite channel

Display the channel to be deleted on the screen and then press the BOOK-MARK button twice.

The stored channel is deleted while Favorite Channel Deselected is displayed on the screen.

The Favorite function is available only with remote control.

49

HYUNDAI Digital PDP TV

How to Fine Tune Channel Reception

If the reception is clear, you do not have to fine tune channels, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press

button to select

.

 

 

 

 

 

3

Press Up and Down buttons to move to “FINE TUNE”.

 

4

Press

button to select “FINE TUNE”.

 

FINE TUNE menu items appear.

 

 

5

Press Left and Right buttons to adjust the screen.

The displayed channel digit is the channel

 

 

that is currently viewed.

 

 

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

The selected OSD for fine tuned channels is highlighted in orange.

CHANNEL

50

CHANNEL

How to the LNA (Low-Noise-Amplifier) Feature

If the reception is clear, you don’t have to use this feature.

If the signal is weak or distorted, perform the following steps.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

 

 

 

3

Press Up and Down buttons to move to “LNA”.

 

4

Press Left and Right buttons to set to

ON/OFF .

Press MENU button after the setting is done, and Menu goes to the previous menu. If the EXIT button is pressed, the menu disappears.

51

HYUNDAI Digital PDP TV

How to Choose Your Language

Users can select their language preference in order to display main menus and sub menus, etc.

 

Press Menu button.

 

 

 

Menu items appear on the screen.

 

 

 

 

OFF

 

 

 

OFF

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

LANGUAGE is highlighted.

 

 

 

 

 

3

Whenever you press Left or Right button,

 

the mode shifts in following order.

 

 

ENGLISH FRANÇAIS

ESPAÑOL

 

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

SETUP

52

SETUP

How to Set Clock, On/Off Time, Sleep Time

-You can automatically turn on or off the TV at a preset time. To do this, you must set the clock if you wish to use the automatic on or off timers.

-No Signal Timeout allows you to automatically turn off the TV if there is no broadcast signal for a certain period of time.

 

Press Menu button.

 

 

 

Menu items appear on the screen.

 

1

Press Up and Down buttons to move to

.

2

Press

button to select

.

 

 

 

3

Press Up and Down buttons to move to “TIME”.

 

4

Press

button to select “TIME”.

 

The CLOCK items appear.

 

 

- To set the Current Time :

Press Left and Right buttons to move between Hour, 5 Minute and AM/PM and Press Up and Down buttons to

set Hour, Minute and AM/PM.

After the setting is done, you can set WAKE UP and OFF TIMER.

6

- To set the WAKE UP :

Press Left button to exit the item and

 

press down arrow button to move to WAKE UP.

7

Press

button to select and press Left/Right and

Up/Down buttons to move between items or set each item.

8

- To set the OFF TIME :

Press Menu button to exit and

 

press the down arrow button to move to OFF TIME.

9

Pres Left and Right buttons to move to the items and

Press Up and Down buttons to set each item (See step 5)

Continued on next page.....

53

HYUNDAI Digital PDP TV

Continued from previous page..... (Set the SLEEP TIMER and NO SIGNAL TIMEOUT)

10

11

12

13

- To set SLEEP TIMER :

Press Left button to exit and press the down arrow button to move to “SLEEP TIME”.

Whenever the Left or Right button, the mode shifts in following order.

30 60 90 120 240 OFF

- To set NO SIGNAL TIMEOUT :

Press Up and Down button to move to “AUTO OFF”.

Press Left and Right button to select ON/OFF .

Press MENU button after the setting is done, and Menu goes to the previous menu. If the EXIT button is pressed, the menu disappears.

SETUP

54

SETUP

How to Set the Geometry in PC Mode

This function is only available in PC mode.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press

button to select

.

 

 

 

 

 

3

Press Up and Down buttons to move to “IMAGE ADJUST”.

 

4

Press

button to select “IMAGE ADJUST”.

 

Then the IMAGE ADJUST items appear.

 

5

Press Up and Down buttons to move to items you want.

Press Left and Right buttons to adjust.

 

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

H. POSITION : To adjust the horizontal position of the picture.

V. POSITION : To adjust the vertical position of the picture.

FREQUENCY : To eliminate the picture noise.

