SB-16-230
harman/kardon Service Manual
SB 16/230
Active Sou ndbar with wireless subwoofer
Released EU2011 Harman Consumer Group, Inc. Rev 0, 06/2011
8500 Balboa Boulevard
Northridge, California 91329
CONTENTS
ESD WARNING 2
PACKAGE GUIDE AND PARTS, CENTER 3
PACKAGE GUIDE AND PARTS, SUB 4
EXPLODED VIEW AND PARTS, CENTER 5
EXPLODED VIEW AND PARTS, SUB 6
PARTS LIST, SUB 7
SCHEMATIC DIAGRAMS 8
ASSEMBLY AND DISASSEMBLY, CENTER 12
OWNER’S MANUAL 16-29
Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
CAUTION :
harman/kardon
SB 16/230 Service Manual
Page 2 of 29
harman/kardon
SB 16/230 Service Manual
Page 3 of 29
harman/kardon
SB 16/230 Service Manual
Page 4 of 29
harman/kardon
SB 16/230 Service Manual
Page 5 of 29
1
2
3
4
5
6
7
8
序號 品名 料號
1
Screw for
amplifier
10
數量
2
Amplifier
1
4
3
Logo
Wood
Cabinet
1
1
Rubber
Foot
8 4
6
7
5
Screw for
woofer
Woofer
1
5
1
Logo fot
grille
241-100-00613-2BCE
010-7610-05246-E
25PF12DZB-FW01-E
352-AM04020D210-E
316-AL-00553-E
316-AG-00557-E
352-FM04020D605-E
320-RUB-00057-0BAE
作 業 指 示
版本日期
2009/12/03
0
頁次
1
客 戶:
機 種:
初版發行
0
ISSUE REVISIONS
表單編號: 版
確認
承認
DATE NAME
制作
蔣國正
2009/12/03
務
注:
1.銘板(316-AL-00553-E)背後點3188膠水
再貼到鐵網卞槽中
2.銘板(316-AL-00553-E)的位置是:銘板下端距
靠LED燈的箱體邊緣60mm,左右居中
1
2
3
harman/kardon
SB 16/230 Service Manual
Page 6 of 29
Harman/Kardon SB 16/230 subwoofer, Exploded View
Harman/Kardon SB15 wireless subwoofer. System Parts list.
The sub is used in the SB 16/230 soundbar system.
SB15 Sub
Part Number Part Description
352-AM04020D210-E
Screw for Subwoofer
010-7610-05246-E
Amplifier SB15/230 SUB
241-100-00613-2BCE
Wood Cabinet
316-AG-00557-E
Harman Kardon Logo for the Sub top board
316-AL-00553-E
Logo for grille
25PF12DZB-FW01-E
10" Subwoofer
352-FM04020D605-E
Screw for woofer to wood cabinet
320-RUB-00057-0BAE
Rubber pad for subwoofer cabinet
051-A05264D-E POWER AMP PCB ASSY SB15 SUB
051-A05264C-E PCB WIRELESS BCB ASSY SB15 SUB
051-A05264B-E PRE AMP PCB ASSY SB15 SUB
051-A05264A-E STANDBY PCB ASSY SB15 SUB
302-FE-05275-0BAE Subwoofer Amplifier panel
150-E0764201-E Transformer
152-V60202603-E Power Cord
154-V09006T0-E Fuse
155-520020-E Fuse holder
162-50652003-E Speaker Wire
180-P3024DB-E Power Rock Switch
306-ABS-05082-0BAE Rear Enclosure
323-AL-05184-0LAE Aluminum heat sink
335-NYL-00002-0BAE Power Cord Strain Relief
311-ABS-00028-0BAE Knob
harman/kardon
SB 16/230 Service Manual
Page 7 of 29
1
1
2
2
3
3
4
4
D D
C C
B B
A A
VSS
VCC
SGND
VSS
VCC
SGND
SGND
22K
R01
22K
R08
220P
C02
18.7k
R06
15.4k
R04
17.8k
R02
33n
C04
24.9K
R05
100p
C03
220k
R09
VCC
10k
R07
VSS
220p
C05
1
2
3
4
5
6
sw1
SW2-2
10K
R03
10K
R10
mout
84
7
5
6
2
U2B
TL072CN
100n
C06
VCC
VSS
10u
C01
8.25k
R21
+12VC
100u
C11
IN
3
2
OUT
1
GND
U5
MC78L12CP
VCC
3.3k
R18
VCC
VSS
VCC
VSS
100u
C21
4.7u
C23
SGND
SGND
SGND
SGND
VCC
VSSSGND
220p
C29
4.7u
C34
100n
C35
100n
C25
4.7u
