Graco Inc AirPro 312414J, AirPro 312414 User Manual

Size:
1.33 Mb
Download

Instructions-Parts

AirProPressure

Feed Airspray Gun

312414J

ENG

Conventional, HVLP, and compliant guns for specialty industrial applications. For professional use only.

100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure

300 psi (2.1 MPa, 21 bar) Maximum Fluid Inlet Pressure

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

See page 3 for model information.

ti11094a

ll 2 G

Related Manuals

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

General Metal Spray Guns . . . . . . . . . . . . . . . . . 3 General Metal with Stainless Steel Tip . . . . . . . . 3 Automotive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Stain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Waterborne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 High Wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Adhesives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Spatter Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Air Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Gun Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Conventional Guns . . . . . . . . . . . . . . . . . . . . . . . 6 HVLP Guns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Compliant Guns . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connect Air and Fluid Lines . . . . . . . . . . . . . . . . 7 Ground the Gun . . . . . . . . . . . . . . . . . . . . . . . . . 7 Flush Before Using Equipment . . . . . . . . . . . . . . 7 Adjust Spray Pattern . . . . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pressure Relief Procedure . . . . . . . . . . . . . . . . . 9

Apply Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Volatile Organic Compounds (VOC) Regulation . 9

Daily Gun Maintenance . . . . . . . . . . . . . . . . . . . . . 10

General Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Clean Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Compliant Cleaning Methods . . . . . . . . . . . . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Repair Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 24

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 24

Related Manuals

Manual

Language

 

 

313059

Chinese

 

 

313061

Dutch

 

 

313062

Finnish

 

 

313063

French

 

 

313064

German

 

 

313066

Italian

 

 

313067

Japanese

 

 

313068

Korean

 

 

313070

Portuguese

 

 

313071

Russian

 

 

313072

Spanish

 

 

313073

Swedish

 

 

2

312414J

Models

Models

 

 

Conventional

 

HVLP

 

Compliant

 

 

 

 

 

 

 

 

 

 

 

 

 

Max.

 

 

Max.

 

 

Max.

Orifice

 

 

HVLP/Compliant

 

 

HVLP/Compliant

 

 

HVLP/Compliant

Size

 

 

Air Pressure

 

 

Air Pressure

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

 

 

 

 

 

 

 

 

 

 

General

Metal Spray Guns

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.020 (0.5)

288726

A

N/A

288935

A

19 (0.13, 1.3)

288942

A

29 (0.2, 2.0)

0.030 (0.8)

288929

A

N/A

288936

A

19 (0.13, 1.3)

288943

A

29 (0.2, 2.0)

0.042 (1.1)

288930

A

N/A

288937

A

19 (0.13, 1.3)

288944

A

29 (0.2, 2.0)

0.055 (1.4)

288931

A

N/A

288938

A

19 (0.13, 1.3)

288945

A

29 (0.2, 2.0)

0.070 (1.8)

288932

A

N/A

288939

A

19 (0.13, 1.3)

288946

A

29 (0.2, 2.0)

0.086 (2.2)

288933

A

N/A

288940

A

19 (0.13, 1.3)

288947

A

29 (0.2, 2.0)

0.110 (2.8)

288934

A

N/A

288941

A

19 (0.13, 1.3)

288948

A

29 (0.2, 2.0)

General

Metal with Stainless Steel Tip

 

 

 

 

 

 

 

 

 

 

 

 

 

0.042 (1.1)

288949

A

N/A

288952

A

19 (0.13, 1.3)

288955

A

29 (0.2, 2.0)

0.055 (1.4)

288950

A

N/A

288953

A

19 (0.13, 1.3)

288956

A

29 (0.2, 2.0)

0.070 (1.8)

288951

A

N/A

288954

A

19 (0.13, 1.3)

288957

A

29 (0.2, 2.0)

Automotive

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.030 (0.8)

288929

A

N/A

--

--

--

--

--

--

0.040 (1.0)

--

--

--

289034

A

29 (0.2, 2.0)

289036

A

35 (0.24, 2.4)

0.042 (1.1)

288930

A

N/A

--

--

--

--

--

--

0.042 (1.1)

24D472*

A

N/A

--

--

--

--

--

--

0.047 (1.2)

--

--

--

289035

A

29 (0.2, 2.0)

289037

A

35 (0.24, 2.4)

0.055 (1.4)

288931

A

N/A

289541

A

29 (0.2, 2.0)

289542

A

35 (0.24, 2.4)

 

 

 

 

 

 

 

 

 

 

* High production

312414J

3

Models

 

 

Conventional

 

HVLP

 

Compliant

 

 

 

 

 

 

 

 

 

 

 

 

 

Max.

 

 

Max.

 

 

Max.

