Goodman Mfg RT6100004R13 User Manual

0 (0)
Goodman Mfg RT6100004R13 User Manual

Service Instructions

Split System Air Conditioners,

Split System Heat Pumps

with R-22 Refrigerant

Blowers, Coils, & Accessories

This manual is to be used by qualified, professionally trained HVAC technicians only. Goodman does not assume any responsibility for property damage or personal injury due to improper service procedures or services performed by an unqualified person.

Copyright © 2005 - 2009 Goodman Manufacturing Company, L.P.

RT6100004r13

May 2009

TABLE OF CONTENTS

IMPORTANT INFORMATION .........................

2 - 3

MODEL IDENTIFICATION ............................

4

- 15

AIR HANDLER/COIL IDENTIFICATION ............

 

15

ACCESSORIES .........................................

16

- 20

PRODUCT DESIGN .................................

21

- 22

SYSTEM OPERATION ..............................

23 - 27

TROUBLESHOOTING CHART .........................

28

SERVICING TABLE OF CONTENTS ................

29

SERVICING .................................................

30 - 60

ACCESSORIES WIRING DIAGRAMS ........

61 - 69

IMPORTANT INFORMATION

Pride and workmanship go into every product to provide our customers with quality products. It is possible, however, that during its lifetime a product may require service. Products should be serviced only by a qualified service technician who is familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts, testing instruments and the appropriate service manual. REVIEW ALL SERVICE INFORMATION IN THE APPROPRIATE

SERVICE MANUAL BEFORE BEGINNING REPAIRS.

IMPORTANT NOTICES FOR CONSUMERS AND SERVICERS

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

WARNING

This unit should not be connected to, or used in conjunction with, any devices that are not design certified for use with this unit or have not been tested and approved by Goodman. Serious property damage or personal injury, reduced unit performance and/or hazardous conditions may result from the use of devices that have not been approved or certified by Goodman.

WARNING

To prevent the risk of property damage, personal injury, or death, do not store combustible materials or use gasoline or other flammable liquids or vapors

in the vicinity of this appliance.

WARNING

Goodman will not be responsible for any injury or property damage arising fromimproper service or service procedures. If you perform service on your own product, you assume responsibility for any personal injury or property damage which may result.

To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this product. For further assistance, please contact:

CONSUMER INFORMATION LINE

CONSUMERINFORMATIONLINE

GOODMAN® BRAND PRODUCTS

AMANA® BRAND PRODUCTS

TOLL FREE 1-877-254-4729 (U.S. only)

TOLL FREE 1-877-254-4729 (U.S. only)

email us at: customerservice@goodmanmfg.com

email us at: hac.consumer.affairs@amanahvac.com

fax us at: (713) 856-1821

fax us at: (931) 4384362

(Not a technical assistance line for dealers.)

(Not a technical assistance line for dealers.)

Outside the U.S., call 1-713-861-2500. (Not a technical assistance line for dealers.) Your telephone company will bill you for the call.

Outside the U.S., call 1-931-433-6101. (Not a technical assistance line for dealers.) Your telephone company will bill you for the call.

2

IMPORTANT INFORMATION

SAFE REFRIGERANT HANDLING

While these items will not cover every conceivable situation, they should serve as a useful guide.

WARNING

Refrigerants are heavier than air. They can "push out" the oxygen in your lungs or in any enclosed space.To avoid possible difficulty in breathing or death:

Never purge refrigerant into an enclosed room or space. By law, all refrigerants must be reclaimed.

If an indoor leak is suspected, thoroughly ventilate the area before beginning work.

• Liquid refrigerant can be very cold. To avoid possible frostbite or blindness, avoid contact with refrigerant and wear gloves and goggles. If liquid refrigerant does contact your skin or eyes, seek medical help immediately.

Always follow EPA regulations. Never burn refrigerant, as poisonous gas will be produced.

WARNING

To avoid possible injury, explosion or death, practice safe handling of refrigerants.

To avoid possible explosion, use only returnable (not disposable) service cylinders when removing refrigerant from a system.

Ensure the cylinder is free of damage which could lead to a leak or explosion.

Ensure the hydrostatic test date does not exceed 5 years.

Ensure the pressure rating meets or exceeds 400

lbs.

When in doubt, do not use cylinder.

WARNING

System contaminants, improper service procedure and/or physical abuse affecting hermetic compressor electrical terminals may cause dangerous system venting.

Thesuccessfuldevelopmentofhermeticallysealedrefrigeration compressors has completely sealed the compressor's moving parts and electric motor inside a common housing, minimizing refrigerant leaks and the hazards sometimes associated with moving belts, pulleys or couplings.

Fundamental to the design of hermetic compressors is a method whereby electrical current is transmitted to the compressor motor through terminal conductors which pass through the compressor housing wall. These terminals are sealed in a dielectric material which insulates them from the housing and maintains the pressure tight integrity of the hermetic compressor. The terminals and their dielectric embedment are strongly constructed, but are vulnerable to careless compressor installation or maintenance procedures and equally vulnerable to internal electrical short circuits caused by excessive system contaminants.

In either of these instances, an electrical short between the terminal and the compressor housing may result in the loss of integrity between the terminal and its dielectric embedment. This loss may cause the terminals to be expelled, thereby venting the vaporous and liquid contents of the compressor housing and system.

A venting compressor terminal normally presents no danger to anyone, providing the terminal protective cover is properly in place.

If, however, the terminal protective cover is not properly in place, a venting terminal may discharge a combination of

(a)hot lubricating oil and refrigerant

(b)flammable mixture (if system is contaminated with air)

in a stream of spray which may be dangerous to anyone in the vicinity. Death or serious bodily injury could occur.

Under no circumstances is a hermetic compressor to be electrically energized and/or operated without having the terminal protective cover properly in place.

See Service Section S-17 for proper servicing.

3

PRODUCT IDENTIFICATION

 

Split System Air Conditioners R-22

Model #

Description

 

 

GSC13018-241AA

Goodman® Brand Split Condenser 13 Seer condensing units. Initial release. 26" chassis

 

 

GSC13036-481AA

Goodman® Brand Split Condenser 13 Seer condensing units. Initial release. 29" chassis

 

 

GSC13036,48*AA

Goodman® Brand Split Condenser 13 Seer condensing units.

Introduces new 13 SEER AC 3 PH R-22 Goodman Models

 

 

 

GSC130**1AB

Goodman® Brand Split Condenser 13 Seer condensing units. Move location of screw

hole.

 

 

 

GSC13036,48*AB

Goodman® Brand Split Condenser 13 Seer condensing units. Introduces new models

due to the replacement of 8-pole fan motors with 6-pole.

 

 

 

GSC13048*AC

Goodman® Brand Split Condenser 13 Seer condensing units. Move location of screw

hole.

