Hitachi CP-X2011N, CP-X2511N, CP-X3011N, CP-X4011N Operating Guide

Projector

CP-X2011N/CP-X2511N

/CP-X3011N/CP-X4011N

User's Manual (detailed)

Operating Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read all manuals for this product. Be sure to read “Safety Guide” first. After reading them, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

NOTICE This entry notices of fear of causing trouble.

Please refer to the pages written following this symbol.

NOTE • The information in this manual is subject to change without notice.

•The manufacturer assumes no responsibility for any errors that may appear in this manual.

•The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

•Mac® is a registered trademark of Apple Inc.

•Windows® is a registered trademark of Microsoft Corporation in the U.S. and/or other countries.

•VESA and DDC are trademarks of the Video Electronics Standard Association.

•HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

•Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

All other trademarks are the properties of their respective owners.	1

Contents

Introduction . . . . . . . . . . . . . . . 3 SETUP menu . . . . . . . . . . . . . . 40

Features . . . . . . . . . . . . . . . . . . . . . . 3 Checking the contents of package. . . 3 Part names . . . . . . . . . . . . . . . . . . . . 4

AUTO KEYSTONE, KEYSTONE, AUTO ECO MODE,

ECO MODE, MIRROR, STANDBY MODE,

MONITOR OUT

Setting up . . . . . . . . . . . . . . . . . 7 AUDIO menu . . . . . . . . . . . . . . 42

Arrangement . . . . . . . . . . . . . . . . . . . 7

Connecting with your devices . . . . . . 9 Connecting to a power supply. . . . . 14 Using the security bar and slot . . . . 14

Remote control . . . . . . . . . . . . 15

Installing the batteries. . . . . . . . . . . 15 About the remote control signal . . . 15 Changing the frequency of remote control signal . . 16 Using as a simple PC mouse & keyboard . . 16

Power on/off . . . . . . . . . . . . . . 17

Turning on the power . . . . . . . . . . . 17 Turning off the power . . . . . . . . . . . 17

Operating . . . . . . . . . . . . . . . . 18

Adjusting the volume. . . . . . . . . . . . 18 Temporarily muting the sound. . . . . 18 Selecting an input signal. . . . . . . . . 18 Searching an input signal . . . . . . . . 20 Selecting an aspect ratio. . . . . . . . . 20 Adjusting the projector's elevator . . 21 Adjusting the zoom and focus. . . . . 21 Using the automatic adjustment feature. . . 22 Adjusting the position . . . . . . . . . . . 22 Correcting the keystone distortions. . 23 Using the magnify feature. . . . . . . . 24 Temporarily freezing the screen . . . 25 Temporarily blanking the screen . . 25 Using the menu function . . . . . . . . 26

EASY MENU. . . . . . . . . . . . . . . 28

ASPECT, AUTO KEYSTONE , KEYSTONE, PICTURE MODE, ECO MODE, MIRROR, RESET, FILTER TIME, LANGUAGE, ADVANCED MENU, EXIT

PICTURE menu . . . . . . . . . . . . 30

BRIGHTNESS, CONTRAST, GAMMA, COLOR TEMP, COLOR, TINT, SHARPNESS, ACTIVE IRIS, MY MEMORY

IMAGE menu . . . . . . . . . . . . . . 33

ASPECT, OVER SCAN, V POSITION, H POSITION, H PHASE, H SIZE, AUTO ADJUST EXECUTE

INPUT menu . . . . . . . . . . . . . . 36

PROGRESSIVE, VIDEO NR, COLOR SPACE, COMPONENT, VIDEO FORMAT, HDMI FORMAT, HDMI RANGE, COMPUTER IN,

FRAME LOCK, RESOLUTION

VOLUME, SPEAKER, AUDIO SOURCE,

HDMI AUDIO, MIC LEVEL, MIC VOLUME

SCREEN menu. . . . . . . . . . . . . 44

LANGUAGE, MENU POSITION, BLANK,

START UP, MyScreen, MyScreen Lock,

MESSAGE, SOURCE NAME, TEMPLATE, C.C.

OPTION menu . . . . . . . . . . . . . 50

AUTO SEARCH, AUTO KEYSTONE, DIRECT POWER ON, AUTO POWER OFF, USB TYPE B, LAMP TIME, FILTER TIME, MY BUTTON, MY SOURCE, SERVICE

NETWORK menu . . . . . . . . . . . 60

SETUP, PROJECTOR NAME, MY IMAGE, AMX D.D., PRESENTATION, INFORMATION, SERVICE

SECURITY menu . . . . . . . . . . . 67

SECURITY PASSWORD CHANGE,

MyScreen PASSWORD, PIN LOCK,

TRANSITION DETECTOR, MY TEXT PASSWORD, MY TEXT DISPLAY, MY TEXT WRITING

Presentation tools . . . . . . . . . 73 PC-LESS Presentation . . . . . . . 73 Thumbnail Mode, Full Screen Mode, Slideshow mode, Playlist

USB Display . . . . . . . . . . . . . 82

Right-Click menu, Floating menu, Options window

Maintenance . . . . . . . . . . . . . . 85

Replacing the lamp . . . . . . . . . . . . . 85 Cleaning and replacing the air filter . . 87

Replacing the internal clock battery . . 89 Other care. . . . . . . . . . . . . . . . . . . . 90

Troubleshooting . . . . . . . . . . . 91

Related messages . . . . . . . . . . . . . 91 Regarding the indicator lamps . . . . 93 Shutting the projector down . . . . . . 94 Resetting all settings. . . . . . . . . . . . 94 Phenomena that may be easy

to be mistaken for machine defects. . 95

Specifications . . . . . . . . . . . . . 99

2

Introduction

Introduction

Features

The projector provides you with the broad use by the following features.