C36
4.7u
C26
100u
C32
4.7u
C37
4.7u
C28
100n
C13
100n
C12
220n
C38
100n
C08
22n
C27
47k
R23
24.9k
R19
22k
R22
14.3k
R20
VCC
VSS
SGND
100n
C15
82.5k
R15
12.1K
R11
OUT
Netsw1_3
6.8k
R17
10u
C16
220n
C18
10u
C17
V+
1
OUTa
2
INa
3
INT
4
Vref
5
SENCE
6
SW
7
INb
8
OUTb
9
GND
10
U4
NJM2761-10
4.7u
C22
VR2A
VR*2
VR2B
VR*2
A50k
VR1
1
2
3
4
5
CON2
Header 5
SGND
OUT
8
1
4
3
2
1
U2A
TL072CN
8
1
4
3
2
1
U3A
TL072CN
84
7
5
6
2
U3B
TL072CN
mout
100n
C09
VCC
VSS
SGND
100n
C30
82.5k
R16
12.1K
R12
2
3
1
A
411
U1A
TL074CD
SGND
VCC
VSS
5
6
7
B
411
U1B
TL074CD
10
9
8
C
411
U1C
TL074CD
12
13
14
D
411
U1D
TL074CD
1
2
3
4
5
CON1
Header 5
VSS
VCC
SGND
CUSTOMER:JBL
MODEL:SB 15SUB/230
DETA:SEP.01.2009
PREPAREDCHECKEDCHECKEDAPPROVED REV
1.0
PAGE 2/5
BOARD: PERAMP
harman/kardon
SB 16/230 Service Manual
Page 8 of 29
1
1
2
2
3
3
4
4
D D
C C
B B
A A
S/L
1
CLK INH
15
CLK
2
SI
10
A
11
B
12
C
13
D
14
E
3
F
4
G
5
H
6
QH
9
QH
7
VCC
16
GND
8
U04
SN74HC165D
S/L
1
CLK INH
15
CLK
2
SI
10
A
11
B
12
C
13
D
14
E
3
F
4
G
5
H
6
QH
9
QH
7
VCC
16
GND
8
U03
SN74HC165D
20K
R08
20K
R10
20K
R12
20K
R17
20K
R19
20K
R21
20K
R23
20KR07
20KR09
20KR11
20KR14
20KR16
20KR18
20KR20
20KR22
10K
R24
GND GND
GND
GND
10K
R15
GND
100R
R13
1000u/10V
C02
100n
C03
10n
C04
1000u/10V
C07
100n
C05
10n
C06
100n
C15
100n
C16
VCC
VCC
GND GND
4.7R
R04
4.7R
R01
GND
SCK
23
AGND2
24
LRCK
19
PI2
20
PC5
15
MCLK
16
MSIO0
7
MOSI0
8
SCK0
9
Vcc
4
/RST
5
RFVcc
1
AGND1
21
SDOUT
22
AVdd
25
PB1(CS0)
6
RFGND
2
GND
3
PF1(ID_CLK)
11
PC0(ID_LATCH)
12
/PC1(MUTE_LED)
13
PF0(ID_DATA)
10
/PC4(BOND_LED)
14
PC7(I2C_SDA)
17
PI0(I2C_SCL)
18
RX M1087
MD1
Rx M1087
/RST
1
SDATA
2
SCLK/DEM1
3
LRCK
4
MCLK
5
DIF1
6
DIF0
7
DEM0
8
FILT+
9
VQ
10
REF_GND
11
AOUTR
12
AGND
13
AV
14
AOUTL
15
MUTEC
16
U06
CS4340
AGND
4.7K
R33
100n
C32
100n
C29
100n
C21
1000u/10V
C20
10k
R42
10k
R43
10k
R28
10k
R40
1n
C23
1n
C31
AGND
8
1
4
3
2
U05A
NJM4560
3.9k
R35
20k
R27
150p
C19
3.9k
R41
20k
R39
150p
C27
84
7
5
6
U05B
NJM4560
AGND
AGND
AGND
AGND
GND
470u/16V
C13
100n
C14
VCC
VCC
VCC
VCC
AGND
33R
R36
VCC
33R
R25
470u/16V
C18
100n
C17
AGND
VCC1
VCC1
GND
AGND
1
2
3
4
5
SW1
SEL
GND
1
2
3
4
5
6
7
8
CON1
Header 8
100n
C01
GND
47k
R03
VCC
GND
100R
R29
100R
R30
100R
R31
100R
R32
AGND
link1
GND
1 2
BD2
BD
12
BD1
BD
D01
SCD14
100R
R44
100R
R45
nRESET
2
Vss
1
Vcc
3
U02
STM809
510
R47
Q02
8050S
Q03
8050S
Q01
8050S
510
R48
20k
R49
47k
R50
47k
R51
1
2
3
CON2
Header 3
link1
link1
VCC
1
2
CON4
Header 2
47k
R52
Q04
8550S
0.22u
C22
10u
C30
10u
C28
10u
C25
10u
C26
33R
R37
470u/16V
C33
100n
C24
1
2
3
4
5
CON3
Header 5
AGND AGND
VSS
VSS
VSS
open
C34
open
C35
open
C36
open
C37
open
C38
open
C39
GND
open
C40
open
C41
GND
GNDGND
CUSTOMER:JBL
MODEL:SB 15SUB/230
DETA:SEP.01.2009
PREPAREDCHECKEDCHECKEDAPPROVED REV
1.0
PAGE 3/5
BOARD: WIRLESS
GND
rest
rest
harman/kardon
SB 16/230 Service Manual
Page 9 of 29
Loading...