 

 

 

GSC13018-30AC

Goodman® Brand Split Condenser 13 Seer condensing units. Release Models

containing the broad ocean motor 0131M00060

 

 

 

GSC13018,24, 301AD

 

GSC1300421AC, 484AC

Goodman® Brand Split Condenser 13 Seer condensing units. Remove 1 hairpin from

GSC13018, 24, 301AE

GSC130481, 483AE/AF

coil.

GSC130363AE/AF

 

GSC130361DE/DD

 

GSC13048*AD

Goodman® Brand Split Condenser 13 Seer condensing units. Release Models contain

the broad ocean motor 0131M00061

 

 

 

GSC130481AG

Goodman® Brand Split Condenser 13 Seer condensing units. Introduces new models

with Bristol compressors.

 

 

 

GSC130181BA

Goodman® Brand Split Condenser 13 Seer condensing units. Conversion of existing

models using 3/8" diameter tube coils to 5 mm coils.

 

 

 

GSC130361BA

Goodman® Brand Split Condenser 13 Seer condensing units. Initial release. 35"

chassis.

 

 

 

GSC130361BA

Goodman® Brand Split Condenser 13 Seer condensing units. Release Model with

Copeland Scroll Compressor.

 

 

 

GSC130361BB

Goodman® Brand Split Condenser 13 Seer condensing units. Introduces new models

due to the replacement of 8-pole fan motors with 6-pole.

 

 

 

GSC130361DF

Goodman® Brand Split Condenser 13 Seer condensing units. Introduces new models

with Bristol compressors.

 

 

 

GSC13024-301CA

Goodman® Brand Split Condenser 13 Seer condensing units. Introduces models with

reduced chassis size from the current 29x32.5 to 26x32

 

 

 

GSC130241DA

Goodman® Brand Split Condenser 13 Seer condensing units. Release of Goodman 13

SEER Condensers, with 5 mm coils; compressor change:CR18K7-PFV-230; reduced

 

refrigerant charge.

GSC130361FA

Goodman® Brand Split Condenser 13 Seer condensing units. Converts from 3/8" to

GSC130363BA

5mm. 2.5 & 3 ton units have new coil slab height and new louver panels. 2.5 - small

GSC130301DA

chassis; 3 ton medium chassis.

4

PRODUCT IDENTIFICATION

Split System Air Conditioners R-22

Model #

Description

 

 

GSC140**1AA

Goodman® Brand Split Condenser 14 Seer condensing units. Introduces Goodman®

Brand 14 Seer AC R-22 models.

 

 

 

GSC140**1AB

Goodman® Brand Split Condenser 14 Seer condensing units. New revisions have screw

locations moved in the top panel, base pans, louvers, and control box covers.

 

 

 

GSC140**1AC

Goodman® Brand Split Condenser 14 Seer condensing units. Release models

containing the Broad Ocean motor 0131M00060 and 0131M00061

 

 

 

GSC140**1AD

Goodman® Brand Split Condenser 14 Seer condensing units. Revise condenser coils by

removing (1) hairpin. Reducing refrigerant quantities by 6 ounces.

 

 

 

GSC14018-421BA

Goodman® Brand Split Condenser 14 Seer condensing units. Conversion of existing

models using 3/8" diameter tube coils to 5 mm coils.

 

 

 

 

Split System Air Conditioners R-22

 

 

 

Model #

 

Description

 

 

 

ASC130**1AA

Amana® Brand Split Condenser 13

Seer condensing units. Initial release new models of

Amana® Brand Deluxe 13 Seer AC R-22 conditioners.

 

ASC130**1AB

Amana® Brand Split Condenser 13

Seer condensing units. Move location of screw hole.

 

 

 

ASC130**1AC

Amana® Brand Split Condenser 13

Seer condensing units. Introduces horizontal style

louvers.

 

 

 

ASC1301**1AD

Amana® Brand Split Condenser 13 Seer condensing units. Remove 1 hairpin from coil.

 

 

ASC130601BD

Special High Feature Split XCondenser 14 Seer condensing units.. Remove 1

hairpin from coil. Reduce refrigerant quantities by 6 ounces.

 

 

 

 

 

Split System Air Conditioners R-22

 

 

Model #

Description

 

 

VSC13018-601AA

Value Split Condenser 13 Seer condensing units. Introduces Value 13 Seer AC R-22

models. 2 year part & 5 year compressor warranty in Bahama Beige.

 

 

 

5

PRODUCT IDENTIFICATION

Split System Heat Pumps R-22

Model #

 

Description

 

 

GSH10***AA

Goodman® Brand Split Heat Pump 10 Seer heat pump units. Initial release.

 

 

 

 

GSH10***AB

Goodman® Brand Split

Heat Pump 10

Seer heat pump units. Screw locations

moved in the top panel, base pans, louvers, and control box covers. .

 

GSH13***AA

Goodman® Brand Split Heat Pump 13 Seer heat pump units. Initial release.

 

 

 

 

Goodman® Brand Split Heat Pump 13

Seer heat pump units. Revision

GSH13**1AB

introduces the following new models due to the replacement of 8-pole fan motors

with 6-pole and screw locations moved in the top panel, base pans, louvers, and

 

 

control box covers.

 

 

 

 

 

 

Goodman® Brand Split Heat Pump 13

Seer heat pump units. Contain Broad

GSH13**1AC

Ocean motors Screw locations moved in the top panel, base pans, louvers, and

 

control box covers. .

 

 

 

 

 

GSH13036-48*AD

Goodman® Brand Split Heat Pump 13

Seer heat pump units. Introduces models

that contain the broad ocean motor

 

 

 

GSH13018-301BA

Goodman® Brand Split

Heat Pump 13

Seer heat pump units. Reduction in

chassis size from medium to small.

 

 

 

 

 

 

 

GSH130421AE

Goodman® Brand Split

Heat Pump 13

Seer heat pump units. Replaces V10

reversing valve with V6 reversing valve.

 

 

 

GSH13048*AG

Goodman® Brand Split

Heat Pump 13

Seer heat pump units. Introduces

model with Bristol Compressors.

 

 

 

GSH13036*BA/BB

Goodman® Brand Split Heat Pump 13

Seer heat pump units. Improvements to

increase MOP values on 3 ton units.

 

 

 

 

 

 

GSH140**1AA

Goodman® Brand Split Heat Pump 14

Seer heat pump units. Initial release.

 

 

 

GSH140**1AB

Goodman® Brand Split Heat Pump 14

Seer heat pump units. Screw locations

moved in the top panel, base pans, louvers, and control box covers.

 

 

 

 

 

GSH140**1AC

Goodman® Brand Split

Heat Pump 14

Seer heat pump units. Releases

models with the Broad Ocean motor.

 

 

 

 

 

 

 

GSH140361AF,

Goodman® Brand Split

Heat Pump 14

Seer heat pump units. Releases

GSH140421-48AD

models that replace TXV & compensator with flowrator & accumulator.

