Graco Inc 240-363, 8119A, 308-8452, 240-350, 308-845, 240-362, 240-349, 240-352, 240-353, 240-351, 240361 User Manual

Size:
1.02 Mb
Download

INSTRUCTIONS–PARTSLIST

 

308–845

This manual contains important

 

Rev. C

 

 

warnings and information.

First choice when

READ AND KEEP FOR REFERENCE.

quality counts.

t

 

 

INSTRUCTIONS

 

 

ACETAL HUSKYt 307,WALL-MOUNTPUMP, DRUM SUCTION

PROt/ Delta Sprayt Packages

Metal fluid fittings and hose couplings are stainless steel.

100 psi (0.7 MPa, 7 bar) Maximum Fluid Working Pressure

100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure

Packages with Fluid Pressure Regulators

Model No. 240–349

with hoses and Delta Spray air spray gun

Model No. 240–350

with hoses and Delta Spray HVLP gun

Model No. 240–351no hoses or gun

Model No. 240–352

with hoses and PRO 3500sc electrostatic gun

Model No. 240–353

with hoses and PRO 4500sc electrostatic gun

Packages with Surge Tanks

Model No. 240–361

with hoses and Delta Spray air spray gun

Model No. 240–362

with hoses and Delta Spray HVLP gun

Model No. 240–363no hoses or gun

8119A

This gun and hose for PRO 3500sc Electrostatic package

This gun and hose for Delta Spray Air Spray package or Delta Spray HVLP package

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

Graco Inc. is registered to I.S. EN ISO 9001

Instruction Manual – Parts List Changes

This page contains a summary of changes or additions that do not appear in the contents of the manual.

308845 1A

Notes

308845 1B

Table of Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Parts List and Parts Drawing

240–349 to 240–353 . . . . . . . . . . . . . . . . . . 10

240–361 and 240–363 . . . . . . . . . . . . . . . . 12

Fluid Filter Kit 240–440 . . . . . . . . . . . . . . . . . . . 14

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Wall Mounting Hole Layout . . . . . . . . . . . . . . . . 15

Graco Standard Warranty . . . . . . . . . . . . . . . . . 16

Graco Phone Number . . . . . . . . . . . . . . . . . . . . . 16

Symbols

Warning Symbol

WARNINGARNING

This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the corresponding instructions.

WARNING

PRESSURIZED FLUID HAZARD

Spray from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin and cause serious injury.

DDo not stop or deflect fluid leaks with your hand, glove, or rag.

DFollow the Pressure Relief Procedure on page 6 before cleaning, checking, or servicing the equipment.

DTighten all fluid connections before each use.

DCheck the hoses, tubes, and couplings daily. Replace parts immediately if worn, damaged, or loose. Permanently coupled hoses cannot be repaired.

FIRE AND EXPLOSION HAZARD

Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and result in fire or explosion and serious injury.

DGround the equipment, personnel in or close to the spray area, the object being sprayed, and all other electrically conductive objects in the spray area. See Grounding on page 5.

DIf there is any static sparking while using the equipment, stop spraying immediately. Identify and correct the problem.

DProvide fresh air ventilation to avoid the buildup of flammable vapors from the solvent or the fluid being sprayed.

DDo not smoke in the spray area.

DExtinguish all open flames or pilot lights in the spray area.

DDo not turn on or off any light switch in the spray area.

DElectrically disconnect all equipment in the spray area.

DKeep the spray area free of debris, including solvent, rags, and gasoline.

DDo not operate a gasoline engine in the spray area.

2308-845

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result INSTRUCTIONS in a serious injury.

DThis equipment is for professional use only.

DRead all the instruction manuals, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor.

DDo not alter or modify this equipment. Use only genuine Graco parts and accessories.

DCheck the equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum working pressure of the lowest rated system component. This package has a 100 psi (0.7 MPa, 7 bar) maximum working pressure.

DUse fluids that are compatible with the equipment wetted parts. See the Technical Data section of all the equipment manuals. Read the fluid manufacturer’s warnings.

DRoute the hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 180_F (82_C) or below–40_F(–40_C).

DDo not use the hoses to pull equipment.

