HK 3380 Stereo Receiver
OWNER’S MANUAL
SPEAKER 1 |
MUTE AUTO TUNED STEREO RDS PTY CT RT TA MEMORY PRESET |
SPEAKER 2 |
SLEEP |
|
PHONO |
VID 1 |
FM |
VID 2 |
AM |
VID 3 |
CD |
TAPE M. |
Power for the Digital Revolution®
Table of Contents
3 Introduction
3Important Information
4Front Panel Controls
6 Rear Panel Connections
8 Remote Control Functions
10 Installation and Connections
12 Operation
12 Basic Operation
12 Source Selection
12 Tuner Operation
13 RDS Operation
14 Tape Recording
14 Memory Backup
14Processor Reset
15Using the Remote Control
16Troubleshooting Guide
17Technical Specifications
Declaration of Conformity
We, Harman Consumer International
2, Route de Tours
72500 Château-du-Loir,
FRANCE
declare in own responsibility, that the product described in this owner’s manual is in compliance with technical standards:
EN 55013/6.1990
EN 55020/12.1994
EN 60065:1993
EN 61000-3-2/4.1995
Carsten Olesen
Harman Kardon Europe A/S
10/03
Typographical Conventions
In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used.
EXAMPLE – (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack
EXAMPLE – (OCR type) indicates a message that is visible on the front-panel information display
1– (number in a square) indicates a specific front panel control
å– (letter in a circle) indicates a button or indicator on the remote
– (number in a circle) indicates a rear panel connection
2 TABLE OF CONTENTS
Introduction
Congratulations! With the purchase of the Harman Kardon HK 3380 you are about to begin many years of listening enjoyment.
While sophisticated systems are hard at work within the HK 3380 to make all of this happen, hookup and operation are simple. Color-keyed connections and a comprehensive remote control make the HK 3380 easy to use.
To obtain maximum enjoyment from your new receiver, we urge you to take a few minutes to read through this manual. This will ensure that connections to speakers, source playback units and other external devices are made properly. In addition, a few minutes spent learning the functions of the various controls will enable you to take advantage of all the power the HK 3380 is able to deliver.
If you have any questions about this product, its installation or operation, please contact your dealer. He is your best local source of information.
Description and Features
Harman Kardon’s HK 3380 is a full-featured Stereo receiver, with five inputs and an FM stereo/FM/AM tuner with RDS capabilities that provide for the utmost flexibility. A high-quality phono input is available so that you may continue to enjoy your existing record collection as well as the latest CD recordings.
The HK 3380’s powerful amplifier uses traditional Harman Kardon High-Current Design philosophies to meet the wide dynamic range of any program selection.
Harman Kardon invented the high-fidelity receiver more than fifty years ago. With state-of-the- art features and time-honored circuit designs, the HK 3380 is one of the finest receivers ever offered by Harman Kardon.
■Harman Kardon Designed High-Current, Ultrawide Bandwidth Amplifier
■Four video inputs and a recording output
■Front-panel audio/video inputs
■Phono Input Section
■Speaker 1/Speaker 2 Outputs for HighQuality Sound in Two Locations
■Pre-Out/Main-In jacks for use with External Amplifiers, Equalizers or Speaker Processors
■System Remote Contol with Numeric Keys
■Subwoofer Output
■Tuner with RDS Data Program Information Displays
Important Information
Verify Line Voltage Before Use
Your HK 3380 has been designed for use with 220-240-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard, and may damage the unit.
If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service station.
Installation Location
■To assure proper operation, and to avoid the potential for safety hazards, place the unit on a firm and level surface, that can support the weight of the product.
■Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances a fan may be required.
■Do not place the unit directly on a carpeted surface.
■Avoid installation in extremely hot or cold locations, or an area that is exposed to direct sunlight or heating equipment.
■Avoid moist or humid locations.
■Do not obstruct the ventilation slots on the top of the unit, or place objects directly over them.
Cleaning
When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet.
Unpacking
The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move, or should the unit ever need repair.
If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environment and discard those materials at a local recycling center.
