Heath Zenith SL-6167, SL-6166 User Manual

0 (0)
Heath Zenith SL-6167, SL-6166 User Manual

Models SL-6166 & 6167

Wireless

Plug-In

Doorbell

Your doorbell includes:

Plug-in doorbell chime

Doorbell button/transmitter with battery (model 6167 includes 2)

Hardware pack

Chime

Volume

Control

Access Door

1.Set the chime volume on the back of the plug-in chime, if desired.

2.Plug-in the doorbell chime.

To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

3. Before mounting, test the doorbell range.

Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button.

© 2007 HeathCo LLC

595-5494-11

Operation

Press the doorbell button to verify that the

 

doorbell and chime work properly. If the chime

 

does not sound see the Troubleshooting guide

 

on page 4.

 

4. Mount the doorbell button.

 

Use either screws or double sided tape to mount

Doorbell Button

the doorbell button.

 

Push

Button

To mount with screws, remove the back of the case by pushing in the tab on the bottom with a small screwdriver and rotating the blade.

Attach the back of the case to the door jamb or wall. Snap the front of the button back on.

When attaching the doorbell button using the double sided tape, make sure the surface of the door jamb or wall is clean.

Code and Tune Settings

Code Settings

Note: Most installations will not require you to change any of the jumpers on your doorbell.

WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power.

The doorbell button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the doorbell button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Another wireless doorbell system or other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code.

1. Disconnect the power to the doorbell button and chime.

- -

595-5494-11

2.Open the cases and locate the jumpers on both the doorbell button and chime (See illustration).

3.The doorbell button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code.

4.To change the code, add and/or remove jumpers as needed. There are 128 different combinations. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the doorbell button and chime for this system to function.

Tune Settings

Your Heath®/Zenith wireless doorbell has 3 different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note). The factory setting is for the Westminster; however, this can be changed by following the instructions below.

Ding (one note tune)

Doorbell button: Add a jumper to location 8.

Ding-Dong (two note tune)

Doorbell button: Remove jumper from location 8. Chime: Remove jumper from location 8.

Westminster (Eight note tune)

Doorbell button: Remove jumper from location 8. Chime: Add a jumper to location 8.

Note: Model 6167 has doorbell buttons for both front and back door. The back door must use the Ding tune and the front door may use either the Ding-Dong or Westminster tune.

Remove screw to open access door

Back of

Chime

345678 12

595-5494-11

Doorbell Button Battery Replacement

Install an alkaline type A23 12 Volt battery. The positive terminal should be positioned as shown.

 

12456783

* Code Settings 1-7

 

 

 

 

Must Match Both

 

 

Doorbell Button and

 

 

Chime

Tune

Inside

Note: Some models

Setting

Doorbell

might require the use of

 

Button

tweezers to remove and

 

 

replace the jumpers.

 

- -

 

Troubleshooting

Chime does not sound:

Make sure the doorbell button and the chime codes are the same (See pages 2 and 3).

Check orientation of doorbell button battery (See page 3).

Check the doorbell button battery, replace if necessary.

Batteries seem OK, but the chime does not work when installed:

Do not mount the chime or doorbell button on metal or near metal studs.This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move the chime or doorbell button off the metal surface.

Don't mount the chime too close to ground level concrete slabs. This may also reduce the range. Mount the chime away from the floor.

Try different locations for the chime closer to the doorbell button. Also try to orient the chime at a different angle to increase the range.

The range of the doorbell depends on location, temperature and battery condition.

Technical Service

Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store.

If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.com. If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:

HeathCo LLC

P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service

* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.

- -

595-5494-11

FIVE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.

For a period of five years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. To obtain a refund or a replacement, return the product to the place of purchase.

Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, and expendable itemsare not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service.

This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HeathCo LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITEDTO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for all warranty requests.

HeathCo LLC reserves the right to discontinue and to change specifications at any time without notice without incurring any obligation to incorporate new features in previously sold products.

595-5494-11

- -

Loading...
+ 11 hidden pages