DDo not move pressurized equipment.

DWear hearing protection when operating this equipment.

DComply with all applicable local, state, and national fire, electrical, and other safety regulations.

TOXIC FLUID HAZARD

Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the skin, swallowed, or inhaled.

DKnow the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.

DStore hazardous fluid in an approved container. Dispose of the hazardous fluid according to all local, state, and national guidelines.

DWear appropriate protective clothing, gloves, eyewear, and respirator.

DIf the pump diaphragm fails, hazardous fluid may be exhausted along with the air.

308-8453

Setup

CAUTION

This equipment is compatible with most water-basedmaterials. See the wetted parts in theTechnical Data section and your fluid and solvent manufacturer’s compatibility information.

Do not use acid catalyzed materials; they are incompatible with the acetal used in this pump.

WARNING

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or

swallowed.

DRead TOXIC FLUID HAZARDon page 3.

DUse fluids and solvents that are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals.

Read the fluid and solvent manufacturer’s warnings.

General Information

DAlways use Genuine Graco Parts and Accessories, available from your Graco distributor. See the Product Data Sheet for this package, Form No. 305–898.If you supply your own accessories, be sure they are adequately sized and pressure rated for your system.

DReference numbers and letters in parentheses refer to the callouts in the figures and the parts lists on pages 10 and 12.

Preparing the Operator

Anybody who operates this system should be trained in the safe, efficient operation of all system components. At a minimum, all operators should thoroughly read the safety, setup, and operation sections of this manual.

Preparing the Site

DUse a compressor capable of delivering 40 cfm (1.12 m3) and a minimum of 80 psi (552 kPa, 5.4 bar) for efficient operation.

DClear obstacles and debris that could cause an unsafe operating environment.

DRun a 1/2 in. I.D. air line from your compressed air supply to the pump location. Be sure the air is dry and filtered.

DWhen the bleed-typemaster air valve (K) is closed and the pump air regulator is opened, it relieves all air pressure to the system components.

DVentilate the spray booth.

WARNING

To prevent hazardous concentrations of toxic and/or flammable vapors, spray only in a properly ventilated spray booth. Never operate the spray gun unless ventilation fans are operating.

Check and follow all of the national, state, and local codes regarding air exhaust velocity requirements.

4308-845

Setup

Assembling the Wall-MountUnit

See Fig. 1

Install the wall bracket (G) 5 ft (1.5 m) above the floor. For proper hole dimensions, use the Wall Mounting Hole Layout on page 15. Be sure the wall is strong enough to support the weight of the pump and hoses, any accessories, the fluid, and stress caused by pump operation.

Screw the bung plug (R) into the drum bung opening. Adjust the suction tube (L) so the end of the tube is about 1/2 in. (13 mm) off the bottom of the drum, and secure the suction tube using the thumbscrew on the bung plug.

Hose Connections

This package is shipped with the hoses connected. Before you disconnect any hoses, make a note of the proper connections.

Flush Pump Before First Use

The pump was tested in water. If the test solution could contaminate the fluid you are pumping, flush the pump thoroughly with a compatible solvent. See

Flushing the System on page 8.

Grounding

WARNING

To reduce the risk of static sparking, the entire system must be grounded. Check your local electrical code for detailed grounding instructions for your area and type of equipment. Ground all of this equipment. Also read FIRE AND EXPLOSION HAZARD on page 2.

DPump: One end of the ground wire is already connected to the pump grounding strip. Connect the clamp end of the ground wire to a true earth ground.

DAir compressor: Follow the manufacturer’s recommendations.

DObject being sprayed: Follow the local code.

DFluid supply container: Follow the local code.

DAll solvent pails used when flushing: Follow the local code. Use only metal pails, which are conductive. Do not place the pail on a non-conductive surface, such as paper or cardboard, which interrupts the grounding continuity.

DSystems with PRO 3500sc and PRO 4500sc electrostatic gun: Make sure you read all of the grounding instructions and warnings in your gun instruction manual.

308-8455

Operation

Using the Gun

See the gun instruction manual for gun operation, care, flushing, cleaning, and technical data. Read the entire gun manual before operating the sprayer.