This projector has a variety of I/O ports that supposedly cover for any business scene. The HDMI port can support various image equipment which have digital interface to get clearer pictures on a screen.

This projector realizes the large projection image, even if in a small space.

If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the device.

This projector can be controlled and monitored via LAN connection.

This projector's network supports the PJLinkTM standard.

PJLinkTM is a unified standard for operating and controlling data projectors.

PJLinkTM enables central control of projectors manufactured by different vendors and projectors can be operated by a controller. PJLinkTM compliant equipment can be managed and controlled at any time and in any place, regardless of manufacturer.

For the command of PJLinkTM, see “Technical”.

For specifications of PJLinkTM, see the web site of the Japan Business Machine and Information System Industries Association.

URL: http://pjlink.jbmia.or.jp (as of Dec. 2009)

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise) which is a book. Your projector should come with the items shown there. Require of your dealer immediately if any items are missing.

NOTE • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector. Use special caution for the lens.

3

Introduction

Part names

Projector

(1) Lamp cover (85)

The lamp unit is inside.

(2)Focus ring (21)

(3)Zoom ring (21)

(4)Control panel (5)

(5)Elevator buttons (x 2) (21)

(6)Elevator feet (x 2) (21)

(7)Remote sensor (15)

(8)Lens (90)

(9)Intake vents

(10)Filter cover (87)

The air filter and intake vent are inside.

(11) Battery cover

The internal clock battery is inside.

(12)Speaker (12, 18, 42)

(13)Exhaust vent

(14)AC IN (AC inlet) (14)

(15)Rear panel (5)

(16)Security bar (14)

(17)Security slot (14)

(18)Shutdown switch (94)

HOT! (1)

(2) (3) (4)

			(12)
	(6)		(7)
	(9)	(8)	(5)
			(6)
		(10)
		(6)

(11)

(6)

(12)

HOT! (13)

(18)	(4)	(15)	HOT!
		(1)

(16) (14)

(17)

(15)

HOT! (13)

WARNING ►HOT! : Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes.

►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

CAUTION ►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air filter periodically.

►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

4

Introduction

Control panel
(1)	STANDBY/ON button ( 17)			(5)	(6)
(2)	INPUT button ( 18)
(3)	MENU button ( 26)
	It consists of four cursor buttons.
(4)	POWER indicator ( 17, 93, 94)
(5)	TEMP indicator ( 93, 94)
(6)	LAMP indicator ( 93, 94)	(1)	(2)	(3)	(4)

Rear panel (9 ~ 13)

(1)	USB TYPE A port			(10)	COMPUTER IN1 port
(2)	LAN port			(11) COMPUTER IN2 port
(3)	HDMI port			(12)	MONITOR OUT port
(4)	USB TYPE B port			(13)	CONTROL port
(5)	MIC port			(14)	VIDEO port
(6)	AUDIO IN1 port			(15)	S-VIDEO port
(7)	AUDIO IN2 port			(16)	Cr/Pr,Cb/Pb,Y
(8)	AUDIO IN3(L,R) ports				(Component) ports
(9)	AUDIO OUT (L,R) ports
	(1)	(3)	(4)	(10)	(11)	(12)

	USB	HDMI
(2)	TYPE A	USB
	DC5V 0.5A	TYPE B

LAN

(5)

MIC

IN1

IN2

(6) (7) (8) (9) (16) (15) (14) (13)

CAUTION ►Use the shutdown switch only when the projector is not turned off by normal procedure, since pushing this switch stops operation of the projector without cooling it down.

5

Introduction

Remote control

(1)VIDEO button (19)

(2)COMPUTER button (19)

(3)SEARCH button (20)

(4)STANDBY/ON button (17)

(5)ASPECT button (20)

(6)AUTO button (22)

(7)BLANK button (25)

(8)MAGNIFY - ON button (24)

(9)MAGNIFY - OFF button (24)

(10)MY SOURCE/DOC.CAMERA button (19, 54)

(11)VOLUME - button (18)

(12)PAGE UP button (16)

(13)PAGE DOWN button (16)

(14)VOLUME + button (18)

(15)MUTE button (18)

(16)FREEZE button (25)

(17)MY BUTTON - 1 button (53)

(18)MY BUTTON - 2 button (53)

(19)KEYSTONE button (23)

(20)POSITION button (22, 27)

(21)MENU button (26, 27)

(22)▲/▼/◄/► cursor buttons (26, 27)

(23)ENTER button (26, 27)

(24)ESC button (27)

(25)RESET button (27)

(26)Battery cover (15)

