Graco Inc AirPro 312579, AirPro 312579H User Manual

Size:
1.37 Mb
Download

Instructions-Parts

AirProGravity

Feed Airspray Gun

312579H

ENG

Conventional, HVLP, and compliant guns for specialty industrial applications. For professional use only.

100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

See page 3 for model information.

ti11095A

ll 2 G

Related Manuals

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Gravity Feed without Cup . . . . . . . . . . . . . . . . . . 3

Gravity Feed with Plastic Cup . . . . . . . . . . . . . . . 3

Gravity Feed with 3MPPSCup . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Gun Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Conventional Guns . . . . . . . . . . . . . . . . . . . . . . . 5

HVLP Guns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Compliant Guns . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Ground the Gun . . . . . . . . . . . . . . . . . . . . . . . . . 6

Flush Before Using Equipment . . . . . . . . . . . . . . 6

Adjust Spray Pattern . . . . . . . . . . . . . . . . . . . . . . 7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pressure Relief Procedure . . . . . . . . . . . . . . . . . 8

Apply Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Volatile Organic Compounds (VOC) Regulation . 8

Related Manuals

Manual

Language

 

 

313089

Chinese

 

 

313091

Dutch

 

 

313092

Finnish

 

 

313093

French

 

 

313094

German

 

 

313096

Italian

 

 

313097

Japanese

 

 

313098

Korean

 

 

313100

Portuguese

 

 

313101

Russian

 

 

313102

Spanish

 

 

313103

Swedish

 

 

Daily Gun Maintenance . . . . . . . . . . . . . . . . . . . . . . 9

General Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Clean Gun and Cup . . . . . . . . . . . . . . . . . . . . . . . 9

Clean Nozzle and Air Cap . . . . . . . . . . . . . . . . . 10

Compliant Cleaning Methods . . . . . . . . . . . . . . 10

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 12

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fluid Inlet Fitting Replacement . . . . . . . . . . . . . 14

Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Repair Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 22

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 22

2

312579H

Models

Models

Gravity Feed without Cup

 

 

Conventional

 

HVLP

 

Compliant

 

 

 

 

 

 

 

 

 

 

 

 

 

Max.

 

 

Max.

 

 

Max.

Orifice

 

 

HVLP/Compliant

 

 

HVLP/Compliant

 

 

HVLP/Compliant

Size

 

 

Air Pressure

 

 

Air Pressure

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

 

 

 

 

 

 

 

 

 

 

0.055 (1.4)

289002

A

N/A

289005

A

29 (0.2, 2.0)

289008

A

35 (0.24, 2.4)

0.070 (1.8)

289003

A

N/A

289006

A

29 (0.2, 2.0)

289009

A

35 (0.24, 2.4)

 

 

 

 

 

 

 

 

 

 

Gravity Feed with Plastic Cup

 

 

Conventional

 

HVLP

 

Compliant

 

 

 

 

 

 

 

 

 

 

 

 

 

Max.

 

 

Max.

 

 

Max.

Orifice

 

 

HVLP/Compliant

 

 

HVLP/Compliant

 

 

HVLP/Compliant

Size

 

 

Air Pressure

 

 

Air Pressure

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

 

 

 

 

 

 

 

 

 

 

0.055 (1.4)

289011

A

N/A

289014

A

29 (0.2, 2.0)

289017

A

35 (0.24, 2.4)

0.070 (1.8)

289012

A

N/A

289015

A

29 (0.2, 2.0)

289018

A

35 (0.24, 2.4)

 

 

 

 

 

 

 

 

 

 

Gravity Feed with 3MPPSCup

 

 

Conventional

 

HVLP

 

Compliant

 

 

 

 

 

 

 

 

 

 

 

 

 

Max.

 

 

Max.

 

 

Max.

Orifice

 

 

HVLP/Compliant

 

 

HVLP/Compliant

 

 

HVLP/Compliant

Size

 

 

Air Pressure

 

 

Air Pressure

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

 

 

 

 

 

 

 

 

 

 

0.055 (1.4)

289020

A

N/A

289023

A

29 (0.2, 2.0)

289026

A

35 (0.24, 2.4)

0.070 (1.8)

289021

A

N/A

289024

A

29 (0.2, 2.0)

289027

A

35 (0.24, 2.4)

 

 

 

 

 

 

 

 

 

 

312579H

3

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specificrisks. Refer back to these warnings. Additional, productspecific warnings may be found throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

Keep work area free of debris, including solvent, rags and gasoline.

Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

Ground all equipment in the work area. See Grounding instructions.

If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

Keep a working fire extinguisher in the work area.

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

Tighten all fluid connections before operating the equipment.

Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not alter or modify equipment.

Use equipment only for its intended purpose. Call your Graco distributor for information.

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

Do not kink or overbend hoses or use hoses to pull equipment.

Keep children and animals away from work area.

Comply with all applicable safety regulations.

4

312579H

Gun Selection

WARNING

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

Protective eyewear

Clothing and respirator as recommended by the fluid and solvent manufacturer

Gloves

Hearing protection

Gun Selection

Conventional Guns

Excellent atomization and high production rates typically with some reduction in transfer efficiency.

HVLP Guns

An HVLP gun is a high transfer efficiency gun which limits the air pressure at the air cap to

10 psi (0.07 MPa, 0.7 bar) maximum. In some areas, an HVLP gun is required for compliance with environmental standards.

Compliant Guns

A compliant gun is a high transfer efficiency gun which has been tested to have a transfer efficiency greater than or equal to HVLP guns.

The Graco compliant guns have no restrictions on air cap pressures, but the gun inlet pressure must remain under 35 psi (0.24 MPa,

2.4 bar) to remain in compliance.

312579H

5

Setup

Setup

• Check that your shop air provides adequate air flow. See Technical Data, page20, for minimum cfm requirements.

Recommended 5/16 in. (7.9 mm) ID hose, optional 3/8 in. (10 mm) ID air hose.

Set shop air pressure regulator (not supplied) according to paint manufacturer’s recommendation. See maximum compliant air pressure on air cap.

Make sure no air restrictions, such as low-volumecheater-valves,obstruct the air flow. If an air adjusting valve is desired, use a Graco adjustable air valve (234784).

1.Shut off the air supply.

2.Install a shutoff valve (not supplied) downstream of the air regulator to shut off gun air.

3.Install an inline air filter (not supplied) to clean and dry the gun air supply.

4.Connect a clean, dry, filtered air supply to the air inlet fitting. See FIG. 1.

5.Connect the fluid supply to the fluid inlet fitting.

fluid inlet

air inlet

ti11306A

FIG. 1

Ground the Gun

Check your local electrical code for detailed grounding instructions.

Ground the gun through connection to a Graco-approvedconductive air supply hose.

Flush Before Using Equipment

The equipment was tested with lightweight oil, which is left in the fluid passages to protect parts. To avoid contaminating your fluid with oil, flush the equipment with a compatible solvent before using the equipment. See Flush, page9.

6

312579H

Adjust Spray Pattern

1.Rotate the air cap to achieve desired spray pattern. See FIG. 2.

ti4839a

FIG. 2

2.To achieve full fan pattern, open the air control valve by turning the knob fully counterclockwise. See FIG. 3.

3.To create a round pattern, turn the pattern air off by turning the air control valve fully clockwise. See FIG. 3.

4.Trigger gun and adjust gun air pressure.

Refer to Technical Data, page20, for inlet air pressure.

5.To establish the correct fluid flow, turn the fluid control valve counterclockwise until no restriction of the trigger movement is felt, then turn out another half turn.

air control valvefluid control valve

air inlet valve

ti11097a

FIG. 3

Setup

6.To reduce fluid flow, turn the fluid control valve clockwise.

• If the fluid control valve is turned clockwise all the way, the gun will emit only air.

If you cannot achieve the correct fluid flow with the fluid control valve, a different sized nozzle may be necessary. For smaller fluid flow, use the next size smaller nozzle. For a larger fluid flow, use the next size larger nozzle.

7.Spray a test pattern. Evaluate the spray pattern size and atomization.

8.To achieve a narrow spray pattern, turn air control valve clockwise.

9.To improve atomization, reduce the fluid flow rate. Increasing the air pressure can improve atomization but may result in poor Transfer Efficiency (TE) or non-compliantoperation.

312579H

7

Operation

Operation

Pressure Relief Procedure

1.Turn off the gun air supply.

2.Trigger the gun to relieve pressure.

