Hikvision DS-2CE57U1T-VPITF-2-8mm, DS-2CE57U1T-VPITF-6mm, DS-2CE76U1T-ITMF-2-8mm, DS-2CE76U1T-ITMF-6mm, DS-2CE78U1T-IT3F-2-8mm User Manual

TURBO HD

U1T Series Turret & Dome

Camera

User Manual

User Manual

Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer.

This manual applies to the models below:

	Type		Model
	Type I Camera		DS-2CE78U1T-IT1F
			DS-2CE78U1T-IT3F
	Type II Camera		DS-2CE76U1T-ITPF
	Type III Camera		DS-2CE76U1T-ITMF
	Type IV Camera		DS-2CE57U1T-VPITF

This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.

0100001080607

Regulatory Information FCC Information

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards

listed under the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new

equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”.

Warnings: Serious injury or death may occur if any of the warnings are neglected.

Cautions: Injury or equipment damage may occur if any of the cautions are neglected.

Warnings Follow	Cautions Follow these
these safeguards to	precautions to prevent
prevent serious injury	potential injury or
or death.	material damage.

Warnings

In the use of the device, you must be in strict compliance with the electrical safety regulations of the nation and region.

Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information.

Do not connect multiple devices to one power adapter to avoid over-heating or a fire hazard caused by overload.

Make sure that the plug is firmly connected to the power socket.

Make sure that the device is firmly fixed if wall mounting or ceiling mounting is adopted.

If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cord, and then contact the service center.

Never attempt to disassemble the camera by unprofessional personal.

Cautions

Do not drop the camera or subject it to physical shock.

Do not place the camera in extremely hot, cold (the operating temperature shall be -40°C to 60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation.

Do not touch senor modules with fingers.

If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.

Do not aim the camera at the sun or extra bright places.

The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.

Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty or damp environment.

To avoid heat accumulation, good ventilation is required for the operating environment.

Keep the camera away from liquid while in use for non- water-proof device.

While in delivery, the camera shall be packed in its original packing, or packing of the same texture.

Mark Description

Table 0-1 Mark Description

Mark Description

DC Voltage

1 Introduction

1.1 Product Features

The main features are as follows:

High performance CMOS sensor

IR cut filter with auto switch

OSD menu with configurable parameters

Auto white balance

Internal synchronization

SMART IR mode

3-axis adjustment

1.2 Overview

This manual applies to three types of turret cameras, and one type of dome camera.

The overviews of each type are shown in the figures below.

1.2.1 Overview of Type I Camera

Enclosure
Main	Switch
Body	Button
	INDC12V	Power Cord
Mounting
Base	Video Cable

Figure 1-1 Overview of Type I Camera

Note:

Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.

1.2.2 Overview of Type II Camera

	Switch Button	Mounting
		Base
	D C1 2V I N
	Power	Main
		Body
	Cord
	Video Cable
		Enclosure
	Figure 1-2 Overview of Type II Camera

Note:

Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.

1.2.3 Overview of Type III Camera
Mounting
Base
Clip Plate
Enclosure
Main Body	Switch
	Button
	Power Cord
	Video
	Cable

Figure 1-3 Overview of Type III Camera

Note:

Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.

1.2.4 Overview of Type IV Camera

		Video Cable
		Power
	Mounting Base	Cord
	Pan Adjusting Screw	Switch
		Button
	Tilt Adjusting
	Screw
	Bubble	Safety
		Rope

Figure 1-4 Overview of Type III Camera

Note:

Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.

2 Installation

Before you start:

 Make sure that the device in the package is in good condition and all the assembly parts are included.

 Make sure that all the related equipment is power-off during the installation.

 Check the specification of the products for the installation environment.

 Check whether the power supply is matched with your required output to avoid damage.

 Make sure the wall is strong enough to withstand three times the weight of the camera and the bracket.

 If the wall is cement, insert expansion screws before installing the camera. If the wall is wooden, use selftapping screw to secure the camera.

 If the product does not work properly, contact your dealer or the nearest service center. Do NOT disassemble the camera for repair or maintenance by yourself.