Orifice

 

 

HVLP/Compliant

 

 

HVLP/Compliant

 

 

HVLP/Compliant

Size

 

 

Air Pressure

 

 

Air Pressure

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

Model

Series

psi (MPa, bar)

 

 

 

 

 

 

 

 

 

 

Stain

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.020 (0.5)

288958

A

N/A

288960

A

22 (0.15, 1.5)

288962

A

29 (0.2, 2.0)

0.030 (0.8)

288959

A

N/A

288961

A

22 (0.15, 1.5)

288963

A

29 (0.2, 2.0)

0.040 (1.0)

289109

A

N/A

289110

A

22 (0.15, 1.5)

289111

A

29 (0.2, 2.0)

Waterborne

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.030 (0.8)

288964

A

N/A

288967

A

23 (0.16, 1.6)

288970

A

23 (0.16, 1.6)

0.042 (1.1)

288965

A

N/A

288968

A

23 (0.16, 1.6)

288971

A

23 (0.16, 1.6)

0.055 (1.4)

288966

A

N/A

288969

A

23 (0.16, 1.6)

288972

A

23 (0.16, 1.6)

High Wear

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.059 (1.5)

288973

A

N/A

288976

A

20 (0.14, 1.4)

288979

A

29 (0.2, 2.0)

0.070 (1.8)

288974

A

N/A

288977

A

20 (0.14, 1.4)

288980

A

29 (0.2, 2.0)

0.086 (2.2)

288975

A

N/A

288978

A

20 (0.14, 1.4)

288981

A

29 (0.2, 2.0)

0.110 (2.8)

289982

A

N/A

289983

A

20 (0.14, 1.4)

289984

A

29 (0.2, 2.0)

 

 

 

 

 

 

 

 

 

 

Adhesives

 

 

Conventional

 

 

 

 

 

 

 

Max.

 

 

 

HVLP/Compliant

Orifice Size

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

 

 

 

 

0.051 (1.3)

288982

A

N/A

0.070 (1.8)

288983

A

N/A

 

 

 

 

Air Brush

 

 

Conventional

 

 

 

 

 

 

 

Max.

 

 

 

HVLP/Compliant

Orifice Size

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

 

 

 

 

0.042 (1.1)

24F202

A

N/A

 

 

 

 

Spatter Gun

 

 

HVLP

 

 

 

 

 

 

 

Max.

 

 

 

HVLP/Compliant

Orifice Size

 

 

Air Pressure

in. (mm)

Model

Series

psi (MPa, bar)

 

 

 

 

0.042 (1.1)

288985

A

30 (0.21, 2.1)

 

 

 

 

4

312414J

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specificrisk. Refer back to these warnings. Additional,product-specificwarnings may be found throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

Keep work area free of debris, including solvent, rags and gasoline.

Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

Ground all equipment in the work area. See Grounding instructions.

If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

Keep a working fire extinguisher in the work area.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer.

Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

Do not alter or modify equipment.

Use equipment only for its intended purpose. Call your distributor for information.

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

Do not kink or over bend hoses or use hoses to pull equipment.

Keep children and animals away from work area.

Comply with all applicable safety regulations.

312414J

5

Gun Selection

WARNING

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

Tighten all fluid connections before operating the equipment.

Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

Read MSDS’s to know the specific hazards of the fluids you are using.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

Always wear impervious gloves when spraying or cleaning equipment.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

Protective eyewear

Clothing and respirator as recommended by the fluid and solvent manufacturer

Gloves

Hearing protection

Gun Selection

Conventional Guns

Excellent atomization and high production rates typically with some reduction in transfer efficiency.

HVLP Guns

An HVLP gun is a high transfer efficiency gun which limits the air pressure at the air cap to 10 psi (0.07 MPa, 0.7 bar) maximum. In some areas, an HVLP gun is required for compliance with environmental standards.

Compliant Guns

A compliant gun is a high transfer efficiency gun which has been tested to have a transfer efficiency greater than or equal to HVLP guns.

The Graco compliant guns have no restrictions on air cap pressures, but the gun inlet pressure must remain under the maximum compliant pressure shown on pages 3-4 to remain in compliance.

6

312414J

Setup

Setup

At least one hose must provide a static ground to the gun.

Connect Air and Fluid Lines

1.Shut off the air supply.

2.Install a shutoff valve (not supplied) downstream of the air regulator to shut off gun air.

3.Install an inline air filter (not supplied) to clean and dry the gun air supply.

4.Connect a clean, dry, filtered air supply to the air inlet fitting. See FIG. 1.

• Recommended 5/16 in. (7.9 mm) ID hose, optional 3/8 in. (9.5 mm) ID hose.

Check that your shop air provides adequate air flow. See Technical Data, page23, for minimum cfm requirements.

Set shop air pressure regulator (not supplied) according to fluid manufacturer’s recommendation. See maximum compliant air pressure on air cap.

Make sure no air restrictions, such as low-volumecheater valves, obstruct the air flow.

5.Connect a fluid hose to the fluid inlet fitting. See FIG. 1.

 

air inlet

fluid inlet

 

 

FIG. 1

 

ti11094a

 

 

 

6.Connect other end of the fluid hose to a regulated fluid supply line.

Ground the Gun

Check your local electrical code and pump manual for detailed grounding instructions.

Ground the spray gun through connection to a Graco-approvedgrounded fluid or air supply hose.

Flush Before Using Equipment

The equipment was tested with lightweight oil, which is left in the fluid passages to protect parts. To avoid contaminating your fluid with oil, flush the equipment with a compatible solvent before using the equipment. See Flush, page10.