INTRODUCTION 3
Front Panel Controls
27 |
|
26 |
|
25 |
|
28 |
|
23 |
SPEAKER 1 |
MUTE AUTO TUNED STEREO RDS PTY CT RT TA MEMORY PRESET |
SPEAKER 2 |
SLEEP |
|
PHONO |
VID 1 |
FM |
VID 2 |
AM |
VID 3 |
CD |
TAPE M. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
5 |
|
8 |
|
|
9 |
|
|
|
@ |
|
24 |
|
|
^ |
|
( |
|
|||||||||
|
|
|
|
|
|
|
|
# |
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
4 |
6 |
7 |
) ! $ % |
|
& * |
|
22 |
|
21 |
20 |
1 |
1Video 3 input jacks 2 System Power Control 3 Power Indicator
4 Headphone Jack
5 Mute
6 Speaker 1 Selector
7 Speaker 2 Selector
8 Phone Input Selector
9 T-Mon Input Selector ) Tuning Button
1Video 3 Input Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players.
To select the front-panel inputs, press the Video 3 Input Selector Úrepeatedly until the dot to the left of the Video 3 Input Indicator ˆ flashes. In order to view the video signal of a video device connected to this input, remember to connect the Video Monitor Output to the video input of your TV or video display.
! Video 1 Input Selector
@ Preset Scan
# CD Input Selector
$ Video 2 Input Selector
% Preset Selector
^ Dimmer
& FM/AM Selector
* FM Mode Selector
( Sleep Button
Ó Bass Control
2System Power Control: Press this button to turn on the HK 3380; press it again to turn the unit off (to Standby). Note that the Power Indicator surrounding the switch 3will turn blue when the unit is on.
3Power Indicator: This LED will illuminate in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on. When the unit is in operation, the indicator will turn blue. A red indicator means that the unit is in the Protect mode, and should be turned off and then checked for a possible speaker wire short circuit.
Ô Treble Control
Balance Control
Ò Volume Control
Ú Video 3 Input Selector
Û Information Display
Ù Speaker Selection Indicators
ı Remote Sensor Window
ˆ Input Indicators
4Headphone Jack: This jack may be used to listen to the HK 3380’s output through a pair of headphones. Be certain that the headphones have a standard 6,3 mm stereo phone plug.
5Mute: Press this button to momentarily silence the speaker and preamp output of the HK 3380.
6Speakers 1 Selector: Press this button to turn the speakers connected to the Speaker 1 output terminals on or off.
7Speakers 2 Selector: Press this button to turn the speakers connected to the Speaker 2 output terminals on or off.
4 FRONT PANEL CONTROLS
Front Panel Controls
8Phono Input Selector: Press this button to select the output of a turntable that is connected to the Phono inputs .
9T-Mon Input Selector: Press this button to listen to the output of a tape recorder connected to the Tape Monitor inputs . The TAPE M. will be highlighted in the Input Indicators ˆ to indicate that the input source is being monitored when the HK 3380 is connected to a three-head tape deck or another unit with offhead playback.
)Tuning Button: Press the left side of the button to tune lower frequency stations and the right side of the button to tune higher frequency stations. When a station with a strong signal is tuned, the TUNED indicator will illuminate in the
Information Display Û. A brief press of the button will manually tune to the next frequency increment, while pressing and holding the button for a longer period (>0.5 sec) will step quickly through the frequencies. As soon as the button is released the unit will automatically tune to the next station with a signal strong enough for acceptable reception.
!Video 1 Input Selector: Press this button to listen to and/or view the output of a device connected to the Video 1 Inputs .
@ Preset Scan: Press this button to automatically scan through the stations that have been programmed in the HK 3380’s memory. The tuner will play five seconds of each station before moving to the next preset station. To stop the scan when the desired station is heard, press the button again. (See page 13 for more information on the tuner memory system.)
#CD Input Selector: Press this button to listen to the output of a CD player connected to the CD inputs .
$Video 2 Input Selector: Press this button to listen to and/or view the output of a device connected to the Video 2 Inputs .
%Preset Selector: Press this button to step up or down through the list of stations that has been entered into the preset memory. (See page 13 for more information on tuner programming.)
^Dimmer: Press this button to dim the front panel displays and indicators. The first press of the button will dim the displays to one-half normal brightness; the next press will turn all displays off except for the Power Indicator 3. The display will return to normal brightness the next time the unit is turned on.
