Horton ICU, STC-35 User Manual

ARCHITECTURAL SPECS

Acoustic STC

-

35

ICU Swing

TM

®

,

1

DIVISION 08 - OPENINGS
SECTION 08 34 73– SOUND CONTROL DOOR ASSEMBLIES

Specifier Note: Coordinate and edit articles and paragraphs below to suit project requirements. Add section
numbers and titles per CSI "MasterFormat" and specifier's practice. Consult with manufacturer regarding
performance requirements for units applicable to project, as well as, related equipment and accessories required.

PART I – GENERAL

1.01 SUMMARY

A. WORK INCLUDED: Furnish complete intensive care aluminum door system, as specified, that has been

manufactured, fabricated and installed to maintain performance criteria stated by manufacturer without defects,
damage or failure.

B. RELATED WORK:

1. Masonry: Division 4, applicable sections.

2. Storefront; Glass; Hardware: Division 8, applicable sections.

3. Perimeter Sealants; Insulation: Division 7, applicable sections.

1.02 REFERENCES

A. AMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA) 101: Appendix Dissimilar

Materials.

B. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) Z97.1: Safety Glazing Materials Used in Buildings -

Methods of Test.

C. AMERICAN SOCIETY FOR TESTING AND MATERIALS:

1. ASTM E90-04: Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of
Building Partitions and Elements.

2. ASTM E413-04: Classification for Rating Sound Insulation

3. ASTM B221: Aluminum-Alloy Extruded Bars, Rods, Shapes and Tubes.

D. NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) 101: Code for Safety to Life from Fire in Buildings &

Structures.

E. THE ALUMINUM ASSOCIATION (AA) Aluminum Finishes Manual.

F. INTERTEK, WARNOCK HERSEY: Testing Laboratory and Certification Agency in partnership with ETL SEMKO

Testing and Certification includes, but is not limited to, Sound Transmission Door Assemblies as per
performance criteria of ASTM E90-04.

G. SOUND TRANSMISSION CLASS (STC) 35 in accordance with ASTM E-413-04.

1.03 SUBMITTALS

A. PRODUCT DATA: Submit manufacturer's complete product and installation data.

B. SHOP DRAWINGS: Submit drawings showing layout, profiles, product components including anchorage,

accessories, finish and glazing details (where required).

C. QUALITY ASSURANCE AND CLOSEOUT SUBMITTALS: Submit the following:

4242 Baldwin Boulevard
Corpus Christi, Texas
USA 78405-3399
Tel: [phone]
Fax: [phone]

www.hortondoors.com

The Automatic Choice

MANUAL ICU/CCU ENTRANCES

Sound Transmission Class Rated Manual
Swing Door System

A25.1

May 15Page 1 of 4

ARCHITECTURAL SPECS

Acoustic STC

-

35

ICU Swing

TM

®

,

2

1. Manufacturer's Operation and Maintenance Data.

2. Warranty document as specified herein.

1.04 QUALITY ASSURANCE

A. INSTALLERS QUALIFICATIONS: Installer experienced (as determined by contractor) to perform work of this

section who has specialized in the installation of work similar to that required for this project and who is
acceptable to product manufacturer.

B. MANUFACTURER’S QUALIFICATIONS: Manufacturer to have minimum (5) five years successful experience in

the fabrication of intensive care doors of the type required for this project. Manufacturer capable of providing
field service representation during installation, approving acceptable installer and approving application method.

1.05 WARRANTIES

A. MANUFACTURER'S WARRANTY: Units to be warranted against defect in material and workmanship for a

period of one year from the Date of Substantial Completion.
Manufacturer's warranty is in addition to, and not a limitation of, other rights owner may have under Contract
Documents.

B. DISTRIBUTOR'S WARRANTY: One year warranty: Labor and transportation charges for defective parts

replacement.

1.06 PROJECT CONDITIONS

FIELD MEASUREMENTS: Verify actual dimensions/openings by field measurements before fabrication and record
on shop drawings. Coordinate with fabrication and construction schedule to avoid construction delays.

1.07 DELIVERY, STORAGE AND HANDLING

A. ORDERING AND DELIVERY: Comply with factory's ordering instructions and lead time requirements. Delivery

shall be in factory's original, unopened, undamaged containers with identification labels intact.

B. STORAGE AND PROTECTION: Provide protection from exposure to harmful weather conditions and vandalism.

PART II – PRODUCTS

2.01 MANUFACTURER

HORTON AUTOMATICS, a division of Overhead Door Corporation, shall manufacture intensive care swinging
door(s) of type(s) and size(s) specified on plans and door schedule.

2.02 EQUIPMENT

A. MANUFACTURED DOOR UNITS: Shall be Acoustic STC-35 ICU Swing™ manual system and shall include

header, jambs and swing panel(s). All hollow extrusions to be filled with sponge rubber for sound absorption.
Available configurations shall include:

1. Unequal Pair: one wide swing panel (primary egress) and one narrow swing panel (auxiliary egress) normally
fixed.

2. Pair: two wide swing panels (both primary egress or primary/auxiliary combination)

3. Single: wide swing panel (primary egress)

B. HEADER: Shall be aluminum, 4" (102 mm) deep by 1 3/4" (44 mm) high.

4242 Baldwin Boulevard
Corpus Christi, Texas
USA 78405-3399
Tel: [phone]
Fax: [phone]

www.hortondoors.com

The Automatic Choice

MANUAL ICU/CCU ENTRANCES

Sound Transmission Class Rated Manual
Swing Door System

A25.2

May 15Page 2 of 4