Dryers
Sécheuses
Secadoras
Owner's Manual & Installation Instructions
Manuel d'utilisation et Instruction d'installation
Manual del propietario y Instrucciones de instalación
QFD15 Series/Séries/Serie
49-3000195 06-19 GEA
ENGLISH
TABLE OF CONTENTS
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
USING THE DRYER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Stacking (Optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Reversing The Door Swing (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TROUBLESHOOTING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 CONSUMER SUPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
RECORD KEEPING
Thank you for purchasing this Haier Appliances product. This Owner's Manual will help you get the best performance from your new dryer.
For future reference, record the model and serial number located on a label on the front of the dryer behind the door.
Staple your proof of purchase to this manual to aid in obtaining warranty service if needed.
____________________________________________________
Model number
____________________________________________________
Serial number
____________________________________________________
Date of purchase
2 |
49-3000195 |
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
|
To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance, |
|
WARNING |
||
follow basic precautions, including the following: |
ʄRead all instructions before using the appliance.
ʄDO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
ʄDO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of the tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
ʄDO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this appliance is used near children.
ʄBefore the appliance is removed from service or discarded, remove the door to the drying compartment.
ʄDO NOT reach into the appliance if the drum is moving.
ʄDO NOT install or store this appliance where it will be exposed to the weather.
ʄDO NOT tamper with controls.
ʄDO NOT climb or stand on this unit.
ʄDO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.
ʄFollow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.
ʄDO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
ʄDO NOT dry articles containing foam rubber or similarly textured rubber-like materials.
ʄClean lint screen before or after each load.
ʄDO NOT operate the dryer without the lint filter in place.
ʄDO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust and dirt.
ʄThe interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.
ʄUnplug the appliance or turn off the circuit breaker before servicing. Pressing the Power () or Start/Pause ( ) button DOES NOT disconnect power.
ʄDO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
ʄDO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner when cleaning dryer interior. Hazardous fumes or electrical shock could occur.
ʄSee “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.
ENGLISH
READ AND SAVE THESE INSTRUCTIONS
49-3000195 |
3 |
ENGLISH
USING THE DRYER
|
|
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY |
||
|
WARNING |
|||
|
INFORMATION before operating this appliance. |
|
||
|
|
|
|
|
Throughout this manual, features and appearance may vary from your model. |
Step 4* |
|||
Step 1* |
Step 2* |
Step 3* |
• If the screen is dark, press and hold the power button for 2 seconds to “wake up” the display.
•Loosely add items.
•Close door.
NOTE: Dryer will not start with door open.
•Select a dry cycle. (Defaults are set for each dry cycle. These default settings can be changed. See control settings for more information.)
•Press and hold the start button for 1 second.
*Instructions can also be found by touching the document () icon, on the cycle selection screen, in the top right corner.
Controls
I
C O N D E N S E R D R Y E R
|
|
B |
J |
A |
|
|
|
|
|
|
|
|
|
H |
|
|
|
|
G |
C |
D |
E |
|
F |
4 |
49-3000195 |
USING THE DRYER
Display and Status Lights
The display shows the approximate time remaining until the end of the cycle.
In addition, this display will show the dryer status:
Status |
Dry |
Damp |
Cool |
|
Controls lock feature. |
||
Clean Filter |
Time to clean the filter. See the Care and Cleaning section. |
||
Damp Alert |
When Damp Alert option is selected and clothes have dried to a damp dryness level, indicator will appear and dryer will beep. |
||
Estimated Time |
Display shows the estimated time remaining until set cycle is completed. |
||
Remaining |
|||
Ext Tumble |
Indicates the Extended Tumble feature is set. |
||
Delay |
Indicates Delay Dry set time is selected. |
||
Low Air |
Indicates decrease in performance of the dryer and increase risk of lint accumulation in the ducts and dryer. |
||
|
Indicates the My Cycle feature is set. |
||
eDry |
Shows eDry setting selected. |
||
Temp |
Shows High, Medium, Low or No Heat temperature setting selected. |
||
Level |
Shows Extra Dry, Dry or Damp dryness setting selected. |
||
Delay Dry |
Indicates Delay Dry is set time is selected. |
||
|
|
|
|
|
|
Power |
|
|
|
|
A |
|
|
||
|
Press and hold for 2 seconds to “wake up” the display. If the display is active, press and hold for 2 seconds to turn the |
||||
|
|
||||
|
|
dryer off. NOTE: Pressing the power does not disconnect the appliance from the power supply. |
|||
|
|
|
|
|
|
|
|
Dry Cycles |
|
|
|
|
B |
|
|
||
|
The dry cycle controls the cycle time for the drying process. The chart below will help you match the dry setting with |
||||
|
|
||||
|
|
the loads. |
|
|
|
|
|
|
Mixed Loads |
For loads consisting of cottons and poly blends. |
|
|
|
|
Cottons |
For cottons and most linens. NOTE: ENERGY STAR® models are tested on Cottons with default |
|
|
|
|
|
settings. |
|
|
|
|
Heavy duty |
For large coats, bed spreads, mattress covers, sleeping bags, blankets, comforters, jackets, small rugs, |
|
|
|
|
|
and similar large and bulky items. |
|
|
|
|
Towels |
Use for towels OR sheets. It is not recommended to mix towels and sheets in the same load. |
|
|
|
|
Casuals |
For wrinkle-free, permanent press and delicate items, and knits. |
|
|
|
|
Active Wear |
Clothing worn for active sports exercise and some casual wear. Fabrics include new technology |
|
|
|
|
|
finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or Perma Press: For |
|
|
|
|
|
wrinkle-free and permanent press items. |
|
|
|
|
Sanitize |
Reduces certain types of bacteria by 99.6%, including: Staphylococcus aureus and Pseudomonas |
|
|
|
|
|
aeruginosa. The antibacterial process occurs when high heat is used during a portion of this drying |
|
|
|
|
|
cycle. |
|
|
|
|
Quick Dry |
For small loads that are needed in a hurry, such as sports or school uniforms. Can also be used if the |
|
|
|
|
|
previous cycle left some items damp, such as collars or waistbands. |
|
|
|
|
Delicates |
For lingerie and special-care fabrics. |
|
|
|
|
Dewrinkle |
For removing wrinkles from items that are dry or slightly damp. This cycle is not recommended for |
|
|
|
|
|
delicate fabrics. |
|
|
|
|
Warm Up |
Provides 25 minutes of warming time to warm up clothes. |
|
|
|
|
Air Fluff |
Provides 30 minutes of tumbling time without heat. |
|
|
|
|
Rack Dry |
For drying delicate items without tumbling, use drying rack accessory. Place items flat on the drying |
|
|
|
|
|
rack such as wool sweaters and delicate fabrics. Dry with low heat. |
|
|
|
|
Baby Care |
For drying children’s clothes and other small items. |
|
|
|
|
Jeans |
For drying denim and heavy canvas textiles. |
|
|
|
|
Timed Dry |
Use to set your own dry time. Time Dry is also recommended for small loads. To use: |
|
1.Select Timed Dry cycle.
2.Select the drying Time in 10-minute increments up to 2 hours and 30 minutes.
2.Select the dry Temp.
3.Close the door.
4.Press and hold Start.
