Graco Inc 235459, 237691, 308235 User Manual

Size:
402.18 Kb
Download

INSTRUCTIONS-PARTSLIST

308–235

This manual contains important

Rev. F

Supersedes Rev. E

warnings and information.

READ AND KEEP FOR REFERENCE.

 

INSTRUCTIONS

 

Flex Airless Spray Gun

5000 psi (345 bar) MAXIMUM WORKING PRESSURE

Model 235–457,Series C

Bare gun.

Model 237–691,Series B

Includes RAC IV DripLess Tip Guard, 517 size

SwitchTip , and 2 finger trigger.

Model 235–459,Series D

Includes RAC IV DripLess Tip Guard, 517 size

 

SwitchTip , and 2 finger trigger.

Model 235–459

Model 235–458,Series C

 

Includes the Standard (non-reversing)DripLess

Tip Guard. Spray tip not included; order separately.

01460

Patents Pending

Model 235–458

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

COPYRIGHT 1992, GRACO INC.

Graco Inc. is registered to I.S. EN ISO 9001

Table of Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . 5 System Requirements . . . . . . . . . . . . . . . . . . . . . . . 5 How to Use the Gun Trigger Safety . . . . . . . . . . . 5 How to Use the Gun . . . . . . . . . . . . . . . . . . . . . . . . 6 How to Adjust the Spray Pattern . . . . . . . . . . . . . . 6

How to Clean the Spray Tip

and Clear a Spray Tip Obstruction . . . . . . . . . . . . 7 How to Check the Gun Diffuser . . . . . . . . . . . . . . . . 8 How to Clean the Filter . . . . . . . . . . . . . . . . . . . . . . . . 6 How to Flush the Gun . . . . . . . . . . . . . . . . . . . . . . . . . 8 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Graco Phone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . 14 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

INSTRUCTIONS

DThis equipment is for professional use only.

DRead all instruction manuals, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

DDo not alter or modify this equipment.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum working pressure of the lowest rated system component. Refer to the Technical Data on page 14 for the maximum working pressure of this equipment.

DUse fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

DDo not use 1,1,1–trichloroethane,methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use could result in a chemical reaction, with the possibility of explosion.

DDo not use hoses to pull equipment.

DRoute hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 66_C (150_F) or below –40_C(–40_F).

DWear hearing protection when operating this equipment.

DDo not lift pressurized equipment.

DComply with all applicable local, state, and national fire, electrical, and safety regulations.

WARNING

INJECTION HAZARD

Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.

D Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medical attention.

DDo not point the gun at anyone or at any part of the body.

DDo not put your hand or fingers over the spray tip.

DDo not stop or deflect leaks with your hand, body, glove or rag.

DDo not “blow back” fluid; this is not an air spray system.

DAlways have the tip guard and the trigger guard on the gun when spraying.

DCheck the gun diffuser operation weekly. See page 8.

DBe sure the gun trigger safety operates before spraying.

DLock the gun trigger safety when you stop spraying.

DFollow the Pressure Relief Procedure on page 5 if the spray tip clogs and before cleaning, checking or servicing the equipment.

DTighten all fluid connections before operating the equipment.

DCheck the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not repair high pressure couplings; you must replace the entire hose.

DFluid hoses must have spring guards on both ends, to help protect them from rupture caused by kinks or bends near the couplings.

MOVING PARTS HAZARD

Moving parts can pinch or amputate your fingers.

DKeep clear of all moving parts when starting or operating the pump.

DBefore servicing the equipment, follow the Pressure Relief Procedure on page 5 to prevent the equipment from starting unexpectedly.

RECOIL HAZARD

Due to the high pressure fluid emitted, a strong recoil action may occur when you trigger this gun. If you are unprepared, your hand could be forced back toward your body or you could lose your balance and fall, resulting in serious injury.

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury.

DIf there is any static sparking or you feel an electric shock while using this equipment, stop spraying immediately. Do not use the equipment until you identify and correct the problem.

DProvide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed.

DKeep the spray area free of debris, including solvent, rags, and gasoline.

DElectrically disconnect all equipment in the spray area.

DExtinguish all open flames or pilot lights in the spray area.

