70° 
DIGITAL CERAMIC HEATER
HZ-335, HZ-336 Series
IMPORTANT
SAFEGUARDS
READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS HEATER.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
IMPORTANT INSTRUCTIONS
1.Read all instructions before using this heater.
2.This heater is hot when in use. To avoid burns, do not let bare skin touch hot surface. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
3.Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4.Always unplug heater when not in use.
5.Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6.Do not use outdoors.
7.This heater is not intended for use in bathroom, laundry areas and similar moist indoor locations. Never locate heater where it may fall into a bathtub or other water container.
8.Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord
away from traffic areas where it will not be tripped |
|
over. |
1 |
9.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.
10.This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
11.It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.
12.To disconnect the heater, first turn controls to the OFF position, then grip the plug and pull it from the wall outlet. Never pull by the cord.
13.Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
14.To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
15.A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored.
16.Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
17.Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts.
18.The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
19.SAVE THESE
INSTRUCTIONS.
|
|
MODE: SET TIMER |
|
|
|
BASIC CONTROL PANEL OPERATION: |
Timer |
|
|
|
|
POWER |
|
|
High Power |
|
|
Continuous Run |
|
|
Low Power |
|
|
•Press Power once to start the heater on High Power, Continuous Run.
•Press Power again to change to Low Power, Continuous Run.
•Press Power a third time to turn the heater off.
MODE: SET TEMPERATURE
•Press Mode until the Timer icon blinks. The Hour display will appear.
•Use the Up or Down arrows to set an operation time between 1 and 10 hours.
•The heater will turn-off when time runs out.
FAHRENHEIT/CELSIUS
Set Temperature
F/C Temperature 
Display
•Press Mode until the Temperature icon blinks. The current room temperature will appear.
•Use the Up or Down arrows to set the desired temperature.
•The Temperature icon will stop blinking and the current room temperature will reappear after the desired temperature is set.
•The heater will turn-off shortly after the desired temperature is reached and the Power light above the display will blink.
•The heater will turn back on when the room temperature drops approximately 2 degrees below the desired temperature. The Power light will stop blinking and will remain lit.
•F/C feature functions from only the Power or Set Temperature screens.
•Press the F/C button to toggle between Fahrenheit and Celsius.
2
Loading...