49-3000195 |
5 |
ENGLISH
ENGLISH
USING THE DRYER
|
|
|
|
|
|
|
|
|
Temp (Temperature) |
|
|
|
C |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
You can change the temperature of your dry cycle. |
||
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
High |
For regular to heavy cottons. |
|
|
|
|
|
|
|
|
|
Medium |
For synthetics, blends and items labeled Permanent Press. |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
Low |
For delicates, synthetics and items labeled Tumble Dry Low. |
|
|
|
|
|
|
|
|
|
No Heat |
This option may only be used with Air Fluff and Timed Dry, in which items are tumbled |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
without heat. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Level |
|
||
D |
|
|||||||||
|
|
|
|
|
|
The sensor continuously monitors the amount of moisture in the load. When the moisture in your |
||||
|
||||||||||
|
|
|
|
|
|
|
clothes reaches your selected dry level, the dryer will stop. |
|||
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
NOTE: Sensor dry Level can be used with all cycles except Timed Dry, Air Fluff, Rack Dry, Warm Up |
|||
|
|
|
|
|
|
|
and Dewrinkle. |
|||
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
Extra Dry |
Use for heavy-duty fabrics or items that should be very dry, such as towels. |
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
Dry |
Use for normal dryness level suitable for most loads. This is the preferred cycle for energy saving. |
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
Less Dry |
Use for lighter fabric (ideal for ironing). |
|
|
|
|
|
|
|
|
|
Damp |
For leaving items partially damp. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delay Dry |
|
E |
||||||||
|
|
|
|
|
|
Use to delay the start of your dryer. |
||
|
||||||||
|
|
|
|
|
|
|
1. Choose your dry cycle and any options. |
|
|
|
|
|
|
|
|
2. In the Delay Dry section. You can change the delay time in 1 hour increments up to 24 hours. |
|
|
|
|
|
|
|
|
3. Press and hold the start ( ) icon for 1 second to start the countdown. The selected delay time will not be |
|
|
|
|
|
|
|
|
shown on the screen. Only the estimated cycle time will be visible. Once the delayed time period has been |
|
|
|
|
|
|
|
|
completed, the selected dry cycle will start. |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
NOTE: If the door is opened while the dryer is in Delay Dry, the countdown time will not restart unless |
|
|
|
|
|
|
|
|
the door is closed and Start icon has been pressed again. |
|
|
|
|
|
|
|
|
Options |
|
F |
|||||||
|
|
|
|
|
|
|
|
Damp Alert |
|
|
|
|
|
|
|
|
This option causes the dryer to beep when clothes have dried to a damp level and the Damp Alert indicator to |
|
|
|
|
|
|
|
|
appear on the screen. Remove items that you wish to hang dry. This feature will only beep when the Damp Alert |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
option is selected. The dryer will continue to dry after the Damp Alert indicator is populated on the screen and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
dryer beeps. Removing clothes and hanging them when they are damp can reduce the need to iron some items. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Extended Tumble |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Minimizes wrinkles by adding approximately 2 hours of no-heat tumbling after clothes are dry. |
|
|
|
|
|
|
|
|
The estimated time remaining display will show “END”. |
|
|
|
|
|
|
|
|
The extended tumble time does not get added to the cycle time on the display. |
|
|
|
|
|
|
|
|
Detangle |
|
|
|
|
|
|
|
|
Activates alternating forward and reverse tumbling to reduce tangling, dry more evenly, and improve |
|
|
|
|
|
|
|
|
drying times. Typical loads such as bed and bath mixed loads, where sheets, towels and pillow cases |
|
|
|
|
|
|
|
|
are laundered together, benefit from this capability. When the dryer reverses direction, there will be a |
|
|
|
|
|
|
|
|
slight pause and sound change. This is normal. |
|
|
|
|
|
|
|
|
NOTE: Detangle is selected by default for Towels and Heavy Duty cycles. |
|
|
|
|
|
|
|
|
eDry |
|
|
|
|
|
|
|
|
Reduces total energy consumption of specific dryer cycles by adjusting certain heat settings. |
|
|
|
|
|
|
|
|
NOTE: Cycle times will change when eDry is selected. |
|
|
|
|
|
|
|
|
ENERGY STAR® models are tested on Cottons cycle with default settings to determine energy use rating of |
|
|
|
|
|
|
|
|
this dryer. The eDry option will default to on for Cottons. Temperature settings on High and dryness level |
|
|
|
|
|
|
|
|
setting on Dry are specifically designed for this cycle to reduce energy consumption. For optimal energy |
|
|
|
|
|
|
|
|
savings, turn eDry on. For optimal drying times, turn eDry off. Energy savings will vary across loads and cycles. |
|
|
|
|
|
|
|
|
The eDry selection can be used with Mixed Loads, Cottons, Heavy Duty, Towels, Casuals, Active |
6 |
|
|
|
|
|
|
Wear and Delicates. |
|
49-3000195 |
USING THE DRYER
G |
My Cycle |
|
My Cycle
Set up your favorite combination of settings for each cycle and save them here for one touch recall. These custom settings can be set while a cycle is in progress. NOTE: you can store one My Cycle combination of settings for each cycle.
To store a My Cycle combination of settings:
1.Select your drying cycle.
2.Change Temp and Level settings to fit your needs.
3.Select any drying options you want.
4.Press and hold the pad for 3 seconds to store your selection. A beep will sound and the icon will light up.
To recall your stored My Cycle combination:
Select the cycle and press the icon before drying a load.
To change your stored My Cycle combination:
Repeat steps 1–4.
HB |
Lock |
Lock |
|
You can lock the controls to prevent any selections from being made. Or you can lock or unlock the |
|
|
|
controls after you have started a cycle. |
|
|
Children cannot accidentally start the dryer by touching pads with this option selected. |
|
|
To lock the dryer, press and hold the lock ( ) pad in the top right corner for 3 seconds and a lock |
|
|
screen will appear. |
|
|
To unlock the dryer controls, press and hold the unlock ( ) pad for 3 seconds and the lock screen will |
|
|
disappear. |
|
|
The control lock icon on the display will light up when it is on. |
|
|
NOTE: The Power button can still be used when the machine is locked. |
I |
Settings |
Settings |
|
Select the gear symbol ( ) in the top right corner to enter the Settings screen. |
|
|
|
Volume |
|
|
When the control panel is powered on, the dryer will beep at the end of the cycle and every time you |
|
|
press a button on the control panel. |
|
|
Use the Option pad to select either High, Med, Low, or Off. |
|
|
NOTE: The selected volume is for both end of cycle and pad sounds. |
|
|
Language |
|
|
Use the Option pad to select either English, Spanish, or French. |
|
|
Brightness |
|
|
To change the brightness of the screen, use the brightness slider to change from darker to brighter. |
|
|
WiFi Connect + Tub Light |
|
|
Use the WiFi Connect + Tub Light toggle button to turn this feature on or off. Toggling this feature on will |
|
|
enable the WiFi Connect function and enable the usage of the tub light when the door is opened & closed. |
|
|
Follow the directions on the Wifi Connect screen using the information provided to connect with the GEA |
|
|
Laundry App. Toggling this feature off will disable the Wifi Connect function and disable the tub light. |
|
|
NOTE: When the dryer to set up with the GEA Laundry App, new software may be available to |
|
|
install. After approving the installation of the new software through the GEA Laundry App, the |
|
|
dryer tub light will flash on and off during the software installation. The dryer tub light will stop |
|
|
flashing and turn off after the software is done installing. |
J |
Start |
Start/Pause |
Start - Press and hold for 1 second to start or restart a cycle. |
||
|
|
Pause - If the dryer is running, press and hold for 1 second to pause the cycle. This function can be |
|
|
used to add garments during a cycle. |
|
|
NOTE: If the dryer is paused and the cycle is not restarted within 15 minutes, the current cycle will be |
|
Pause |
cancelled. |
|
|
ENGLISH
|
|
|
7 |
|
|
|
|
|
|
|
|
49-3000195 |
|
ENGLISH
LOADING
Always follow fabric manufacturer’s care label when laundering.