GSH140601AE

 

 

 

 

 

 

 

6

PRODUCT IDENTIFICATION

Split System Heat Pumps R-22

Model #

 

Description

 

 

 

 

ASH130**1AA

Amana® Brand

Split Heat Pump 13

Seer heat pump units. Initial release new

models of Amana® Brand Deluxe 13 Seer R-22 heat pumps.

 

 

 

 

 

ASH130**1AB

Amana® Brand

Split Heat Pump 13

Seer heat pump units. New revisions have

screw locations moved in the top panel, base pans, louvers, and control box

 

covers.

 

 

ASH130**1AC

Amana® Brand

Split Heat Pump 13

Seer heat pump units. New revisions have

horizontal style louvers.

 

 

 

 

 

 

 

Split System Heat Pumps R-22

Model #

 

Description

 

 

 

VSH1318-601AA

Value Split

Heat Pump 13 Seer heat pump units. Introduces Value 13 Seer HP R-

22 models. 2 year parts & 5 year compressor warranty in Bahama Beige.

 

 

 

 

7

PRODUCT IDENTIFICATION

 

Single Piece Air Handlers

Model #

 

 

Description

 

 

 

 

 

 

ARUF****16AA

A Single Piece R Multi-Position PSC Motor Unpainted Flowrater Introduction of new 13

SEER Air Handler Models. All Models will be suitable for use with R-22 and R-410A

 

 

 

 

A Single Piece R Multi-Position PSC Motor Unpainted Flowrater.Revision replaces the

ARUF364216AB

current spot welded blower housing with the same cinched or crimped design used on

 

the 80% furnace line.

 

 

 

A Single Piece R Multi-Position PSC Motor Unpainted Flowrater.Revision replaces the

ARUF486016AB

current spot welded blower housing with the same cinched or crimped design used on

 

the 80% furnace line.

 

 

 

A Single Piece R Multi-Position PSC Motor Unpainted Flowrater.Revision replaces the

ARUF364216AC

current spot welded blower housing with the same cinched or crimped design used on

 

the 80% furnace line.

 

 

ARUF****16BA

A Single Piece R Multi-Position PSC Motor Unpainted Flowrater. Revision replaces all

 

 

 

 

 

ARUFcoils using wavy fin with louver enhanced fin.

 

 

 

ARUF****1BA

A Single Piece R Multi-Position PSC Motor Unpainted Flowrater Introducation of R-22

Only Air Handlers.

 

 

 

ARPF****16AA

A Single Piece R Multi-Position PSC Motor Painted Flowrater Introducation of new 13

SEER Air Handler Models. All Models will be suitable for use with R-22 and R-410A

 

 

 

 

A Single Piece R Multi-Position PSC Motor Painted Flowrater. Revision replaces the

ARPF364216AB

current spot welded blower housing with the same cinched or crimped design used on

 

the 80% furnace line.

 

 

 

A Single Piece R Multi-Position PSC Motor Painted Flowrater. Revision replaces the

ARPF486016AB

current spot welded blower housing with the same cinched or crimped design used on

 

the 80% furnace line.

 

 

ARPF****16BA

A Single Piece R Multi-Position PSC Motor Painted Flowrater. Revision replaces all

ARPFcoils using wavy fin with louver enhanced fin.

 

 

 

ARPF****1BA

A Single Piece R Multi-Position PSC Motor Painted Flowrater. Introducation of R-22

Only Air Handlers.

 

 

 

ADPF****16AA

A Single Piece Downflow PSC Motor Unpainted Flowrater. Introducation of new 13

SEER Air Handler Models. All Models will be suitable for use with R-22 and R-410A

 

 

 

 

A Single Piece Downflow PSC Motor Unpainted Flowrater. Revision replaces the current

ADPF364216AB

spot welded blower housing with the same cinched or crimped design used on the 80%

 

furnace line.

 

 

 

A Single Piece Downflow PSC Motor Unpainted Flowrater. Revision replaces the current

ADPF486016AB

spot welded blower housing with the same cinched or crimped design used on the 80%

 

furnace line.

 

 

 

A Single Piece Downflow PSC Motor Unpainted Flowrater. Revision replaces the current

ADPF304216AC

spot welded blower housing with the same cinched or crimped design used on the 80%

 

furnace line.

 

 

ADPF****1BA

A Single Piece Downflow PSC Motor Unpainted Flowrater Revision replaces all

ARPFcoils using wavy fin with louver enhanced fin.

 

 

 

 

 

 

 

8

PRODUCT IDENTIFICATION

 

Single Piece Air Handlers

 

Model #

Description

 

 

 

 

 

 

A Single Piece E Multi-Position Variable-Speed Painted Flowrator. Introducation of

AEPF****16AA

new 13 SEER Air Handler Models. All Models will be suitable for use with R-22 and

 

R-410A

 

AEPF****16BA

A Single Piece E Multi-Position Variable-Speed Painted Flowrator. Revision

introduces new models adding lower kw hit kits on the S&R plate

 

 

 

 

 

AEPF****16BB

A Single Piece E Multi-Position Variable-Speed Painted Flowrator. Revision

replaces the current spot welded blower housing with the same cinched or crimped

 

design used on the 80% furnace line.

 

AEPF****16CA

A Single Piece E Multi-Position Variable-Speed Painted Flowrator. Revision

replaces all ARPFcoils using wavy fin with louver enhanced fin.

 

 

 

 

 

AEPF****1BA

A Single Piece E Multi-Position Variable-Speed Painted Flowrator Introduction of R-

22 Only Air Handlers.

 

 

 

 

 

AEPF313716AA

A Single Piece E Multi-Position Variable-Speed Painted Flowrator (AEPF) and A

Single Piece S Multi-Position EEM motor Painted Flowrator (ASPF). Introduction of

ASPF313716AA

3-Ton Air Handler units with 3-row coil.

 

 

 

 

 

ASPF****16AA

A Single Piece S Multi-Position EEM motor Painted Flowrator. Introduces new

ASPF Air Handlers

 

 

 

 

 

 

A Single Piece S Multi-Position EEM motor Painted Flowrator. Revision introuces

ASPF****16BA

modified ASPF control scheme, to ensure blower operation during and after call for

 

heat on units with heat kits and replacing wavy fin with louver enhanced fin on coil

 

 

 

AWUF****1AA

A Single Piece Air Handler Wall Mount Unpainted Flowrator. Introduces

13 SEER

Dayton wall mount air handlers

 

 

 

AWUF****16AA

A Single Piece Air Handler Wall Mount Unpainted Flowrator. Introduces

13 SEER

Dayton wall mount air handlers. All Models will be suitable for use with R-22 and R-

 

410A

 

AWUF3005-101AA

A Single Piece Air Handler Wall Mount Unpainted Flowrator. Introduces

13 SEER

Dayton wall mount air handlers using a Burr Oak Louvered Fin coil.