(2)					(10)
(1)					(4)
(6)	VIDEO		MY SOURCE/		(3)
(5)		COMPUTER DOC.CAMERA			(7)
	ASPECT	AUTO	SEARCH	BLANK
(16)	MAGNIFY	FREEZE	UP	VOLUME	(12)
			PAGE
(8)	ON				(14)
	OFF		DOWN
(9)					(11)
(19)	KEYSTONE	MY BUTTON		MUTE	(13)
		1	2
(17)					(15)
(20)	POSITION			MENU	(18)
(22)		ENTER			(21)
	ESC			RESET	(23)
(24)					(25)

(26)

Back of

the remote control

6

Setting up

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1024 x 768 a Screen size (diagonal) b Projection distance (±10%)

c1 , c2 Screen height (±10%)

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

• For the case of installation in a special state such as ceiling mount, the specified mounting accessories (99) and service may be required. Before installing the projector, consult your dealer about your installation.

	a							4 : 3 screen										16 : 9 screen
						b			c1				c2					b			c1			c2
Screen size
(diagonal)				Projection distance					Screen			Screen				Projection distance				Screen			Screen
				min.			max.		height			height				min.		max.		height			height
type		m		m	inch		m	inch	cm		inch	cm		inch		m	inch	m	inch	cm		inch	cm		inch
(inch)
30		0.8		0.9	34		1.0	41	41		16	5		2		1.0	38	1.1	45	39		15	-1		0
40		1.0		1.2	46		1.4	55	55		22	6		2		1.3	51	1.5	60	51		20	-2		-1
50		1.3		1.5	58		1.8	69	69		27	8		3		1.6	64	1.9	76	64		25	-2		-1
60		1.5		1.8	70		2.1	83	82		32	9		4		1.9	77	2.3	91	77		30	-2		-1
70		1.8		2.1	82		2.5	97	96		38	11		4		2.3	90	2.7	106	90		35	-3		-1
80		2.0		2.4	94		2.8	112	110		43	12		5		2.6	103	3.1	122	103		41	-3		-1
90		2.3		2.7	106		3.2	126	123		49	14		5		2.9	116	3.5	137	116		46	-4		-1
100		2.5		3.0	118		3.6	140	137		54	15		6		3.3	129	3.9	153	129		51	-4		-2
120		3.0		3.6	142		4.3	168	165		65	18		7		3.9	155	4.7	183	154		61	-5		-2
150		3.8		4.5	178		5.3	211	206		81	23		9		4.9	194	5.8	229	193		76	-6		-2
200		5.1		6.0	237		7.1	281	274		108	30		12		6.6	259	7.8	306	257		101	-8		-3
250		6.4		7.5	297		8.9	352	343		135	38		15		8.2	324	9.7	383	322		127	-10		-4
300		7.6		9.1	357		10.7	422	411		162	46		18		9.9	389	11.7	460	386		152	-12		-5

(continued on next page)

7

Setting up

Arrangement (continued)

WARNING ►Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in fire and/or electric shock.

•Do not place the projector on an unstable, slanted or vibrational surface such as a wobbly or inclined stand.

•Do not place the projector on its side, front or rear position.

•Consult with your dealer before a special installation such as suspending from a ceiling or somewhere else.

►Place the projector in a cool place, and ensure that there is sufficient ventilation. The high temperature of the projector could cause fire, burns and/or malfunction of the projector.

•Do not stop-up, block or otherwise cover the projector's vents.

•Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

•Do not place or attach anything that would block the lens or vent holes.

•Do not place the projector on metallic thing or anything weak in heat.

•Do not place the projector on carpet, cushions or bedding.

•Do not place the projector in direct sunlight or near hot objects such as heaters.

•Do not place anything near the projector lens or vents, or on top of the projector.

•Do not place anything that may be sucked into or stick to the vents on the bottom of the projector. This projector has some intake vents also on the bottom.

►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause fire, electric shock and/or malfunction of the projector.

•Do not place the projector in a bathroom or the outdoors.

•Do not place anything containing liquid near the projector.

►Use only the mounting accessories the manufacturer specified, and leave installing and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION ►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause fire, electric shock and/or malfunction of the projector.

• Do not place the projector near humidifiers, smoking spaces or a kitchen. ►Position the projector to prevent light from directly hitting the projector's remote sensor.

►Do not place the product in a place where radio interference may be caused. ►Do not place this product in a magnetic field.

8

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to confirm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or the accessory is damaged.

After making sure that the device and projector are turned off, connect them following the instructions below.

WARNING ►Use only the appropriate accessories. Otherwise it could cause a fire or damage to the device and the projector.

-Use only the accessories specified or recommended by the projector’s manufacturer. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. It may be regulated under some standard.

-For a cable with a core at only one end, connect the end with the core to the projector. That may be required by EMI regulations.

-Neither disassemble nor modify the projector and the accessories.

-Do not use the damaged accessory. Be careful not to damage the accessories. Route a cable so that it is neither stepped on nor pinched out.

CAUTION ►Do not turn on or off the projector while connected to a device in operation, unless that is directed in the manual of the device. Otherwise it may cause malfunction in the device or projector.

►Be careful not to mistakenly connect a connector to a wrong port. Otherwise it may cause malfunction in the device or projector.

-When connecting a connector to a port, make sure that the shape of the connector fits the port.

-Tighten the screws to connect a connector equipped with screws to a port.

-Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed.