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.
Dry Labels
|
|
Tumble |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
dry |
|
|
|
|
|
|
|
Do not dry |
|
|
|
|
Dry |
Normal |
Permanent Press/ |
|
|
|
|
||||
|
|
|
Gentle/ Do not tumble dry (used with |
|
||||||||
|
|
|
|
wrinkle resistant |
|
delicate |
do not wash) |
|
||||
|
|
Heat |
|
|
|
|
|
|
|
|
|
|
|
|
setting |
|
|
|
|
|
|
|
|
|
|
|
|
High |
Medium |
|
Low |
|
No heat/air |
|
|
|
||
|
|
Special |
|
|
|
|
|
|
|
|
|
|
|
|
instructions |
Line dry/ |
Drip dry |
Dry flat In the shade |
|
|
|
||||
|
|
|
hang to dry |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sorting and Loading Hints |
|
|
|
|
|
|
|
|||||
|
|
|
- Fire Hazard |
|
|
|
|
|
|
|
||
|
|
WARNING |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Keep flammable materials and vapors, such as gasoline, |
• DO NOT dry anything that has ever had any type of oil on it |
||||||||||
|
|
away from dryer. |
|
|
|
|
|
|
(including cooking oils). |
|
||
|
• DO NOT dry anything that has ever had anything |
• Items containing foam, rubber, or plastic must be dried on a |
|
|||||||||
|
|
flammable on it (even after washing). |
|
|
|
|
clothesline. |
|
||||
|
• No washer can completely remove oil. |
|
|
|
|
• Failure to do so can result in death, explosion, or fire. |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort items according to size. For example, do not dry a sheet with socks or other small items.
Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce® Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the manufacturer’s instructions.
Do not overload. This wastes energy and causes wrinkling.
Drying Rack
A handy drying rack may be used for drying delicate items such as washable sweaters. Place items flat on the drying rack and block such items as wool sweaters and delicate fabrics. Dry with low heat.
To install the drying rack, extend the drying rack into the dryer drum and rest the front two legs on the front angled ledge.
NOTES:
ʄThe drying rack is designed for use with the Timed Dry cycle. Use with sensor cycles may result in damp items or extended cycle times.
ʄDo not use this drying rack when there are other clothes in the dryer, that are not placed on the rack.
ʄThe drying rack, WE01X26416, is available as an accessory. Visit our website at haierappliances.com/parts or in Canada visit haiercanada.ca/parts.
8 |
49-3000195 |
CARE AND CLEANING
Interior and Duct
The interior of the appliance and exhaust duct should be cleaned once a year by qualified service personnel.
The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged exhaust can lengthen the drying time.
The Exhaust Hood: Check with a mirror that the inside flaps of the hood move freely when operating. Make sure that there is no wildlife (birds, insects, etc.) nesting inside the duct or hood.
Exterior
Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty.
Lint Filter
Clean the lint filter before each use.
Pull out the lint filter. Moisten your fingers and remove the captured lint. Once clean, slide the filter back into position. Have a qualified technician vacuum the lint from the dryer once a year.
NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.
Stainless Steel
To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel surfaces. Remove the cleaner residue and then dry with a clean cloth.
The stainless steel used to make the dryer drum provides the highest reliability available in a Haier Appliances dryer. If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface blemishes will not affect the function or durability of the drum.
ENGLISH
49-3000195 |
9 |
ENGLISH
CARE AND CLEANING
Drum Lamp
NOTE: The drum lamp is not consumer replaceable on models where there is a flat cover over an LED bulb. If this light should ever stop working, contact us for service.
For models that have a domed cover over the bulb secured by a screw:
Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker. Reach above dryer opening from inside the drum to locate the light.
Remove the screw and the plastic cover to access the bulb. Replace with the appropriate bulb and then reaffix the cover and screw.
Order replacement bulb WE11X26351 by visiting our website at haierappliances.com/parts or in Canada visit haiercanada.ca/parts. You may also purchase appliance bulb 7C7 from your local retailer.
When the door is opened, the drum lamp automatically turns on and remains on for 2 minutes. When the door is closed, the drum lamp will remain on for 30 seconds.
WARNING - Electrical Shock Hazard
Disconnect power supply before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
10 |
49-3000195 |
INSTALLATION DRYER INSTRUCTIONS
If you have questions, visit our website at haierappliances.com or in Canada visit haiercanada.ca.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT– Save these instructions for local electrical inspector’s use.
• IMPORTANT– Observe all governing codes and ordinances.
•Install the clothes dryer according to the manufacturer’s instructions and local codes.
•Note to Installer – Be sure to leave these instructions with the Consumer.
•Note to Consumer – Keep these instructions for future reference.
•Clothes dryer installation must be performed by a qualified installer.
•This dryer must be exhausted to the outdoors.
•Before the old dryer is removed from service or discarded, remove the dryer door.
•Service information and the wiring diagram are located in the control console.
•Do not allow children on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
•Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not covered under the Warranty.
•Install the dryer where the temperature is above 50°F for satisfactory operation of the dryer control system.
•Remove and discard existing plastic or metal foil duct and replace with UL-listed duct.
WARNING
- Risk of Fire
•Clothes dryer installation must be performed by a qualified installer.
•Install the clothes dryer according to these instructions and local codes.
•DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (semi-rigid or foil-type) duct is installed, it must be UL-listed and installed in accordance with the instructions found in “Connecting the Dryer to House Vent” later in this manual. Flexible venting materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct dryer airflow and increase the risk of fire.
•DO NOT install or store this appliance in any location where it could be exposed to water or weather.
•To reduce the risk of severe injury or death, follow all installation instructions.
•Save these instructions. (Installers: Be sure to leave these instructions with the customer.)
If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer. Kit sold separately.
Visit our website at haierappliances.com/parts or in Canada visit haiercanada.ca/parts.
ENGLISH
49-3000195 |
11 |
ENGLISH
INSTALLATION INSTRUCTIONS
UNPACKING YOUR DRYER
Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them away from the dryer legs. Be sure to remove all of the foam pieces around
the legs. Remove the bag containing the literature.
DRYER
DIMENSIONS |
|
|
|
|
|
|
|
|
||||||||
|
|
23-7/16” |
|
42-13/16” (108.7 cm) |
|
|
||||||||||
|
|
|
||||||||||||||
|
|
|
(59.5 cm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
25-1/4” (64.1 cm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Front |
|
|
View |
*33-1/4” |
*33-1/4” |
|
(84.5 cm) |
(84.5 cm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*NOTE: |
|
|
|
|
Side View |
|
|
|
|
|
||
With leveling legs retracted: 33-1/4 (84.5 cm) |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|||
With leveling legs fully extended: 33-5/8 (85.4 cm) |
|
|
|
|
|
|
|
|
|
|
||
Stacked: 66-1/2” (168.9 cm) |
|
|
|
|
|
|
|
|
|
|
ELECTRICAL CONNECTION
DIMENSIONS 20-1/2”
(52.1 cm)
30” |
Back |
(76.2 cm) |
View |
ACCESSORIES:
Visit our website at haierappliances.com/parts or in Canada visit haiercanada.ca/parts.