312414J

7

Setup

Adjust Spray Pattern

1.Rotate the air cap to achieve desired spray pattern. See FIG. 2.

ti4839a

FIG. 2

2.To achieve full fan pattern, open the air control valve by turning the knob fully counterclockwise. See FIG. 3.

3.To create a round pattern, turn the pattern air off by turning the air control valve fully clockwise. See FIG. 3.

4.Trigger gun and adjust gun air pressure.

Refer to Technical Data, page23, for inlet air pressure recommendations.

5.To establish the correct fluid flow, turn the fluid control valve counterclockwise until no restriction of the trigger movement is felt, then turn out another half turn.

7.To reduce fluid flow, turn the fluid control valve clockwise.

• If the fluid control valve is turned clockwise all the way, the gun will emit only air.

If you cannot achieve the correct fluid flow with the fluid control valve, a different sized nozzle may be necessary. For smaller fluid flow, use the next size smaller nozzle. For a larger fluid flow, use the next size larger nozzle.

8.Spray a test pattern. Evaluate the spray pattern size and atomization.

9.To achieve a narrow spray pattern, turn air control valve clockwise.

10.To improve atomization, reduce the fluid flow rate. Increasing the air pressure can improve atomization but may result in poor Transfer Efficiency (TE) or non-compliantoperation.

air control valve

fluid control valve

air inlet valve

ti11097a

FIG. 3

6.Adjust fluid pressure to achieve desired fluid flow rate.

8

312414J

Operation

Pressure Relief Procedure

Trapped air can cause the pump to cycle unexpectedly, which could result in serious injury from splashing or moving parts.

1.Turn off air and fluid supply.

2.Hold a metal part of the gun firmly to a grounded metal pail. Trigger the gun to relieve pressure.

Apply Fluid

CAUTION

Excessive atomizing air pressure can increase overspray, reduce transfer efficiency, and result in a poor quality finish.

Regulatory agencies in some states prohibit the operation of a spray gun above 10 psi

(69 kPa, 0.7 bar) atomizing air cap pressure.

1.Turn on shop air and fluid supply to the gun. Set atomizing pressure and fluid pressure with the gun fully triggered.

2.Adjust the pattern size and shape. See page 8.

3.To achieve the best results when applying fluid:

Keep the gun perpendicular and

6 to 8 inches (150 to 200 mm) from object being sprayed.

Use smooth, parallel strokes across the surface to be sprayed with 50% overlap.

Operation

NOTE: See Troubleshooting, page12, ifyou experience an irregular pattern.

When using the HVLP spray gun, instead of a conventional airspray gun, you may need to use a slightly slower hand movement and make fewer passes with the gun to coat a part. This is due to the reduced spray velocity produced by lower HVLP air pressures, along with a larger fluid particle size because there is less air to blow off solvents than is produced by conventional airspray. Take care to avoid runs or sags as you spray.

Volatile Organic Compounds

(VOC) Regulation

In certain states, spraying solvents that release VOCs into the atmosphere when cleaning a spray gun is prohibited. To comply with these air quality laws, you must use a cleaning method that prevents the escape of VOC vapors into the atmosphere. See Compliant Cleaning Methods, page11.

312414J

9

Daily Gun Maintenance

Daily Gun Maintenance

Follow Pressure Relief Procedure, page 9, when you stop spraying and before cleaning, checking, servicing, or transporting equipment. Read Warnings, page 5.

General Tasks

Frequently lubricate the gun moving parts with a drop of non-siliconeoil.

Do not disassemble the spray gun if you are having a spray pattern problem. See

Troubleshooting, page12, for information on how to correct the problem.

Follow the Pressure Relief Procedure,page 9.

Clean the fluid and air line filters daily.

Check for any fluid leakage from gun and fluid hoses.

CAUTION

Solvent left in gun air passages could result in a poor quality paint finish. Do not use any cleaning method that may allow solvent into the gun air passages.

Do not point gun up while cleaning it.

Do not wipe gun with a cloth soaked in solvent; wring out the excess.

Do not immerse the gun in solvent.

Flush

Flush before changing colors, before fluid can dry in the equipment, at the end of the day, before storing, and before repairing equipment. Flush at the lowest pressure possible. Check connectors for leaks and tighten as necessary. Flush with a fluid that is compatible with the fluid being dispensed and the equipment wetted parts.

NOTE: See Compliant Cleaning Methods,page11, to comply with air quality laws if applicable.

1.Follow Pressure Relief Procedure, page 9.

2.Disconnect the fluid supply hose and air supply hose from gun.

3.Connect the solvent supply hose to the gun.

4.Start the pump. Always use the lowest possible fluid pressure when flushing.

5.Hold a metal part of the gun firmly to a grounded metal pail. Trigger the gun until clean solvent dispenses.

6.Turn off solvent supply.

7.Follow Pressure Relief Procedure, page 9,

8.Disconnect the solvent supply hose from the gun.

10

312414J

Clean Gun

CAUTION

Do not submerge gun in solvent. Solvent dissolves lubricant, dries out packings, and clogs air passages.

Do not use metal tools to clean air cap holes as this may scratch them and distort the spray pattern.

Use a compatible solvent.

1.Flush, page 10.