Pressure Relief Procedure

See Fig. 1

WARNING

The system remains pressurized until pressure is manually relieved. To reduce the risk of serious injury from pressurized fluid, accidental spray from the gun, or splashing of any fluid, follow this procedure whenever you

DStop spraying

DAre instructed to relieve pressure

DCheck or service any system equipment

DInstall, clean, or change spray nozzles

1.Turn off the air supply to the pump.

2.Be sure the pump air regulator is open by turning the knob (E) clockwise several turns.

3.Open the bleed-typemaster air valve (K) to relieve pump air pressure.

4.Trigger the gun (B) to relieve fluid pressure in the hoses.

Adjusting Pump and Gun Air Regulators

See Fig. 1

NOTE: The pump air regulator knob (E) and gun air regulator knob (F) have a locking feature. To unlock the knobs, pull out on them. You will feel them click out. To lock them at the desired setting, push them back into the locked position.

Always adjust the pump air regulator (E) and gun air regulator (F) slowly to prevent surging during startup. Turn the knobs clockwise to increase pressure, and counterclockwise to decrease air pressure.

1.Slowly adjust the pump air regulator (E), to set air pressure to approximately 60 psi (413 kPa, 4 bar).

2.If your system has a fluid pressure regulator, turn the fluid pressure regulator handle (G) to adjust the fluid pressure to 40 to 60 psi ( 276 to 413 kPa, 2.8 to 4 bar).

3.Slowly open the gun air regulator (F), and pull the gun trigger just enough to open only the air valve in the gun. With the gun air triggered, set the gun air pressure to 60 psi (413 kPa, 4 bar).

NOTE: Gun air pressure higher than 60 psi (413 kPa, 4 bar) will cause excessive overspray and lowered efficiency.

4.If your system has a fluid pressure regulator (G), fully trigger the gun, and fine tune the fluid pressure to obtain the desired atomization.

Systems with Fluid Pressure Regulator

See Fig. 1

With the fluid pressure regulator (G), you can control fluid pressure from the pump to the gun. For an accurate setting, adjust the fluid regulator only when the gun is triggered and fluid is flowing through the regulator. Be sure the jam nut under the T–handle(G) does not interfere with your adjustments. Tighten the jam nut to lock in the setting, if desired.

1.To open the fluid regulator, which allows fluid to flow, turn the T-handclockwise.

2.To close the fluid regulator, which restricts or shuts off the fluid flow, turn the T-handlecounterclockwise.

Systems with Surge Tank

See Parts Drawing on page 13

In systems with a surge tank (30), the fluid pressure is the same as the air pressure applied to the pump (pump has 1:1 ratio of fluid to air). Adjust the fluid pressure as required with the pump air regulator (E).

The surge tank filter screen may require periodic cleaning. First, relieve the pressure. Unscrew the surge tank cover from its base, and remove the filter screen. Clean the screen with a compatible solvent, and reinstall it in the surge tank. Make sure you reinstall the cover with a firm hand torque to ensure a good seal.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 6.

NOTE: The pump requires approximately 15 to 20 psi (103 to 138 kPa, 1 to 1.4 bar)to function. This is the lowest fluid pressure available. If lower fluid flow is required, a smaller fluid tip may be required on the spray device.

6308-845

Operation

Priming the System See Fig. 1

1.Close the gun air regulator (F).

2.If your system has a fluid pressure regulator (G), close it.

3.Open the bleed-typemaster air valve (K).

4.Slowly set the pump air regulator (E) pressure to 20 to 30 psi (140 to 210 kPa, 1.4 to 2.1 bar). The pump cycles quickly, then it slows down when it is primed. Set the pump air pressure to 40 psi (280 kPa, 2.8 bar).

5.Slowly open the gun air regulator (F), and pull the gun trigger just enough to open only the air valve in the gun. With the gun air triggered, set the gun air pressure to 60 psi (413 kPa, 4 bar).

6.Hold the gun against and aimed into a grounded metal waste pail, and fully trigger the gun. If your system has a fluid pressure regulator (G), slowly open it.