Part Number |
Accessory |
PM08X10085 Flexible Metal Dryer Transition Duct
POWER CORDS
Haier Appliances strongly recommends the use of factory specified parts. Select the power cord to fit your installation requirements.
Part Number |
Type |
Length |
Amperage |
WX9X2 |
3-Prong |
4 Feet |
30 |
WX9X3 |
3-Prong |
5 Feet |
30 |
WX9X4 |
3-Prong |
6 Feet |
30 |
WX9X18 |
4-Prong |
4 Feet |
30 |
WX9X19 |
4-Prong |
5 Feet |
30 |
WX9X20 |
4-Prong |
6 Feet |
30 |
Visit our website at haierappliances.com/parts or in Canada visit haiercanada.ca/parts.
12 |
49-3000195 |
INSTALLATION INSTRUCTIONS
REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION
WARNING - Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18” (46 cm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
•The dryer MUST be vented to the outdoors.
•Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:
0” either side
1” front and rear
1” top
•The rear of the dryer should face a wall.
•Consideration must be given to provide adequate clearance for installation and service.
•Closet doors must be louvered or otherwise ventilated and have at least 60 square inches of open area. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches of open area.
NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT THE REAR OF THE DRYER, THE CONFIGURATION OF THE DUCTING MAY REQUIRE GREATER THAN 3” OF REAR CLEARANCE.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATION
Minimum clearance to combustible surfaces and for air opening are: 0” both sides, 1” rear and 1” top.
The rear of the dryer should face a wall.
Consideration must be given to provide adequate clearance for installation and service.
MOBILE OR MANUFACTURED HOME INSTALLATION
•Installation MUST conform to the MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24, PART 3280 or STANDARD FOR MOBILE
HOMES CAN/CSA-Z240 MH, or, when such standards are not applicable, with AMERICAN NATIONAL STANDARD FOR MOBILE HOME, ANSI/ NFPA NO. 501B.
•The dryer MUST be vented to the outdoors.
•The exhaust vent MUST be securely fastened to a non-combustible portion of the mobile home.
•The vent MUST NOT be terminated beneath a mobile or manufactured home.
•The vent duct material MUST BE METAL.
•KIT 14-D346-33 MUST be used to attach the dryer securely to the structure.
•The vent MUST NOT be connected to any other duct, vent or chimney.
•DO NOT use sheet metal screws or other fastening devices which extend into the interior of the exhaust vent.
•Provide an opening with a free area of at least 25 square inches for introduction of outside air into the dryer room.
•See the sections for electrical connection information.
ENGLISH
49-3000195 |
13 |
ENGLISH
INSTALLATION INSTRUCTIONS
UNDERCOUNTER INSTALLATION
If an undercounter installation is desired:
•No special dryer installation kit is required.
•If the dryer is installed alone, a minimum of 60 square inches of open area is required. If a washer and dryer are installed together, a minimum of 120 square inches of open area is required.
Dryer Installed Alone
Countertop and side cabinets
60 |
square |
inches |
min. |
open |
area |
Washer and Dryer Installed Together
Countertop and side cabinets
120 |
square |
inches |
min. |
open |
area |
BATHROOM OR BEDROOM INSTALLATION
The installation must conform with local codes or, in the absence of local codes, with the NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric dryers).
14 |
49-3000195 |
INSTALLATION INSTRUCTIONS
CONNECTING AN ELECTRIC DRYER
TOOLS YOU WILL NEED
ʄ Slip-joint pliers |
ʄ Phillips |
|
screwdriver |
ʄ Flat-blade |
ʄ Level |
screwdriver |
MATERIALS YOU WILL NEED
ʄ4” dia. metal elbow
ʄ3/4” Strain relief (UL recognized)
ʄ4” Duct clamps (2) or 4” spring clamps (2)
ʄSafety glasses
ʄ4” dia. metal duct (recommended)
ʄ4” dia., UL-listed flexible metal duct (if needed)
ʄ4” Cover Plate (Kit WE49X22606) (if needed)
ʄGloves
ʄExhaust hood
ʄDuct tape
ʄDryer power cord kit (not provided with dryer)
UL rated 120/240V, 30A with 3 or 4 prongs. Identify the plug type as
per the house receptacle before purchasing line cord.
Stacking installations may require a power cord up to 6 feet in length.
Before making the electrical connection, turn off the circuit breaker(s) or remove the dryer’s circuit fuse(s) at the electrical box. Be sure the dryer cord is unplugged from the wall. NEVER LEAVE THE ACCESS COVER OFF THE TERMINAL BLOCK.
WARNING - Electrical Shock Hazard
Disconnect power supply before servicing. Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
ENGLISH
49-3000195 |
15 |
ENGLISH
INSTALLATION INSTRUCTIONS
ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS
For electrical connections using a power cord:
WARNING - Fire Hazard
Use a new UL-listed 240V 30 amp dryer power supply cord with closed ring terminals or spade terminals with upturned ends.
Use a UL-listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center terminal.
Ground wire (green or bare wire) must be connected to green ground connector.
Connect remaining two supply wires to remaining two terminals.
Securely tighten all electrical connections. Replace the terminal block cover.
Failure to do so can result in death, fire or electrical shock.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected dryer: This dryer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Improper connection of the
WARNING equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to whether the appliance is properly grounded. DO NOT modify the plug on the power supply cord. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
WARNING - Electrical Shock Hazard
TO PREVENT ELECTRIC SHOCK, DISCONNECT POWER BEFORE SERVICING.
This dryer should be connected to an individual branch circuit with 10 gauge copper wire minimum through a 30 amp fuse or circuit breaker. DO NOT fuse neutral.
Use copper conductors only.
16
ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS
For direct wire connections:
WARNING - Fire Hazard
Use 10 gauge copper wire. Use a UL-listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center terminal.
Ground wire (green or bare wire) must be connected to green ground connector.
Connect remaining two supply wires to remaining two terminals.
Securely tighten all electrical connections. Replace the terminal block cover.
Failure to do so can result in death, fire or electrical shock.
GROUNDING INSTRUCTIONS
For a permanently connected dryer: This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal on the appliance.
Improper connection of the equipment-grounding
conductor can result in a risk of
WARNING electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to whether the appliance is properly grounded.
SAVE THESE INSTRUCTIONS
WARNING - Electrical Shock Hazard
TO PREVENT ELECTRIC SHOCK, DISCONNECT POWER BEFORE SERVICING.
This dryer should be connected to an individual branch circuit with 10 gauge copper wire minimum through a 30 amp fuse or circuit breaker. DO NOT fuse neutral.
Use copper conductors only.