 

 

 

 

 

AWUF****1BA

A Single Piece Air Handler Wall Mount Unpainted Flowrator. Revision replaces

current wavey fin design with new louvered fin design

 

 

 

 

 

AWUF370**16AA

A Single Piece Air Handler Wall Mount Unpainted Flowrator. Introduction of

AWUF37 Air Handlers for use with R-22 and R410A.

 

 

 

AWUF****16BA

A Single Piece Air Handler Ceiling Mount N Uncased Flowrater. Revision has

 

 

 

 

louver fins & replaces copper tube hairpins with aluminum hairpins.

 

 

 

 

 

ACNF****1AA

A Single Piece Air Handler Ceiling Mount N Uncased Flowrater. Revision release

all models of 13 SEER Dayton uncased air handlers.

 

 

 

 

 

 

 

ACNF****16AA

A Single Piece Air Handler Ceiling Mount N Uncased Flowrater. Revision release

 

 

 

all models of 13 SEER Dayton uncased air handlers.All Models will be suitable for

 

use with R-22 and R-410A

 

ACNF****1BA

A Single Piece Air Handler Ceiling Mount N Uncased Flowrater. Revision replaces

 

 

 

 

current wavey fin design with new louvered fin design

 

 

 

 

 

AH**-1*

A Single Piece Air Handler Hydronic Air Handler. Revision replaces the time delay

relay in the AH air handlers with the UTEC time delay control board.

 

 

 

9

PRODUCT IDENTIFICATION

 

MBR/MBE Air Handlers

Model #

Description

 

 

MBR****AA-1AA

Modular Blower R Multi-Position PSC Motor. Introduces module blower with PSC

blower motor.

 

 

 

MBE****AA-1AA

Modular Blower E Multi-Position Variable-Speed. Introduces module blower with

variable speed blower motor.

 

 

 

MBE****AA-1BA

Modular Blower E Multi-Position Variable-Speed.Revision introduces new models

adding lower kw hit kits on the S&R plate

 

 

 

 

 

 

Evaporator Coils

Model #

 

 

Description

 

 

 

 

CAUF*****6AA

C Indoor Coil A Upflow/Downflow Uncased Flowrator. Introduces 13 SEER CAUF

 

 

 

Dayton Upflow/Downflow coils.

 

 

 

CAUF*****6BA

C Indoor Coil A Upflow/Downflow Uncased Flowrator. Revision releases Burr Oak

 

 

 

Louvered Fin in place of the Wavy Fin currently in production.

 

 

 

CAPF*****6AA

C Indoor Coil A Upflow/Downflow Painted Flowrator. Introduces 13 SEER CAPF

 

 

 

Dayton Upflow/Downflow coils.

 

 

 

CAPF*****6BA

C Indoor Coil A Upflow/Downflow Painted Flowrator. Revision releases Burr Oak

 

 

 

Louvered Fin in place of the Wavy Fin currently in production.

 

 

 

CAPF/CAUF36***CA

C Indoor Coil A Upflow/Downflow [Painted or Uncased] Flowrator. Revision

 

 

 

redesigns for performance improvement from 2 row to 3 row.

 

 

 

CHPF*****6AA

C Indoor Coil Horizontal A Coil Painted Flowrator. Release 13 SEER CHPF

horizontal A coil.

 

 

 

 

C Indoor Coil Horizontal A Coil Painted Flowrator. Release 13 SEER CHPF

CHPF*****6BA

horizontal A coil. Revision releases Burr Oak Louvered Fin in place of the Wavy

Fin currently in production. The rows change by one, (i.e. 4 row to 3 row; 3 row to

 

 

2 row) where applicable.

 

 

 

 

CHPF1824A6CA

 

 

 

CHPF2430B6CA

 

 

 

CHPF3636B6CA

C Indoor Coil Horizontal A Coil Painted Flowrator. 13 SEER CHPF horizontal A

CHPF3642C6CA

coil, revision has louver fins & replaces copper tube hairpins with aluminum

CHPF3642D6CA

hairpins.

CHPF3743C6BA

 

 

 

CHPF3743D6BA

 

 

 

CHPF4860D6DA

 

 

 

CSCF*****6AA

C Indoor Coil S Horizontal Slab Coil C Upainted Flowrator. Release 13 SEER

CSCF slab horizontal coil.

 

 

 

 

C Indoor Coil S Horizontal Slab Coil C Upainted Flowrator. Revision releases Burr

CSCF*****6BA

Oak Louvered Fin in place of the Wavy Fin currently in production. The rows

 

change by one, (i.e. 4 row to 3 row; 3 row to 2 row) where applicable.

 

 

 

 

10

PRODUCT IDENTIFICATION

 

 

 

 

 

G

S

C

14

036

1

A

A

BRAND:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MINOR

G: Goodman® Brand /

 

 

 

 

 

 

 

 

 

 

 

REVISION:

Amana® Brand Distinctions

 

 

 

 

 

 

 

 

 

 

 

A: Initial Release

 

SEER:

 

 

 

A: Amana® Brand

 

 

10: 10 SEER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V: Value

 

 

13: 13 SEER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14: 14 SEER

 

 

 

 

 

MAJOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REVISION:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A: Initial Release

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAPACITY:

 

 

 

 

 

PRODUCT

 

 

 

 

 

018: 1.5 Tons

 

 

 

 

 

CATEGORY:

 

 

 

 

 

024: 2 Tons

 

 

 

 

 

S: Split System

 

 

 

 

 

030: 2.5 Tons

 

 

 

 

 

 

 

 

 

 

 

 

 

 

036: 3 Tons

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

042: 3.5 Tons

 

 

 

 

 

 

 

 

 

 

 

 

 

 

048: 4 Tons

 

 

 

 

 

 

 

 

UNIT TYPE:

 

 

 

 

 

 

 

C: Condenser R-22

 

 

060: 5 Tons

 

 

 

 

 

 

 

 

H: Heat Pump R-22

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ELECTRICAL:

 

 

 

 

 

 

 

 

 

 

 

 

 

1:

208-230V/1ph/60Hz

 

 

 

 

 

 

 

 

 

 

 

 

3:

208-230v/3ph/60Hz

 

 

 

 

 

 

 

 

 

 

 

 

4:

460v/3ph/60Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

PKF

036

2

A

 

 

 

 

 

 

 

 

 

REVISION:

PRODUCT CATEGORY:

 

 

 

 

 

 

 

A: Revision

 

C: Split System

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ELECTRICAL:

 

 

UNIT TYPE:

 

 

 

1:

208-230V/1ph/60Hz

 

 

E: Commercial Air Conditioner

 

 

2:

220-240V/1ph/50 Hz

 

 

K: Air Cojditioner

 

 

 

3:

208-230v/3ph/60Hz

 

 

P: Heat Pump

 

 

 

4: 308/415V/3ph/50Hz

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL CAPACITY:

 

 

 

 

 

 

018: 1.5 Tons

048:

4

Tons

 

 

024:

2 Tons

060:

5

Tons

 

 

 

030: 2.5 Tons

070:

5

Tons

 

 

036:

3 Tons

090: 7.5

Tons

 

 

 

042: 3.5 Tons

120:

10 Tons

 

 

 

 

 

 

 

 

 

 

 

 

11

PRODUCT IDENTIFICATION

 

 

 

C

KF

036

2

A

 

 

 

 

 

 

 

 

 

 

 

REVISION:

PRODUCT CATEGORY:

 

 

 

 

 

 

 

A: Revision

 

C: Split System

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ELECTRICAL:

 

 

UNIT TYPE:

 

 

 

1:

208-230V/1ph/60Hz

 

 

E: Commercial Air Conditioner

 

 

2:

220-240V/1ph/50 Hz

 

 

K: Air Cojditioner

 

 

 

3:

208-230v/3ph/60Hz

 

 

P: Heat Pump

 

 

 

4: 308/415V/3ph/50Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL CAPACITY:

 

 

 

 

 

 

 

 

018: 1.5 Tons

048:

4

Tons

 

 

 

 

024:

2 Tons

060:

5

Tons

 

 

 

 

 

 

030: 2.5 Tons

070:

5

Tons

 

 

 

 

036:

3 Tons

090: 7.5

Tons

 

 

 

 

 

 

042: 3.5 Tons

120:

10 Tons

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

KL

036

2

A

 

 

 

 

 

 

 

 

 

REVISION:

PRODUCT CATEGORY:

 

 

 

 

 

 

 

A: Revision

 

C: Split System

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ELECTRICAL:

 

 

UNIT TYPE:

 

 

 

1:

208-230V/1ph/60Hz

 

 

E: Commercial Air Conditioner

 

 

2:

220-240V/1ph/50 Hz

 

 

K: Air Cojditioner

 

 

 

3:

208-230v/3ph/60Hz

 

 

P: Heat Pump

 

 

 

4: 308/415V/3ph/50Hz

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL CAPACITY:

 

 

 

 

 

 

018: 1.5 Tons

048:

4

Tons

 

 

024:

2 Tons

060:

5

Tons

 

 

 

030: 2.5 Tons

070:

5

Tons

 

 

036:

3 Tons

090: 7.5 Tons

 

 

 

042: 3.5 Tons

120:

10

Tons

 

 

 

 

 

 

 

 

 

 

 

 

12

PRODUCT IDENTIFICATION

C

E

120

5

A

 

 

 

 

 

 

 

 

 

 

REVISION:

PRODUCT CATEGORY:

 

 

 

 

 

 

 

 

A: Revision

 

C: Split System

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ELECTRICAL:

 

 

UNIT TYPE:

 

 

 

1: 208-230V/1ph/60Hz

 

 

E: Commercial Air Conditioner

 

 

2:

220-240V/1ph/50 Hz

 

 

K: Air Cojditioner

 

 

 

3:

208-230v/3ph/60Hz

 

 

P: Heat Pump

 

 

 

4: 308/415V/3ph/50Hz

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL CAPACITY:

 

 

 

 

 

 

018: 1.5 Tons

048:

4

Tons

 

 

024:

2 Tons

060:

5

Tons

 

 

 

030: 2.5 Tons

070:

5

Tons

 

 

036:

3 Tons

090: 7.5 Tons

 

 

 

042: 3.5 Tons

120:

10

Tons

 

 

 

 

 

 

 

 

 

 

 

 

 

THIS NOMENCLATURE IS TO BE USED TRHOUGH JULY 2006

 

A

R U

F

 

 

 

 

 

 

Product Type

A: Single Piece Air Handler

Application

C:Ceiling Mount PSC Motor

D:Downflow PSC Motor

E:Multi-Position Variable Speed Motor

R:Multi-Position PSC Motor

W:Wall Mount PSC Motor

Cabinet Finish

U: Unpainted

P: Painted

N: Uncased

Expansion Device

F: Flowrater

3642

1

A

A

 

 

 

 

 

Minor Revision

A: Initial Release

Major Revision

A: Initial Release

Electrical

1: 208/230V, 1 Phase, 60 Hz

Nominal Capacity Range @ 13 SEER

Multi-Position & Downflow Applications

3642: 3 - 3 1/2 tons 1830: 1 1/2 - 3 1/2 tons

1729: 1 1/2 - 2 1/2 Tons 10 SEER (for export systems)

Ceiling Mount & Wall Mount Applications

1805: Nominal Cooling Capacity

Electric Heat kw - 1 1/2 tons Cooling/5 kw Electric Heat 2405: Nominal Cooling Capacity

Electric Heat kw - 2 Tons Cooling/5 kw Electric Heat 3608: Nominal Cooling Capacity

Electric Heat kw - 3 Tons Cooling/8 kw Electric Heat

13

PRODUCT IDENTIFICATION

THIS NOMENCLATURE IS TO BE USED AFTER JULY 2006

A

W

U

F

 

 

EXPANSION

PRODUCT

 

DEVICE:

TYPE:

 

F: Flowrater

A: Air Handler

 

T: TXV

 

 

(Expansion

 

 

 

Device)

 

 

 

CABINET FINISH:

U: Unpainted

P: Paited

N: Uncased

APPLICATION

C:Ceiling Mount PSC Motor

D:Downflow PSC Motor

E:Multi-Position Varible-Speed Motor

S:Energy-Efficient Motor

R:Multi-Position PSC Motor

T:Coated Coils

W:Wall Mount PSC Motor

3642

1

6

A

A

MINOR

REVISION*

MAJOR

REVISION*

REFRIGERANT CHARGE:

No Digit: R-22 Only

6:R-410A or R-22

ELECTRICAL:

1: 208-230V/1ph/60Hz

NOMINAL CAPACITY RANGE:

@ 13 SEER

Dedicated Application

3636: 3 Tons

Multi-Position & Downflow Applications 3137: 3 Tons

3642: 3 - 3 1/2 Tons 1830: 1 1/2 - 3 1/2 Tons @10 SEER

1729: 1 1/2 - 2 1/2 Tons (for export systems)

Ceiling Mount & Wall Mount Applications

(Nominal Cooling Capacity/Electric Heat kW)

1805: 1 1/2 Tons Cooling / 5 kW Electric Heat

2405: 2 Tons Cooling / 5 kW Electric Heat

3608: 3 Tons Cooling / 8 kW Electric Heat

3705: 3 Tons Cooling / 5 kW Electric Heat

3708: 3 Tons Cooling / 8 kW Electric Heat

All Airhandlers use DIRECT DRIVE MOTORS. Power supply is AC 208-230v, 60 hz, 1 phase.