The gun emits air until the fluid arrives. When fluid flows freely, release the gun trigger.

Delta Spray

regulated Air Spray package or regulated HVLP package shown

B

C

F

D

E

KEY

AHusky 307 pump

BGun

CGun fluid hose

DGun air hose

EPump air regulator

FGun air regulator

GFluid pressure regulator

HPump ground wire

KBleed-typemaster air valve

LSuction tube

M

Front shield assembly

N

Back shield

P

P

Lifting handle

G

Q

Wall bracket

 

R

Bung plug

 

K

A

M

R

N

C

H

Q

L

Fig. 1

8120A

 

308-8457

Operation

When to Shut Down the System

Shut down the system at the end of the work shift and before checking, adjusting, cleaning, or repairing the system. Always relieve the pressure.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 6.

Flushing the System

Flush the system at the following times:

DBefore the first-timeuse

DWhen changing colors

DBefore fluid can dry or settle out in a dormant system.

DBefore storing the system

Flush the system as follows (See Fig. 1):

1. Relieve the pressure.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 6.

2.Remove the gun air cap before flushing, and clean it separately.

3.Place the suction tube into a grounded metal pail of compatible solvent.

4.Make sure the air regulators (E and F) are closed.

NOTE: The gun air regulator (F) always stays closed during flushing.

5.Open the bleed-typemaster air valve (K).

6.Slowly open the pump air regulator (E) until the pump starts.

7.Hold the gun against a grounded metal waste pail, and fully trigger the gun. If your system has a fluid pressure regulator (G), slowly open it until the fluid flows smoothly.

8.When solvent appears, release the gun trigger.

9.For a first-time flush: trigger the gun and flush with solvent for 30 seconds.

For flushing after spraying fluid: trigger the gun and flush with solvent until the system is thoroughly cleaned.

10.Repeat the procedure with clean solvent, if needed.

11.Lift the fluid intake tube from the fluid supply, and trigger the gun and run the pump until air comes from the gun.

12.Relieve the pressure.

The system is now ready to be stored or primed with another fluid. See Priming the System on page 7.

8308-845

Maintenance

See the separate component instruction manuals for individual component maintenance procedures.

Access to some system components requires that you remove the shields. The following steps are for shield removal. Shield replacement is the reverse of these steps, so make sure you take notes on the proper hose connections. Depending on your system, see the Parts Drawings on pages 11 and 13 for numbercall-outs.

Front Shield Assembly (1)

1.Disconnect the pump air hose from the pump air regulator.

2.Disconnect the gun air hose from the gun air regulator.

3.Loosen, but do not remove, the two front pump foot screws (24).

4.Loosen, but do not remove, the two top shield screws (32).

5.If your system has a fluid pressure regulator (50), make sure the T–handleis horizontal.

6.Pull the front shield assembly free of the system.

1g 1c

1a

1f

1e

 

 

1d

 

gun air

 

1b 1h

 

regulator

 

 

 

 

pump air

 

 

 

regulator

 

Front Shield Assembly Orderable Parts

 

Ref.

 

 

 

No.

Part No.

Description

Qty.

1a

192–995

SHIELD, front

1

1b

111–804

REGULATOR, air

 

 

 

See instruction manual 308–167

2

1c

160–430

GAUGE, pressure

2

1d

114–362

VALVE, ball

1

1e

159–840

ADAPTER

2

1f

188–077

NIPPLE

1

1g

114–369

FITTING, tube

1

1h

114–370

FITTING, tube

1

Fig. 2

 

 

8263A

 

 

 

Back Shield (25)

1.Disconnect the gun fluid hose from the fluid pressure regulator nipple (28) or surge tank nipple (7).

2.Disconnect the hose (16) that runs from the fluid pressure regulator or surge tank (50) to the elbow (40) on the pump outlet.

3.Loosen, but do not remove, the two top shield screws (32).

4.Loosen, but do not remove, the two back pump foot screws (24).

5.Pull the back shield free of the system. The fluid pressure regulator or surge tank (50) stays mounted to the back shield.