When using the HVLP spray gun, instead of a conventional airspray gun, you may need to use a slightly slower hand movement and make fewer passes with the gun to coat a part.

This is due to the reduced spray velocity produced by lower HVLP air pressures, along with a larger fluid particle size because there is less air to blow off solvents than is produced by conventional airspray. Take care to avoid runs or sags as you spray.

Apply Fluid

CAUTION

Excessive atomizing air pressure can increase over-spray,reduce transfer efficiency, and result in a poor quality finish.

Regulatory agencies in certain states prohibit the operation of a spray gun above 10 psi (69 kPa, 0.7 bar) atomizing air cap pressure.

1.Fill the cup with material. Do not fill past the full markings on cup.

2.Turn on the shop air to the gun. Set atomizing pressure with the gun fully triggered.

3.Adjust the pattern size and shape. See page 7.

4.To achieve the best results when applying fluid:

Keep the gun perpendicular and

6 to 8 inches (150 to 200 mm) from the object being sprayed.

Use smooth, parallel strokes across the surface to be sprayed with 50% overlap.

SeeTroubleshooting, page11, if youexperience an irregular pattern.

Volatile Organic Compounds

(VOC) Regulation

In certain states, spraying solvents that release

VOCs into the atmosphere when cleaning a spray gun is prohibited. To comply with these air quality laws, you must use a cleaning method that prevents the escape of VOC vapors into the atmosphere. See Compliant Cleaning Methods, page10.

Clean air line filters as directed by themanufacturer.

8

312579H

Daily Gun Maintenance

General Tasks

Follow the Pressure Relief Procedure, page 8.

Frequently lubricate the gun moving parts with a drop of non-siliconeoil.

Do not disassemble the spray gun if you are having a spray pattern problem. See

Troubleshooting, page11, for information on how to correct the problem.

Clean the fluid and air line filters daily.

Check for fluid leakage. Tighten fittings or replace equipment as needed.

CAUTION

Solvent left in gun air passages could result in a poor quality paint finish. Do not use any cleaning method that may allow solvent into the gun air passages.

Do not point gun up while cleaning it.

Do not wipe gun with a cloth soaked in solvent; wring out the excess.

Do not immerse the gun in solvent.

Flush

Flush before using the equipment, before changing colors, and when you are done spraying. Use solvent that is compatible with gun wetted parts and with the fluid that will be sprayed.

See Compliant Cleaning Methods,page 10, to comply with air quality laws if applicable.

1.Follow Pressure Relief Procedure, page 8.

Daily Gun Maintenance

2.Dispose of any paint in the cup.

3.Fill the cup with a small amount of solvent.

4.Spray into a grounded metal waste container until the equipment is clean.

5.Follow Pressure Relief Procedure, page 8.

Clean Gun and Cup

CAUTION

Do not submerge gun in solvent. Solvent dissolves lubricant, dries out packings, and clogs air passages.

Do not use metal tools to clean air cap holes as this may scratch them and distort the spray pattern.

Use a compatible solvent.

1.Flush, page 9.

2.Dampen a soft cloth with solvent and wring out the excess. Point the gun down and wipe off the outside of the gun and cup.

3.Make sure cup lid vent hole is clear.

4.Blow dry gun inside and out. Lubricate.

See Compliant Cleaning Methods,page 10, to comply with air quality laws if applicable.

312579H

9

Daily Gun Maintenance

Clean Nozzle and Air Cap

1.Remove air cap (13), trigger gun, remove nozzle (11), and soak both in a compatible cleaning solution.

CAUTION

Trigger the gun whenever you tighten or remove the nozzle. This keeps the needle tip away from the nozzle seating surface and prevents the tip from being damaged.

2.Clean air cap, nozzle, and front of the gun with a soft-bristlebrush dipped into compatible solvent. Do not use a wire brush or metal tools.

3.Use a soft implement, such as a toothpick, to clean out air cap holes.

4.Trigger the gun while you install the fluid nozzle with the gun tool. Tighten the nozzle securely to 155-165in-lb(17.5-18.6N•m) to obtain a good seal.

5.Install the retaining ring (14) and air cap (13).

When reassembling, make sure theair cap matches the color etched onto

the side of the nozzle (gold, brown, grey, blue, etc.).