2.Remove air cap. Trigger gun, remove nozzle, and soak both in a compatible solution.

CAUTION

Trigger the gun whenever you tighten or remove the nozzle. This keeps the needle tip away from the nozzle seating surface and prevents the tip from being damaged.

3.Dip the end of a soft-bristlebrush into a compatible solvent. Do not continuously soak the brush's bristles with solvent and do not use a wire brush.

4.With the gun pointed down, clean the front of the gun, using a soft-bristlebrush and solvent.

5.Scrub the air cap retaining ring, air cap, and fluid nozzle with the soft-bristlebrush.

• To clean out air cap holes, use a soft implement, such as a toothpick, to avoid damaging critical surfaces.

Clean the air cap and fluid nozzle daily, minimum. Some applications require more frequent cleaning.

Do not soak the air cap retaining ring in solvent for prolonged periods of time.

Daily Gun Maintenance

6.Trigger the gun while you install the fluid nozzle with the gun tool. Tighten the nozzle securely to 155-165in-lb(17.5-18.6N•m) to obtain a good seal.

7.Install the retaining ring (14) and air cap (13b).

8.Dampen a soft cloth with solvent and wring out the excess. Point the gun down and wipe off the outside of the gun.

9.After cleaning the gun, lubricate the following parts with lubricant 111265 daily:

fluid control valve threads

trigger pivot pin

fluid needle shaft

Compliant Cleaning Methods

1.Place spray gun in a gun washer that completely encloses gun and components during cleaning, rinsing, and draining.

2.Spray solvent through the spray gun into a closed gun cleaning station.

312414J

11

Troubleshooting

Troubleshooting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Problem

 

 

 

Cause

Solution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spray Pattern

 

Normal pattern.

No action necessary.

Right

 

 

Spray Pattern

Dirty or damaged air cap or

Rotate air cap (13) 180°.

 

fluid nozzle.

If pattern follows air cap, prob-

 

 

 

 

lem is in air cap. Clean and

 

 

inspect. If pattern is not cor-

 

 

rected, replace air cap.

Wrong

 

If pattern does not follow the air

Heavy top

 

or bottom

 

cap, the problem is with the

 

 

fluid nozzle (11). Clean and

 

 

inspect the nozzle. If the pat-

 

 

tern is not corrected, replace

 

 

nozzle.

Spray Pattern

Pressure too high for viscosity

Reduce air pressure and

 

of material being sprayed.

increase material viscosity.

 

 

Correct pattern by narrowing

 

 

fan size with the fluid control

Wrong

 

valve (8).

Split pattern

 

 

Spray Pattern

Dirty or distorted air horn

Clean and inspect air cap (13).

 

holes.

If pattern is not corrected,

 

 

replace air cap.

Wrong

 

 

12

312414J

 

 

Troubleshooting

 

 

 

Problem

Cause

Solution

 

 

 

 

 

 

Gun spitting.

Air getting into paint stream.

Check if fluid source is empty

 

 

and fill.

 

 

Tighten fluid nozzle (11).

 

 

Check and tighten needle

 

 

packing nut (9a).

 

 

Check fluid nozzle (11) for

 

 

damage.

 

 

 

Will not spray.

Fluid control valve (8) turned

Adjust fluid control valve (8)

 

too far clockwise.

counterclockwise.

 

 

 

 

Fluid source empty.

Refill.

 

 

 

Excessive air blowing back.

Loose fluid nozzle (11).

Tighten fluid nozzle (11).

 

 

 

 

Damaged fluid nozzle seal

Replace seal (19).

 

(19).

 

 

 

 

Excessive air leak behind

Worn u-cups/airvalve.

Repair gun (Kit 289407). Be

trigger.

 

sure to use all included parts.

 

 

 

 

Worn trigger.

Replace trigger (part 289140).

 

 

If leak persists repair gun (Kit

 

 

289407).

 

 

 

Gun fluid pressure is too high

Using needle/nozzle kit with

Use needle/nozzle kit with

with gun triggered (cannot

too small orifice.

larger orifice.

achieve desired flow rate).

 

 

 

 

 

Using a low fluid pressure set-

Using needle/nozzle kit with

Use needle/nozzle kit with

ting, the fluid flow is too high,

too large orifice.

smaller orifice.

making it necessary to restrict

 

 

needle travel to reduce fluid

 

 

flow.

 

 

 

 

 

Fluid system will not operate at

There is no fluid regulator, or

Add low pressure fluid regula-

low enough pressure [below

air regulator is not sensitive

tor, or add more sensitive low

10 psi (70 kPa, 0.7 bar)].

enough at low pressure.

pressure air regulator.

 

 

 

Fluid flow is fluttering while

Fluid filter clogged.

Check fluid filter.

spraying.

 

 

Fluid source empty.

Refill.

 

 

 

Fluid flow fades while spraying

Air hose size is too restricted

Use 5/16 in. (7.9 mm) I.D. air

high viscosity fluids.

for higher air flow being used.

hose if the hose is 25 ft (7.6 m)

 

 

long. If longer hose is needed,

 

 

use a 3/8 in. (9.5 mm) I.D.

 

 

hose.

 

 

 

312414J

13

Repair

Repair

Follow Pressure Relief Procedure,page 9.