Gauge Lense Covers

Clear, stick-on/peel-offlense covers are available for the gauges. These covers protect the gauge lenses from spray. When they get too dirty to read the gauges, they can be peeled off, discarded, and replaced. Order as follows:

240–441 for2.5-inchgauges; package of 25 sheets, 12 lense covers to a sheet

240–442 for2-inchgauges; package of 25 sheets, 12 lense covers to a sheet

308-8459

Parts List

Wall-MountPackages with Fluid Pressure Regulators

Model No. 240–349,Delta Spray air spray packageModel No. 240–350,Delta Spray HVLP packageModel No. 240–351,no hoses (31) or gun (30)

Model No. 240–352,PRO 3500sc electrostatic packageModel No. 240–353,PRO 4500sc electrostatic package

Ref.

 

 

 

 

No.

Part No.

Description

 

Qty.

1

240–210

SHIELD ASSY, front

 

 

 

 

Contains 1a to 1h, shown in Fig. 2 on

 

 

page 9

 

1

2

110–789

WASHER, flat

 

2

3

100–014

SCREW

 

2

5

104–123

WASHER, spring lock

 

4

6

102–025

NUT, hex

 

4

7

192–994

HANDLE, shield

 

1

8

D31–331

PUMP, Husky 307

 

 

 

 

See instruction manual 308–553

 

1

9

054–139

TUBE, flexible

 

75 in.

10

111–864

CONNECTOR, male

 

1

11

188–181

PLUG, bung, airtight

 

1

12

111–276

SCREW, thumb

 

1

13

111–863

CONNECTION, union

 

1

15

054–175

HOSE; Nylon

 

10 in.

16

054–188

TUBE, PTFE R

 

9 in.

17

188–285

BRACKET, wall

 

1

19

112–899

WASHER, lock

 

1

20

112–903

NUT, hex

 

1

21

114–370

FITTING, tube, quick-connect

1

24

104–119

SCREW, cap, hex head

 

4

25

192–996

SHIELD, back

 

1

26

104–029

LUG, grounding

 

1

27

054–139

TUBE; Nylon

11.5 in.

28

189–436

NIPPLE

 

1

29Y

189–220

LABEL, warning

 

1

Ref.

 

 

 

 

No.

Part No.

Description

Qty.

30

239–542

GUN, Delta Spray, air spray

 

 

 

Model 240–349

 

 

 

See instruction manual 308–742

1

 

239–561

GUN, Delta Spray, HVLP

 

 

 

Model 240–350

 

 

 

See instruction manual 308–741

1

 

222–300

GUN, PRO 3500sc, electrostatic

 

 

 

Model 240–352

 

 

 

See instruction manual 307–912

1

 

224–200

GUN, PRO 4500sc, electrostatic

 

 

 

Model 240–353

 

 

 

See instruction manual 308–131

1

31

240–421

HOSE ASSY, air spray/HVLP;

 

 

 

25 ft (7.6 m)

Delta packages

1

 

240–425

HOSE ASSY, PRO gun;

 

 

 

25 ft (7.6 m)

PRO packages

1

32

100–333

SCREW, cap, hex head

2

33

114–369

FITTING, tube, quick-connect

1

34

193–251

LABEL, product

 

 

 

Delta packages

1

 

193–252

LABEL, product

 

 

 

PRO packages

1

37

238–909

GROUND WIRE & CLAMP ASSY

1

38

188–171

TUBE, suction

1

39

113–521

ELBOW, street

1

40

114–456

ELBOW, street

1

50

236–449

REGULATOR, fluid pressure;

 

 

 

0–30psi(0–207kPa,0–2bar)

 

 

 

Model 240–350

 

 

 

See instruction manual 308–325

1

 

236–450

REGULATOR, fluid pressure;

 

 

 

0–100psi(0–0.6MPa,0–7bar)

 

 

 

All Models except 240–350

 

 

 

See instruction manual 308–325

1

Y Extra Warning labels are available for free.