About Plug-and-Play capability

• Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.

-Take advantage of this feature by connecting a computer cable to the COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

-Please use the standard drivers in your computer as this projector is a Plug-and- Play monitor.

(continued on next page)

9

Setting up

Connecting with your devices (continued)

•When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in

COMPUTER IN of the INPUT menu, that port will accept component video signals (38).

•When the USB TYPE B port and the computer's type A USB port are connected,

you can use the USB TYPE B port as a picture input port from the computer, or use the remote control as a simple mouse and keyboard of the computer. (16, 51).

VCR/DVD/Blu-ray Disc	Computer
player

COMPONENT

Y Cb/Pb Cr/Pr

AUDIO OUT	R
	L

VIDEO

AUDIO OUT	L
	R

S-VIDEO

USB	HDMI				COMPUTER IN1
		USB
TYPE A		TYPE B
DC5V 0.5A	LAN				VIDEO
	MIC	AUDIO		Cr/Pr	S-VIDEO
	IN1	L	L
				Cb/Pb
		IN3	OUT
	IN2
		R	R	Y

R L

OUT

AUDIO

MONITOR OUT

	HDMI
IN2	OUT	AUDIO
	(A)	USB
COMPUTER
	DISPLAY

CONTROL	-RS
	232C

(continued on next page)

10

Setting up

Connecting with your devices (continued)

NOTE • Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector.

-Some signal may need an adapter to input this projector.

-Some computers have multiple screen display modes that may include some signals which are not supported by this projector.

-Although the projector can display signals with resolution up to UXGA (1600X1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the

resolutions of the input signal and the projector panel are identical.

•If you connect this projector and a notebook computer, you need output the display to an external monitor, or output simultaneously to the internal display and an external monitor. Consult the computer's manual for the setting.

•Depending on the input signal, the automatic adjustment function of this

projector may take some time and not function correctly.

-Note that a composite sync signal or sync-on-green signal may confuse the automatic adjustment function of this projector (38).

-If the automatic adjustment function does not work correctly, you may not see the dialog to set the display resolution. In such a case, use an external display device. You may be able to see the dialog and set an appropriate display resolution.

(continued on next page)

11

Setting up

Connecting with your devices (continued)

•If you insert a USB storage device, such as a USB memory, into the USB TYPE

A port and select the port as the input source, you can view images stored in the device (73).

•You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug. In that case, the built-in speaker outputs the sound from the microphone, even while the sound from the projector is output. You can input line level signal to the MIC port from equipment such as wireless microphone. Select HIGH in the MIC LEVEL item of the AUDIO menu when you input line level audio signal to the MIC port. The volume of the microphone and that of the sound from the projector can be controlled separately except for the standby mode. However, if you mute the sound from the projector, the sound from the microphone is also muted.

Speakers

	(with an amplifier)
Microphone system	R	L
USB storage
device

USB	HDMI	COMPUTER IN1
	USB
TYPE A	TYPE B
DC5V 0.5A		VIDEO
LAN

Monitor

RGB IN

COMPUTER

IN2

MONITOR OUT

	MIC	AUDIO		Cr/Pr S-VIDEO	CONTROL
	IN1	L	L
				Cb/Pb
		IN3	OUT
	IN2
		R	R	Y

CAUTION ►Before removing the USB storage device from the port of the projector, be sure to use the REMOVE USB function on the thumbnail screen to secure your data (76).

NOTE • If a loud feedback noise is produced from the speaker, move the microphone away from the speaker.

• This projector doesn't support plug-in power for the microphone.

(continued on next page)

12

Setting up

Connecting with your devices (continued)

To use network functions of the projector, connect the LAN port with the computer's LAN port, or with an access point that is connected to the computer with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, also connect the CONTROL port and an RS-232C port of the external device to

communicate as a network terminal. See the User's Manual - Network Guide for details of the network functions.

Access point

Computer

LAN RS-232C

COMPUTER

USB

HDMI

IN2

USB

COMPUTER IN1

TYPE A

TYPE B

DC5V 0.5A

VIDEO

LAN

MONITOR

OUT

	MIC		AUDIO				S-VIDEO	CONTROL
						Cr/Pr
	IN1		L	L
						Cb/Pb
			IN3	OUT
	IN2
			R	R		Y

CAUTION ►Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network (60).

►Do not connect the LAN port to any network that might have the excessive voltage.

NOTE • If an oversized USB storage device blocks the LAN port, use a USB extension cable to connect the USB storage device.

13

Setting up

Connecting to a power supply

1. Put the connector of the power cord into the AC IN (AC inlet) of the projector.

2. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

Please remember that when the DIRECT POWER
ON function activated ( 50), the connection of the	AC IN	Power cord
power supply make the projector turn on.

WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock.

•Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one.

•Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

•Never modify the power cord.

Using the security bar and slot

A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector.

Also this product has the security slot for the Kensington lock.

For details, see the manual of the security tool.

Anti-theft chain or wire

Security slot

Security bar

WARNING ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

CAUTION ►Do not place anti-theft chain or wire near the exhaust vents. It may become too hot.

NOTE • The security bar and slot is not comprehensive theft prevention measures. It is intended to be used as supplemental theft prevention measure.