PHASE : To eliminate the shake of picture.

If the display input signal (resolution) has been changed, the picture will be automatically optimized.

55

HYUNDAI Digital PDP TV

How to Set Key Lock

This function is used to prevent from using the control buttons on the front of the TV or from connecting external devices to the TV. You make sure to set a PIN number to use this function.

Press Menu button.

Menu items appear on the screen.

1

Press Up and Down buttons to move to

.

2

Press

button to select

.

 

 

 

 

 

3

Press Up and Down buttons to move to “LOCK”.

 

4

Press

button to select “LOCK”.

 

Then the Enter PIN number window appears.

 

The default is 4 digits (0-0-0-0).

 

5

Press the numeric keys to enter your PIN number.

The LOCK items appear.

 

 

6

Press

button to select “CHANGE PIN”.

Then the Enter PIN number window appears.

7

Enter a 4-digit PIN number.

 

 

When the Confirm PIN number window appears,

 

enter the PIN number again.

 

 

8

- To set Key Lock :

 

 

 

 

 

 

Press Up and Down buttons to move to “KEY LOCK”.

9

Press Left and Right buttons to set to

ON/OFF .

When setting to ON, the control buttons on the

 

front of the TV will be engaged.

 

 

 

Continued on next page ......

 

 

SETUP

56

Continued from previous page..... (Set the Lock External Signal function.)

10

11

12

- To set Aux Block :

Press Up and Down buttons to move to “AUX BLOCK”.

Press button to select “AUX BLOCK”.

Then the AUX BLOCK items appear.

Press Up and Down buttons to move to the item you want. Press Left and Right buttons to set to ON/OFF .

If the item is set to ON, such item is disabled.

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

SETUP

-The Lock External SIGNAL function is designed to prevent a VCR or game player from being connected to the TV.

-If you forgot your PIN number, press the MENU + SAP + SLEEP + INFO buttons on the remote control in sequence to restore the default number, 0-0-0-0.

-The Key Lock function will be disengaged when you turn off and then on AC power or when a power failure happens.

57

HYUNDAI Digital PDP TV

How To Set Block Program

This(V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station.

The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked.

V-Chip rating and categories

Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to- video movies use the Movie Rating System (MPAA) only.

Ratings for Movies previously shown in theaters :

Movie Ratings :

- Blocking Off

(Permits all programs)

 

- G

(General audience)

 

- PG

(Parental guidance suggested)

 

- PG-13

(Parents strongly cautioned)

 

- R

(Restricted)

 

- NC-17

(No one 17 and under admitted)

 

- X

(Adult only)

If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

- TV-G

(General audience)

- TV-PG

(Parental guidance suggested)

- TV-14

(Parents strongly cautioned)

- TV-MA

(Mature audience only)

- TV-Y

(All children)

- TV-Y7

(Children 7 years older)

TV Rating Children : - Age

(applies to TV-Y, TV-Y7)

- Fantasy Violence

(applies to TV-Y7)

TV Rating General : - Age

(applies to TV-G, TV-PG, TV-14, TV-MA)

-

Dialogue-sexual dialogue

(applies to TV-PG, TV-14)

-

U Language-adult language (applies to TV-PG, TV-14, TV-MA)

-

Sex-sexual situations

(applies to TV-PG, TV-14, TV-MA)

-

Violence

(applies to TV-PG, TV-14, TV-MA)

SETUP

58

...... Continued from previous page.

SETUP

1

2

3

4

5

6

7

8

9

Press Menu button.

Menu items appear on the screen.

Press Up and Down buttons to move to

icon

and press buttons to select.

 

The message “Enter PIN” will appear.

Enter your 4-digit PIN number.

The new screen will appear.

Press Up and Down buttons to move to

“BLOCK PROGRAM” and press buttons to select.

The new screen will appear.

Press Left and Right buttons to “ON”.

Press Up and Down buttons to move to “TV-Guide” or “MAPP”.

Press button to select “TV-Guide” or “MAPP”

The new screen will appear.

Press Up and Down or Left and Right buttons to choose items.

Press Up and Down buttons to select “U” or “B”

(U=Unblock, B=Block)

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

TV-guide menu screen

MAPP menu screen

59

HYUNDAI Digital PDP TV

How to View Closed Captions

Choices in the closed caption menu are : CC Mode, Priority (Analog caption or Digital caption), and Option.