6.After cleaning the gun, lubricate the following parts with lubricant 111265 daily:

fluid control valve threads

trigger pivot pin

fluid needle shaft

Compliant Cleaning Methods

1.Place spray gun in a gun washer that completely encloses the gun and components during cleaning, rinsing, and draining.

2.Spray solvent through the spray gun into a closed gun cleaning station.

10

312579H

Daily Gun Maintenance

312579H

11

Daily Gun Maintenance

Troubleshooting

Problem

Cause

Solution

 

 

 

Spray Pattern

Normal pattern.

No action necessary.

Right

 

 

Spray Pattern

Dirty or damaged air cap or fluid

Rotate air cap 180°.

 

nozzle.

If pattern follows air cap, problem is in air

 

 

 

 

cap (13). Clean and inspect. If pattern is

 

 

not corrected, replace air cap.

Wrong

 

If pattern does not follow the air cap, the

Heavy top

 

 

problem is with the fluid nozzle. Clean

or bottom

 

 

and inspect the nozzle. If the pattern is

 

 

 

 

not corrected, replace nozzle.

Spray Pattern

Pressure too high for viscosity of

Reduce air pressure and increase mate-

 

material being sprayed.

rial viscosity.

 

 

Correct pattern by narrowing fan size with

Wrong

 

fluid control valve (8).

Split pattern

 

 

Spray Pattern

Dirty or distorted air horn holes.

Clean and inspect air cap. If pattern is not

 

 

corrected, replace air cap.

Wrong

 

 

Gun spitting

Air getting into paint stream.

Check if cup is empty and fill.

 

 

Tighten fluid nozzle (11).

 

 

Check and tighten needle packing nut (17).

 

 

Check fluid nozzle (11) for damage.

 

 

Replace fluid inlet gasket (3)

 

Damaged fluid nozzle seal (19).

Replace seal (19).

Will not spray

Cup is empty.

Fill cup.

 

Fluid control valve (8) turned too

Adjust valve (8) counterclockwise.

 

far clockwise.

 

12

312579H

 

 

Daily Gun Maintenance

 

 

 

Problem

Cause

Solution

 

 

 

Excessive air

Loose fluid nozzle (11).

Tighten fluid nozzle (11).

blowing back

 

 

Damaged fluid nozzle seal (19).

Replace seal (19).

 

 

 

 

Excessive air leak

Worn u-cups/airvalve.

Repair gun (Kit 289408). Be sure to use

behind

 

all included parts.

trigger.

Worn trigger.

Replace trigger (part 289140). If leak per-

 

 

sists repair gun (Kit 289408).

 

 

 

312579H

13

Repair

Repair

Follow Pressure Relief Procedure,page 8.

See Parts, page16, for callout references.

Disassembly

1.Unscrew retaining ring (14) to remove air cap (13b). Check o-rings(13a and 13c) and replace if necessary.

2.Trigger gun while unscrewing nozzle (11) to prevent needle damage.

3.Check o-ring(19) and replace if necessary.

4.Remove fluid control valve (8), spring (26), needle (9), and nut (7). Inspect. Replace tip (9c), needle (9), and u-cupseal (20) as necessary. If replacing needle tip, use low strength thread adhesive on needle tip threads.

5.Remove spring (28) and push the air valve assembly (6) out the back of the gun.

Inspect. Replace air valve assembly (6) and u-cupseal (20) as necessary. Use tool (33) to installu-cupseal.

6.Remove trigger nut (22), trigger pin (21), wave washer (18), and trigger (10).

7.Unscrew needle packing nut (17) and remove u-cuppacking (16) and spreader (15).

8.Remove air control valve assembly (5).

Inspect and replace as necessary.

9.Remove air inlet valve assembly (27).

Inspect and replace as necessary.

Fluid Inlet Fitting Replacement

PRESSURIZED EQUIPMENT HAZARD

Fluid inlet gasket (3) must be replaced if fluid inlet fitting (4) is removed from spray gun.

Failure to replace gasket (3) may result in air leakage into the fluid section causing a non-ventedgravity cup to become pressurized.

1.Remove fluid inlet fitting (4).

2.Remove fluid inlet gasket (3) from gun body and discard.

3.Apply thread sealant to replacement fluid inlet fitting (4) threads.

4.Snap the fluid inlet gasket (3) securely onto the fluid inlet fitting (4).