14

Remote control

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

		Holding the hook part of the battery	1	2	3
	1. cover, remove it.
	2.	Align and insert the two AA batteries
		(HITACHI MAXELL, Part No.LR6 or R6P)
		according to their plus and minus terminals
	3.	as indicated in the remote control.
		Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

•Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•Make sure the plus and minus terminals are correctly aligned when loading a battery.

•Keep a battery away from children and pets.

•Do not recharge, short circuit, solder or disassemble a battery.

•Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.

•If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

•Obey the local laws on disposing the battery.

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

Approx.

3 m 30º 30º

NOTE • The remote control signal reflected in the screen or the like may be available. If it is difficult to send the signal to the sensor directly, attempt to make the signal reflect.

•The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter fluorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

15

Remote control

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control				MY SOURCE/
		VIDEO	COMPUTER DOC.CAMERA
does not function properly, attempt to change the signal frequency.		ASPECT	AUTO	SEARCH	BLANK
		MAGNIFY	FREEZE	PAGE	VOLUME
In order to set the Mode, please keep pressing the combination of		ON		UP
two buttons listed below simultaneously for about 3 seconds.		KEYSTONE		DOWN	MUTE
			MY BUTTON
	(2)	OFF				(1)
(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons			1	2
(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons		POSITION			MENU
Please remember that the REMOTE FREQ. in the SERVICE item of			ENTER
the OPTION menu ( 56) of the projector to be controlled should be		ESC			RESET
set to the same mode as the remote control.

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s USB TYPE B port and the computer’s type A USB port are connected and MOUSE is selected for the USB TYPE B item in the OPTION menu ( 51).

(1)PAGE UP key: Press PAGE UP button.

(2)PAGE DOWN key: Press PAGE DOWN button.

(3)Mouse left button: Press ENTER button.

(4)Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.

(5)ESC key: Press ESC button.

(6)Mouse right button: Press RESET button.

USB

TYPE B

USB port

WARNING ►Improper use of the simple mouse &

(3)

keyboard function could damage your equipment. While using this function, please connect this product only to

a computer. Be sure to check your computer’s manuals	(5)
before connecting this product to the computer.

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME

UP

ON

OFF	DOWN
KEYSTONE	MY BUTTON	MUTE
	1	2
POSITION		MENU
	ENTER
ESC		RESET

(1)

(2)

(4)

(6)

NOTE • When the simple mouse & keyboard function of this product does not work correctly, please check the following.

-When a USB cable connects this projector with a computer having a built-in pointing device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

-Windows 95 OSR 2.1 or higher is required for this function. And also this function may not work depending on the computer’s configurations and mouse drivers. This function can work with the computer which can operate general USB mouse or keyboard.

-You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

-This function is activated only when the projector is working properly. This function is not available while the lamp is warming up (the POWER indicator blinks green), and while adjusting the volume and display, correcting for keystone, zooming in on the screen, using the BLANK function, or displaying the menu screen.

16

Power on/off

Power on/off

Turning on the power	STANDBY/ON button
Make sure that the power cord is firmly and	POWER indicator
1. correctly connected to the projector and the
outlet.
Make sure that the POWER indicator is
2. steady orange ( 93). Then remove the lens
cover.	VIDEO		MY SOURCE/
		COMPUTER DOC.CAMERA
	ASPECT	AUTO	SEARCH	BLANK
	MAGNIFY	FREEZE	PAGE	VOLUME
Press STANDBY/ON button on the	ON		UP
	OFF		DOWN
	KEYSTONE	MY BUTTON1 2		MUTE
3. projector or the remote control.	POSITION			MENU
The projection lamp will light up and POWER		ENTER
	ESC			RESET

indicator will begin blinking in green. When the

power is completely on, the indicator will stop blinking and light in steady green (93).

To display the picture, select an input signal according to the section “Selecting an input signal” (18).

Turning off the power

1. Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds.

2. Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (93).

3. Attach the lens cover, after the POWER indicator turns in steady orange.

Do not turn the projector on for about 10 minutes or more after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices.

•This projector has the function that can make the projector automatically turn on/ off. Please refer to the DIRECT POWER ON (50) and AUTO POWER OFF (51) items of the OPTION menu.

•Use the shutdown switch (94) only when the projector is not turned off by normal procedure.

17

Operating

Operating

Adjusting the volume

VOLUME +/- button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

1. Use the VOLUME +/VOLUME - buttons to adjust the volume. A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds.

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

1 2

●When is selected for current picture input port, the volume adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (42).

●Even if the projector is in the standby state, the volume is adjustable when both of the following conditions are true:

-An option other than is selected for STANDBY in the AUDIO SOURCE item of the AUDIO menu (42).

-NORMAL is selected in the STANDBY MODE item of the SETUP menu (42).

Temporarily muting the sound

1. Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound.

To restore the sound, press the MUTE, VOLUME + or VOLUME - button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

MUTE button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

1 2

●When is selected for current picture input port, the sound is always muted. Please see AUDIO SOURCE item of AUDIO menu (42).

●C.C. (Closed Caption) is automatically activated when sound is muted and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPONENT,

COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (49).