1. CC MODE :

ON : Captioning information is always shown, when available.

OFF : No captioning information is displayed.

On mute : Captioning information is only when the TV's sound is mute, when available.

(To mute the sound, press the mute button on the remote control and captioning information will appear on the screen, if available)

If you turned off the speakers in the Audio menu, closed captioning won’t appear when you press the mute button on the remote.

• CAPTION :

The form for the words that scroll across the bottom of the TV screen : usually the audio portion of the program provided for the hearing impaired.

CC 1 : For video related information that can be displayed. Script can be in any language.

CC 2/3/4 : Other modes used for video related information.

• TEXT :

The term for the words that appear in a large black frame and almost cover the entire screen : Usually message provided by the broad caster.

T 1 : Blanks out a large portion of the picture on the television screen, and display program guide or any other information currently being transmitted.

T 2/3/4 : other modes that display information and blank out a large portion of the picture of the TV screen.

SETUP

60

SETUP

...... Continued from previous page.

3. OPTION :

Customized closed captioning for the digital caption by choosing the settings for the following options :

SIZE : Set the size of the words - AUTOMATIC -> STANDARD -> LARGE -> SMALL.

TEXT COLOR : Chose a color for the text - AUTOMATIC -> WHITE -> BLACK -> RED -> GREEN -> YELLOW -> MAGENTA -> AND CYAN.

TEXT OPACITY : Specify the opacity for the text color - AUTOMATIC -> SOLED -> TRANSPARENT -> TRANSLUCENT.

BG(BACKGROUND) COLOR : Select a background color - AUTOMATIC -> WHITE -> BLACK -> RED -> GREEN -> YELLOW -> MAGENTA -> CYAN.

BG OPACITY : Specify the opacity for the background - AUTOMATIC -> SOLED -> TRANSPARENT -> TRANSLUCENT.

 

Press Menu button.

 

 

Menu items appear on the screen.

 

1

Press Up and Down buttons to move to

icon

and press buttons to select.

 

2

Press Up and Down buttons to move to

 

“CLOSED CAPTION” and press buttons to select.

 

Closed Caption menu appear.

 

3

CC MODE is highlighted.

 

Press Left and Right buttons to select “ON” or ON MUTE”.

 

Sub menu items are activated.

 

4

Press Up and Down buttons move between the items

Press Left and Right buttons to select the item.

5

When selecting the Option item, press

button.

Option menu appear.

 

6

Press Up and Down buttons move between the items

Press Left and Right buttons to select the item.

61

HYUNDAI Digital PDP TV

1

2

3

Press MENU button.

Menu items appear on the screen.

Press Up and Down buttons to move to

icon

and press buttons to select.

 

Press / buttons to move to “PIXEL SHIFT or FULL WHITE”.

Press

/

buttons to set to ON/OFF .

Press EXIT button to TV viewing or press MENU button to return to the previous menu.

SETUP

It may take from several minutes up to several hours to remove the image sticking. If a fixed pattern is display for a long time, you can prevent the latent image by switching FULL WHITE to on for 2 or 3 minutes on a hourly basis. The image sticking effect is influenced by the brightness of a fixed pattern and its display time. It is recommended that you reduce the level of the brightness by using picture controls (See page 30) when a fixed pattern is displayed for a long time.

62

DTV GUIDE

How to Use the Current Channel Guide

Users can get information on broadcasting time and signal status of the current digital channels.

 

Press Menu button.

 

 

Menu items appear on the screen.

 

1

Press Up and Down buttons to move to

 

and press button to select.

 

2

Press button again to select

 

the “CURRENT CHANNEL Guide”.

 

The information on broadcasting time and signal status, etc.

 

of the channels your are currently watching will be displayed.

How to Directly Use the Current Channels : Press the

button.

How to Reserve TV Programs Using the Total Channel Guide

-Users can get the broadcasting time information of all the entire digital channels. To do this, it is required to set the current time first.

-The displayed broadcasting time may be different from that provided by your local broadcasting company.

 

Press Menu button.

 

Menu items appear on the screen.

1

Press Up and Down buttons to move to

and press button to select.