See Parts, page16, for callout references.

Disassembly

1.Unscrew retaining ring (14) to remove air cap (13b). Check o-rings(13a and 13c) and replace if necessary.

2.Trigger gun while unscrewing nozzle (11) to prevent needle damage.

3.Check o-ring(19) and replace if necessary.

4.Remove fluid control valve (8), spring (26), needle (9), and nut (7). Inspect. Replace tip (9c), needle (9), and u-cupseal (20) as necessary. If replacing needle tip, use low strength thread adhesive on needle tip threads.

5.Remove spring (28) and push the air valve assembly (6) out the back of the gun.

Inspect. Replace air valve assembly (6) and u-cupseal (20) as necessary. Use tool (33) to installu-cupseal.

6.Remove trigger nut (22), trigger pin (21), wave washer (18), and trigger (10).

7.Unscrew needle packing nut (17) and remove u-cuppacking (16) and spreader (15).

8.Remove air control valve assembly (5). Inspect and replace as necessary.

9.Remove air inlet valve assembly (27).

Inspect and replace as necessary.

NOTE: Do not remove the fluid inlet fitting.

It was attached to the gun body with permanent thread locker. There is also no need to remove the air inlet fitting.

14

312414J

Reassembly

1.Install air control valve assembly (5) with valve turned fully counterclockwise to outermost position. Torque to 85-90in-lb(9.6-10.2N•m).

2.Install air inlet valve assembly (27) with valve turned fully counterclockwise to outermost position. Torque to 205-215in-lb(23.2-24.3N•m).

3.Lubricate u-cupspreader (15) andu-cuppacking (16). Install spreader (15) with tapered end facing rear of gun. Installu-cuppacking (16) with open end facing front of gun. Install packing nut (17). Torque to

3 in-lb(0.3 N•m).

ti11226a

17 16 15

Repair

4.Install wave washer (18) with cupped side toward the gun body. Lubricate and apply thread retainer to trigger pin (10). Install trigger (10), trigger pin (21), and trigger nut (22). Torque to 15-20in-lb

(1.7-2.3N•m).

5.Install air valve assembly (6), spring (28), and nut (7). Torque to 175-185in-lb

(19.8-20.9N•m).

6.Install needle (9) and spring (26). Lightly lubricate and install fluid control valve (8).

7.Trigger gun while replacing nozzle (11). Torque to 155-165in-lb(17.5-18.6N•m).

8.Install air cap assembly (13) and retaining ring (14).

312414J

15

Parts

Parts

 

8 3

7 8

 

20 3

28 3

5 6

10

6

20 3

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

18 3

 

 

 

 

 

 

 

 

 

 

 

 

 

21 3

4

 

 

 

 

 

 

 

 

 

 

 

 

 

19

 

 

 

 

 

 

 

 

 

 

 

 

 

11 9

1

 

 

 

 

 

 

 

 

 

 

 

 

13b

3

26

 

 

 

 

 

 

 

 

 

 

 

13c

 

 

 

 

 

 

 

 

 

 

 

 

 

9a

 

 

 

 

 

 

 

 

 

 

 

 

 

9b

 

 

 

 

 

 

 

 

 

 

 

 

 

4

9c

7

22

 

 

 

 

 

2

 

 

 

 

3

4

 

 

 

 

 

 

 

 

 

 

 

 

 

12 17

 

 

 

 

 

 

 

 

 

 

 

 

2

3 16

 

 

 

3 11

5

 

 

 

 

 

 

2

3

15

 

 

 

 

 

 

 

 

 

 

 

 

11 23

 

 

 

10

13a

14

 

11

10 27

36 11

ti11194a

1Pull trigger before installing nozzle (11).

2Insert spreader (15) with tapered end facing rear of gun. Insert u-cup(16) with open end facing front of gun.

3Apply lubricant.

4Apply low strength thread retainer.

5Apply high-strengththread retainer.

6Torque to 85-90in-lbs(9.6-10.2N•m).

7Torque to 15-20in-lbs(1.7-2.2N•m).

8Torque to 175-185in-lbs(19.8-20.9N•m).

9Torque to 155-165in-lbs(17.5-18.6N•m).

10Install with valve assembly turned fully counterclockwise to outermost position.

11Torque to 205-215in-lbs(23.2-24.3N•m).

12Torque to 3 in-lbs(0.3 N•m).

16

312414J

Parts

Ref.

Part

Description

Qty.