Selecting an input signal

1.	Press INPUT button on the projector.	INPUT button
	Each time you press the button, the projector switches its
	input port from the current port as below.
	COMPUTER IN1 COMPUTER IN2 LAN
	VIDEO	USB TYPE A

S-VIDEO

COMPONENT (Y, Cb/Pb, Cr/Pr)

USB TYPE B HDMI

●While ON is selected for AUTO SEARCH item in OPTION menu (50), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

●It may take several seconds to project the images from the USB TYPE B port.

(continued on next page) 18

Operating

Selecting an input signal (continued)

1.	Press COMPUTER button on the remote control.			COMPUTER button
	Each time you press the button, the projector switches its
	input port from the current port as below.				VIDEO	COMPUTER DOC.CAMERA
	COMPUTER IN1 COMPUTER IN2 LAN						MY SOURCE/
					ASPECT	AUTO	SEARCH	BLANK
	USB TYPE B		USB TYPE A		MAGNIFY	FREEZE	PAGE	VOLUME
					ON		UP
● While ON is selected for AUTO SEARCH item in OPTION					OFF		DOWN
					KEYSTONE	MY BUTTON		MUTE
	menu, the projector will keep checking every port sequentially					1	2
	till an input signal is detected ( 50). If COMPUTER button is				POSITION			MENU

pressed when VIDEO, S-VIDEO, COMPONENT or HDMI port is selected, the projector will check COMPUTER IN1 port first.

● It may take several seconds to project the images from the

USB TYPE B port.

1. Press VIDEO button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

HDMI COMPONENT (Y, Cb/Pb, Cr/Pr) S-VIDEO

VIDEO

●While ON is selected for AUTO SEARCH item in OPTION

menu, the projector will keep checking every port sequentially till an input signal is detected (50). If VIDEO button is pressed when COMPUTER IN1 or COMPUTER IN2 port is selected, the projector will check HDMI port first.

VIDEO button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME

UP

ON

OFF	DOWN
KEYSTONE	MY BUTTON	MUTE
	1	2
POSITION		MENU

Press the MY SOURCE / DOC. CAMERA button on	MY SOURCE /
1. the remote control. The input signal will be changed	DOC. CAMERA button
into the signal you set as MY SOURCE ( 54).

●This function also can use for document camera. Select the input port that connected the document camera.

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

12

POSITION

MENU

19

Operating

Searching an input signal

1. Press SEARCH button on the remote control.

The projector will start to check its input ports as below in order to find any input signals.

When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN1 COMPUTER IN2 LAN

VIDEO	USB TYPE A
S-VIDEO	USB TYPE B

COMPONENT (Y, Cb/Pb, Cr/Pr) HDMI

SEARCH button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME

UP

ON

OFF	DOWN
KEYSTONE	MY BUTTON	MUTE
	1	2
POSITION		MENU

●While ON is selected for AUTO SEARCH item in OPTION menu (50), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

●It may take several seconds to project the images from the USB TYPE B port.

Selecting an aspect ratio

1. Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

ASPECT button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

For a computer signal

NORMAL 4:3 16:9 16:10

For an HDMI signal

NORMAL 4:3 16:9 16:10 14:9

MAGNIFY FREEZE PAGE VOLUME UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

12

POSITION

MENU

For a video signal, s-video signal or component video signal

4:3 16:9 14:9

For an input signal from the LAN, USB TYPE A or USB TYPE B port, or if there is no signal

4:3 (fixed)

●ASPECT button does not work when no proper signal is inputted.

●NORMAL mode keeps the original aspect ratio setting.

20

Operating

Adjusting the projector's elevator

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally.

Using the feet can also tilt the projector in order to project at

a suitable angle to the screen, elevating the front side of the 14° projector within 14 degrees.

This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable while pushing the elevator button on the same side as it.

1. Holding the projector, push the elevator buttons to loose the elevator feet.

2. Position the front side of the projector to the desired height.

3. Release the elevator buttons in order to lock the elevator feet.

4. After making sure that the elevator feet are locked, put the projector down gently.

5. If necessary, the elevator feet can be manually twisted to make more precise adjustments. Hold the projector when twisting the feet.

1

5

To loose an elevator foot, push the elevator button on the same side as it.

To finely adjust, twist the foot.

CAUTION ►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

►Do not tilt the projector other than elevating its front within 14 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

Adjusting the zoom and focus

1.

2.

Zoom ring

Use the zoom ring to adjust the screen size.

Focus ring

Use the focus ring to focus the picture.

21

POSITION button

Operating

Using the automatic adjustment feature

1.	Press AUTO button on the remote control.	AUTO button
	Pressing this button performs the following.

For a computer signal

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted.

Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

12

For a video signal and s-video signal

The video format best suited for the respective input signal will be selected

automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu ( 37). The vertical position and horizontal position will be automatically set to the default.

For a component video signal

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

●The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

●When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

●When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model.

●The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (55).

Adjusting the position

1. Press POSITION button on the remote control when no menu is indicated.

The “POSITION” indication will appear on the screen.

2. Use the ▲/▼/◄/► cursor buttons to adjust the picture position. When you want to reset the operation, press RESET button on the remote control during the operation.

To complete this operation, press POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

KEYSTONE

MY BUTTON

MUTE

12

POSITION	MENU
	ENTER
ESC	RESET

●When this function is performed on a video signal or an s-video signal, some image such as an extra-line may appear at outside of the picture.