DDo not smoke in the spray area.

DDo not turn on or off any light switch in the spray area while operating or if fumes are present.

DDo not operate a gasoline engine in the spray area.

DGround the equipment and the object being sprayed. Refer to your pump instruction manual.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.

DKnow the specific hazards of the fluid you are using.

DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.

DAlways wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer.

48 5

Installation/Operation

Pressure Relief Procedure

WARNING

INJECTION HAZARD

The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. Fluid

under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you:

Dare instructed to relieve the pressure,

Dstop spraying,

Dcheck or service any of the system equipment,

Dor install or clean the spray tips.

1.Lock the gun trigger safety.

2.Shut off the power supply to the pump. Close any bleed-typemaster air valves.

3.Unlock the gun trigger safety.

4.Hold a metal part of the gun firmly to the side of a grounded metal pail, and trigger the gun to relieve pressure.

5.Lock the gun trigger safety.

6.Open the drain valve (required in your system), having a container ready to catch the drainage.

7.Leave the drain valve open until you are ready to spray again.

If you suspect that the spray tip or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, very slowly loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually, then loosen completely. Now clear the tip or hose.

System Requirements

WARNING

Keep the wallet-sizedwarning card provided with this gun with the operator at all times. The card contains important treatment information should an injection injury occur. Additional cards are available at no charge from Graco Inc.

WARNING

Be sure your system has a bleed-typemaster air valve (pneumatic pumps only) and a pressure drain valve. These accessories help reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, if you are adjusting or repairing the pump or gun.

1.The bleed-type master air valve (air-poweredpumps only) relieves air trapped between this valve and the pump after the air regulator is shut off. Trapped air can cause the pump to cycle unexpectedly.

2.The pressure drain valve assists in relieving fluid pressure in the displacement pump, hose and gun: triggering the gun to relieve pressure may not be sufficient.

3.Strain the fluid you are spraying if it contains particles which could clog the spray tip.

How to Use the Gun Trigger Safety

1.To lock the gun trigger safety, turn the latch (A) to a right angle with the gun body. See Fig. 1.

2.To unlock the gun trigger safety, push the latch (A) out and turn it parallel with the gun body.

LOCKED

UNLOCKED

01464

Fig. 1

Installation/Operation

How to Use the Gun

1.Guide a grounded fluid hose (with spring guard) through the hose guard (14) and connect the hose to the gun inlet. See Fig. 2.

2.With no tip installed, start the pump. Flush the pump according to the instructions supplied with it. Prime the system with the fluid.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 5.

3.Relieve the pressure. Be sure the gun trigger safety is locked. See Fig. 1.

4.Model 235–459:Unscrew the tip guard (1) and install the tip (A) and the gasket (2d) in the nut of the tip guard. Screw the assembly firmly onto the gun. Tighten the assembly with a wrench. See Fig. 2.

NOTE: If the gasket (2d) is not installed, the gun will leak.

5.Models 235–459and237–691:install the SwitchTip (19) and the tip guard (18). See manual308–644,supplied.

1 A 2d

19

14

18

01463

Fig. 2

6.Start the pump. Adjust the fluid pressure until the spray is completely atomized. Use the lowest pressure necessary to get the desired results. Higher pressure may not improve the spray pattern and will cause premature tip wear and pump wear.

7.If adjusting the pressure does not give a good spray pattern, follow the Pressure Relief Procedure on page 5 and then try another tip size.

8.Use a full-open,full-closetriggering action. Hold the gun about 14 in. (350 mm) from and at right angles to the work surface. Don’t swing the gun in an arc. Practice to find the best length and speed of stroke.

How to Adjust the Spray Pattern.

1.To adjust the spray pattern direction, follow the

Pressure Relief Procedure on page 5. Loosen the tip guard retaining nut (B). Turn the tip guard/ tip groove horizontally (C) for a horizontal pattern and vertically (A) for a vertical pattern. Tighten the retaining nut.

2.The spray tip orifice and spray angle determines the coverage and size of the pattern. When more coverage is needed, use a larger spray tip rather than increasing the fluid pressure.