1

289016

BODY, gun

1

2‡

---

GASKET, fluid inlet

1

3‡

---

FITTING, fluid inlet

1

5

289796

VALVE, air control

1

 

 

assembly

 

6 *

289038

VALVE, air, assembly

1

7*

289052

NUT, air valve, u-cup

1

 

 

assembly

 

8

289097

VALVE, fluid control

1

9

see

NEEDLE, assembly

1

 

p. 20-22

(includes 9a-9c)

 

9a

---

NUT, needle

1

9b

---

NEEDLE

1

9c

see

TIP, needle

1

 

p. 20-22

 

 

10

289140

TRIGGER, gun

1

11

see

NOZZLE, fluid,

1

 

p. 20-22

pressure feed

 

13

see

AIR CAP, assembly

1

 

p. 20-22

(includes 13a-13c)

 

13a

---

WASHER

1

13b

---

O-RING

1

13c

see

AIR CAP

1

 

p. 20-22

 

 

14

---

RING, retaining

1

15 +

---

SPREADER, u-cup

1

16 +

---

PACKING, u-cup

1

17

289793

NUT

1

18

---

WASHER, wave

1

19

111457

PACKING, o-ring

1

20 *

---

PACKING, u-cup,gun

2

21

---

PIN, pivot

1

22

---

PIN, pivot, nut

1

23

289451

FITTING, air inlet

1

26*

---

SPRING, compression 1

27

289142

VALVE, assembly,

1

 

 

air inlet

 

28*

---

SPRING, compression 1

29

289794

TOOL, gun

1

33 *

---

TOOL, installation,

1

 

 

seal

 

36

289452

NUT, air plug

1

 

 

(not assembled)

 

Included in Gun Repair Kit 289399.

Included in Trigger Repair Kit 289143

(contains 5 of each part).

+Included in Needle Packing Repair Kit 289455 (contains 5 of each part).

* Included in Air Valve Repair Kit 289407.

Included in Air Cap Seal Kit 289791

(contains 5 of each part).

Included in Retaining Ring Kit 289079.

Included in Gun Body Kit 289016.

‡ Included in Fluid Inlet Fitting Kit 24C269.

---Not sold separately.

312414J

17

Parts

18

312414J

Accessories

Repair Kits

Part No. Description

289455 Needle Packing Repair Kit

289399 Gun Repair Kit

289791 Air Cap Seal Kit

289143 Trigger Repair Kit

289407 Air Valve Repair Kit

289079 Retaining Ring Kit

24C269 Fluid Inlet Fitting Kit

24C310 Nozzle O-RingKit,5-pack

289016 Gun Body Kit

288986 Gun without needle, nozzle, or air cap, with 3/8 npsm (R3/8-19)fluid inlet

289419 Gun without needle, nozzle, or air cap, with 1/4 npsm (R1/4-19)fluid inlet

Air Valves and Regulators

Part No. Description

234784 Air Control Valve with Gauge

235119 Gun Air Regulator Assembly

239655 Swivel Air Valve

Cups

Part No. Description

239802 1 qt SST Pressure Cup with

Single Air Regulator 239803 1 qt SST Pressure Cup with

Double Air Regulator 239804 1 qt SST Pressure Cup with

Remote Air Regulator 240266 Disposable Polyethylene Cup

Liners (40 pack), for 1 qt siphon and pressure cups only

235117 2 qt Pressure Cup with Regulator and Hose

Cleaning Kits

Part No. Description

105749 Cleaning Brush

111265 Gun Lubricant

15C161 Ultimate Gun Cleaning Kit

Accessories

Test Gauges

Part No. Description

289803 HVLP Automotive Verification

289563 HVLP General Metal 0.5 - 1.8 mm

(0.020-0.070in.) Verification

289564 HVLP General Metal 2.2 mm

(0.086 in.) Verification

289565 HVLP General Metal 2.8 mm

(0.110 in.) Verification

289566 HVLP Stain Verification

289567 HVLP Waterborne Verification

289568 HVLP High Wear 1.5 mm

(0.059 in.) Verification

289569 HVLP High Wear 1.8-2.2mm

(0.070-0.086in.) Verification

Hoses

Part No. Description

239631 4 ft Air Whip Hose Assembly (5/16 in.)

239636 15 ft Air Hose Assembly (5/16 in.)

239637 25 ft Air Hose Assembly (5/16 in.)

239622 4 ft Fluid Whip Hose Assembly

(3/16 in.)

239633 15 ft Fluid Hose Assembly

(3/16 in.)

239634 25 ft Fluid Hose Assembly

(3/16 in.)

312414J

19

Repair Kits

Repair Kits

 

 

 

 

Nozzle

Needle

Needle/

Needle Tip

 

 

Nozzle Size

Air Cap Kit

Kit

Assembly Kit

Nozzle Kit

Kit

Model

Spray Type

in. (mm)

(13a-13c)

(11, 19)

(9a-9c)

(9a-9c,11, 19)

(9c, 5-pack)

 

 

 

 

 

 

 

 

General Metal Spray Guns

288726

Conventional

0.020 (0.5)

289773

289061

289270

289458

289350

288929

Conventional

0.030 (0.8)

289773

289062

289271

289459

288183

288930

Conventional

0.042 (1.1)

289773

289063

289785

289460

288184

288931

Conventional

0.055 (1.4)

289773

289064

289799

289462

288185

288932

Conventional

0.070 (1.8)

289784

289065

289799

289464

288185

288933

Conventional

0.086 (2.2)

289068

289066

289787

289466

289004

288934

Conventional

0.110 (2.8)

289069

289067

289800

289467

289007

288935

HVLP

0.020 (0.5)

289041

289061

289270

289458

289350

288936

HVLP

0.030 (0.8)

289041

289062

289271

289459

288183

288937

HVLP

0.042 (1.1)

289041

289063

289785

289460

288184

288938

HVLP

0.055 (1.4)