5.Screw in fluid inlet fitting (4) and torque to 155-165in.-lb(17.5-18.6N•m).

6.Replace washer (28) as required.

14

312579H

Reassembly

1.Install air control valve assembly (5) with valve turned fully counterclockwise to outermost position. Torque to 85-90in-lb(9.6-10.2N•m).

2.Install air inlet valve assembly (27) with valve turned fully counterclockwise to outermost position. Torque to 205-215in-lb

(23.2-24.3N•m).

3.Lubricate u-cupspreader (15) andu-cuppacking (16). Install spreader (15) with tapered end facing rear of gun. Installu-cuppacking (16) with open end facing front of gun. Install packing nut (17). Torque to

3 in-lb(0.3 N•m).

Repair

4.Install wave washer (18) with cupped side toward the gun body. Lubricate and apply thread retainer to trigger pin (10). Install trigger (10), trigger pin (21), and trigger

nut (22). Torque to 15-20in-lb

(1.7-2.2N•m).

5.Install air valve assembly (6), spring (28), and nut (7). Torque to 175-185in-lb

(19.8-20.9N•m).

6.Install needle (9) and spring (26). Lightly lubricate and install fluid control valve (8).

7.Trigger gun while replacing nozzle (11).

Torque to 155-165in-lb(17.5-18.6N•m).

8.Install air cap assembly (13) and retaining ring (14).

17 16 15 ti11226a

312579H

15

Parts

Parts

8 3

7 8

20 3

28 3

5 6

10

6

3 26

9a

9b

4 9c

3 4 7 22

1

12 17 2 316

11 23

11 10 27

1Pull trigger before installing nozzle (11).

2Insert spreader (15) with tapered end facing rear of gun. Insert u-cup(16) with open end facing front of gun.

3Apply lubricant.

4Apply low strength thread retainer.

5Apply thread sealant.

6Torque to 85-90in-lb(9.6-10.2N•m).

7Torque to 15-20in-lb(1.7-2.2N•m).

8Torque to 175-185in-lb(19.8-20.9N•m).

9Torque to 155-165in-lb(17.5-18.6N•m).

10Install with valve assembly turned fully counterclockwise to outermost position.

11Torque to 205-215in-lb(23.2-24.3N•m).

12Torque to 3 in-lb(0.3 N•m).

37 45 9

20 3

3

18 3

213

19

11 9 1

13b

13c

15 2

3

 

10

13a

14

 

 

36 11

 

 

ti11224a

16

312579H

Ref.

Part No.

Description

Qty.

1

---

BODY, gun

1

3 †

---

GASKET, fluid inlet

1

4

289792

FITTING, fluid inlet,

1

 

 

includes gasket

 

 

 

(item 3)

 

5

289796

VALVE, air control

1

 

 

assembly

 

6*

289039

VALVE, air, assembly

1

7*

289052

NUT, air valve, u-cup

1

 

 

assembly

 

8

289097

VALVE, fluid control

1

9

See p. 19 NEEDLE, assembly

1

9a

---

NUT, needle

1

9b

---

NEEDLE

1

9c

See p. 19

TIP, needle

1

10

289140

TRIGGER

1

11

See p. 19

NOZZLE, fluid

1

13

See p. 19

AIR CAP, assembly

1

 

 

(includes 13a-13c)

 

13a

---

WASHER

1

13b

---

O-RING

1

13c

See p. 19 AIR CAP

1

14

---

RING, retaining

1

15 +

---

SPREADER, u-cup

1

16 +

---

PACKING, u-cup

1

17

289793

NUT

1

18

---

WASHER, wave

1

19

111457

O-RING

1

20*

---

PACKING, u-cup

1

21

---

PIN, pivot

1

22

---

NUT, pivot pin

1

23

289451

FITTING, air inlet

1

26•

---

SPRING, compression

1

 

 

Parts

Ref.

Part No. Description

Qty.

27

289142

VALVE, assembly,

1

 

 

air inlet

 

28*

---

SPRING, compression

1

29

289794

TOOL, gun

1

33*

---

TOOL, installation,

1

 

 

seal

 

36

289452

NUT, air plug,

1

 

 

not assembled

 

37

---

WASHER, uhmw

1

38

289770

CUP, gravity, 650 cc

1

38a

289195

FILTER, cup

 

 

 

(not shown)

 

Included in Gun Repair Kit 289790.