CAUTION

The openings in the tip guard reduce paint buildup on the tip guard while spraying. Any damage to the sharp edges of the openings causes paint to collect at that area. Never hang the gun by the tip guard.

KEY

A Tip guard shown in position for vertical spray pattern

B Retaining nut

C Tip guard shown in position for horizontal spray pattern

B C

A

Fig. 3

68

Installation/Operation

How to Clean the Spray Tip

and Clear a Spray Tip Obstruction.

WARNING

To reduce the risk of fluid injection or splashing in the eyes or on the skin, do not hold a hand, body or rag in front of the spray tip when cleaning or checking a clogged tip. Point the gun toward the ground or into a waste container when checking to see if the spray tip is cleared.

Do not try to “blow back” paint; this isnot an air spray gun.

Do not wipe fluid buildup off the gun or spray tip until pressure is relieved.

Cleaning during the day.

1.Follow the Pressure Relief Procedure,page 5.

2.Clean the front of the tip frequently during the day to help reduce buildup. Also clean the tip and tip guard at the end of each work day. Use a solventsoaked brush to clean the spray tip.

Clearing an obstruction.

If the spray tip clogs while spraying, immediately stop spraying, then:

Gun 235–458– with standard tip guard

1.Engage the trigger safety latch, open the pressure drain valve.

2.Remove the spray tip and blow out the obstruction by applying air to the front of the spray tip. Or, let the spray tip and gun nozzle soak to dissolve the obstruction. If it won’t dissolve, jar it out by tapping the back of the spray tip against a flat surface.

CAUTION

Never soak the entire gun in solvent. Prolonged exposure to solvent can ruin the packings.

Gun 235–459and237–691–with RAC IV tip guard

1.Engage the trigger safety latch. Rotate the RAC IV tip handle 180_. See Fig. 4.

2.Disengage the trigger safety latch. Trigger the gun into a pail or onto the ground to remove clog.

3.Engage the trigger safety latch. Rotate the tip handle to the spraying position.

4.If the tip is still clogged, lock the gun trigger safety, shut off the sprayer and disconnect the power source, and open the pressure drain valve to relieve pressure. Clean the spray tip as shown in manual 308–644,supplied with the RAC IV.

KEY

A Handle shown in spraying position. Turn handle 180_ and trigger gun to clear clog.

A

Fig. 4

8 7

Installation/Operation

How to Check the Gun Diffuser Operation

Check the diffuser operation weekly. The gun diffuser/ seat (2a) breaks up spray and reduces the risk of fluid injection when the tip is not installed. Perform the test below. If it fails, replace the entire Needle Kit, Part No. 235–474,as instructed on page 7. Diffuser/seats are not sold separately since the gun will leak if an old needle is used with a new diffuser/seat.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 5.

1.Follow the Pressure Relief Procedure, page 5.

2.Remove the tip guard and spray tip.

3.Start the sprayer and adjust it to the lowest pressure.

4.Aim the gun into a grounded metal pail while holding it firmly to the pail. Trigger the gun. If the fluid emitted is not diffused into an irregular stream, replace the entire needle kit immediately. See Fig. 5.

2a

Fig. 5

How to Flush the Gun.

Always flush the pump and the gun before the fluid being sprayed can dry in it.

NOTE: If it is available, the flushing procedure provided in your pump or sprayer manual should be used instead of this procedure.

WARNING

FIRE AND EXPLOSION HAZARD

Static sparking and splashing may cause

fire, explosion and serious injury. To reduce static sparking and splashing,

always remove the spray tip from the gun, and hold a metal part of the gun firmly to the side of a grounded metal pail when flushing.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 5.

1.Follow the Pressure Relief Procedure,page 5.

2.Remove the tip guard and spray tip. Soak and clean the parts.

3.Put the pump intake in a grounded pail of water or solvent.

4.Start the pump at its lowest pressure.

5.Trigger the gun into the original pail. When solvent appears, release the trigger.

6.Now trigger the gun into the solvent pail. Circulate the fluid until the system is thoroughly flushed.

7.Follow the Pressure Relief Procedure, page 5.

Service

CAUTION

Do not attempt to install an old style needle in this gun. The front of the new needle is marked with a + below the Graco symbol.