14

PRODUCT IDENTIFICATION

 

 

 

 

C

A

P

F

1824

A

6

A

 

 

 

 

EXPANSION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REVISION

 

PRODUCT

 

 

DEVICE:

 

 

 

 

 

A: Revision

 

TYPE:

 

 

F: Flowrater

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C: Indoor Coil

 

 

 

 

 

 

 

 

REFRIGERANT

 

 

 

 

 

 

 

 

 

 

 

 

 

CHARGE:

 

 

 

 

 

 

 

 

 

 

 

6: R-410A or R-22

 

 

 

 

CABINET FINISH:

 

 

 

 

2: R-22

 

 

 

 

U: Unpainted

 

 

 

 

4: R-410a

 

 

 

 

P: Painted

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N: Unpainted Case

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL WIDTH FOR GAS FURNACE

 

 

 

 

 

 

 

 

 

A: Fits 14" Furnace Cabinet

 

 

 

 

 

 

 

 

 

B: Fits 17 1/2" Furnace Cabinet

 

 

 

 

 

 

 

 

 

C: Fits 21" Furnace Cabinet

 

APPLICATION

 

 

 

 

 

 

 

 

 

 

 

D: Fits 24 1/2" Furnace Cabinet

 

A: Upflow/Downflow Coil

 

 

 

 

 

 

 

 

 

 

 

N: Does Not Apply (Horizontal Slab Coils)

 

H: Horizontal A Coil

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S: Horizontal Slab Coil

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL CAPACITY RANGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

@ 13 SEER

 

 

 

 

 

 

1824: 1 1/2 to 2 Tons 3030: 2 1/2 Tons 3636: 3 Tons

3642: 3 to 3 1/2 Tons 4860: 4 & 5 Tons

MB

R

8

00

A

A

1

 

 

 

 

 

 

 

 

 

 

ELECTRICAL SUPPLY:

 

DESIGN SERIES:

 

 

 

 

 

 

 

 

1: 208-230V/60hZ/1 ph

 

MB: Modular Blower

 

 

FACTORY HEAT

 

 

 

 

 

 

 

 

 

 

 

00: No Heat

 

DESIGN SERIES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A: First Series

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOTOR TYPE:

 

 

 

 

 

 

 

 

 

 

 

 

R: Constant Speed

 

 

 

 

 

 

 

 

 

 

 

 

E: Variable Speed

 

 

 

CIRCUIT BREAKER

 

 

 

 

 

 

 

 

 

 

 

A: No Circuit Breaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B: Circuit Breaker

 

 

MFG.#

 

 

AIRFLOW DELIVERED

 

 

 

 

 

MODEL

 

 

 

 

 

 

 

 

 

08: 800 CFM

 

 

 

 

 

MBR0800

MBR0800

 

 

12: 1200 CFM

 

 

 

 

 

MBR1200

MBR1200

 

 

 

 

 

 

 

MBR1600

MBR1600

 

 

16: 1600 CFM

 

 

 

 

 

 

 

 

 

 

 

 

MBR2000

MBR2000

 

 

20: 2000 CFM

 

 

 

 

 

 

 

 

 

 

 

 

MBE1200

MBE1200

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBE1600

MBE1600

 

 

 

 

 

 

 

 

 

 

MBE2000

MBE2000

15

ACCESSORIES

Model

Description

G/VSH13018

G/VSH13024

G/VSH13030

G/VSH13036

G/VSH13042

G/VSH13048

G/VSH13060

AFE18-60A

All Fuel Kit

X

X

X

X

X

X

X

OT18-60A

Outdoor Thermostat

X

X

X

X

X

X

X

FSK01A*

Freeze Protection Kit

X

X

X

X

X

X

X

ASC01

Anti Short Cycle Kit

X

X

X

X

X

X

X

TX2N2*

TXV Kit

x

---

---

---

---

---

---

TX3N2*

TXV Kit

x

X

X

X

---

---

---

TX5N2*

TXV Kit

---

---

---

---

X

X

X

OT18-60A

Outdoor Lockout Stat

X

X

X

X

X

X

X

OT/EHR18-60

Emergency Heat relay kit

X

X

X

X

X

X

X

CSR-U-1

Hard Start Kit

X

X

X

X

---

---

---

CSR-U-2

Hard Start Kit

---

---

---

X

X

X

X

CSR-U-3

Hard Start Kit

---

---

---

---

---

X

X

 

 

 

 

 

 

 

 

 

Model

Description

ASH13018

ASH13024

ASH13030

ASH13036

ASH13042

ASH13048

ASH13060

AFE18-60A

All Fuel Kit

X

X

X

X

X

X

X

OT18-60A

Outdoor Thermostat

X

X

X

X

X

X

X

FSK01A*

Freeze Protection Kit

X

X

X

X

X

X

X

ASC01

Anti Short Cycle Kit

X

X

X

X

X

X

X

TX2N2*

TXV Kit

x

---

---

---

---

---

---

TX3N2*

TXV Kit

x

X

X

X

---

---

---

TX5N2*

TXV Kit

---

---

---

---

X

X

X

OT18-60A

Outdoor Lockout Stat

X

X

X

X

X

X

X

OT/EHR18-60

Emergency Heat relay kit

X

X

X

X

X

X

X

CSR-U-1

Hard Start Kit

X

X

X

X

---

---

---

CSR-U-2

Hard Start Kit

---

---

---

X

X

X

X

CSR-U-3

Hard Start Kit

---

---

---

---

---

X

X

 

 

 

 

 

 

 

 

 

Model

Description

ASC13018

ASC13024

ASC13030

ASC13036

ASC13042

ASC13048

ASC13060

OT18-60A

Outdoor Thermostat

---

---

---

---

---

---

---

FSK01A*

Freeze Protection Kit

X

X

X

X

X

X

X

ASC01

Anti Short Cycle Kit

X

X

X

X

X

X

X

TX2N2*

TXV Kit

X

---

---

---

---

---

---

TX3N2*

TXV Kit

x

x

x

x

---

---

---

TX5N2*

TXV Kit

---

---

---

---

X

X

X

CSR-U-1

Hard Start Kit

X

X

X

X

---

---

---

CSR-U-2

Hard Start Kit

---

---

---

X

X

X

X

CSR-U-3

Hard Start Kit

---

---

---

---

---

X

X

 

 

 

 

Model

Description

G/VSC13018

G/VSC13024

G/VSC13030

G/VSC13036

G/VSC13042

G/VSC13048

G/VSC13060

OT18-60A

Outdoor Thermostat

---

---

---

---

---

---

---

FSK01A*

Freeze Protection Kit

X

X

X

X

X

X

X

ASC01

Anti Short Cycle Kit

X

X

X

X

X

X

X

TX2N2*

TXV Kit

X

---

---

---

---

---

---

TX3N2*

TXV Kit

x

x

x

x

---

---

---

TX5N2*

TXV Kit

---

---

---

---

X

X

X

CSR-U-1

Hard Start Kit

X

X

X

X

---

---

---

CSR-U-2

Hard Start Kit

---

---

---

X

X

X

X

CSR-U-3

Hard Start Kit

---

---

---

---

---

X

X

 

 

 

 

 

 

 

 

 

Model

Description

GSC100903

GSC100904

GSC101203

GSC101204

 

 

 

FSK01A*

Freeze Protection Kit

x

x

x

x

 

 

 

ASC01

Anti Short Cycle Kit

x

x

x

x

 

 

 

OT/EHR18-60

Emergency Heat relay kit

---

---

---

---

 

 

 

 

 

 

 

 

 

*Installed on indoor coil.