10 308-845

Parts Drawing

Wall-MountPackages with Fluid Pressure Regulators

Model No. 240–349,Delta Spray air spray packageModel No. 240–350,Delta Spray HVLP packageModel No. 240–351,no hoses (31) or gun (30)

Model No. 240–352,PRO 3500sc electrostatic packageModel No. 240–353,PRO 4500sc electrostatic package

Grounding Detail

26

37

19

20

27 8

1

21

34

15

27

15

33

24

17

5

 

 

6

 

30

222–300shown

32

50

39

16

 

28

2

3

29

 

 

25

7

 

 

 

 

 

 

24

16 40

10

9

13

9

11

12

30

38

31

31

8088A

308-84511

Parts List

Wall-MountPackages with Surge Tanks

Model No. 240–361,Delta Spray air spray package

Model No. 240–362,Delta Spray HVLP package

Model No. 240–363,no hoses (31) or gun (30)

Ref.

 

 

 

Ref.

 

 

 

 

No.

Part No.

Description

Qty.

No.

Part No.

Description

 

Qty.

1

240–210

SHIELD ASSY, front

 

25

192–996

SHIELD, back

 

1

 

 

Contains 1a to 1h, shown in Fig. 2 on

26

104–029

LUG, grounding

 

1

 

 

page 9

1

27

054–139

TUBE; Nylon

11.5 in.

3

106–285

BOLT, “U”

2

29Y

189–220

LABEL, warning

 

1

5

104–123

WASHER, spring lock

4

30

239–542

GUN, Delta Spray, air spray

 

 

6

102–025

NUT, hex

4

 

 

Model 240–361

 

 

7

188–089

NIPPLE

1

 

 

See instruction manual 308–742

 

1

8

D31–331

PUMP, Husky 307

 

 

239–561

GUN, Delta Spray, HVLP

 

 

 

 

See instruction manual 308–553

1

 

 

Model 240–362

 

 

9

054–139

TUBE, flexible

75 in.

 

 

See instruction manual 308–741

 

1

10

111–864

CONNECTOR, male

1

31

240–421

HOSE ASSY, air spray/HVLP;

 

11

188–181

PLUG, bung, airtight

1

 

 

25 ft (7.6 m)

 

1

12

111–276

SCREW, thumb

1

32

100–333

SCREW, cap, hex head

 

2

13

111–863

CONNECTION, union

1

33

114–369

FITTING, tube, quick-connect

1

15

054–175

HOSE; Nylon

10 in.

34

193–253

LABEL, product

 

1

16

054–188

TUBE, PTFE R

9 in.

37

238–909

GROUND WIRE & CLAMP ASSY 1

17

188–285

BRACKET, wall

1

38

188–171

TUBE, suction

 

1

19

112–899

WASHER, lock

1

40

114–456

ELBOW, street

 

2

20

112–903

NUT, hex

1

50

111–911

STRAINER, line

 

1

21

114–370

FITTING, tube, quick-connect

1

* These parts cannot be ordered separately.

 

 

24

104–119

SCREW, cap, hex head

4

 

 

 

 

 

 

 

Y Extra Warning labels are available for free.

12 308-845

 

Parts Drawing

 

 

Wall-MountPackages with Surge Tanks

 

 

Grounding Detail

 

Model No. 240–361,

Delta Spray air spray package

 

 

 

26

 

Model No. 240–362,Delta Spray HVLP package

 

 

 

 

37

Model No. 240–363,

no hoses (31) or gun (30)

 

 

 

 

 

 

 

 

 

19

 

 

 

 

 

 

20

 

 

 

 

 

3

 

 

 

 

 

7

50

 

 

 

 

 

32

 

 

 

 

 

 

 

40

16

 

 

 

 

 

 

 

 

27

 

29

 

 

 

 

8

 

25

 

 

 

 

 

 

 

 

1

 

 

16

24

 

 

 

 

 

 

 

 

 

21

 

 

 

 

 

34

15

 

 

 

 

 

 

 

 

40

 

 

 

 

 

 

 

 

 

27

 

 

10

 

 

 

15

 

 

9

 

 

 

33

 

 

13

 

 

 

 

 

 

 

 

 

17

 

 

9

 

 

 

24

5

 

11

 

 

 

 

6

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

30

 

 

 

 

 

 

 

 

38

 

 

 

 

 

31

 

 

 

 

 

 

 

8089A

 

 

 

 

 

 

 

308-845

13

Accessory Fluid Filter Kit

Fluid Filter Kit 240–440

Ref.