2

Press Up and Down buttons to move to

“TOTAL CHANNEL GUIDE”.

3

Press button to select “TOTAL CHANNEL GUIDE”.

The broadcasting time and related information

 

of all channels will be displayed.

 

To schedule TV programs,

 

go to step 4 on the next page.

63

HYUNDAI Digital PDP TV

How to Use TV Program Reservation

If you have scheduled a TV program you are going to watch, the channel you are currently watching is automatically switched to the scheduled channel, or when your TV is in stand-by, the scheduled TV program is on at the defined time. If the AC power is off, this function is deactivated.

Continued from previous page.

4

Press Up/Down and Left/Right buttons to move to a

TV program to be scheduled.

 

5

Press

button.

A window “Will you schedule this program?” appears.

6

Press Left and Right buttons to move to YES ,

if you want to schedule. If you don’t want to schedule,

 

 

move to

NO .

7

Press

button to set.

If scheduled, the program title is highlighted in red

 

and if scheduling is cancelled, the red disappears.

You can check a listing of scheduled programs from the

SCHEDULE LIST menu. For more details, see the next page.

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

-You can schedule up to five TV programs at a time.

-When a scheduled TV program starts to broadcast, the program is automatically removed from the listing.

-You can schedule only TV programs on the air within 24 hours. This schedule keep updated. For example, if the current time is AM 10:00, any programs you want to schedule is allowed until AM 10:00 next morning.

GUIDE DTV

64

DTV GUIDE

How to Check or Cancel a Scheduled TV Program

Users can look through scheduled TV programs or remove a scheduled program from a listing of scheduled programs.

 

Press Menu button.

 

 

 

Menu items appear on the screen.

 

1

Press Up and Down buttons to move to

.

2

Press button to select

.

 

Press Up and Down buttons to move to “RESERVATION LIST”.

Press button to select “RESERVATION LIST”.

The Reservation List will appear.

- To remove a scheduled program :

Press Up and Down buttons to the program you want to remove.

Press button.

A window, CANCEL appears.

Left and Right buttons to select YES .

Press button to remove the item.

Press MENU button after the setting is done, and Menu goes to the previous menu.

If the EXIT button is pressed, the menu disappears.

65

HYUNDAI Digital PDP TV

How to Use an External Device Using the Remote Control

When setting other manufacturer s product using the remote control, some of the buttons on the remote control may not operate or different functions may be activated, or some of other manufacturer s products may not work. Some of DVD/VCR combos are allowed only either in DVD mode or VCR mode.

1. Turn on the external device you want to set.

2. Whenever you press button on the remote control, the mode shifts TV

VCR DVD CATV

in order.

 

 

3. If the external device has been chosen, press the

button and

button

at the same time for two seconds.

 

 

4. Enter an appropriate 3-digit number of the manufacturer from the DVD Setting Number Table. (If the product brand you want to set has multiple setting numbers, attempt to enter the setting numbers repeatedly until the product is turned off.)

5. When the product has turned off, press the button again.

(The appropriate button associated with the product will flash 3 times to show the product operates properly.)

6. Check that the Power button works normally and then check that other function buttons work normally.

If the Power button works normally but other function buttons do not, repeat the above steps from the beginning.

Depending on product brands or setting numbers, the power button may work normally but other function buttons do not work.

VCR Setting Number Table

APPENDIX

66

DVD Setting Number Table

APPENDIX

67

HYUNDAI Digital PDP TV

AMP Setting Number Table

CATV Setting Number Table

APPENDIX

68

APPENDIX

Glossary 1

Component video

Component video is sent through three cables: two color shade (chrominance) signals

 

and one brightness (luminance) signal. Component video achieves greater color

 

accuracy than composite video or S-VIDEO by splitting chrominance into two separate

 

portions.

Composite video

Composite video is sent through a single cable. Composite video combines the color

 

shade (chrominance) and brightness (luminance) information into one video signal.

S-VIDEO

S-VIDEO requires a single cable, which carries the brightness (luminance) and color

 

(chrominance) signals of the picture separately. S-VIDEO provides better resolution

 

than composite video, which carries the signals together.

480i

Provides 480 lines of resolution. Displays images using interlaced scanning, which first

 

transmits all the odd lines on the TV screen and then the even lines.