Notes:

Use Needle Kit 235–474.

Use all the new parts for the best results. Parts included in the kit are shown with one asterisk, (2a*).

Keep parts very clean. Dried paint or other contaminants cause friction which causes parts to wear faster.

Needle Replacement.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 5.

1.Follow the Pressure Relief Procedure, page 5.

2.Remove the hose, tip guard, spray tip and gasket.

3.Remove the diffuser/seat (2a*) and gasket (2b*). Remove the screw (12), pivot pin (11), and trigger

(8). See Fig. 6.

 

Lubricate, then torque

11

to 20–25ft–lb(27–34N.m)

 

 

 

 

2b*

8

 

2a*

12

4.Insert a punch into the rear of the gun and tap it to push the needle (2c*) out the front of the gun. See Fig. 7.

2c

Fig. 7

02350

 

5.Clean the internal passages of the gun.

6.Grease the rings (A) of the new needle (2c*). See Fig. 8.

A

Fig. 8

Fig. 6

02349

9

Service

7.Slide the rear of the needle (2c*) into the front of the gun. Slide the tool (B), provided with the repair kit, into the gun, around the needle. Lightly tap the tool with a hammer or lightly press the tool against a flat surface to seat the needle. See Fig. 9. Remove the tool.

CAUTION

Tapping or pressing the tool too hard may jam the tool and damage the needle.

8.Grease the end of the needle.

9.Grease the diffuser/seat threads. Place the new gasket (2b*) on the diffuser/seat (2a*) and screw the assembly into the fluid housing (7). Torque to 20–25ft-lb(27–34N.m). See Fig. 6.

10.Install the trigger (8), pivot pin (11) and screw (12). See Fig. 6.

NOTE: No needle or trigger adjustment is needed.

B

2c

Fig. 9

02351

 

1 3 8 235

Parts

 

 

6

 

 

2

 

 

2

 

 

2c*

 

 

2b*

4

2d*

1 2a*

 

1

19

18

Model 235–459,Series D

Model 237–691,Series B

ncludes RACr IV DripLesst Tip Guard.

Includes items 2 to 19 as indicated by model number.

Model 235–457,Series C

Includes the Standard (non-reversing)DripLesst Tip Guard.

Includes items 2 (not 2d) to 17 as indicated by model number.

Model 235–458,Series C

Includes the Standard (non-reversing)DripLesst Tip Guard.

Includes items 1 to 17 as indicated by model number.

Ref

 

 

No.

Part No. Description

Qty.

1220–222STANDARD TIP GUARD

 

 

Model 235–458only

1

2

235–474

NEEDLE KIT

1

 

 

Includes items 2a to 2d

2a*

Z

DIFFUSER/SEAT

1

2b*

Z

GASKET, copper

1

2c*

Z

NEEDLE

1

2d*

166–969

TIP GASKET

1

 

 

Use in gun model 235–458only

11

 

3

9

12

 

 

7

8

 

 

 

 

13

 

 

 

14

15

Lubricate, then

1torque to 20-25ft-lb(27-34N.m)

2Lubricate

Torque to 30-40in-lb3(3.4–4.5N.m)

4Purchase separately

 

 

 

01468

Ref

 

 

 

No.

Part No.

Description

Qty.

6

169–797

ADAPTER

1

7

187–972

FLUID HOUSING

1

8

187–985

TRIGGER

1

9

102–207

SETSCREW, 1/4–20

1

11

187–965

PIVOT PIN

1

12

203–953 SCREW, hex washer hd,10–24

1

13

235–470

GUN HANDLE

1

14

218–139

HOSE HOLDER

1

15

107–257

CAPSCREW, 1/4–20x 1/2”

1

16Y

187–987WARNING TAGnot shown

1

 

 

Model 235–458only

Y187–346WARNING SHEETnot shown

 

Model 235–459only

1

17Y

222–385WARNING CARDnot shown

1

18

220–422RAC IV DripLess TIP GUARD

1

 

Model 235–459only

19

221–517SwitchTip, Size 517

1

 

Model 235–459only

*These parts are also included in Repair Kit 235–474,which may be purchased separately. Kit also includes installation tool.

Z Part not sold separately.

