Hotpoint FF4DK-TVZ, FF4DX-TVZ User Manual [UK]

0 (0)

Operating Instructions

 

 

 

REFRIGERATOR/FREEZER COMBINATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Contents

 

 

 

 

GB

 

 

 

 

 

 

 

 

Installation, 2-3

 

 

GB

 

 

 

 

Positioning and connection

 

 

 

Description of the appliance, 4-5

English,1

 

 

 

Control panel

 

 

 

Overall view

 

 

 

Start-up and use, 6-7

 

 

 

Starting the appliance

 

 

 

Chiller system

 

 

 

Using the refrigerator to its full potential

 

 

 

Using the freezer to its full potential

FF4DK(TVZ)(UK)

FF4DX(TVZ)(UK)

Maintenance and care, 8

Switching the appliance off Cleaning the appliance

Avoiding mould and unpleasant odours Holiday function

Optimization Energy Saving function Replacing the light bulb

Precautions and tips, 9

General safety Disposal

Respecting and conserving the environment

Troubleshooting, 10

Guarantee, 11

After Sales Service, 12

Installation

! Before placing your new appliance into operation

GB please read these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance.

! Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.

Positioning and connection

Positioning

1.Place the appliance in a well-ventilated humidity-free room.

2.Do not obstruct the rear fan grills. The compressor and condenser give off heat and require good ventilation to operate correctly and save energy.

3.Leave a space of at least 10 cm between the top part of the appliance and any furniture above it, and at least 12 cm between the sides and any furniture/side walls.

4.Ensure the appliance is away from any sources of heat (direct sunlight, electric stove, etc.).

5.In order to maintain the correct distance between the appliance and the wall behind it, fit the spacers supplied in the installation kit, following the instructions provided.

Levelling

1.Install the appliance on a level and rigid floor.

2.If the floor is not perfectly horizontal, adjust the refrigerator by tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it vertically and wait at least 3 hours before connecting it to the electricity mains. Before inserting the plug into the electrical socket ensure the following:

The appliance is earthed and the plug is compliant with the law.

The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the bottom left side of the fridge (e.g. 150 W).

The voltage must be in the range between the values indicated on the data plate located on the bottom left side (e.g. 220-240V).

The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it (see Assistance). Do not use extension cords or multiple sockets.

!Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

!The cable must not be bent or compressed.

!The cable must be checked regularly and replaced by authorised technicians only (see Assistance).

!The manufacturer declines any liability should these safety measures not be observed.

Connection of the water supply

To carry this out, use the kit provided which contains all the necessary elements for connection to the water supply.

To improve the performance of the Aqua Care, we recommend that you fit a tap with a filter on the pipe for the connection to the water system: in this way it will be possible to manually interrupt the water supply during long periods in which Aqua Care is not used.

!The water pressure inside the water system must be between 0.8 bar and 8 bar.

!The appliance must only be connected to a water supply suitable for drinking.

Your appliance is supplied with a 13amp fused plug that can be plugged into a 13amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING:

THIS APPLIANCE MUST BE EARTHED.

Replacing fuse covers:

When replacing a faulty fuse, a 13amp ASTA approved fuse to BS 1362 should always be used and the fuse cover re-fitted.

If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug.

Changing the plug:

Removing the plug

If your appliance has a non-rewireable moulded plug and you should wish to remove it to add a longer cable or to re-route the mains cable through partitions, units etc. please ensure that either:

-The plug is replaced by a fused 13amp rewireable plug bearing the BSI mark of approval.

or

-The mains cable is wired directly into a 13amp cable outlet, controlled by a switch (in compliance with BS 5733) which is accessible without moving the appliance.

2

Disposing of the plug

Cut off and dispose of the supplied plug if it does not fit GB your socket. The cable should be cut as close as

possible to the moulded plug. Remove the fuse.

WARNING:

To avoid a shock hazard do not insert the discarded plug into a socket anywhere else.

Fitting a new plug

IMPORTANT:

WIRES IN THE MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE...

Green and Yellow

- Earth

Blue

- Neutral

Brown

- Live

As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

-Connect Green and Yellow wire to terminal marked 'E' or or coloured Green and Yellow.

-Connect Brown wire to terminal marked 'L' or coloured red or brown.

-Connect Blue wire to terminal marked 'N' or coloured Black or Blue.

If a 13amp plug (BS 1363) is used it must be fitted with a 13amp fuse. A 15amp plug must be

protected by a 15amp fuse, either in the plug or adaptor or at the distribution board.

If you are in any doubt about the electrical supply to your machine, consult a qualified electrician before use.

CE Marking certifies that this appliance conforms to the following EEC directives :

Low Voltage Equipment - 73/23/EEC & 93/68 EEC Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

3

Hotpoint FF4DK-TVZ, FF4DX-TVZ User Manual

Description of the appliance

GB Control panel

 

 

 

 

 

 

 

 

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicator light

 

 

 

 

 

 

REFRIGERATOR

 

SUPER COOL

 

 

SUPER FREEZE

FREEZER

 

 

 

 

OPERATION

 

 

 

OPERATION

 

 

Indicator light

 

 

Indicator light

 

 

 

Knob

 

 

 

Knob

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SUPER COOL

Button

REFRIGERATOR OPERATION Knob

to regulate the temperature of the refrigerator compartment.

is the optimal temperature for energy saving levels.

is the holiday function (see Maintenance and care).

OFF switches the refrigerator off.

SUPER COOL (quick cool) to lower the temperature of the refrigerator compartment rapidly. When it is pressed, the SUPER COOL indicator light illuminates (see Start-up and use).

SUPER COOL Yellow indicator light (rapid cooling) illuminates when the SUPER COOL button is pressed.

POWER Indicator light illuminates when the appliance is connected to the electricity network.

SUPER FREEZE

Button

SUPER FREEZE button (rapid freezing) to freeze fresh food. When it is pressed, the SUPER FREEZE indicator light illuminates (see Start-up and use).

If pressed for at least 3 seconds, this activates the “Optimization Energy Saving” function (see Care and maintenance).

SUPER FREEZE Yellow indicator light (rapid freezing) illuminates when the SUPER FREEZE button is pressed.

FREEZER OPERATION Knob

to regulate the temperature of the freezer compartment.

is the optimal temperature for energy saving levels.

switches the appliance off, including the

refrigerator.

TVZ (see Using the freezer to its full potential)

! The indicator lights are also used to indicate an unusual temperature increase in the freezer compartment (see Troubleshooting).

4

Loading...
+ 8 hidden pages