Instruction booklet
TUMBLE DRYER TCAM 80C |
TCYM 80C |
TCEM 80C |
TCFM 80C |
Important Information |
|
PRODUCT DATA... (EU Regulation 392/2012)
Rated capacity of Cotton laundry for the standard programme at full load 8 kg |
Energy efficiency class C |
|
|
The weighted Annual Energy Consumption (AEc) 627.2 kWh.
Consumption per year, based on 160 drying cycles of the standard cotton programme at full and partial load, and the consumption of the low-power modes. Actual energy consumption per cycle will depend on how the appliance is used
This household tumble dryer is a Non-Automatic Condenser Dryer
Energy consumption: full load Edry 5.26 kWh, partial load Edry1/2 2.91 kWh
Power consumption: off-mode (Po) 0.00 W
Duration of the ‘left-on mode’ for power management systems - N/A minutes
The ‘standard cotton programme’ suitable for drying normal wet cotton laundry that is the most efficient programme in terms of energy consumption for cotton used at full and partial load is High Heat
Programme time (minutes) weighted (Tt) full & partial load 115, full load (Tdry) 150, partial load (Tdry1/2) 88
Condensation efficiency class C
Average condensation efficiency (%): full load (Cdry) 73, partial load (Cdry1/2) 74, weighted (Ct) full & partial load 74
Airborne acoustical noise emissions 69 dB(A) re 1 pW.
This data is also available on the website http://www.hotpoint.eu/hotpoint
This symbol reminds you to read this booklet.
FLUFF FILTER
You must clean the fluff filter after EVERY drying cycle.
Step 1
Open the door of your dryer.
Step 4
Refit the filter with the curved side towards you.
Step 2
Pull out the filter (using the two finger grips).
Step 5
Make sure the filter is pushed fully home - NEVER run the dryer without the filter in position.
Step 3 |
! |
|
|
|
|
Open the filter and clean any fluff |
|
|
deposits from the filter mesh. |
|
|
|
|
|
Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.
It will take longer to dry and as a result will use more electricity during drying.
!You MUST empty the water container after EVERY drying cycle.
Failure to empty the water container will cause the machine to stop heating and the load may still be wet at the end of the drying cycle. The ‘Empty Water’ light will tell you that the water container is full and needs emptying.
WATER CONTAINER
You MUST empty the water container after EVERY drying cycle.
Removing the water container:
Step 1
Pull the water container towards you and remove it completely from the dryer.
Step 2
Empty all the water in the water container.
Step 3
Replace the water container making sure that it is securely fixed.
Installation
WHERE TO PUT YOUR DRYER
If you are going to install the dryer under a work counter be sure to leave
a 10mm space between the top and any other objects on or above the machine and a 15mm space between the sides and any kitchen units or walls to ensure proper air circulation.
The dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door.
!Priming the Water Collection System.
When your dryer is new, the water container will not collect water until the system is primed. This will take 1 or 2 drying cycles. Once primed it will collect water during every drying cycle.
CONDENSER UNIT
You MUST clean the fluff from the condenser EVERY month. Failure to clean the condenser could cause premature failure of your dryer.
Remove the condenser unit regularly (at least monthly) and clean off any fluff deposits.
Step 1
Open the condenser cover.
Step 2
Remove the condenser by turning the 3 catches
and pulling the condenser towards you. It is normal for some residual water to be left in the condenser unit.
Step 3
Flush the condenser from the rear with water to remove any fluff deposits.
Step 4
Replace the condenser unit and make sure that all 3 catches are closed and that the position arrows on the front of the condenser are pointing upwards.
WATER DRAINAGE CONNECTION
If the dryer is installed next to a drain the water can be plumbed into this drain. This does away with the need to empty the water container. The height of the drain must be less than 1m from the bottom of the dryer. Remove the existing hose from the dryer and connect it to the drain (if required add an additional length of hose).
2 |
1 |
Less than 1m |
ELECTRICAL CONNECTIONS
The socket must be grounded. The power supply cord should be checked periodically and, if required, replaced by a cord specially prepared for this dryer.
BEFORE YOU START USING YOUR DRYER
Once you have installed your dryer and before you use it clean the inside of the drum to remove any dust that could have accumulated during transport.
Dryer Description
Control panel |
|
|
Empty water |
|
|
|
|
TIMER |
|
|
Light |
Knob |
Indicator |
||
|
0 |
|
|
|
|
|
20 |
|
|
|
30 |
|
|
|
40 |
130 |
|
|
50 |
120 |
|
|
60 |
101 |
100 |
80 |
70 |
|
|
||
HEAT |
|
|
START |
Button |
|
|
Button |
The HEAT button selects drying temperature.
OUT: LOW heat IN: HIGH heat
The TIMER knob sets the drying time: rotate it clockwise, NEVER COUNTER-CLOCKWISE, until the indictor is pointing to the drying time you want to select.
The Empty Water indicator light signals that the water container is full and must be emptied. The light will take a few seconds to go out after replacing the empty water container, the dryer must be running for this to happen.
Note: If the water container fills up the indicator lights, the heat is turned off and your laundry will not dry.
Loading...