Graco 24K632, 24K633 Kit Instructions

Kit Instructions

Leg Replacement Kit for
Airless Sprayers

- For Portable Spray Applications Architectural Paints and Coatings -

- Not for use in explosive atmospheres -

Models 24K632 and 24K633

Important Safety Instructions

Read all warnings and instructions in this
manual. Save these instructions.

Pressure Relief Procedure

To help prevent injection injuries, follow this
procedure when you stop spraying and before
you service or clean the sprayer, remove
parts, or repair leaks.

1. Turn Power switch OFF. Unplug sprayer.

2. Turn Spray/Prime valve to PRIME to relieve pres­sure. Turn pressure control knob left (counterclock­wise) to minimize pressure.

3A1964A

EN

Model 24K632

ti17726a

Model 24K633

3. Trigger gun.

4. Put trigger safety in safety ON position.

NOTE: Leave Spray/Prime valve in the PRIME
position until you are ready to spray again.

If you suspect that the spray tip or hose is completely
clogged or that pressure has not been fully relieved
after following the steps above, VERY SLOWLY loosen

the tip guard retaining nut or hose end coupling to
relieve pressure gradually. Then loosen it completely.
Clear the tip or hose obstruction.

ti11868a

Disassembly

Disassembly

Remove Shroud

1. Unplug electrical cord and perform Pressure Relief
Procedure (see cover).

2. Remove side shroud screws (E) (T-20 Torx).
NOTE: Number of side shroud screws may vary
from image shown.

3. Remove 4 front cover screws (B) (T-30 Torx).

4. Remove right shroud (G).

5. Remove left shroud (K).

6. Remove ON/OFF (L) switch from left shroud (K).

E

G

B

For Metal Legs:

1. Remove hex head bolts (S). NOTE: Number of hex
head bolts will vary depending on model.

2. Remove leg (M) from sprayer frame (F).

M

S

F

ti17728a

For Plastic Legs:

1. Remove nuts (R) and bolts (T).

2. Remove leg (W) from frame (F).

N

ti17751a

L

K

R

F

T

W

ti17727a

2 3A1964A

Assembly

Assembly

Install Leg

1. Slide leg (M) onto sprayer frame (F).

2. Install carriage head bolts and hex nuts (S) and
torque to 26 to 32 in-lb (2.9 to 3.6 N•m).

F

M

ti17727a

NOTICE

Do not over-tighten. Plastic will become stripped
and damage to sprayer will occur.

Replace Shroud

1. Install ON/OFF switch (L) into left shroud (K).

2. Install power cord (N) into recess on left shroud (K).

3. Reassemble both shrouds (G and K).

4. Install side shroud screws (E) (T-20 Torx). Torque to
20 to 25 in-lb (2.3 to 2.8 N•m).

5. Install 4 front cover screws (B) (T-30 Torx). Torque to
26 to 32 in-lb (2.9 to 3.6 N•m).

E

S

G

N

B

L

ti17751a

K

3A1964A 3

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 3A1964

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2011, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

Graco Headquarters: Minneapolis

www.graco.com

Revision A - 08/2011