Heath Zenith SH-5512 User Manual

4 (1)
Heath Zenith SH-5512 User Manual

DualBrite® Twin Halogen

Motion Sensing Light

Model SH-5512

Meets the ENERGY STAR® guidelines when DualBrite® function is off and ON-TIME is 1 or 5 minutes and when used with 120 W Max bulbs.

Features

DualZone™ Technology.

Turns on lighting when motion is detected.

Automatically turns lighting off.

Bulb Saver™ - Extends bulb life by up to 4x standard bulbs. Lights bulb to full bright in under 2 seconds.

DualBrite® Timer.

Photocell keeps the lighting off during daylight hours.

LED indicates motion was sensed (day or night).

Package Contents

Rubber Plug

Plastic Hanger

6 Mounting Cover Screws (3 sizes)

Plate

3 Wire

Connectors

Sensor

Light Control

Mounting Bolt

Mounting Strap

Gasket

 

 

 

Requirements

The light control requires 120-volts AC.

If you want to use Manual Mode, the control must be wired through a switch.

Some codes require installation by a qualified electrician.

This product is intended for use with the enclosed gasket and with a junction box marked for use in wet locations.

OPERATION

Mode:

On-Time

Works: Day

Night

Test

5 Seconds

x

x

Auto

1, 5, or 20 Min

 

x

Manual

To Dawn*

 

x

Accent

3, 6 Hr, to Dawn

 

x

* resets to Auto Mode at dawn.

Note: When first turned on wait about 1 1/2 minutes for the circuitry to calibrate.

TEST

Put ON-TIME switch

ON-TIME

DualBrite®

on the sensor bottom

 

 

 

 

 

 

 

 

 

 

toTEST and the Dual-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEST 1 5 20

Off 3 6 Dusk to

Brite® switch OFF.

 

 

 

 

 

 

 

 

 

Dawn

 

AUTO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Put the ON-TIME switch in the 1, 5,

 

 

ON-TIME

or 20 minute position.

TEST 1 5 20

MANUAL MODE

Manual mode only works at night because daylight returns the sensor to AUTO.

Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE.

Manual mode works only with the ON-TIME switch in the 1, 5, or 20 position.

1 Second OFF

then...

... back on.

2 Halogen Bulbs

Light Shield

© 2008 HeathCo LLC

598-1160-03

Mode Switching Summary

TEST Move ON-TIME Switch to

1, 5, or 20 minutes

AUTO

Flip light switch off for one second

then back on*

MANUAL MODE

*If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control will be in the AUTO mode.

DualBrite® Timer

Light comes on half bright for selected time after dusk (Off, 3 hr., 6 hr., until dawn). Selecting OFF disables this feature. The motion sensing features will continue to work as described in this manual.If motion is sensed, the light turns on full bright for the ON-TIME (1, 5, or 20 minutes) then returns to dim mode.

INSTALLATION

CAUTION: Keep the sensor at least 1" (25 mm) away from the bulbs.

CAUTION: To Avoid Fire Or Burn Hazards:

Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures.

Keep fixture at least 1" (25 mm) from combustible materials. Do not aim at objects closer than 3 ft. (1 m).

Use only T3, 150W (max.) tungsten halogen 120 VAC bulbs.

For easy installation, select an existing light operated by a wall switch for replacement.

For best performance, mount the fixture about 8 ft. (2.4 m) above the ground. NOTE: If fixture is mounted higherthan8ft.(2.4m),aimingthesensordownwillreduce coverage distance.

For under eave installation, the sensor head must be rotatedasshowninthenexttwostepsforproperoperation and to avoid the risk of electrical shock. Also for proper under eave operation, remove the protective backing from the light shield and stick on as shown below.

For eave mount only:

Swing the sensor head towards the clamp screw joint.

Controls

Clamp Screw

Then rotate the sensor head clockwise 180° so the controls face down.

Controls

Light Shield

Opening

Controls

If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done.

Bulb Installation and Replacement

NOTE: Bulbs are included, but you will need to install them

NOTE: When replacing bulbs, turn power off and let the fixture cool.

