Heath Zenith SL-5505, SL-5503 User Manual

0 (0)

Model SL-5503 - 300 Watts

Model SL-5505 - 500 Watts

Quartz Halogen Floodlight

The Heath®/Zenith Quart Halogen Floodlight disperses light over a wide area. It includes a halogen lamp, attaches to a standard threaded junction box cover plate and is for use with 120 VAC.

FOR PROPER INSTALLATION AND OPERATION, PLEASE READ THESE INSTRUCTIONS CAREFULLY.

To Avoid Fire Or Burn Hazards:

• Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures.

Keep fixture at least 2” from combustible materials. Do not aim at objects closer than 3 feet.

Use a lamp that does not exceed the maximum ratings for your model. Maximum ratings are: SL-5503 - 300 Watts; SL-5505 - 500 Watts.

Fixture Installation Instructions

To avoid Electrical Shock:

WARNING: Turn power off at the circuit breaker or fuse.

Follow all warnings listed on fi xture.

Grounding and installations must comply with local codes and the National Electric Code.

This product should be mounted on a grounded junction box and must be used with a threaded cover plate.

Permanently mount the fi xture to a building or pole.

Fixture is designed for WALL MOUNT ONLY (see illustration below).

Thread aiming arm through the cover plate (not included) and tighten the locknut. Apply silicon caulk for a raintight seal.

Connect the lamp wires to the power source wiring. Secure with wire connectors.

Black to Black

 

Fixture ground to

junction box ground.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attach the cover plate to the junction box (Apply silicon caulk between cover plate and junction box for a raintight seal). Keep the fixture horizontal (within +/- 4°) so the bulb inside is horizontal. If the bulb is not horizontal, the bulb may darken or shatter and fail prematurely.

Loosen the side bolt connected to the arm to aim the fixture up and down.

Bulb Installation and Relamping

Important: Use a clean glove or cloth when handling the new bulb. Oil from your hand may cause the bulb to crack when the fi xture heats up and result in premature failure. Use isopropyl (rubbing) alcohol to clean the bulb if it is touched with your bare hands.

When relamping, turn power off and let the fixture cool.

Remove glass cover and remove the old bulb by pushing the bulb towards the right until the left side of the bulb is clear of the left socket.

To insert the new bulb push the bulb into the right socket so the bulb is properly seated in the sockets.

Re-install the glass cover.

Reconnect the power.

Cover Plate

White to White

WIRING FIXTURE

(Product May Vary from Illustration)

No Service Parts Available for this Product

598-1138-02

598-1138-02

© 2007 HeathCo LLC

Heath Zenith SL-5505, SL-5503 User Manual

Modelo SL-5503 - 300 Vatios

Modelo SL-5505 - 500 Vatios

Faro Halógeno de Cuarzo

El Faro Halógeno de Curzo Heath®/Zenith dispersa la luz a través de una área grande. Tiene una Lámpara de halógeno, se la coloca en una tapa roscanda estándar de caja de empalme y se la usa con 120 VCA.

Para su correcta instalacion y funcionamiento, por favor lea cuidadosamente estas instrucciones.

Para evitar pellgros de fuego o de quemazón:

Deje que el artefacto se enfríe antes de tocarlo. La bombilla y el artefacto funcionan a altas temperaturas.

Mantenga el artefacto por lo menos a 51 mm lejos de materiales combustibles. No lo apunte hacia objetos que estén más cerca de 1 m.

Use una lámpara que no exceda la potencia nominal máxima de su modelo.

Las potencias nominales máximas son: SL-5503 – 300 vatios; SL-5505 – 500 vatios.

Instrucciones para la instalación del artefacto

Para evitar el shock eléctrico:

ADVERTENCIA: Desconecte la energía en el cortacircuito.

Obedezca todas las precauciones listadas en este aparato.

La toma de tierra y la instalación deben cumplir con los códigos locales y con el Código Eléctrico Nacional.

Este producto debe ser montado sobre una caja de empalme conectada a tierra y se lo debe usar con una tapa roscada.

Monte permanentemente el artefacto en un deficio o en un poste.

El artefacto está diseñado para ser MONTADO SÓLO EN PARED (vea la ilustración de abajo).

Pase el brazo de apuntar por la tapa (que no se incluye) y ajuste la contratuerca. Aplique calafateo de silicona para obtener un sellado impermeable.

Conecte los alambres de la lámpara a los alambres de la fuente de energía. Asegúrelos con conectores de alambre.

Placa Cubertora

Negro a

Alambre a tierra de la

caja de empalme al cable

 

Negro

 

desnudo del aparato

 

 

Blanco a

Blanco

Fije la placa cubertora a la caja de empalme (Aplique calafateo de silicona entre la placa cubertora y la caja de empalme para obtener un sellado impermeable). Coloque la tapa en la caja de empalme. Mantenga el aparato horizontal (dentro de +/- 4°) de manera que la bombilla de adentro esté horizontal. Si la bombilla no está horizontal, se puede negrear o astillarse y dejará de funcionar prematuramente.

Afloje la tuerca lateral conectada al brazo para apuntar el aparato hacia arriba o hacia abajo.

Instalación de la bombilla y cambio de lámpara

Importante: Cuando vaya a colocar la nueva bombilla use un guante limpio, una tela o la espuma que viene con el producto. El aceite de su mano puede hacer que la bombilla se quiebre cuando se caliente y deje de trabajar prematuramente. Use alcohol etílico para limiar la bombilla si la ha tocado con sus manos desprotegidas.

Cuando cambie la lámpara, apague la energía y deje que el aparato se enfríe.

Quite la cubierta de vidrio y quite la bombilla vieja empujándola hacia la derecha hasta que la parte izquierda de la bombilla se haya salido del receptáculo izquierdo.

Para coloca la nueva bombilla, empújela hacia dentro del receptáculo derecho de manera que la bombilla quede correctamente asentada en los receptáculos.

Reinstale la cubierta de vidrio.

Reconecte la energía.

CABLEADO DEL APARATO

(El producto puede ser diferente al de la ilustración)

No hay piezas de servicio disponibles para este producto

© 2007 HeathCo LLC

598-1138-02

598-1138-02 S

Loading...
+ 2 hidden pages