49-3000195
INSTALLATION INSTRUCTIONS
МШЧЧОМЭТЧРНЫвОЫЮЬТЧР$´аТЫО МШЧЧОМЭТШЧ·ЦЮЬЭЛОЮЬОНПШЫ ЦШЛТХОСШЦОТЧЬЭКХХКЭТШЧ¸
NOTE: Since January 1, 1996, the National Electrical Code requires that new constructions use a 4-wire connection to an electric dryer. A 4-wire cord must also be used where local codes do not permit grounding
through the neutral. 3-wire connection is NOT for use on new construction.
White Wire |
L1N L2 |
Black or Red Wire
|
Black |
|
Cover |
or |
|
Red |
|
|
|
Wire |
|
|
Green wire |
3/4” Strain |
|
from power |
Relief and |
|
cord |
Bracket |
4 #10 AWG minimum copper conductors or 120/240V 30A power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied).
1.Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.
2.Be sure the dryer cord is unplugged from the wall receptacle.
3.Remove the power cord cover located at the upper back.
4.Remove green ground screw and retain for use in Step 7. Remove center screw (marked N) in terminal block. Remove and discard ground strap.
5.Install 3/4 in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief and bracket.
6.Connect power cord as follows:
A.Connect the 2 hot lines to the outer screws of the terminal block (marked L1 and L2).
B.Connect the neutral (white) line to the center of the terminal block (marked N).
7.Attach ground wire of power cord with the green ground screw (hole above strain relief bracket). Tighten all terminal block screws (3) securely.
8.Properly secure power cord to strain relief and bracket.
9.Reinstall the cover.
NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.
МШЧЧОМЭТЧРНЫвОЫЮЬТЧР#´аТЫО
CONNECTION
If required, by local code, install external ground (not provided) to grounded metal, cold water pipe, or other established ground determined by a qualified electrician.
Black or Red Wire |
L1N L2 |
White Wire
Black
or Red
Wire Cover
Ground
Strap
3/4” Strain
Relief and
Bracket
3 #10 AWG minimum copper conductors or 120/240V 30A power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied).
3-wire Connection
Not for use in Canada.
DO NOT use for Mobile Home Installations. NOT for use on new construction.
NOT for use on recreational vehicles.
NOT for use in areas where local codes prohibit grounding through the neutral conduction.
1.Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.
2. Be sure the dryer cord is unplugged from the wall receptacle.
3.Remove the power cord cover located at the upper back.
4.Install 3/4-in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief and bracket.
5.Connect power cord as follows:
A.Connect the 2 hot lines to the outer screws of the terminal block (marked L1 and L2).
B.Connect the neutral (white) line to the center of the terminal block (marked N).
6. Be sure ground strap is connected to green ground screw on cabinet rear. Tighten all terminal block screws (3) securely.
7.Properly secure power cord to strain relief and bracket.
8.Reinstall the cover.
NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.
ENGLISH
49-3000195 |
17 |
ENGLISH
INSTALLATION INSTRUCTIONS EXHAUSTING THE DRYER
WARNING - Fire Hazard
This dryer MUST be vented to the outdoors.
Use only 4” rigid metal ducting for the home exhaust duct.
Use only 4" rigid metal, UL-listed flexible metal, or UL-listed metal foil dryer transition duct to connect the dryer to the home exhaust.
DO NOT use any plastic to vent the dryer, this includes the home exhaust duct, dryer transition duct, or within the dryer.
DO NOT use flexible metal or metal foil ducting for a home exhaust duct or within the dryer.
DO NOT exhaust into a chimney, kitchen exhaust, gas vent, wall, ceiling, attic, crawl space, or concealed space of a building.
DO NOT install a screen in or over the exhaust duct.
DO NOT install a booster fan in the exhaust duct.
DO NOT use duct longer than specified in the exhaust length table.
Failure to follow these instructions can result in death or fire.
TOOLS AND MATERIALS YOU WILL NEED TO INSTALL EXHAUST DUCT
ʄ Phillips-head |
ʄ Drill with 1/8” drill bit |
screwdriver |
(for bottom venting) |
ʄ Duct tape or |
ʄ Hacksaw |
duct clamp |
ʄ Rigid or UL-listed flexible
metal 4” (10.2 cm) duct
ʄ Vent hood
VISIT HAIERAPPLIANCES.COM/PARTS OR IN CANADA VISIT HAIERCANADA.CA/PARTS
PM8X85 Outdoor exhaust hood
PM08X10085 8’ Flexible metal clothes dryer transition duct with 2 clamps
WX08X10130 4” Dryer exhaust clamp
WE49X22606 Rear exhaust opening cover, for side or bottom vented dryers
CONNECTING THE DRYER TO HOUSE VENT
RIGID METAL TRANSITION DUCT
•For best drying performance, a rigid metal transition duct is recommended.
•Rigid metal transition ducts reduce the risk of crushing and kinking.
UL-LISTED FLEXIBLE METAL CLOTHES DRYER TRANSITION DUCT
•If rigid metal cannot be used, then UL-listed flexible metal clothes dryer transition duct (Haier Appliances part – PM08X10085) can be used.
•Never install transition duct in walls, ceilings, floors or other enclosed spaces.
•Total length of transition duct should not exceed 8’ (2.4 m).
•For many applications, installing elbows at both the dryer and the wall is highly recommended (see illustrations in next section). Elbows allow the dryer to sit close to the wall without kinking and/or crushing
the transition duct, maximizing drying performance.
•Avoid resting the duct on sharp objects.
UL-LISTED FLEXIBLE METAL (FOIL-TYPE) TRANSITION DUCT
•In special installations, it may be necessary to connect the dryer to the home exhaust vent using flexible metal (foil-type) transition duct. UL–LISTED universal flexible dryer transition duct (Haier Appliances parts – PM8X73 or WX8X73) may be used ONLY in installations where rigid metal or flexible metal transition ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct.
•In Canada and the United States, only transition ducts that comply with “UL 2158A STANDARD FOR CLOTHES DRYER TRANSITION DUCT” shall be used.
•Avoid resting the duct on sharp objects.
•For best drying performance:
1.Slide one end of the duct over the clothes dryer outlet pipe.
2.Secure the duct with a clamp.
3.With the dryer in its permanent position, extend the duct to its full length. Allow 2” of duct to overlap the exhaust pipe. Cut off and remove excess duct. Keep the duct as straight as possible for maximum airflow.
4.Secure the duct to the exhaust pipe with the other clamp.
18 |
49-3000195 |
INSTALLATION INSTRUCTIONS
EXHAUSTING THE DRYER (cont.)
•DO cut duct as short as possible and install straight into wall.
• DO use elbows when turns are necessary.
Elbows |
• DO NOT bend |
• DO NOT use |
• DO NOT |
• DO NOT |
or collapse |
excessive |
crush duct |
set dryer |
ducting. Use |
exhaust |
against |
on duct. |
elbows if turns |
length. Cut |
the wall. |
|
are necessary. |
duct as short |
|
|
|
as possible. |
|
|
EXHAUST LENGTH
Using exhaust longer than specified length will:
•Increase the drying times and the energy cost.
•Reduce the dryer life.
•Accumulate lint, creating a potential fire hazard.
The correct exhaust installation is YOUR RESPONSIBILITY.
Problems due to incorrect installation are not covered by the warranty.
The MAXIMUM ALLOWABLE length of the exhaust system depends upon the type of duct, number of turns, the type of exhaust hood (wall cap) and all conditions noted on the chart.
•Internal elbows added for side or bottom vent conversions must be included in the total elbow count.
