Wireless Chime
This package includes (Style of push button and chime may vary from illustration):
• |
Wireless chime cover |
• |
Wireless chime base |
• |
Wireless push button w/battery |
• |
Hardware pack |
You'll need to buy 2 “C” alkaline batteries for the chime. In typical use, alkaline batteries will last up to one year.
1.Install alkaline type A23 12 volt push button battery.
Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 3).
2.Remove chime cover (see page 4).
3. Install 2 alkaline “C” batteries. Press in catch on bottom of battery cover and lift to remove. Make sure batteries are oriented properly.
TR-0095-RX
TYPE
C
TYPE
C
Battery Cover
Battery Cover
Catch
4.Test range. Temporarily position chime and push button where you want them mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting.
5.Mount push button. Use either screws or double sided tape to mount push button.
•To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on.
•When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean.
© 2007 HeathCo LLC |
598-1171-03 |
6.Mount chime. Mount door chime in a central location so it can be heard throughout the home.
•See actual unit for orientation of base.
•Always use mounting wall anchors.
•Use all mounting holes located at four corners of base.
Cover Pins
Wall Anchor |
Mounting |
|
(If Needed) |
||
Orientation |
||
|
||
|
Marking |
-TR RX-0095
Mounting Hole 
Screw
Code and Tune Settings
Code Settings
Note: Most installations will not require you to change any jumpers on your chime and push button.
The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime.The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code.
1.Open the cases and locate the jumpers on both the push button and chime (See illustration on page 3).
2.The push button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code.
3.To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly.
Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function.
- - |
598-1171-03 |
Tune Settings
Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below.
•Ding (one note tune)
Push Button: Add a jumper to location 8.
•Ding-Dong (two note tune)
Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8.
•Westminster (Eight note tune) (Available on selected chimes) Push Button: Remove jumper from location 8.
Chime: Add a jumper to location 8.
Note: All models have both front and back door tune capabilities. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting.
Push Button Battery Replacement
Install an alkaline type A23 12 Volt battery. See diagram inside push button for correct orientation of batteries.
Inside Chime
8 7 6 5 4 3 2 1
Tune Setting (Not used on all models)
1 |
* Code Settings 1-7 |
|
2 |
||
Must Match Both Push |
||
3 |
||
Button and Chime |
||
4 |
8 7 6 5
Tune Setting
Inside Push Button
Note: Some models might require the use of tweezers to remove and replace the jumpers.
598-1171-03 |
- - |
Attaching Chime Covers
Snap-On Cover: Apply pressure to the cover until it snaps into place (see Figure A). To remove, firmly grasp cover and pull to remove from base.
Hanging Cover: Before mounting chime base to wall, slide the cover pin that will be on top of the mounted base out of the base. Turn it over so the pin is protruding above the base. Slide the cover pin into base (see Figure B). Hang cover on cover pin.
Note: Cover pins are located on two sides of the chime base for use with hanging covers. When chime base is mounted according to mounting orientation marking, use the cover pin located on the top of the chime base for hanging the cover.
Mounted
Chime Base
TR-0095-RX
Cover Pin
Snap-On |
|
Chime |
|
Base |
|
Cover |
|
|
|
|
|
|
Figure A |
Figure B |
|
|
Troubleshooting
Chime does not sound:
•Make sure push button and chime codes are the same (See pages 2 and 3).
•Check orientation of push button battery (See page 3).
•Check charge of push button and chime batteries, replace if necessary.
Batteries seem OK, but the chime does not work when installed:
•Do not mount chime or push button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or push button off metal surface.
•Concrete floors may reduce range. Move chime away from floor.
•Try locating chime closer to push button.
The range of the wireless chime can vary with location, temperature and battery condition.
- - |
598-1171-03 |
Technical Service
Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store.
If you experience a problem, follow this guide.You may also want to visit our Web site at: www.hzsupport.com. If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:
HeathCo LLC
P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service
* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.
No Service Parts Available for this Product
Regulatory Information
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.
598-1171-03 |
- - |
ONE YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific legal rights.You may also have other rights which vary from state to state or province to province.
For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HeathCo LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for all warranty requests.
HeathCo LLC reserves the right to discontinue and to change specifications at any time without notice without incurring any obligation to incorporate new features in previously sold products.
- - |
598-1171-03 |
Loading...