Hotpoint WDUD9640G, WDUD9640K, WDUD9640P Instruction manual

0 (0)

Instructions for use

WASHER-DRYER

GB

English,1

!

This symbol reminds you to read this instruction manual.

GB

 

 

 

 

 

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

WDUD 9640

Description of the washer-dryer, 6-7

Control panel Display

How to run a wash cycle or a drying cycle, 8

Wash cycles and functions, 9

Table of wash cycles Wash functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Precautions and tips, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13-14

Assistance, 15-16

1

Hotpoint WDUD9640G, WDUD9640K, WDUD9640P Instruction manual

Installation

! Keep this instruction manual in a safe place for future GB reference. Should the appliance be sold, transferred or

moved, make sure the instruction manual accompanies the washer-dryer to inform the new owner as to its operation and features.

! Read these instructions carefully: they contain vital information on installation, use and safety.

Unpacking and levelling

Unpacking

!This is a separate part of the polystyrene base and should be removed with the base.

!IMPORTANT check when unpacking your machine.

1.Unpack the washer-dryer.

2.Check whether the washer-dryer has been damaged during transport. If this is the case, do not install it and contact your retailer.

3.Remove the 4 protective

screws and the rubber bush with the respective spacer, situated on the rear of the appliance (see also the installation leaflet).

2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2°.

Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washer-dryer.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply pipe by screwing it to a cold

water tap using a

3/4 gas threaded connec-

tion (see figure).

Before performing the connection, allow the water to run freely until it is perfectly clear.

2. Connect the other end of the water inlet hose to the washer-dryer,

screwing it onto the appliance’s cold water inlet, situated on the top righthand side on the rear of the appliance (see figure).

4.Seal the gaps using the plastic plugs provided.

5.Keep all the parts: you will need them again if the

washer-dryer needs to be moved to another location. ! Packaging materials are not children’s toys.

Levelling

Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly. 1. Install the washer-dryer

on a flat sturdy floor, without resting it up against walls, furniture cabinets or other.

3. Make sure there are no kinks or bends in the hose.

!The water pressure at the tap must be within the values indicated in the Technical details table (on the page 5).

!If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman.

!Ensure that the supply taps are allowing water through. Old taps may seize in the closed position and thus prevent water reaching the machine.

!Never use second-hand or old inlet hoses; use the products supplied with the machine.

2

Connecting the drain hose

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;

Where it connects to the waste water pipe cut end off spigot or remove the blanking cap

The drain hose may be connected to an undersink trap. Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot.

If it is placed over the edge of a basin or sink be sure the free end of the hose should not be underwater.

! We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length. Ensure that if the drain hose is pushed into a standpipe, that the end does not go down more than 15cms (6 inches). If the hose is pushed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make sure that:

the socket is earthed and in compliance with the applicable law;

the socket is able to sustain the appliance’s maximum power load indicated on the Technical Data Plate fixed on the machine;

the supply voltage is included within the values indica-

 

GB

 

ted on the Technical Data Plate fixed on the machine.

 

 

the socket is compatible with the washer-dryer’s plug. If

 

 

 

this is not the case, replace the socket or the plug.

 

Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and you should wish to re-route the mains cable through partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug: Important: the wires in the mains lead are coloured in accordance with the following code:

Green & Yellow

Earth

Blue

Neutral

Brown

Live

3

 

 

As the colours of the wires in the lead may not correspond

GB

 

with the coloured markings identifying the terminals in your

 

 

plug, proceed as follows:

 

 

 

 

 

Connect Green & Yellow wire to terminal marked E or

 

 

or coloured Green or Green & Yellow.

 

 

Connect Brown wire to terminal marked L or coloured

 

 

Red.

 

 

 

 

Connect Blue wire to terminal marked N or coloured Black.

 

 

If a 13 amp plug (BS 1363) is used it must be fitted with a

 

 

13 amp fuse, either in the plug or adaptor or at the distri-

 

 

bution board.

 

 

 

 

If you are in any doubt regarding the electrical supply to

 

 

your machine, consult a qualified electrician before use.

 

 

How to connect an alternative plug:

 

 

The wires in this mains lead are coloured in accordance

 

 

with the following code:

 

 

 

BLUE

 

NEUTRAL (N)

 

 

BROWN

 

LIVE (L)

 

 

GREEN & YELLOW

EARTH (E)

 

 

 

 

 

 

 

GREEN &

 

 

 

 

YELLOW

 

 

 

 

BROWN

13 ampere fuse

 

 

 

 

 

 

 

BLUE

CROSS-BAR

 

 

 

 

CORD GRIP

 

 

 

 

 

 

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using the wash cycle (60°C).

Disposing of the appliance:

When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.

!The washer-dryer should not be installed in an outdoor environment, not even where the area is sheltered, because it may be very dangerous to leave it exposed to damp, rain and thunderstorms.

!When the washer-dryer is installed, the mains socket must be within easy reach.

!Do not use extensions or multiple sockets.

!The power supply cable must never be bent or dangerously compressed.

!The power supply cable must only be replaced by an authorised serviceman.

Warning! The company denies all liability if and when these norms are not respected.

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GB

Technical data

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model

WDUD 9640

 

 

 

 

width 59.5 cm

Dimensions

height 85 cm

 

depth 60,5 cm

 

 

 

Capacity

from 1 to 9 kg for the wash programme

from 1 to 6 kg for the drying programme

 

 

 

 

Electrical

please refer to the technical data plate

connections

fixed to the machine

 

 

 

 

maximum pressure 1 MPa (10 bar)

Water connections

minimum pressure 0.05 MPa (0.5 bar)

 

drum capacity 62 litres

 

 

 

Spin speed

up to 1400 rotations per minute

 

 

 

 

Wash: programme ; temperature 60°C

Energy rated

(2nd press of the button); using a load of 9 kg.

programmes

Drying: the smaller load must be dried by

according to

selecting the “EXTRA” dryness level. The

load must consist of 3 sheets, 2 pillowca-

regulation

ses and 1 hand towel;

EN 50229

the remainder of the load must be dried by

 

selecting the “EXTRA” dryness level.

This appliance conforms to the following

EC Directives:

-2004/108/EC (Electromagnetic Compatibility)

-2006/95/EC (Low Voltage)

-2002/96/EC

5

Loading...
+ 11 hidden pages