480p

Provides 480 lines of resolution. Displays images using progressive scanning, which

 

transmits each line from top to bottom.

720p

Provides 720 lines of resolution. Displays images using progressive scanning, which

 

transmits each line from top to bottom.

1080i

Provides 1080 lines of resolution. Displays images using interlaced scanning, which

 

first transmits all the odd lines on the TV screen and then the even lines. 1080i is one

 

of the formats used by HDTV (High Definition TV).

Digital television (DTV)

A new technology for transmitting and receiving broadcast television signals. DTV

 

provides higher resolution and improved sound quality over analog television.

HDTV(High Definition TV)

HDTV is a new kind of digital TV, creating a high quality picture, high definition. The

 

HDTV provides a theater-like screen with an aspect ratio of 16:9. Supports 720p or

 

higher.

SDTV(Standard Definition TV)

SDTV is a new kind of standard definition digital TV, having a range of lower resolution

 

than the HDTV. Supports 480p.

Cable Broadcast Receiver

A device that receives cable broadcasting. Connecting it to your TV set allows you to

(Converter)

watch a various channels.

Satellite Broadcasting

Provides crisp picture and clear audio quality throughout the country via a satellite.

VHF/UHF

VHF (Very High Frequency) is the part of the frequency spectrum from 30 to 300

 

megahertz. UHF (Ultra High Frequency) is the part of the frequency spectrum from 300

 

to 3,000 megahertz.

69

HYUNDAI Digital PDP TV

Glossary 2

DVD DVD (Digital Versatile Disc) is an optical disc that can store a huge volume of multimedia such as video, game, and audio application, etc.

Coaxial Cable Coaxial cable is the kind of rounded copper cable, which is generally used for TV antenna.

LNA (Low-Noise-Amplifier) Satellite applied technology. It is capable of amplifying weak signals so that any area experiencing a signal interruption may enjoy a clearer picture quality.

Aspect ratio Refers to the ratio between the width and height of the screen. This TV has a 16:9 (widescreen) aspect ratio, as opposed to a 4:3 aspect ratio.

PIP (Simultaneous Screen) PIP allows you to view two images at the same time in a single screen.

SWAP PIP function provides a main picture (larger image) and sub-picture (smaller image). The SWAP is designed to swap the sub-picture for the main picture. For example, while you are watching a main picture on TV and watching a sub-picture on VCR, you can instantly switch the two pictures by using the SWAP function.

Picture Mode Picture Mode features the optimal picture quality. There are Standard-Dynamic-Movie- MildCustom features in order. “CUSTOM” allows you to adjust Contrast, Brightness, Sharpness, Color and Tint.

Sound Mode Sound Mode features the optimal sound quality. There are Standard-News-Music- SportsCustom features in order. “CUSTOM” allows you to adjust high frequency sound, middle frequency sound and low frequency sound.

Digital Broadcasting Video and Audio signals digitized and transmitted by broadcasting companies complying with the new digital television standard developed by the ATSC (Advanced Television System Committee). Digital Broadcasting technology provides multimedia services including a variety of additional services as well as high-definition quality picture.

Analog Broadcasting NTSC-based Video and Audio signals transmitted by broadcasting companies.

SRS TruSurround TX A well-recognized 3D sound technology developed by US SRS Labs, Inc.

This technology delivers the ultimate audio experience only with two speakers as if through multi-channel speakers.

Dolby Digital Formerly known as AC-3, Dolby Digital is a digital audio coding technique that reduces the amount of data needed to produce high quality sound.

APPENDIX

70

APPENDIX

Glossary 3

Subwoofer Designed to improve ultra low frequency with about 150Hz. There are active type that is built with a built-in amplifier and passive type that is required to connect an additional amplifier to it.

Mono Audio signals are produced through a single channel. It is difficult to experience a spectacular sound since audio signals are reproduced with a single speaker.

Stereo Audio signals are produced through two channels. A spectacular sound is reproduced with two separated speakers.

Widescreen Term given to picture displays with a wider aspect ratio than NTSC 4:3. Digital HDTV is 16:9 widescreen. Most motion pictures also have a widescreen aspect ratio, some even wider than 16:9.

Panorama screen Refers to a screen whose distortion due to the screen size has been calibrated.