•Any elbow greater than 45° should be treated as a 90° elbow; one elbow of 45° or less may be ignored.
•Two 45° elbows will be treated like one 90° elbow.
•For the side exhaust installations, add one 90° elbow to the chart.
•For every additional 90° elbow, reduce the allowable vent system length by 10 feet.
•When calculating the total vent system length, you must add all the straight portions and elbows of the system (including the transition duct).
|
|
RECOMMENDED MAXIMUM LENGTH |
||
|
|
Exhaust Hood Types |
||
|
Recommended |
Use only for short run |
||
EXHAUST |
installations |
|||
4" DIA. |
4" DIA. |
|||
LENGTH |
4" DIA. |
|||
|
|
|
||
|
|
4" |
2-1/2" |
|
|
|
|
||
No. of 90° Elbows |
Rigid Metal |
Rigid Metal |
||
0 |
|
90 Feet |
60 Feet |
|
1 |
|
60 Feet |
45 Feet |
|
2 |
|
45 Feet |
35 Feet |
|
3 |
|
35 Feet |
25 Feet |
|
4 |
|
25 Feet |
15 Feet |
ENGLISH
49-3000195 |
19 |
ENGLISH
INSTALLATION INSTRUCTIONS
EXHAUSTING THE DRYER (cont.)
EXHAUST SYSTEM CHECKLIST
HOOD OR WALL CAP
•Terminate in a manner to prevent back drafts or entry of birds or other wildlife.
•Termination should present minimal resistance to the exhaust airflow and should require little or no maintenance to prevent clogging.
•Wall caps must be installed at least 12” above ground level or any other obstruction with the opening pointed down.
SEPARATION OF TURNS
•For best performance, separate all turns by at least 4 ft. of straight duct, including distance between last turn and dampened exhaust hood (wall cap).
SEALING OF JOINTS
•All joints should be tight to avoid leaks. The male end of each section of duct must point away from the dryer.
•Duct joints should be made airand moisture-tight by wrapping the overlapped joints with duct tape or aluminum tape.
•Do not assemble ductwork with any fasteners that extend into the duct. These fasteners can accumulate lint, creating a potential fire hazard.
•Horizontal runs should slope down towards the outdoors 1/4” per foot.
•Provide an access for inspection and cleaning of the exhaust system, especially at turns and joints. Exhaust system shall be inspected and cleaned at least once a year.
INSULATION
•Ductwork that runs through an unheated area or is near air conditioning should be insulated to reduce condensation and lint build-up.
BEFORE YOU BEGIN
•Remove and discard existing plastic or metal foil duct and replace with UL-listed duct.
•Remove any lint from the wall exhaust opening.
Wall
Internal
Duct
Opening
Check that exhaust
hood damper opens
and closes freely.
STANDARD REAR EXHAUST
We recommend that you install your dryer before installing your washer. This will permit direct access for easier exhaust connection.
Slide the end of the exhaust duct on the back of the dryer and secure with duct tape or a hose clamp.
Duct
NOTE: We strongly recommend using rigid metal exhaust duct. However, if flexible ducting is used it must be UL-Listed metal, not plastic.
•For straight line installation, connect the dryer exhaust to the external exhaust hood using duct tape or clamp.
Wall Side
Duct Tape
Dryer
Side
RECOMMENDED CONFIGURATION TO MINIMIZE EXHAUST BLOCKAGE
Using duct elbows will prevent duct kinking and collapsing.
Wall
Transition
Ducting
20 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
49-3000195 |
INSTALLATION INSTRUCTIONS
EXHAUSTING THE DRYER (cont.)
SIDE OR BOTTOM VENTING
WARNING - Fire Hazard
Disconnect dryer from electrical supply. Wear gloves and arm guards.
Close the back opening with cover plate (Kit WE49X22606).
Failure to do so may result in fire, electrical shock or lacerations.
Remove
screw Right and save
Left
Bottom
Remove desired knockout (one only)
Detach and remove the right, left or bottom knockout as desired. Remove the screw inside the dryer exhaust duct and save.
Pull the duct out of the dryer.
Cut the duct as shown and keep portion A.
Fixing hole
A
9” (22.86cm)
SIDE OR BOTTOM VENTING (cont.)
ADDING A NEW DUCT
Portion “A”
Fixing hole
Right
Right or left side exhaust
Left
Reconnect the cut portion (A) of the duct to the blower housing. Make sure that the shortened duct is aligned with the tab in the base. Use the screw saved previously to secure the duct in place through the tab on the appliance base.
ADDING ELBOW AND DUCT FOR EXHAUST TO RIGHT OR LEFT SIDE OF CABINET
Right
Exhaust can be added to right or left side
Left Duct
tape
•Preassemble 4” elbow with 4” duct. Wrap duct tape around joint.
•Тсцихчзшжчдццирепь ипетъĤхцч члхтшклчлицмзи opening and connect the elbow to the dryer internal duct.
Be sure not to pull or damage the electrical wires inside the dryer when inserting the duct.
ENGLISH
49-3000195 |
21 |
ENGLISH
INSTALLATION INSTRUCTIONS
EXHAUSTING THE DRYER (cont.)
SIDE OR BOTTOM VENTING (cont.)
ADDING ELBOW AND DUCT FOR EXHAUST TO LEFT OR RIGHT SIDE OF CABINET (cont.)
• Apply duct tape as shown |
|
|
DUCT |
||
on the joint between the |
|
|
TAPE |
||
dryer internal duct and the |
|
|
|
|
|
elbow, and also the joint |
|
|
|
|
|
|
|
|
|
|
|
between the elbow and |
|
|
|
|
|
|
|
|
|
|
|
the side duct. |
|
|
|
|
Use 4” rigid metal ducting
only inside the dryer. Internal duct joints must be secured with tape, otherwise they may separate and cause a safety hazard.
ADDING ELBOW FOR EXHAUST THROUGH BOTTOM OF CABINET
•Insert the elbow through the rear opening and connect it to the dryer internal duct.
• Apply duct tape as |
Duct tape |
shown on the joint |
|
between the dryer |
|
internal duct and the |
|
elbow, and also the joint |
|
between the elbow and |
|
the bottom duct. |
|
Internal duct joints must
be secured with tape; otherwise, they may separate and cause a safety hazard.
SIDE OR BOTTOM VENTING (cont.)
ADDING COVER PLATE TO REAR OF CABINET
Plate
(Kit WE49X22606)
Connect standard metal elbows and ducts to complete the exhaust system. Cover back opening with the
plate (kit WE49X22606) which can be purchased from haierappliances.com/parts or in Canada visit haiercanada.ca/parts. It may also be obtained from a local service provider. Place dryer in final location.
NEVER LEAVE THE BACK OPENING WITHOUT THE PLATE.
22 |
49-3000195 |
INSTALLATION INSTRUCTIONS
FINAL SETUP
1 LEVEL THE DRYER
Stand the dryer upright near the final location and adjust the four leveling legs at the corners to ensure that the dryer is level from side to side and front to rear.
Lower Raise
2 PLUG DRYER IN
NOTE: Stacking installations may require a power cord up to 6 feet in length.
Ensure proper ground exists before use.
3 DRYER START-UP
Press and hold the power button.
NOTE: If the dryer has been exposed to temperatures below freezing for an extended period of time, allow it to warm up before pressing Power. Otherwise, the display will not come on.