289041

289064

289799

289462

288185

288939

HVLP

0.070 (1.8)

289041

289065

289799

289464

288185

288940

HVLP

0.086 (2.2)

289070

289066

289787

289466

289004

288941

HVLP

0.110 (2.8)

289043

289067

289800

289467

289007

288942

Compliant

0.020 (0.5)

289042

289061

289270

289458

289350

288943

Compliant

0.030 (0.8)

289042

289062

289271

289459

288183

288944

Compliant

0.042 (1.1)

289042

289063

289785

289460

288184

288945

Compliant

0.055 (1.4)

289042

289064

289799

289462

288185

288946

Compliant

0.070 (1.8)

289042

289065

289799

289464

288185

288947

Compliant

0.086 (2.2)

289044

289066

289787

289466

289004

288948

Compliant

0.110 (2.8)

289045

289067

289800

289467

289007

General

Metal with

Stainless Steel Tip

 

 

 

 

 

 

 

 

 

 

 

 

288949

Conventional

0.042 (1.1)

289773

289063

289272

289461

289010

288950

Conventional

0.055 (1.4)

289773

289064

289273

289463

289013

288951

Conventional

0.070 (1.8)

289784

289065

289273

289465

289013

288952

HVLP

0.042 (1.1)

289041

289063

289272

289461

289010

288953

HVLP

0.055 (1.4)

289041

289064

289273

289463

289013

288954

HVLP

0.070 (1.8)

289041

289065

289273

289465

289013

288955

Compliant

0.042 (1.1)

289042

289063

289272

289461

289010

288956

Compliant

0.055 (1.4)

289042

289064

289273

289463

289013

288957

Compliant

0.070 (1.8)

289042

289065

289273

289465

289013

20

312414J

 

 

 

 

 

 

 

Repair Kits

 

 

 

 

 

 

 

 

 

 

 

 

 

Nozzle

Needle

Needle/

Needle Tip

 

 

 

Nozzle Size

Air Cap Kit

Kit

Assembly Kit

Nozzle Kit

Kit

 

Model

Spray Type

in. (mm)

(13a-13c)

(11, 19)

(9a-9c)

(9a-9c,11, 19)

(9c, 5-pack)

 

 

 

 

 

 

 

 

 

 

Automotive

 

 

 

 

 

 

 

288929

Conventional

0.030 (0.8)

289773

289062

289271

289459

288183

 

288930

Conventional

0.042 (1.1)

289773

289063

289785

289460

288184

 

24D472*

Conventional

0.042 (1.1)

289040

289063

289785

289460

288184

 

288931

Conventional

0.055 (1.4)

289773

289064

289799

289462

288185

 

289034

HVLP

0.040 (1.0)

289771

289774

289785

289468

288184

 

289035

HVLP

0.047 (1.2)

289771

289775

289799

289469

288185

 

289541

HVLP

0.055 (1.4)

289771

289776

289786

289495

289001

 

289036

Compliant

0.040 (1.0)

289772

289777

289785

289470

288184

 

289037

Compliant

0.047 (1.2)

289772

289778

289799

289471

288185

 

289542

Compliant

0.055 (1.4)

289772

289779

289799

289497

288185

 

* High production

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stain

 

 

 

 

 

 

 

 

288958

Conventional

0.020 (0.5)

288862

288907

289270

289472

289350

 

288959

Conventional

0.030 (0.8)

288862

288927

289271

289473

288183

 

289109

Conventional

0.040 (1.0)

288862

289112

289785

289474

288184

 

288960

HVLP

0.020 (0.5)

288864

288907

289270

289472

289350

 

288961

HVLP

0.030 (0.8)

288864

288927

289271

289473

288183

 

289110

HVLP

0.040 (1.0)

288864

289112

289785

289474

288184

 

288962

Compliant

0.020 (0.5)

288863

288907

289270

289472

289350

 

288963

Compliant

0.030 (0.8)

288863

288927

289271

289473

288183

 

289111

Compliant

0.040 (1.0)

288863

289112

289785

289474

288184

 

Adhesives

 

 

 

 

 

 

 

 

288982

Conventional

0.051 (1.3)

289051

289077

289799

289484

288185

 

288983

Conventional

0.070 (1.8)

289051

289078

289799

289485

288185

 

Spatter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

288985

HVLP

0.042 (1.1)

289053

289063

289785

289460

288184

 

Air Brush

 

 

 

 

 

 

 

24F202

Conventional

0.042 (1.1)

24D705

289063

289785

289460

288184

 

312414J

21

Repair Kits

 

 

 

 

Nozzle

Needle

Needle/

Needle Tip

 

 

Nozzle Size

Air Cap Kit

Kit

Assembly Kit

Nozzle Kit

Kit

Model

Spray Type

in. (mm)

(13a-13c)

(11, 19)

(9a-9c)

(9a-9c,11, 19)

(9c, 5-pack)

 

 

 

 

 

 

 

 

Waterborne

 

 

 

 

 

 

 

288964

 

Conventional

0.030 (0.8)

 

289046

289071

289785

289475

288184

288965

 

Conventional

0.042 (1.1)

 

289046

289072

289785

289476

288184

288966

 