Part No.

Description

Qty.

No.

101

114–361

FILTER, fluid

1

102

113–322

CONNECTOR, male

1

103

054–188

TUBE; PTFE;R3/8” O.D.

8 in.

104

113–534ELBOW, male x female

2

105

111–917

NIPPLE; Nylon

1

The Fluid Filter Kit, listed above, can be installed to filter fluid drawn by the suction tube after it comes out of the pump. Install the Fluid Filter Kit as follows (see Fig. 3):

1.Apply thread sealant (specified in Fig. 3) to all male threads in this kit.

2.Remove the elbow (40) from the pump outlet, and remove the tube (16). See the Parts drawing on page 11.

3.Thread one the elbows (104) into the pump outlet.

4.Assemble the nipple (105) and the other elbow (104)

5.Thread the nipple (105), with the elbow (104) attached to it, into the elbow (104) that you threaded into the pump outlet.

6.Thread the fluid filter (101) onto the male threads of the elbow (104).

7.Thread the male connector (102) into the fluid filter (101).

8.Turn the fluid filter/male connector assembly towards the elbow (39). This makes connecting the tube (103) in step 9 easier.

9.Cut the PTFERtube (103) to the proper length, and install it to run from the male connector (102) to the elbow (39).

{To avoid sharp bends in the tube, you may have to cut it to a shorter length.

}Apply Graco Thread Sealer, or LoctiteR 567, or equivalent to male threads.

YFor initial installation, make sure the dome is firmly hand tightened onto the filter body. Do not use a tool. During subsequent service, hand tighten more firmly to prevent drips.

39

103{

103}

102}

101Y 104}

105}

104}

Fig. 3

8157A

 

 

14 308-845

Technical Data

 

 

Category

Data

 

 

Maximum fluid working pressure

100 psi (0.7 MPa, 7 bar)

 

 

Maximum incoming air pressure

100 psi (0.7 MPa, 7 bar)

 

 

Maximum operating temperature

120_ F (49_ C)

Gun

See separate gun instruction manual.

 

 

Pump

See separate pump instruction manual.

 

 

Fluid pressure regulator

See separate fluid pressure regulator instruction manual.

 

 

Air pressure regulators

See separate air pressure regulator instruction manual.

 

 

Wetted parts: fluid hoses for Delta guns

nylon, stainless steel

 

 

Wetted parts: fluid hoses for PRO guns

nylon, nickel-chromeplate

 

 

Wetted parts: other fluid hoses and tubing

nylon, PTFE R

Wetted parts: fluid fittings

nylon, acetal, 304/316 stainless steel

 

 

Weight (without hoses or gun):

 

 

 

packages with fluid pressure regulator

Approx. 29 lb (13 kg)

 

 

packages with surge tank

Approx. 27 (12 kg)

 

 

Sound data:

 

Sound power level*

 

68 dB(A)

at 70 psi 0.48 MPa, 4.8 bar) and 115 cpm

 

 

 

Sound pressure level

81.5 dB(A)

at 70 psi 0.48 MPa, 4.8 bar) and 115 cpm

 

 

 

* Sound power level was measured per ISO Standard 3744. TeflonR is a registered trademark of the DuPont Corporation.

Dimensions

11.5 in.

(292 mm)

9.0 in. 8182A

(229 mm)

Wall Mounting Hole

Layout

9.0 in.

(229 mm)

 

wall view of

5.0 in.

mounting bracket

(127 mm)

188–285

6.7 in.

(170 mm)

Four 0.438 in. (11 mm) dia. holes (to mount bracket to wall)

8.0 in.

(203 mm)

0654

308-84515

Graco Standard Warranty

Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Gracocomponent parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.

Graco Phone Number

TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:

1–800–367–4023Toll Free

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.

Sales Offices: Minneapolis, Detroit

Foreign Offices: Belgium, Korea, Hong Kong, Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 http://www.graco.com

e1998 Graco Inc. 308845 Rev. C January 2000 PRINTED IN U.S.A.

16 308845