&FM/AM Selector: Press this button to select the tuner as the input to the receiver. When the tuner is in use, press this button to change between the AM and FM frequency bands.
Note: When an RDS station is tuned, the FM button has the same function as the RDS Display button on the remote control. Press to cycle through the various RDS displays (see page 13).
*FM Mode Selector: Press this button to select the stereo or mono mode for FM tuning. In the STEREO mode, a Stereo Indicator will illuminate in the Information Display Û, and stereo reception will be provided when stations are transmitting stereo signals. In the MONO mode, the left and right signals from stereo broadcasts will be mixed together and reproduced through all channels. Select MONO for better reception of weak signals.
(Sleep Button: Press this button to place the unit in the Sleep mode. Each press of the button selects the amount of time that will remain before the unit automatically goes into the Standby mode, as shown in the Information Display Û, in the following order:
|
|
|
90 |
|
|
80 |
|
|
|
70 |
|
|
60 |
|
50 |
|
|||
|
|
|
min |
|
|
|
min |
|
|
min |
|
|
|
min |
|
|
min |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
40 |
|
|
|
30 |
|
|
20 |
|
|
|
10 |
|
|
OFF |
|||
|
|
|
min |
|
|
|
min |
|
|
min |
|
|
|
min |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ÓBass Control: Turn this control to modify the low-frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste and room acoustics.
ÔTreble Control: Turn this control to modify the high-frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste and room acoustics.
Balance Control: Turn this control to change the relative volume for the front left/right channels.
ÒVolume Control: Turn the knob clockwise to increase volume, counterclockwise to decrease the volume.
ÚVideo 3 Input Selector: Press this button to listen to and/or view the output of a device connected to the Video 3 Inputs 1on either the front or rear panel. If devices are connected to both the frontand rear-panel Video 3 Inputs 1, then the device connected to the rear-panel Video 3 Inputs will be selected first, as indicated by the dot to the left of the Video 3 Input Indicator ˆbeing steadily lit. To select the device connected to the front-panel Video 3 Inputs 1, press the Video 3 Input Selector Úagain so that the dot to the left of the Video 3 Input Indicator ˆ flashes. Each subsequent press of the Video 3 Input Selector Úwill toggle between the front and rear Video 3 Inputs 1.
ÛInformation Display: This display delivers messages and status indications to help you operate the receiver.
ÙSpeaker Selection Indicators: These indicators light as a green LED next to the designation for each speaker pair to show when they are active. Press the Speaker 1 6or
Speaker 2 7Selectors to activate either pair of speakers.
Both sets of speakers may be selected simultaneously as long as all speakers are norminally rated at an impedance of 8 ohms or greater. However, occasionally the actual impedance will vary, depending upon the program material. When the impedance drops too low, the HK 3380 will go into protect mode in order to prevent damage to the equipment. If this should occur frequently, be sure to select only one set of speakers at a time until you are able to obtain speakers with a higher nominal impedance.
ıRemote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.
ˆInput indicators: A blue LED will light in front of the input that is currently being used as the source for the AVR.
FRONT PANEL CONTROLS 5
Rear Panel Connections |
|
|
|
|||
|
¡ |
™ |
|
b ¢∞ |
a |
|
|
§ |
ª |
• |
¤ fi |
fl |
° |
£ |
¶ |
‚ |
⁄ |
‹ |
‡ |
· |
AM Antenna |
|
|
Tape Monitor Play/In |
Speaker 1 Terminals |
||
FM Antenna |
|
|
Tape Monitor Record/Out |
Speaker 2 Terminals |
||
Phono Ground |
|
|
Video 1 Audio/Video Record/Out |
Switched AC Outlets |
||
Remote IR In |
|
|
Video 2 Audio/Video Inputs |
Power Cable |
||
Remote IR Out |
|
|
Main In |
Video Monitor Outputs |
||
Phono Inputs |
|
|
Video 3 Audio/Video Inputs |
|
||
CD Inputs |
|
|
Preamp Out |
|
||
Video 1 Audio/Video Play/In |
|
Subwoofer Out |
|
|||
6 REAR PANEL CONNECTIONS |
|
|
|
|