External source Refers source signals that come from other external devices such as a VCR, camcorder and DVD player, etc. than a TV set.

MTS A bilingual service provided when an overseas film, foreign drama or overseas news, etc. is aired. You can select one of two choices: mother tongue and foreign language. Or you can listen to both languages at the same time.

DVI Digital Visual Interface is a specification for digital signals. This interface using TMDS transmission reduces the loss of signal, allowing to enjoy a clear and crisp image.

HDMI HDMI (High-Definition Multimedia Interface) is the first and only industry-supported, uncompressed, all-digital audio/video interface.

HDMI provides an interface between any audio/video source, such as a set-top box, DVD player, or A/V receiver and an audio and/or video monitor, such as a digital television (DTV), over a single cable.

Virtual channels There is a new numbering system for DTV channels. The system, called the “DTV virtual channels,”gives a number for each DTV program service, and almost always uses the analog NTSC channel number as the first number for that station. The use of virtual channels allows stations to use the same channel number “brand” for both NTSC and DTV. The printed listing services have not yet changed their format to show only the DTV virtual channel numbering system.So in the example, the station is using RF Channel 38 for DTV and is transmitting DTV programs with virtual channel numbers 15.n. The 15.n is short hand for 15.1, and 15.2 and 15.3, etc., as there can be more than one DTV program lineup from the station. So, 15.1 is the first DTV program lineup, 15.2 is the second, 15.3 is the third.Some DTV stations may have only one virtual channel, others perhaps as many as six.Transmitting HDTV on one of the channels usually means few other channels are on the air at that time as the HDTV takes most of the DTV channel capacity.

71

HYUNDAI Digital PDP TV

Troubleshooting

Installation Problems

 

Symptom

Possible solution

How can I install an

Refer to pages 17~18.

antenna?

 

TV screen is not clear after

Indoors antenna may experience poor reception due to surrounding buildings. Please

installing an indoors

install an outdoors antenna or wireless antenna.

antenna.

 

How can I view cable

Please install a cable broadcasting receiver (Converter).

broadcasting?

 

Picture Problems

 

Symptom

Possible solution

Neither picture nor

Check whether power is on.

sound comes up.

Check whether the power is cut or whether power cord is properly connected.

 

Try to plug another product’s power cord to the outlet the PDP is plugged into.

Picture turns on slowly

This symptom is not a malfunction. This delay is designed to prevent the distorted and

after power is on.

noisy picture when power is on. However, if the picture does not appear more than 5

 

minutes after power is on, call a service center.

Picture is distorted or frozen

This symptom may be caused by weak reception. Contact your local station or cable

while watching digital

company.

broadcasting.

 

Input Source information

Check whether your TV is properly connected to external devices.

only appears on black

 

screen.

 

Poor reception on some

Check whether you selected proper channels. Try re-orienting your antenna. Ensure

channels.

LNA is activated.

Black and white on some

Check other channels for black and white screen. Adjust colour.

channels.

 

TV won’t turn on.

Ensure the power cord is plugged.

Screen is too bright or too

Adjust brightness.

dark.

 

APPENDIX

72

APPENDIX

 

 

 

 

Auto On does not work.

Ensure to use the remote control or power button on the product to turn off your TV. If

 

 

 

you unplug the power cord, the stand-by consumption power becomes 0 (zero), which

 

 

 

causes the programmed time to be erased.

After setting the time,

Ensure to use the remote control or power button on the product to turn off your TV. If

I turned TV off and turn it on.

you unplug the power cord, the stand-by consumption power becomes 0 (zero), which

The programmed information

causes the programmed time to be erased.

 

 

has been erased.

 

Sound Problems

 

 

 

Symptom

Possible solution

Too much noise occurs.

Check whether the audio setting is in the Stereo mode. In the Stereo mode, the sound

 

 

 

may be distorted in the area where experiences poor reception or is located far away

 

 

 

from a TV broadcasting station.

No sound while viewing a

Make sure an audio or audio/video component is securely inserted into the appropriate

 

 

cable channel

jacks. Check other channels for sound. Check the volume settings on the cable

 

 

 

broadcasting receiver.

Picture is OK but sound does

Try to press volume up/volume down buttons of your remote control.

 

 

not come out.