●When this function is performed on a video signal or s-video signal, the range of this adjustment depends on OVER SCAN in IMAGE menu ( 33) setting. It is not possible to adjust when OVER SCAN is set to 10.

●If POSITION button is pressed when a menu is indicated on screen, the displayed picture does not move its position but the menu does.

●This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE B

or HDMI port.

22

Operating

Correcting the keystone distortions

1. Press KEYSTONE button on the remote control. A dialog will appear on the screen to aid you in correcting the distortion.

2. Use the ▲/▼ cursor buttons to select AUTO or MANUAL operation, and press the ► button to perform the following.

(1)AUTO executes automatic vertical keystone correction.

(2)MANUAL displays a dialog for keystone correction. Use the ◄/► buttons for adjustment.

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

KEYSTONE button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME

UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

1 2

●The adjustable range of this function will vary among inputs. For some input, this function may not work well.

●When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, automatic vertical keystone correction may not work correctly.

●When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

●When the projector is placed on the level (about ±4°), the automatic keystone distortion correction may not work.

●When the projector is inclined to near ±30 degree or over, this function may not work well.

●This function will be unavailable when Transition Detector is on (70).

23

Operating

Using the magnify feature

1. Press the MAGNIFY ON button on the remote control. The picture will be magnified, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the first time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed.

MAGNIFY ON/OFF button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME

UP

ON

DOWN

OFF

2.

3.

4.

5.

While the triangles are displayed on the dialog, use the	KEYSTONE MY BUTTON	MUTE
	1	2
▲/▼/◄/► cursor buttons to shift the magnifying area.

A magnifying glass icon will be displayed on the dialog when the MAGNIFY ON button is pressed while the dialog with the triangles is displayed.

While the magnifying glass icon is displayed on the dialog, use the ▲/▼ cursor buttons to adjust the magnification ratio. The magnification ratio will be adjusted with fine steps. And changes in the ratio in single steps are subtle so they may be hard to recognize.

Press the MAGNIFY OFF button on the remote control to exit magnification.

●The MAGNIFY dialog will automatically disappear in several seconds with no operation. The dialog will appear again if the MAGNIFY ON button is pressed when the dialog has automatically disappeared.

●While the MAGNIFY dialog is displayed, press the MAGNIFY ON button to switch the dialog between magnifying area shifting (with the triangles) and magnification ratio adjustment (with the magnifying glass icon).

●The magnification is automatically disabled when the displaying signal or its display condition is changed.

●While the magnification is active, the keystone distortion condition may vary. It will be restored when the magnification is disabled.

●Some horizontal stripes might be visible on the image while magnification is active.

●This function is not available in the following cases:

-The USB TYPE A port is selected as the input source.

-A sync signal in the range not supported is input.

-There is no input signal.

24

Operating

Temporarily freezing the screen

FREEZE button

1. Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however, the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu (46)), and the projector will go into the FREEZE mode, which the picture is frozen.

To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

12

●The projector automatically exits from the FREEZE mode when some control buttons are pressed.

●If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

●Images might appear degraded when this function is operated, but it is not a malfunction.

Temporarily blanking the screen

1. Press BLANK button on the remote control.

The BLANK screen will be displayed instead of the screen of

input signal. Please refer to BLANK item in SCREEN menu (44).

To exit from the BLANK screen and return to the input signal screen, press BLANK button again.

●The projector automatically exits from the BLANK mode when some control buttons are pressed.

BLANK button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGE VOLUME

UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

1 2

CAUTION ►If you wish to have a blank screen while the projector's lamp is on, use one of methods below.

-Use the supplied lens cover.

-Use the BLANK function above.

Taking any other action may cause the damage on the projector.

NOTE • The sound is not connected with the BLANK screen function. If necessary, set the volume or mute first. To display the BLANK screen and mute the sound at one time, use AV MUTE function (53).

25

Operating

Using the menu function

This projector has the following menus:

PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, SECURITY and EASY MENU.

EASY MENU consists of functions often used, and the other menus are classified into each purpose and brought together as the ADVANCED MENU.

Each of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these menus are as follows.

ENTER button	MENU button
Cursor buttons
POSITION	MENU	MY SOURCE/
	VIDEO COMPUTER DOC.CAMERA
	ASPECT AUTO	SEARCH	BLANK
	MAGNIFY FREEZE	PAGE	VOLUME
		UP
	ON
	OFF	DOWN
ENTER	1	2	MUTE
	KEYSTONE MY BUTTON

MENU button (Cursor buttons)

ESC

RESET

POSITION	MENU
	ENTER
ESC	RESET

ESC button

RESET button

1. To start the MENU, press the MENU button. The MENU you last used (EASY or ADVANCED) will appear. EASY MENU has priority to appear just after powered on.

2. In the EASY MENU

(1)Use the ▲/▼ cursor buttons to select an item to operate. If you want to change it to the ADVANCED MENU, select the ADVANCED MENU.

(2)Use the ◄/► cursor buttons to operate the item.

In the ADVANCED MENU

(1)Use the ▲/▼ cursor buttons to select a menu. If you want to change it to the EASY MENU, select the EASY MENU.

The items in the menu appear on the right side.