Included in Trigger Repair Kit 289143

(contains 5 of each part).

+ Included in Needle Packing Repair Kit

289455 (contains 5 of each part).

* Included in Air Valve Repair Kit 289408.

Included in Air Cap Seal Kit 289791

(contains 5 of each part).

Included in Retaining Ring Kit 289079.

Included in Cup Gasket Repair Kit 289213 (pack of 10).

Included in Gun Body Kit 289022.

† Included in Fluid Inlet Gasket Kit 24A560, package of 5 (purchase separately).

---Not sold separately.

312579H

17

Accessories

Accessories

Cups

Part No. Description

289797 Cup, aluminum, 23 oz (650 cc)

289802 Cup, aluminum, 34 oz (1 liter)

289770 Cup, plastic, 23 oz (650 cc)

192407 Cup Holder

Repair Kits

Part No. Description

289455 Needle Packing Repair Kit

289790 Gun Repair Kit

289791 Air Cap Seal Kit

289143 Trigger Repair Kit

289408 Air Valve Repair Kit

289213 Cup Gasket Kit, 10 pack

289079 Retaining Ring Kit

289022 Gun Handle Replacement Kit

24A560 Fluid Inlet Gasket Kit, 5 pack

24C310 Nozzle O-RingKit,5-pack

Air Valves

Part No. Description

234784 Air Control Valve with Gauge

235119 Gun Air Regulator Assembly

239655 Swivel Air Valve

Cleaning Kit

Part No. Description

105749 Cleaning Brush

111265 Gun Lubricant

15C161 Ultimate Gun Cleaning Kit

3MPPSCups and Accessories

Part No. Description

234941 Cup and Collar, 6 oz, 8-pack

234771 Cup and Collar 25 oz, 8-pack

234937 Cup and Collar 32oz, 4-pack

234940 Lid and Liner, 6 oz, 50-pack

234772 Lid and Liner, 25 oz, 50-pack

234938 Lid and Liner, 32 oz, 25-pack

234942 Ratio Film, insert, 6 oz, 50-pack

15F531 Ratio Film, insert, 25 oz, 100-pack

234939 Ratio Film, insert, 32 oz, 100-pack

289486 Gravity Cup Assembly, 25 oz, includes cup, collar, lid, liner, and adapter

289795 Gravity Feed Adapter

15E470 Lid Dispenser

15E469 Liner Dispenser

15E467 Gun Tray

Test Gauge

Part No. Description

289803 HVLP Verification

Hoses

Part No. Description

239631 4 ft Air Whip Hose Assembly (5/16 in.)

239636 15 ft Air Hose Assembly (5/16 in.)

239637 25 ft Air Hose Assembly (5/16 in.)

Tips

Part No. Description

24E484 .030 SST Needle Tips (Pack of 5)

18

312579H

Repair Kits

Repair Kits

Without Gravity Cup

 

 

Nozzle

Air Cap

Nozzle

Needle

Needle/

Needle Tip

 

 

Size

Kit

Kit

Assembly Kit

Nozzle Kit

Kit

Model

Spray Type

in. (mm)

(13a-13c)

(11, 19)

(9a-9c)

(9a-9c,11, 19)

(9c, 5-pack)

 

 

 

 

 

 

 

 

289002

Conventional

0.055 (1.4)

289773

289780

289799

289493

288185

 

 

 

 

 

 

 

 

289003

Conventional

0.070 (1.8)

289773

289767

289786

289494

289001

 

 

 

 

 

 

 

 

289005

HVLP

0.055 (1.4)

289771

289776

289786

289495

289001

289006

HVLP

0.070 (1.8)

289771

289801

289786

289496

289001

289008

Compliant

0.055 (1.4)

289772

289779

289799

289497

288185

 

 

 

 

 

 

 

 

289009

Compliant

0.070 (1.8)

289772

289559

289799

289498

288185

 

 

 

 

 

 

 

 

With Gravity Cup

 

 

 

 

Nozzle

Needle

Needle/ Nozzle

 

 

 

Nozzle Size

Air Cap Kit

Kit

Assembly Kit

Kits

Needle Tip Kit

Model

Spray Type

in. (mm)

(13a-13c)

