Hotpoint RLM51, RLA53, RLM53, RLA61, RLM61 User Manual

...
0 (0)

LARDER FRIDGE - MODELS RLA51, RLA53, RLA61, RLM51, RLM53, RLM61

INSTRUCTIONS FOR INSTALLATION & USE

GETTING STARTED: To ensure that your fridge runs reliably and efficiently follow these steps.

STEP 1

Choose a location for your fridge, away from any heat sources and allow adequate ventilation - 30mm

(11/4 inch) gap above.

STEP 2

Move the fridge into position, using the sides of the cabinet. Take care to avoid damaging the refrigerant circuit pipe work on the rear.

INSTALLATION

& SAFETY

 

 

 

 

CONTROLS

 

 

 

STEP 3

STEP 4

adjusting This vibration

NB. The only and

STEP 5

Plug in and switch on Allow the fridge to cool before placing food inside All food in the fridge

should be covered

Before plugging in and switching on, leave the fridge in its final location for at least 15 minutes to allow it to settle.

Your fridge is now working.

If after 24 hours your fridge is not operating as you want, refer to the Troubleshooting section.

ADVICE USEFUL

 

 

 

 

 

MAINTENANCE

& CLEANING

 

 

 

 

TROUBLESHOOTING

 

 

 

GUARANTEE

& SERVICE

 

 

Read the rest of these instructions to get the best from your appliance and remember to fill in your guarantee registration.

Keep this Book in a safe place for quick reference.

 

 

For Your Safety

 

For your safety, read the following advice:

 

The fridge cooling system contains a small amount of gas which is environmentally

 

friendly but flammable. To avoid any risk :-

 

Install the fridge following the installation instructions and ensure

 

 

that ventilation openings are kept clear of obstruction.

 

Take care when installing or moving the fridge to avoid damaging

&SAFETY INSTALLATION

 

the pipes on the rear.

If you suspect a leak, do not switch on the fridge, but open the

 

 

 

windows and doors to ventilate the room.

 

Do not use any mechanical or electrical devices inside the fridge, for

 

 

instance for manual defrosting.

 

Only use this fridge for storing domestic foodstuffs.

 

 

When installing your fridge :-

 

Ensure that the mains cable is not trapped underneath or behind the fridge

 

 

when you install or move it.

 

Do not stack any other appliance on top of this fridge as they may

 

 

damage the fridge or become unstable.

 

When using your fridge :-

 

Do not sit or stand on top of your fridge.

 

Do not store poisonous, flammable or dangerous substances in your fridge.

 

Do not use aerosol sprays for defrosting or cleaning your fridge.

If you sell the fridge, pass on this booklet to the new owner.

2

Hotpoint RLM51, RLA53, RLM53, RLA61, RLM61 User Manual

Installation

Location & Air Circulation

Locate your fridge away from sources of heat e.g. cookers, radiators, direct sunlight as extreme temperature will affect its performance.

Allow a minimum 100mm (4 inches) between the top of the fridge and the ceiling or the underside of a wall cupboard.

Providing you follow the recommended ventilation requirements you will :-

Prolong the life of the fridge.

Minimise the risk of condensation on the outside of the fridge.

Minimise the running costs.

Minimise operating sounds caused by vibration.

Minimum space required to open door

100mm (4 inches)

The fridge needs a space of 600mm (24 inches) in front to allow the door to open. When positioning the fridge next to a unit, a gap of 30mm (11/4 inch) can be left at the hinge side of the door to allow the easy removal of furniture. If preferred the fridge can be positioned so that a gap is not left. This will restrict how far the door can be opened but the furniture can still be removed (see diagram below). The door hinge side can be changed to make it easier to open (see ‘Door Reversal’ in the CLEANING & MAINTENANCE section).

TOP VIEW

TOP VIEW

 

 

 

 

 

 

 

 

600mm

600mm

 

 

 

 

 

 

 

 

 

 

 

 

30mm or more

less than 30mm

INSTALLATION

& SAFETY

 

 

3

Installation

&SAFETY

INSTALLATION

 

 

Levelling:

Level the fridge when it is in its final location by adjusting the front feet, until firm contact is made with the floor. This will stop rocking or vibration and keep the door aligned which helps the fridge run reliably and efficiently.

Note: Before plugging in and switching on, leave the fridge standing in its final location for at least 15 minutes to allow it to settle.

Bottle Retainer:

To fit the bottle rack retainer:

Locate the retainer groove at one end of the bottle rack and then gradually press down along the top edge until the retainer is fully in the home position.

Joining:

Equal height Hotpoint fridges and freezers can be joined together to look like one unit by using a Filler Kit available from Hotpoint Genuine Parts & Accessories Mail Order Hotline (see KEY CONTACTS, back page).

4

Installation

Electrical Supply

WARNING: This appliance must be earthed.

The fridge must be positioned so that the plug is accessible after installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING: To avoid a shock hazard do not insert the discarded plug into a socket anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE :

Green/Yellow - Earth

Blue

- Neutral

 

 

 

Brown - Live

 

 

 

INSTALLATION

& SAFETY

 

 

If you change the plug, the colour of wires in the mains lead may not correspond with the colour of the markings identifying terminals in the plug. You should therefore wire it as shown above.

Changing the Mains Lead

This fridge is fitted with a special mains lead. If you need to replace the mains lead due to damage, one can be bought from Hotpoint Service (see KEY CONTACTS, back page). It is strongly advised that this work is carried out by a qualified electrician.

CE Marking certifies that this appliance conforms to the following EEC directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

5

Controls

Controlling the Temperature of the Fridge Compartment

The control wheel on the front of the worktop adjusts the internal fridge compartment temperature. The internal temperature should be 5˚C or colder although some sections, such as the salad bin, will be slightly warmer.

The setting of the control wheel will depend on the location of the fridge, the room temperature and how often the door is opened. The normal set point (marked by a 3 and N on the dial) is usually suitable. If you need to adjust the temperature turn the control wheel:

Clockwise (higher number) - Colder

Anti-clockwise (lower number) - Warmer

CONTROLS

You can check the temperature of the fridge compartment by using a Fridge Freezer Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order Hotline (see KEY CONTACTS back page).

WARNING: Do not use a mercury filled thermometer, as breakage would cause a health hazard.

Your fridge must NOT be placed in a room where the temperature goes below 6˚C or above 38˚C for prolonged periods, as the internal fridge temperature will not be maintained.

6

Loading...
+ 14 hidden pages