The dryer is now ready for use.
WARNING - Electrical Shock Hazard
Disconnect power supply before servicing. Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
ENGLISH
49-3000195 |
23 |
ENGLISH
INSTALLATION INSTRUCTIONS
STACKING THE WASHER AND DRYER (if desired)
If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer. Kit sold separately.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT– Save these instructions for local electrical inspector’s use.
• IMPORTANT– Observe all governing codes and ordinances.
•Note to Installer – Be sure to leave these instructions with the Consumer.
•Note to Consumer – Keep these instructions for future reference.
•Service must be performed by a qualified installer.
•Do not allow children on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
•Proper installation is the responsibility of the installer.
HAIER APPLIANCES STACK KIT
Visit our website at haierappliances.com/parts or in Canada visit haiercanada.ca/parts.
Part Number |
Accessory |
GFA24KITL |
Complete Stack Kit |
KIT CONTENTS (HAIER APPLIANCES KIT # GFA24KITL)
Screws (2) Long For dryer
attachment
Bracketstack (L)
Bracket- |
Screws (6) Short |
stack (R) |
For washer attachment |
TOOLS YOU WILL NEED
ʄ Phillips |
ʄ Level |
ʄ Gloves |
screwdriver |
|
|
REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION
WARNING - Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18” (46 cm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
•The dryer MUST be vented to the outdoors.
•Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:
0” either side 1” front and rear 1” top
•The rear of the dryer should face a wall.
•Consideration must be given to provide adequate clearance for installation and service.
•Closet doors must be louvered or otherwise ventilated and have at least 60 square inches of open area. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches of open area.
NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT THE REAR OF THE DRYER, THE CONFIGURATION OF THE DUCTING MAY REQUIRE GREATER THAN 3” OF REAR CLEARANCE.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATION
Minimum clearance to combustible surfaces and for air opening are: 0” both sides, 1” rear and 1” top.
The rear of the dryer should face a wall.
Consideration must be given to provide adequate clearance for installation and service.
INSTALLATION PREPARATION
Remove the packaging.
Flatten the product carton to use as a pad to lay the dryer down on its side. Continue using the carton to protect the finished floor in front of the installation location.
24 |
49-3000195 |
INSTALLATION INSTRUCTIONS
INSTALLING THE STACK BRACKET KIT
1INSTALL BRACKET TO WASHER
A.Remove washer top cap screw from the rear left. Align left bracket holes with top cap screw hole on rear left of the unit and replace screw.
NOTE: Leave screws loose so dryer hole alignment will be easier.
B.Drive next screw through the bracket into the rear of the washer.
C.Repeat the above steps with the right side.
Short screws into brackets and washer
Washer
Top
2INSTALL DRYER AND BRACKET ON DRYER
Disconnect power before installing. WARNING Failure to do so could result in
serious injury or death.
- Excessive Weight
WARNING Hazard
Failure to do so may result in back or other injury, or property damage.
•Use two or more people to install dryer.
•Avoid tipping and rupture of utility services.
•Dryer must be securely attached to the washer.
•DO NOT place the washer on top of the dryer.
A.Lift the dryer on top of the washer. Protect the washer control panel with cardboard or other protection. Be sure to lift the dryer high enough to clear the washer control panel.
B.Align the holes in the bracket with the holes in the back of the dryer. Using a Phillips screwdriver, attach the 2 #8 x 1/2” tapping screws.
2INSTALL DRYER AND BRACKET ON DRYER (CONT.)
C.Tighten the dryer bracket screws; then tighten all stacking kit screws.
Long screws into brackets and dryer
3 FINALIZE THE INSTALLATION
Do not push on the dryer once CAUTION installed to top of the washer.
Pushing on the dryer may result in pinched fingers.
A.Refer to the washer Installation Instructions to complete the washer installation.
B.Refer to the dryer Installation Instructions to complete the dryer installation.
C.Carefully slide or walk the stacked washer and dryer into place. Use felt pads or other sliding device to assist moving and to protect flooring.
Dryer
Place |
Place |
hands |
hands |
here |
here |
Washer
ENGLISH
49-3000195 |
25 |
ENGLISH
INSTALLATION INSTRUCTIONS
REVERSING THE DOOR SWING (Optional)
IMPORTANT NOTES
•Before you start, unplug the dryer from its electrical outlet.
•Handle parts carefully to avoid scratching paint.
•Provide a non-scratching work surface for the doors.
•Tools you will need: Phillips-head screwdriver.
•Once you begin, do not move the cabinet until doorswing reversal is completed.
•These instructions are for changing the hinges from the right side to the left side—if you ever want to switch them back to the right side, follow these same instructions and reverse all references to the left and right.
1REMOVE THE DOOR ASSEMBLY
•Open the door. Remove the two screws holding the hinge/door assembly to the dryer. Carefully set the hinge/door assembly aside.
Hinge and Door
Assembly
Hold the Door and
Remove Hinge Screws
from the Dryer
2REMOVE, ROTATE AND REPLACE THE STRIKE PLATE
•Remove the two screws holding the strike plate. Rotate it and install it on the opposite side.
Strike Plate
and Screws
Reinstall
Strike Plate
and Screws
3REMOVE, ROTATE AND REPLACE THE INNER DOOR
•Remove the six screws securing the inner door to the outer door. Remove the inner door, rotate it 180o and reinstall it into the outer door using the same six screws.
Remove six |
Inner door shown |
Replace the |
screws and the |
inner door and |
|
inner door |
rotated 180o |
six screws |
4ROTATE AND REPLACE THE HINGE/ DOOR ASSEMBLY
•Rotate and replace the hinge/door assembly, on the opposite side, using the same two screws.