Open glass covers.To remove the old bulb push the bulb towards the right (with fixture as shown) until the left side of the bulb is clear of the left socket.

To install a bulb, push the bulb into the right socket so the bulb fits completely into the left socket.

Check that the bulb is seated properly.

Close the glass covers.

598-1160-03

Wire the Light Control

WARNING: Turn power off at circuit breaker or fuse.

Remove the existing light fixture.

Install mounting strap to junction box using screws appropriate for your junction box.

The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap.

Thread all fixture wires through the large holes in the gasket as shown.

Connect the junction box wires to the light fixture wires as shown. Twist together and secure with wire connectors.

Mounting

 

 

 

White to

Black to

Strap

White

Black

Rubber

Plug

Mounting

Bolt

Gasket

Connect any fixture ground wire(s) and the cover plate ground screw to the junction box ground wire.

Mount the Light Control

Place the mounting bolt through the front of the junction box cover. Push the small gasket hole over the mounting screw.

Make sure the wire connectors and wires are inside the junction box. Align the mounting screw with the center hole in the mounting strap.Secure the fixture to the mounting strap.

Push the rubber plug over the mounting screw.

Keep bulbs at least 1" (25 mm) from the sensor.

Push the rubber plug firmly into place.

If not installed on a weatherproof box, caulk the wall plate and mounting surface with silicone

Adjust the bulb holders by loosening the lock nuts but do not rotate the bulb holders more than 180° from the factory setting.

598-1160-03

Clamp
Screw
Ball
Joint
Aim Sensor Down for Short Coverage
Aim Sensor Higher for Long Coverage

TEST AND ADJUSTMENT

Turn on the circuit breaker and light switch.

NOTE: Sensor has a 1 1/2 minute warm up period before it will detect motion. When first turned on, wait 1 1/2 minutes.

NOTE: Meets the ENERGY STAR® guidelines when DualBrite® function is off and ON-TIME is 1 or 5 minutes and when used with 120 W Max bulbs.

Turn the RANGE control to the medium position (halfway between MIN and MAX), DualBrite® to OFF, and the ON-TIME control to the TEST position.

MAX

 

ON-TIME

DUAL BRITE™

 

O

 

B

 

 

 

O

 

 

 

S

 

 

 

T

 

 

MIN

TEST 1 5 20

OFF 3 6 DUSK TO

RANGE

 

MINUTES

HOUR DAWN

Bottom of Sensor

Avoid aiming the control at:

Objects that change temperature rapidly, such as heating vents and air conditioners. These heat sources could cause false triggering.

Areas where pets or traffic may trigger the control.

Nearby large, light-colored objects reflecting light may trigger the shut-off feature. Do not point other lights at the sensor.

240°

8 ft.

 

 

(2.4 m)

DualZone

 

DualZone

70 ft. 100 ft.

 

(21 m) (30.5 m)

 

 

Boosted

Maximum

 

 

Maximum Range

Coverage Angle

NOTE: If fixture is mounted higher than 8 ft.(2.4 m), aiming the sensor down will reduce coverage distance.

The detector is less sensitive to motion directly towards it.

 

 

 

 

 

 

 

 

Motion

 

 

 

Motion

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DualZone

Sensor

DualZone

 

 

Least Sensitive

 

Most Sensitive

Loosen the clamp screw in the sensor ball joint and gently rotate the sensor.

Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times whenmotionisdetected).Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (25 mm) away from the bulbs.

Adjust the RANGE as needed. RANGE set too high may

increase false triggering.

Secure the sensor head by tightening the clamp screw.

Do not overtighten the screw.

Set the amount of TIME you want the lights to stay on after motion is detected (1, 5, or 20 minutes).

Set the DualBrite® switch to the amount of time after dusk you want the lights on at low level (Off, 3, 6 Hrs., Dusk-to-Dawn).

WARNING - Risk of fire. Do not aim the bulbs at a combustible surface within 3 ft. (1 m).

