Hubbell Euclid PBP Pendant User Manual

Size:
375.4 Kb
Download

INSTRUCTIONS

2020

Publication No. 132

January 1985

Hubbell Industrial Controls, Inc.

Repl.: January 1984

EUCLID™ PBP PENDANT

PUSHBUTTON STATIONS

ASSEMBLY AND PARTS INFORMATION

Step #1 Position hanger bracket (Item 1) as required and tighten locking nut 1/3 turn past finger tight.

Step #2 Pilot light assembly (Item 2) if used--push out plug (P/N 28338) from rear. Insert light assembly. Insert pilot light legend plate. Install locking ring.

Step #3 *Install button assembly (not Pictorially shown).Align keying tabs and holes and press push button assembly into terminal boards. Tighten hold down screws. (Not used on MS2 & MS5).AVOID OVERTIGTENING

Step #4 *Install terminal board with button assembly working from top to bottom. Use8-32x 1/2" (P/N 47661098) "sems" screws (Item 4) where single thickness terminal board is fastened. Observe "Top" marking on each board.AVOID OVERTIGHTENING

Step #5 *Use8-32x 5/8" (P/N47661-100)"sems" screws (Item 5) where two terminal boards overlap.AVOID OVERTIGHTENING

Step #6 Use8-32x 1/2" (P/N47243-059)pan head screws (Item 6) to install button guards and back cover.CAUTION: DO NOT OVERTIGHTEN THESE SCREWS. Recommended torque is 10 in. lbs. To 12 in. lbs. Maximum. A slight rubber bulging is allowed.

* Where direct wired push buttons are used, Steps #3, #4, & #5 do not apply.

PILOT LIGHTS

DESCRIPTION

CATALOG

LAMP

DESCRIPTION

CATALOG

LAMP

NUMBER

PART NO.

NUMBER

PART NO.

 

 

Pilot Light 120v 60 Hz AC

PL1

57465-015

Pilot Light 120V DC

PL3

57465-043

Pilot Light 240v 60 Hz AC

PL2

57465-015

Pilot Light 240v DC

PL4

57465-007

 

 

 

 

 

 

 

 

 

 

 

CONTACT

 

 

 

ENCLOSURE DIMENSIONS

INTERRUPTING

 

 

 

 

 

RATINGS

 

 

MOTION

A

APPROX. WT.

CATALOG NO.

MULTI-SPEED

 

 

ASSEMBLED

SINGLE BREAK

 

 

 

 

 

1*

7-7/8"

2-1/2 lbs.

E2

A.C.

120v

 

6A

 

2 Buttons

 

 

 

35% PF

240v

 

3A

 

2

13-11/16"

4-1/2 lbs.

E4

D.C.

125v

 

.4A

 

4 Buttons

 

 

 

IND

250v

 

.2A

 

3

18"

5-1/2 lbs.

E6

SINGLE SPEED

 

6 Buttons

 

 

 

DOUBLE BREAK

 

4

22-5/16"

7 lbs.

E8

A.C.

120v

 

6A

 

8 Buttons

 

 

 

35% PF

240v

 

3A

 

* Pilot light is not available on 1 motion enclosure

D.C.

125v

 

1.1A

 

IND.

250v

 

.55A

 

 

 

 

 

 

SINGLE SPEED INSERT

 

DESCRIPTION

CAT.

TYPICAL

 

 

DIRECT

APPLI-

 

SYMBOL

PLUG-IN*

WIRED**

NO.

CATIONS

 

MOMENTARY

--

PG1

Crane control:

 

N.O.

trolley,

bridge

 

 

 

 

 

MOMENTARY

 

& hoist, etc.

 

--

DW1

 

 

 

 

N.O.

 

 

 

 

 

 

 

 

 

 

--

MAINTAINED

DWS

Start-Stop

 

 

functions

 

 

 

 

 

 

 

 

 

 

 

 

MOMENTARY

--

PG2

Interlocking,

 

crane control

 

N.O. & N.C.

 

 

 

 

 

 

 

MAINTAINED

--

PG3

Auxiliary

 

 

functions

 

 

N.O. & N.C.

 

 

 

 

 

 

 

 

MAINTAINED

 

 

Magnet

 

 

 

 

 

 

 

 

MOMENTARY

--

PG4 †

control

 

 

 

LIFT/DROP

 

 

 

 

 

 

 

 

 

Used

as

a

 

MOMENTARY

--

PG5 †

toggle

switch

 

MAINTAINED

and for

start-

 

 

 

 

 

 

 

stop functions

 

MOMEMTARY

 

 

Start-stop

on-

 

 

 

off functions

 

START-STOP

--

PG6 •

 

 

 

 

 

RESET-STOP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stop-startoff-

 

MOMENTARY

 

 

on functions

 

 

 

 

 

 

 

STOP-START

--

PG7 •

 

 

 

 

STOP-RESET

 

 

 

 

 

 

 

 

 

 

 

 

† PG4 and PG5 inserts have one button maintained and one button momentary.

* Terminal Base Cat. TB2 required for each plug-ininsert PG1, PG2, PG3, PG4, PG5, PG6, PG7 and MS2. Terminal Base TB5 required for MS5 insert.

**Terminal Base not required with direct wired unit.

• "Power On-Off"buttons recommended to comply with provisions of NEMA ICS3-442.15

MULTI-SPEEDINSERT

 

DESCRIPTION

 

TYPICAL

 

 

CAT.

APPLI-

SYMBOL

PLUG-IN*

NO.

CATION

USED TO A

 

For

MAXIMUM

 

multi-

OF THREE

MS2

speed

SPEED

 

func-

POINTS

 

tions

 

 

 

USED TO A

 

For

MAXIMUM

 

multi-

OF FIVE

MS5

speed

SPEED

 

func-

POINTS

 

tions

Hubbell Industrial Controls, Inc.

A subsidiary of Hubbell Incorporated

4301 Cheyenne Dr., Archdale, NC. 27262

Telephone (336) 434-2800• FAX (336)434-2803

http://www.hubbell-icd.com

Sales@hubbell-icd.com