(2)Press the ► cursor button or ENTER button to move the cursor to the right side. Then use the

▲/▼ cursor buttons to select an item to operate and press the ► cursor button or ENTER button to progress. The operation menu or dialog of the selected item will appear.

(3)Use the buttons as instructed in the OSD to operate the item.

(continued on next page)

26

Operating

Using the menu function (continued)

3. To close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds.

●If you want to move the menu position, use the cursor buttons after pressing the

POSITION button.

●Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.

●When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, VOLUME) cannot be reset.

●In the ADVANCED MENU, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control.

Indication in OSD (On Screen Display)

The meanings of the general words on the OSD are as follows.

	Indication	Meaning
	EXIT	Selecting this word finishes the OSD menu. It's the same as
		pressing the MENU button.
	RETURN	Selecting this word returns the menu to the previous menu.
	CANCEL or NO	Selecting this word cancels the operation in the present
		menu and returns to the previous menu.
	OK or YES	Selecting this word executes the prepared function or shifts
		the menu to the next menu.

27

EASY MENU

EASY MENU

From the EASY MENU, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table.

	Item		Description
	ASPECT	Using the ◄/► buttons switches the mode for aspect ratio.
		See the ASPECT item in IMAGE menu ( 33).
	AUTO KEYSTONE	Using the ► button executes the auto keystone function.
		See the AUTO KEYSTONE (EXECUTE) item in SETUP menu ( 40).
	KEYSTONE	Using the ◄/► buttons corrects the vertical keystone distortion.
		See the KEYSTONE item in SETUP menu ( 40).
		Using the ◄/► buttons switches the picture mode.
		The picture modes are combinations of GAMMA and COLOR TEMP
		settings. Choose a suitable mode according to the projected source.
		NORMAL CINEMA DYNAMIC BOARD(BLACK)
		DAYTIME WHITEBOARD BOARD(GREEN)
			GAMMA	COLOR TEMP
		NORMAL	1 DEFAULT	2 MID
		CINEMA	2 DEFAULT	3 LOW
	PICTURE MODE	DYNAMIC	3 DEFAULT	1 HIGH
		BOARD(BLACK)	4 DEFAULT	4 Hi-BRIGHT-1
		BOARD(GREEN)	4 DEFAULT	5 Hi-BRIGHT-2
		WHITEBOARD	5 DEFAULT	2 MID
		DAYTIME	6 DEFAULT	6 Hi-BRIGHT-3

•When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the

PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and COLOR TEMP ( 30, 31) items in PICTURE menu.

•Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction.

(continued on next page)

28

EASY MENU

	Item	Description
	ECO MODE	Using the ◄/► buttons turns off/on the Eco mode.
		See the ECO MODE item in SETUP menu ( 41).
	MIRROR	Using the ◄/► buttons switches the mode for mirror status.
		See the MIRROR item in SETUP menu ( 41).

Performing this item resets all of the EASY MENU items except the

RESET

FILTER TIME and LANGUAGE.

A dialog is displayed for confirmation. Selecting the OK using the ► button performs resetting.

The usage time of the air filter is shown in the menu.

Performing this item resets the filter time which counts usage time

FILTER TIME

of the air filter.

A dialog is displayed for confirmation. Selecting the OK using the ► button performs resetting.

See the FILTER TIME item in OPTION menu ( 52).

	LANGUAGE	Using the ◄/► buttons changes the display language.
		See the LANGUAGE item in SCREEN menu ( 44).

Press the ► or ENTER button to use the menu of PICTURE, ADVANCED MENU IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or

SECURITY.

EXIT	Press the ◄ or ENTER button to finish the OSD menu.

29

PICTURE menu

PICTURE menu

From the PICTURE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item	Description

BRIGHTNESS

Using the ◄/► buttons adjusts the brightness.

Dark Light

CONTRAST

Using the ◄/► buttons adjusts the contrast.

Weak Strong

Using the ▲/▼ buttons switches the gamma mode.

1 DEFAULT 1 CUSTOM 2 DEFAULT 2 CUSTOM 3 DEFAULT

6 CUSTOM	3 CUSTOM

6 DEFAULT 5 CUSTOM 5 DEFAULT 4 CUSTOM 4 DEFAULT

		To adjust CUSTOM
		Selecting a mode whose name includes CUSTOM and then
		pressing the ► button or the ENTER button displays
		a dialog to aid you in adjusting the mode.
		This function is useful when you want to
		change the brightness of particular tones.
		Choose an item using the ◄/► buttons,
	GAMMA	and adjust the level using the ▲/▼ buttons.
		You can display a test pattern for checking the effect of your
		adjustment by pressing the ENTER button.
		Each time you press the ENTER button, the
		pattern changes as below.
		No pattern Gray scale of 9 steps
		Ramp Gray scale of 15 steps
		The eight equalizing bars correspond to eight tone levels of the test
		pattern (Gray scale of 9 steps) except the darkest in the left end. If you
		want to adjust the 2nd tone from left end on the test pattern, use the
		equalizing adjustment bar “1”. The darkest tone at the left end of the
		test pattern cannot be controlled with any of equalizing adjustment bar.
		• Lines or other noise might appear on the
		screen when this function is operated, but it
		is not a malfunction.

(continued on next page)

30