(11, 19)

(9a-9c)

(9a-9c,11, 19)

(9c, 5-pack))

 

 

 

 

 

 

 

 

289011

Conventional

0.055 (1.4)

289773

289780

289799

289493

288185

 

 

 

 

 

 

 

 

289012

Conventional

0.070 (1.8)

289773

289767

289786

289494

289001

 

 

 

 

 

 

 

 

289014

HVLP

0.055 (1.4)

289771

289776

289786

289495

289001

289015

HVLP

0.070 (1.8)

289771

289801

289786

289496

289001

289017

Compliant

0.055 (1.4)

289772

289779

289799

289497

288185

 

 

 

 

 

 

 

 

289018

Compliant

0.070 (1.8)

289772

289559

289799

289498

288185

 

 

 

 

 

 

 

 

With 3M PPS Cup

 

 

 

 

Nozzle

Needle

Needle/ Nozzle

 

 

 

Nozzle Size

Air Cap Kit

Kit

Assembly Kit

Kits

Needle Tip Kit

Model

Spray Type

in. (mm)

(13a-13c)

(11, 19)

(9a-9c)

(9a-9c,11, 19)

(9c, 5-pack))

 

 

 

 

 

 

 

 

289020

Conventional

0.055 (1.4)

289773

289780

289799

289493

288185

 

 

 

 

 

 

 

 

289021

Conventional

0.070 (1.8)

289773

289767

289786

289494

289001

 

 

 

 

 

 

 

 

289023

HVLP

0.055 (1.4)

289771

289776

289786

289495

289001

289024

HVLP

0.070 (1.8)

289771

289801

289786

289496

289001

289026

Compliant

0.055 (1.4)

289772

289779

289799

289497

288185

 

 

 

 

 

 

 

 

289027

Compliant

0.070 (1.8)

289772

289559

289799

289498

288185

 

 

 

 

 

 

 

 

Needle Tips

Grooves

 

 

Needle Tip Kit

Grooves

(5-pack)

4

288185

7

289001

ti14043a

312579H

19

Technical Data

Technical Data

Maximum Air Inlet Pressure . . . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar)

Maximum HVLP/Compliant Inbound Air Pressure:

HVLP gravity feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 psi (0.2 MPa, 2.0 bar)* Compliant gravity feed. . . . . . . . . . . . . . . . . . . . . . . . . . 35 psi (0.24 MPa, 2.4 bar)*

Air Consumption:

Conventional Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 CFM at 43 psi (0.3 MPa, 3.0 bar) HVLP Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4 CFM at 29 psi (0.2 MPa, 2.0 bar)

Compliant Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 CFM at 35 psi (0.24 MPa, 2.4 bar)

Fluid and Air Operating Temperature Range 32°F to 109°F (0°C to 43°C)

Spray Gun:

Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 npsm (R1/4-19)

Weight with cup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 lbs (0.6 kg)

Sound Data:

Conventional

Sound pressure at 43 psi (0.3 MPa, 3.0 bar). . . . . . . . 79.52 dB(A)**

Sound power at 43 psi (0.3 MPa, 3.0 bar). . . . . . . . . . 88.05 dB(A)**

HVLP

Sound pressure at 29 psi (0.2 MPa, 2.0 bar). . . . . . . . 83.9 dB(A)**

Sound power at 29 psi (0.2 MPa, 2.0 bar). . . . . . . . . . 90.8 dB(A)**

Compliant

Sound pressure at 35 psi (0.24 MPa, 2.4 bar). . . . . . . 81.8 dB(A)**

Sound power at 35 psi (0.24 MPa, 2.4 bar). . . . . . . . . 88.7 dB(A)**

Gravity Cup Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 oz (0.68 liter) cup

Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 stainless steel, 17-4 PH stainless steel, PEEK, acetal, UHMWPE

*Produces 10 psi (0.07 MPa, 0.7 bar) spraying pressure at air cap.

**All readings were taken with the fan valve fully open (fan full size) at the assumed operator position. Sound power was tested per ISO 9614-2.

20

312579H

Technical Data

312579H

21

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Gracocomponent parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.Phone: 612-623-6921or Toll Free: 1-800-328-0211Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 312579

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

Copyright 2007, Graco Inc. is registered to ISO 9001

www.graco.com

Revised 07/2010