Conventional

0.055 (1.4)

 

289046

289073

289799

289477

288185

288967

 

HVLP

0.030 (0.8)

 

289047

289071

289785

289475

288184

288968

 

HVLP

0.042 (1.1)

 

289047

289072

289785

289476

288184

288969

 

HVLP

0.055 (1.4)

 

289047

289073

289799

289477

288185

288970

 

Compliant

0.030 (0.8)

 

289048

289071

289785

289475

288184

288971

 

Compliant

0.042 (1.1)

 

289048

289072

289785

289476

288184

288972

 

Compliant

0.055 (1.4)

 

289048

289073

289799

289477

288185

High Wear

 

 

 

 

 

 

 

288973

 

Conventional

0.059 (1.5)

 

288861

289074

289352

289478

N/A

288974

 

Conventional

0.070 (1.8)

 

289049

289075

289352

289479

N/A

288975

 

Conventional

0.086 (2.2)

 

289049

289076

289351

289480

N/A

289982

 

Conventional

0.110 (2.8)

 

289049

289975

289979

289980

N/A

288976

 

HVLP

0.059 (1.5)

 

289115

289331

289352

289481

N/A

288977

 

HVLP

0.070 (1.8)

 

289325

289332

289352

289482

N/A

288978

 

HVLP

0.086 (2.2)

 

289325

289333

289351

289483

N/A

289983

 

HVLP

0.110 (2.8)

 

289325

289976

289979

289981

N/A

288979

 

Compliant

0.059 (1.5)

 

289050

289331

289352

289481

N/A

288980

 

Compliant

0.070 (1.8)

 

289327

289332

289352

289482

N/A

288981

 

Compliant

0.086 (2.2)

 

289327

289333

289351

289483

N/A

289984

 

Compliant

0.110 (2.8)

 

289327

289976

289979

289981

N/A

Needle Tips

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Grooves

 

Needle Tip

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

289004, 289007

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

289350

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

288183

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

288184

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

288185

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Grooves

ti14043a

22

312414J

 

Technical Data

Technical Data

 

WW

100 psi (0.7 MPa, 7 bar)

Maximum Air Inlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Fluid Inlet Pressure . . . . . . . . . . . . . . . . . . . . . . .

300 psi (2.1 MPa, 21 bar)

Maximum HVLP*/Compliant Inbound Air Pressure . . . . .

Printed on air cap. See Models, page3-4.

Fluid and Air Operating Temperature Range . . . . . . . . . . . .

32°-109°F(0°-43°C)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

410 g

Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1/4 npsm (R1/4-19)

Fluid Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3/8 npsm (R3/8-19)

Wetted Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

303 stainless steel, 17-4PH stainless steel, PEEK,

 

acetal, UHMWPE

Noise Data**. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 

Conventional

 

Sound power at 43 psi (0.30 MPa, 3.0 bar) . . . . . . . .

88.82 dB(A)**

Sound Power at 43 psi (0.30 MPa, 3.0 bar) . . . . . . . .

78.91 dB(A)**

HVLP

 

Sound power at 19 psi (0.13 MPa, 1.3 bar) . . . . . . . .

89.70 dB(A)**

Sound Power at 19 psi (0.13 MPa, 1.3bar). . . . . . . . .

79.79 dB(A)**

Compliant

 

Sound power at 29 psi (0.20 MPa, 2.0 bar) . . . . . . . .

87.47 dB(A)**

Sound Power at 29 psi (0.20 MPa, 2.0 bar) . . . . . . . .

77.56 dB(A)**

*Produces 10 psi (0.07 MPa, 0.7 bar) spraying pressure at air cap.

**All readings were taken with the fan valve fully open. Sound power was tested to ISO 9614-2.

Air Consumption

 

 

Air Inlet

Air

 

 

Pressure

Consumption

Spray Type

Application

psi (MPa, bar)

(scfm)

Conventional

Stain

35

(0.24, 2.4)

15.2

HVLP

Stain

22

(0.15, 1.5)

14.8

Compliant

Stain

29

(0.2, 2.0)

13.6

Conventional

Adhesive

21

(0.14, 1.4)

11.3

Conventional

General Metal

36

(0.25, 2.5)

12.6

HVLP

General Metal

19

(0.13, 1.3)

14.9

Compliant

General Metal

29

(0.2, 2.0)

11.7

Conventional

High Wear

38

(0.26, 2.6)

17.1

HVLP

High Wear

20

(0.14, 1.4)

15.0

Compliant

High Wear

29

(0.2, 2.0)

10.7

Conventional

Waterborne

36

(0.25, 2.5)

12.6

HVLP

Waterborne

20

(0.14, 1.4)

15.0

Compliant

Waterborne

23

(0.16, 1.6)

13.1

Conventional

Automotive

36

(0.25, 2.5)

12.6

HVLP

Automotive

29

(0.2, 2.0)

14.4

Compliant

Automotive

35

(0.24, 2.4)

11.2

312414J

23

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Gracocomponent parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.Phone: 612-623-6921or Toll Free: 1-800-328-0211Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 312414

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

Copyright 2007, Graco Inc. is registered to ISO 9001

www.graco.com

Revised 07/2010