Model

Description

GSH100903

GSH100904

GSH101203

GSH101204

 

 

 

FSK01A*

Freeze Protection Kit

x

x

x

x

 

 

 

ASC01

Anti Short Cycle Kit

x

x

x

x

 

 

 

OT/EHR18-60

Emergency Heat relay kit

---

---

---

---

 

 

 

16

ACCESSORIES

Model

Description

CPKF24

CPKF36

CPKF42

CPKF48

CPKF60

CPKF61

 

AFE18-60A

All Fuel Kit

x

x

x

x

x

x

 

OT18-60A

Outdoor Thermostat

x

x

x

x

x

x

 

FSK01A*

Freeze Protection Kit

x

x

x

x

x

x

 

ASC01

Anti Short Cycle Kit

x

x

x

x

x

x

 

TX2N2*

TXV Kit

---

---

---

---

---

---

 

TX3N2*

TXV Kit

x

x

---

---

---

---

 

TX5N2*

TXV Kit

---

---

x

x

x

x

 

OT18-60A

Outdoor Lockout Stat

x

x

x

x

x

x

 

OT/EHR18-60

Emergency Heat relay kit

x

x

x

x

x

x

 

CSR-U-1

Hard Start Kit

x

x

---

---

---

---

 

CSR-U-2

Hard Start Kit

---

x

x

x

x

x

 

CSR-U-3

Hard Start Kit

---

---

---

x

x

x

 

 

 

 

 

 

 

 

 

 

Model

Description

CKF24

CKF36

CKF48

CKF60

CKF70

 

 

AFE18-60A

All Fuel Kit

---

---

---

---

---

 

 

OT18-60A

Outdoor Thermostat

---

---

---

---

---

 

 

FSK01A*

Freeze Protection Kit

x

x

x

x

x

 

 

ASC01

Anti Short Cycle Kit

x

x

x

x

x

 

 

TX2N2*

TXV Kit

---

---

---

---

---

 

 

TX3N2*

TXV Kit

x

x

---

---

---

 

 

TX5N2*

TXV Kit

---

---

x

x

---

 

 

OT18-60A

Outdoor Lockout Stat

---

---

---

---

---

 

 

OT/EHR18-60

Emergency Heat relay kit

---

---

---

---

---

 

 

CSR-U-1

Hard Start Kit

x

x

---

---

---

 

 

CSR-U-2

Hard Start Kit

---

x

x

x

---

 

 

CSR-U-3

Hard Start Kit

---

---

x

x

---

 

 

 

 

 

 

 

 

 

 

 

Model

Description

CKL18

CKL24

CKL30

CKL36

CKL42

CKL49

CKL60

AFE18-60A

All Fuel Kit

---

---

---

---

---

---

---

OT18-60A

Outdoor Thermostat

---

---

---

---

---

---

---

FSK01A*

Freeze Protection Kit

x

x

x

x

x

x

x

ASC01

Anti Short Cycle Kit

x

x

x

x

x

x

x

TX2N2*

TXV Kit

x

---

---

---

---

---

---

TX3N2*

TXV Kit

x

x

x

x

---

---

---

TX5N2*

TXV Kit

---

---

---

---

x

x

x

OT18-60A

Outdoor Lockout Stat

---

---

---

---

---

---

---

OT/EHR18-60

Emergency Heat relay kit

---

---

---

---

---

---

---

CSR-U-1

Hard Start Kit

x

x

x

x

---

---

---

CSR-U-2

Hard Start Kit

---

---

---

x

x

x

x

CSR-U-3

Hard Start Kit

---

---

---

---

---

x

x

 

 

 

 

 

 

 

 

 

Model

Description

CE120

 

 

 

 

 

 

AFE18-60A

All Fuel Kit

---

 

 

 

 

 

 

OT18-60A

Outdoor Thermostat

---

 

 

 

 

 

 

FSK01A*

Freeze Protection Kit

x

 

 

 

 

 

 

ASC01

Anti Short Cycle Kit

x

 

 

 

 

 

 

TX2N2*

TXV Kit

---

 

 

 

 

 

 

TX3N2*

TXV Kit

---

 

 

 

 

 

 

TX5N2*

TXV Kit

---

 

 

 

 

 

 

OT18-60A

Outdoor Lockout Stat

---

 

 

 

 

 

 

OT/EHR18-60

Emergency Heat relay kit

---

 

 

 

 

 

 

CSR-U-1

Hard Start Kit

---

 

 

 

 

 

 

CSR-U-2

Hard Start Kit

---

 

 

 

 

 

 

CSR-U-3

Hard Start Kit

---

 

 

 

 

 

 

17

ACCESSORIES

EXPANSION VALVE KITS

1/4 FLARE CONNECTION

 

 

For Applications requiring

 

 

a field installed access fitting

 

 

BULB TO BE LOCATED

 

 

AT 10 OR 2 O'CLOCK

SUCTION LINE

BULB

 

 

 

 

EVAPORATOR COIL

 

 

 

 

 

 

SEAL SUPPLIED W/ KIT

 

PISTON

TAILPIECE

 

 

 

 

SEAL SUPPLIED W/ KIT

 

DISTRIBUTOR

SEAL

 

 

EXPANSION VALVE

 

 

 

BODY

 

 

 

REMOVE BEFORE INSTALLING EXPANSION VALVE

 

 

 

3/8"-

 

 

 

 

 

 

 

 

 

 

SWEAT

 

 

 

7/8" NUT

 

 

1/4' FLARE

 

 

For Applications not requiring

CONNECTION

 

 

a field installed access fitting

 

 

 

 

 

 

BULB TO BE LOCATED

 

 

 

 

 

AT 10 OR 2 O'CLOCK

 

 

 

BULB

SUCTION LINE

 

 

 

 

 

 

 

PISTON

TAILPIECE

EVAPORATOR COIL

 

EXPANSION VALVE

DISTRIBUTOR

SEAL

 

 

 

 

 

 

BODY

 

 

 

 

 

 

 

 

 

 

 

 

3/8"-

 

 

 

 

 

SWEAT

 

REMOVE BEFORE

SEAL SUPPLIED W/ KIT

 

 

 

SEAL SUPPLIED W/ KIT

INSTALLING

 

7/8" NUT

 

 

EXPANSION VALVE

 

 

 

 

 

 

 

 

OT/EHR18-60

OUTDOORTHERMOSTAT&

EMERGENCYHEATRELAY

OT18-60

 

Thermostat

315º

Dial

 

 

COLD (Turn Clockwise)

DEAD

WARM (Turn Counterclockwise)

DIAL

45º

Set Point

Adjustment

Screw Set Point

Indicator

Mark

(Shown @ Oº F)