NOTE: DualZone™ is a new zone of detection which was added as an option to select Heath®/Zenith motion sensing products. This feature adds a zone of detection under the motion sensor. DualZone™ requires no additional adjustment and operates in conjuction with the forward-looking sensor.

598-1160-03

SPECIFICATIONS

Horizontal Range. .

. Up to 70 ft. (21 m); 100 ft.

 

(30.5 m) with Range Boost.

 

[varies with surrounding

 

temperature]

Vertical Range. . .

. Up to 15 ft. (4.6 m)

Sensing Angle. . .

. Up to 240° horizontal. Up to 80°

 

Vertical

Electrical Load. . .

. Up to 300 Watt Maximum Tung-

 

sten Halogen [Up to 150 Watt

 

Maximum each bulb holder.]

Power Requirements. 120 VAC, 60 Hz

Operating Modes. .

. TEST, AUTO, and MANUAL

 

MODE

Time Delay . . . .

. 1, 5, 20 minutes

Replacement bulb. .

T3, 150W halogen maximum

 

120 VAC

DualBrite® Timer. .

. Off, 3, 6 hours, Dusk-to-Dawn

HeathCo LLC reserves the right to discontinue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold.

TROUBLESHOOTING GUIDE

SYMPTOM

POSSIBLE CAUSE

 

 

Lights will

1. Light switch is turned off.

not come on.

2.

Light is loose or burned out.

 

3.

Fuse is blown or circuit breaker is

 

 

turned off.

 

4.

Daylight turn-off is in effect (Recheck

 

 

after dark).

 

5.

Incorrect circuit wiring, if this is a new

 

 

installation.

 

6.

Re-aim the sensor to cover desired

 

 

area.

Lights come

1.

Light control may be installed in a

on in day-

 

relatively dark location.

light.

2.

Light control is in TEST. (Set control

 

 

 

switch to an ON-TIME position).

 

 

Lights come

1. Light control may be sensing small

on for no

 

animals or automobile traffic. (Re-aim

apparent

 

sensor).

reason.

2. RANGE is set too high. (Reduce

 

 

RANGE).

 

3.

DualBrite® Timer is on.

Lights turn

1. Sensor is in a relatively dark location.

off too late

 

(Relocate sensor, or use 3 hr or 6 hr

in Dusk-to-

 

setting).

Dawn setting.

 

 

 

 

 

SYMPTOM

POSSIBLE CAUSE

 

 

Lights stay

1. A bulb is positioned too close to the

on continu-

 

sensor or pointed at nearby objects

ously.

 

that cause heat to trigger the sensor.

 

 

(Reposition the bulb away from the

 

 

sensor or nearby objects).

 

2.

Sensor is pointed toward a heat source

 

 

like an air vent, dryer vent, or brightly-

 

 

painted heat-reflective surface.(Repo-

 

 

sition sensor. Reduce RANGE).

 

3.

Light control is in Manual Mode.(Switch

 

 

to Auto).

 

 

 

Lights flash

1.

Heat or light from the bulbs may be

on and off.

 

turning the light control on and off.

 

 

 

 

(Reposition the bulbs away from the

 

 

sensor).

 

2.

Heat being reflected from other objects

 

 

may be affecting the sensor. (Reposi-

 

 

tion sensor).

 

3.

Light control is in the TEST mode and

 

 

warming up.(Flashing is normal under

 

 

these conditions. Turn BOOST off).

 

 

 

Lights flash

1.

Sensor is detecting its own lights.

once, then

 

(Reposition bulbs to keep area below

stay off in

 

the sensor relatively dark).

Manual Mode.

 

 

 

 

 

598-1160-03

Technical Service

Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store.

If you experience a problem, follow this guide.You may also want to visit our Web site at: www.hzsupport.com. If the problem persists, call* for assistance at 1-800-858-8501 (English speaking only), 7:30 AM to 4:30 PM CST (M-F). You may also write* to:

HeathCo LLC

P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service

* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

TEN YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.

For a period of ten years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HeathCo LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for all warranty requests.

598-1160-03

Loading...
+ 14 hidden pages