Secure with same two screws
26 |
49-3000195 |
NOTES
ENGLISH
49-3000195 |
27 |
ENGLISH
TROUBLESHOOTING TIPS
Problem |
Possible Cause |
What To Do |
|
Dryer shakes or |
Some shaking/noise is normal. |
Move dryer to an even floor space, or adjust leveling legs as necessary |
|
makes noise |
Dryer may be sitting unevenly. |
until even. |
|
Clothes take too |
Improper or obstructed |
Check the Installation Instructions to make sure the dryer venting is |
|
long to dry |
ducting |
correct. |
|
|
|
Make sure ducting is clean, free of kinks and unobstructed. |
|
|
|
Check to see if outside wall damper operates easily. |
|
|
Improper sorting |
Separate heavy items from lightweight items (generally, a well-sorted |
|
|
|
washer load is a well-sorted dryer load). |
|
|
Large loads of heavy fabrics |
Large, heavy fabrics contain more moisture and take longer to dry. |
|
|
(like beach towels) |
Separate large, heavy fabrics into smaller loads to speed drying time. |
|
|
Controls improperly set |
Match control settings to the load you are drying. |
|
|
Lint filter is full |
Clean lint filter before every load. |
|
|
Blown fuses or tripped circuit |
Replace fuses or reset circuit breakers. Since most dryers use 2 fuses/ |
|
|
breaker |
breakers, make sure both are operating. |
|
|
Overloading/combining loads |
Do not put more than one washer load in the dryer at a time. |
|
|
Underloading |
If you are drying only one or two items, add a few items to ensure proper |
|
|
|
tumbling. |
|
The Dry dryness |
Load consists of a mixture of |
When combining heavy and light fabrics in a load, choose More Dry. |
|
level was chosen |
heavy and light fabrics |
|
|
but load is still |
|
|
|
Lint filter is blocked |
Inspect and clean lint filter. |
||
damp |
|
|
|
Dry Sensor is dirty |
Clean the sensor with a moist cloth. |
||
|
|||
Control buttons |
Controls accidentally put in |
Press Start/Pause. |
|
not responding |
service mode |
|
|
|
Controls accidentally put in |
Hold the Lock Control button for 3 seconds to unlock the dryer. |
|
|
lock mode |
|
|
|
Controls performed an |
Reset the in-house breaker. |
|
|
incorrect operation |
|
|
Dryer doesn’t |
Control panel is “asleep” |
This is normal. Press Power to activate the control panel. |
|
start |
Dryer is unplugged |
Make sure the dryer plug is pushed completely into the outlet. |
|
|
Fuse is blown/circuit breaker is |
Check the building’s fuse/circuit breaker box and replace fuse or reset |
|
|
tripped |
breaker. NOTE: Electric dryers use two fuses or breakers. |
|
|
Dryer was accidentally paused |
If the light on the Start/Pause button is flashing, the dryer is paused. |
|
|
when starting Delay Dry |
Press Start/Pause to restart the countdown. |
|
No numbers |
Dryer is continuously |
This is normal. When the dryer senses a low level of moisture in the load, |
|
displayed during |
monitoring the amount of |
the dryer will display the dry time remaining. |
|
cycle, only lights |
moisture in the clothes |
|
28 |
49-3000195 |
TROUBLESHOOTING TIPS
Problem |
Possible Causes |
What To Do |
Time Remaining |
The estimated time may |
This is normal. |
jumped to a |
change when a smaller load |
|
lower number |
than usual is drying |
|
Cannot make |
The dryness Level, Temp or |
This is normal. |
a selection and |
option that you are trying to |
|
the dryer beeps |
select is incompatible with the |
|
twice |
chosen dry cycle |
|
Dryer is running |
The Ext Tumble option was |
This is normal. During extended tumbling, the time remaining is not |
but 00 is |
chosen |
displayed. The extended tumbling option lasts approximately 60 minutes. |
displayed in Time |
|
|
Remaining |
|
|
Clean Lint Filter |
Power button was activated |
Press Start/Pause to begin a dry cycle and the message will disappear. |
(message) |
|
|
Dryer doesn’t |
Fuse is blown/circuit breaker is |
Check the building’s fuse/circuit breaker box and replace both fuses or |
heat |
tripped; the dryer may tumble |
reset both breakers. Your dryer may tumble if only one fuse is blown or |
|
but not heat |
one breaker tripped. |
Inconsistent |
Type of load and drying |
The load size, types of fabric, wetness of clothes and the condition of the |
drying times |
conditions |
lint filter and/or air intake vent located on the front of the dryer will |
|
|
affect drying times. |
|
Type of load and drying |
The load size, types of fabric, wetness of clothes and the length and |
|
conditions |
condition of the exhaust system will affect drying times. |
Glow at the rear |
Heaters behind the drum |
This is normal. Under certain drying conditions and room ambient |
of the drum |
|
lighting, the glow of the heaters may be visible at the rear of the drum. |
Clothes are still |
The door was opened mid- |
A dry cycle must be reselected each time a new load is put in. |
wet and dryer |
cycle. The load was then |
|
shut off after a |
removed from the dryer and |
|
short time |
a new load put in without |
|
|
selecting a new cycle |
|
|
Small load |
When drying 3 items or less, choose Quick Dry or Time Dry. |
|
Load was already dry except for |
Choose Quick Dry or Time Dry to dry damp collars and waistbands. In |
|
collars and waistbands |
the future, when drying a load with collars and waistbands, choose More |
|
|
Dry. |
|
Dryer is not level |
Move dryer to an even floor space or adjust leveling legs as necessary |
|
|
until even. |
Clothes are |
Overdrying |
Select a shorter drying time. |
wrinkled |
|
Remove items while they still hold a slight amount of moisture. Select a |
|
|
Less Dry or Damp setting. |
|
Letting items sit in dryer after |
Remove items when cycle ends and fold or hang immediately, or use the |
|
cycle ends |
Ext Tumble option. |
|
Overloading |
Separate large loads into smaller ones. |
ENGLISH
49-3000195 |
29 |
ENGLISH
TROUBLESHOOTING TIPS
Problem |
Possible Causes |
What To Do |
||||||
Clothes shrink |
Some fabrics will naturally |
To avoid shrinkage, follow garment care labels exactly. |
|
|||||
|
shrink when washed. Others |
Some items may be pressed back into shape after drying. |
||||||
|
can be safely washed, but will |
If you are concerned about shrinkage in a particular |
||||||
|
shrink in the dryer. |
|||||||
|
|
item, do not machine wash or tumble dry it. |
||||||
Greasy spots on |
Improper use of fabric softener |
Follow directions on fabric softener package. |
|
|||||
clothes |
Drying dirty items with clean |
Use your dryer to dry only clean items. Dirty items can stain clean items |
|
|||||
|
ones |
and the dryer. |
||||||
|
Clothes were not completely |
Sometimes stains which cannot be seen when the clothes are wet |
|
|||||
|
clean |
appear after drying. Use proper washing procedures before drying. |
||||||
Lint on clothes |
Lint filter is full |
Clean lint screen before each load. |
|
|||||
|
Improper sorting |
Sort lint producers (like chenille) from lint collectors (like corduroy). |
|
|||||
|
Static electricity can attract lint |
See suggestions in this section under Static occurs. |
|
|||||
|
Overloading |
Separate large loads into smaller ones. |
|
|||||
|
Paper, tissue, etc., left in |
Empty all pockets before laundering clothes. |
|
|||||
|
pockets |
|
|
|
|
|
|
|
Static occurs |
No fabric softener was used |
Try a fabric softener. |
|
|||||
|
|
Bounce® Fabric Conditioner Dryer Sheets have been approved for |
||||||
|
|
use in all Haier Appliances dryers when used in accordance with the |
||||||
|
|
manufacturer’s instructions. |
||||||
|
Overdrying |
Try a fabric softener. |
|
|||||
|
|
Adjust setting to Õèöö Íõüor Damp. |
||||||
|
Synthetics, permanent press |
Try a fabric softener. |
|
|||||
|
and blends can cause static |
|
|
|
|
|
|
|
Collars and |
The dryness monitor senses |
Choose Quick Dry or Time Dry to dry damp collars and waistbands. In |
|
|||||
waistbands still |
that the body of the clothes is |
the future, when drying a load with collars and waistbands, choose More |
||||||
wet at end of |
dry |
Dry. |
||||||
cycle |
|
|
|
|
|
|
|
|
Slight variation |
This is normal |
Due to the metallic properties of paint used for this unique product, |
|
|||||
in metallic color |
|
slight variations of color may occur due to viewing angles and lighting |
||||||
|
|
conditions. |
||||||
Dryer continues |
Ext Tumble was selected |
Ensure Ext Tumble option is not selected. |
|
|||||
to tumble after |
|
|
|
|
|
|
|
|
display says |
|
|
|
|
|
|
|
|
Complete |
|
|
|
|
|
|
|
|
30 |
49-3000195 |