Y Replacement Danger and Warning labels, tags, and cards are available at no cost.

3 8 235 11

Notes

12 3 8 235

Accessories

FILTERS

3000 psi (210 bar) Maximum Working Pressure.

Adequate filtering is important for a good surface finish and to minimize tip clogging. These filters provide secondary filtering. Various screen meshes are available.

Mounts in hose

213–068 Includes filter body, spring and one 100 mesh screen.

213–069 Includes filter spring and one 60 mesh screen.

Use with above filter body.

210–742 Includes filter spring and one 100 mesh screen.

Use with above filter body.

210–729 Includes assembly213–068plus a 3 ft (0.9 m) whip hose for more flexible gun movement.

Mounts between hose and gun

210–500 Includes swivel, adapter and one 60 mesh screen

Replacement screens for above filters

210–731 Three 60 mesh (250 micron) screens210–732 Three 100 mesh (149 micron) screens210–733 Three 200 mesh (74 micron) screens

SWIVELS and WHIP HOSES

Swivels and whip hoses provide more flexible gun movement for easier handling and less fatigue. Working pressures are listed in the descriptions.

207–946 Swivel, 1/2 npsm x 3/8 npt(f)

5000 psi (350 bar) Max. Working Pressure

204–940 Swivel, 1/4 npt x 1/4 npsm

3000 psi (210 bar) Max. Working Pressure

214–701 Whip hose, nylon, coupled 1/4 npsm(f) x 3/8 npt(m), spring guards both ends.

3000 psi (210 bar) Max. Working Pressure

TOOLS

NYLON BRUSHES

Use to thoroughly clean the gun’s fluid passages.

101–891 0.375” (9 mm) dia.101–892 0.625” (16 mm) dia.

WRENCH 171–147

Fits all hexes on the gun.

NEEDLE TOOL

188–369

Required to install new needle without damaging it.

TIP GUARDS

These tip guards fit all Graco airless spray guns. Choose the one that’s right for your application. One of these tip guards is included with every Graco airless gun.

220–422 RAC®IV DripLesst Tip Guard. Includes SwitchTip of choice. See your distributor for available sizes.

220–222 Standard DripLesst Tip Guard. Order flat tip separately. See your distributor for available sizes.

222–674 Heavy Duty RAC® DripLesst Tip Guard. Order SwitchTip separately. See your distributor for available sizes.

3 8 235 13

Technical Data

Maximum Working Pressure . . . . . . 5000 psi (350 bar) Fluid Orifice Size . . . . . . . . . . . . . . . . . 0.090 in. (2.3 mm Wetted Parts . . . . . . . . . Stainless steel, Polyethylene, Polyurethane, Nylon, PTFE R Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 oz. (510 g)

Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 npsm(m) Maximum material temperature . . . . . . . 120_F (50_C) Sound Data

Sound Pressure Level . . . . . . . . . . . . . . . . . 78 dB(A)* Sound Power Level . . . . . . . . . . . . . . . . . . . 87 dB(A)*

* Measured while spraying waterbase paint – gravity 1.36 through a 517 tip at 3,000 psi (207 bar).

Per ISO 3744

PTFER is a registered trademark of the DuPont Company.

Graco Phone

Number

TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:1–800–328–0211 Toll Free.

14 3 8 235

Manual Change Summary

Changed: Model 237–691,Series C

To: Model 237–691,Series B

3 8 235 15

The Graco Warranty and Disclaimers

WARRANTY

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Gracocomponent parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties (express or implied), including warranty of merchantability or warranty of fitness for a particular purpose, and of anynon–contractualliabilities, including product liabilities, based on negligence or strict liability. Every form of liability for direct, special or consequential damages or loss is expressly excluded and denied. In no case shall Graco’s liability exceed the amount of the purchase price. Any action for breach of warranty must be brought within two (2) years of the date of sale.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose, with respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.

Sales Offices: Atlanta, Chicago, Detroit, Los Angeles

Foreign Offices: Belgium, Canada, England, Korea, Switzerland, France, Germany, Hong Kong, Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

PRINTED IN U.S.A. 308–235December 1992, Revised February 1998

16 3 8 235