 

One of the speakers does not

Select sound balance and make proper adjustment. (Page 39)

 

 

produce sound.

Check the speaker connection cables.

General

 

 

 

Symptom

Possible solution

Remote control won't work.

Check whether there is a blocking object between the remote control and PDP.

 

 

 

Make sure your PDP is Power On. (In case of normal, LED on the front panel is in Red.)

 

 

 

Check whether batteries are inserted with proper polarities(+, -).

 

 

 

When the batteries are worn out, replace with new ones.

Where does the S-Video

Connect the two Audio jacks from the S-Video cable to the left and right ports on the

cable plug in for audio

Composite.

 

 

output?

 

Strange noises are heard.

Ticking noise during or after watching is caused by the change of ambient

 

 

 

environment such as humidity and temperature, which is characterized by plastic

 

 

 

products. Strange ticking noise occurs because a signal is suddenly transmitted to the

 

 

 

PDP panel. So, this is not a malfunction.

I tried to use the TV screen

Adjust the resolution referring to the standard signal mode table. Check the

 

 

as a PC monitor

specification of your video card installed in your PC. If your video card does not work in

 

 

but it doesn’t work.

supported hardware. Try upgrading the video card’s driver.

73

HYUNDAI Digital PDP TV

Care and Cleaning

Cabinet Cleaning

Wipe a soft dry cloth.

Do not use inflammables like Benzene or Thinner, or wet clothes.

Do not scratch the panel of PDP with a fingernail or pointed object.

Screen Cleaning

Clean the screen with a soft cloth moistened in mild glass detergent and dry with a soft cloth.

Never use any solvent on the screen such as Acetone, Benzene, or

Thinner, etc.

Cleaning Inside

When the inside needs to be cleaned, contact a service center or distribution agent where the item is purchased.

It is recommended cleaning is complete before the rainy season.

APPENDIX

74

Product Specifications

Model

 

 

Q421S/Q421H

Q501

 

 

 

 

 

Input

 

S-Video

1EA (A/V audio common)

1EA (A/V audio common)

 

 

 

 

 

 

 

Video (RCA)

1EA (Audio included)

1EA (Audio included)

 

 

 

 

 

 

 

Component(Y/Cb/Cr)

2EA (Audio included)

2EA (Audio included)

 

 

 

 

 

 

 

Antenna

2EA (ANT1+ANT2)

2EA (ANT1+ANT2)

 

 

 

 

 

 

 

PC Connection jack

D-SUB

D-SUB

 

 

Max. resolution

1024 X 768 @ 85 Hz

1024 X 768 @ 85 Hz

 

 

Audio

L/R

L/R

 

 

 

 

 

 

 

HDMI-HDCP(or DVI-HDCP)

1EA

1EA

 

 

 

 

 

Output

 

Subwoofer

1EA

1EA

 

 

 

 

 

 

 

Video

1EA (Audio included)

1EA (Audio included)

 

 

 

 

 

TV/Video

 

Color system

NTSC M

NTSC M

 

 

 

 

 

 

 

Sound system

FM

FM

 

 

 

 

 

 

 

Video system

Component, S-Video, Composite, PC,

Component, S-Video, Composite, PC,

 

 

 

HDMI(or DVI)

HDMI(or DVI)

 

 

 

 

 

Power

 

Supply

AC 100 - 240 V, 50/60 Hz

AC 100 - 240 V, 50/60 Hz

 

 

 

 

 

 

 

Consumption power

Typical 280W / 380W

450W

 

 

 

 

 

 

 

Stand-by power

Typical 3.5W

Typical 3.5W

 

 

 

 

Dimension (W x D x H mm - Without Stand)

1030 x 79 x 631

1208 x 79 x 724

 

 

 

 

(W x D x H mm - With Stand)

1030 x 279 x 716

1208 x 279 x 810

 

 

 

 

 

Weigh (Without Stand)

 

 

28 Kg

43.0 Kg

 

 

 

 

 

(With Stand)

 

 

32 Kg

47.0 Kg

 

 

 

 

 

Control type

 

 

Remote control, Key control

Remote control, Key control

 

 

 

 

 

- The above specifications may be subject to change without prior notice.

APPENDIX

75

HYUNDAI Digital PDP TV