18

ACCESSORIES

FSK01A

FREEZETHERMOSTAT

KIT

Wire Nut

 

la

c

k

 

B

 

 

 

 

k

 

 

 

 

 

 

c

 

 

 

la

 

 

 

 

B

 

Y

Wire Nut

Y

Install Line

Install Line

Thermostat

Thermostat

Here

Here

 

Black

Wire Nut

Y

 

 

 

 

 

 

 

 

 

 

 

 

 

Bl

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

c

 

 

 

 

 

 

 

 

 

 

 

 

Wire Nut

k

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Y

ASC01A

ANTI-SHORT-CYCLECONTROLKIT

SHORT CYCLE

Y1 R1 PROTECTOR

Y2 R2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

YELLOW 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACTOR

 

 

 

 

 

 

 

 

 

 

 

 

T2

T1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Y

 

BLACK 1

 

 

 

 

THERMOSTAT

 

 

 

 

 

 

 

 

 

 

 

L2 L1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

WIRE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UNIT

 

 

 

 

 

 

 

 

 

BLACK 1

TERMINAL

 

 

 

 

 

 

 

 

 

 

 

BOARD

19

ACCESSORIES

COIL ACCESSORIES

COIL MODEL

TX2N2 TXV KIT

TX3N2 TXV KIT

TX5N2 TXV KIT

FSK01A FREEZE PROTECTION KIT

 

 

 

 

 

CA*F030B4*

---

X

---

X

CA*F036B4*

---

X

---

X

CA*F042C4*

---

---

X

X

CA*F048C4*

---

---

X

X

CA*F057D4*

---

---

X

X

CA*F060D4*

---

---

X

X

CHPF030A4*

---

X

---

X

CHPF036B4*

---

X

---

X

CHPF042A4*

---

---

X

X

CHPF048D4*

---

---

X

X

CHPF060D4*

---

---

X

X

CH36FCB

---

X

---

X

CH48FCB

---

---

X

X

CH60FCB

---

---

X

X

CA*F18246*

X

X

---

X

CA*F30306*

---

X

---

X

CA*F36426*

---

X

X

X

CHPF18246*

X

---

X

X

CHPF30306*

---

---

X

X

CHPF36426*

---

---

X

X

CSCF1824N6*

X

---

---

X

CSCF303N6*

---

X

---

X

CSCF3642N6*

---

X

X

X

 

 

 

 

HKR SERIES ELECTRIC HEAT KITS

 

 

 

 

 

 

 

ELECTRICHEATKITAPPLICATIONS

 

 

 

 

 

 

 

 

 

MBR & MBE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLOWER

 

 

 

 

 

 

ELECTRIC HEAT KIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NO HEAT

HKR-03*

HKR05-(C)'

HKR-06*

 

HKR-08(C)*

HKR-10(C)*

HKR-15(C)*

HKR-20(C)*

HKR-21(C)*

^HKR3-15*

^HKR3-20A

 

 

MBR0800AA-1AA

-

X

X

X

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBR1200AA-1AA

-

X

X

X

 

X

X

X

 

X

X

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBR1600AA-1AA

-

X

X

X

 

X

X

X

 

X

X

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBR2000AA-1AA

-

X

X

X

 

X

X

X

 

X

X

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBE1200AA-1AA

-

-

-

-

 

X

X

X

 

-

-

 

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBE1600AA-1AA

-

-

-

-

 

-

X

X

 

-

-

 

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBE2000AA-1AA

-

-

-

-

 

-

X

X

 

X

-

 

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBE1200AA-1BA

-

X

X

X

 

X

X

X

 

-

-

 

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBE1600AA-1BA

-

X

X

X

 

X

X

X

 

-

-

 

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MBE2000AA-1BA

-

X

X

X

 

X

X

X

 

X

-

 

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X = Allowable combinations

^ = Circuit 1: Single Phase for Air Handler Motor

- = Restricted combinations

Circuit 2: 3-Phase for HKR3 Heater Kits

* = Revision level that my or may not be designated C = Circuit Breaker option

20

PRODUCT DESIGN

This section gives a basic description of cooling unit operation, its various components and their basic operation. Ensure your system is properly sized for heat gain and loss according to methods of the Air Conditioning Contractors Association (ACCA) or equivalent.

CONDENSING UNIT

These units are designed for free air discharge. Condensed air is pulled through the condenser coil by a direct drive propeller fan and then discharged from the cabinet top. The unit requires no additional resistance (i.e. duct work) and should not be added.

The GSH13, GSH14, ASH13 and VSH13 Heat Pump condensing units are designed for 208-230 dual voltage single phase applications. The GSH13 3 ton model is available in 230V, 3 phase applications. The GSH13 4 and 5 ton models are available for 230V, 3-phase and 460V, 3-phase applications.

The units range in size from 1.5 to 5-ton and have a rating of 13 and 14 SEER. SEER efficiency is dependent upon the unit and its components. Refer to the "Technical Information" manual of the unit you are servicing for further details.

The GSC13, GSC14 and ASC13 and VSC13 Condensing Units are made in 1.5 through 5 ton sizes. They are designed for 208-240 volt single phase applications. The GSC13 3 ton model is available in 230V, 3 phase applications. The GSC13 4 and 5 ton models are available for 230V, 3-phase and 460V, 3-phase applications.

Suction and Liquid Line Connections

All units come equipped with suction and liquid valves designed for connection to refrigerant-type copper. Front seating valves are factory-installed to accept the field-run copper. The total refrigerant charge needed for a normal operation is also factory-installed. For additional refrigerant line set information, refer to the "Technical Information" manual of the unit you are servicing.

Compressors

GSC13, VSC13, GSH13 and VSH13 use a mix of reciprocating and scroll compressors, except for the VSC130181AA which uses a rotary compressor. The ASC13 and ASH13 use the Copeland Scroll® Compressor. There are a number of design characteristics which differentiate the scroll compressor from the reciprocating compressor. One is the scroll. A scroll is an involute spiral which, when matched with a mating scroll form, generates a series of crescent-shaped gas pockets between the members (see following illustration). During compression, one scroll remains stationary while the other form orbits. This motion causes the resulting gas pocket to compress and push toward the center of the scrolls. When the center is reached, the gas is discharged out a port located at the compressor center.

GSC130361D* and GSC130481AG use Bristol® BENCHMARK™ compressors, the most advanced compressors in the industry today. The BENCHMARK™ reciprocating compressor can be recognized by a “J” in the fourth character of the compressor model number. Innovative mechanical design and gas management make the BENCHMARK™ compressor very efficient and remarkably quiet. The sound content (frequency) delivers exceptional acoustical characteristics and the virtually round housing design is compact and also helps to reduce the overall sound and vibration.

GSC130181BA use Panasonic® rotary compressors.

COILS AND BLOWER COILS

MBR/MBE blower cabinets are designed to be used as a twopiece blower and coil combination. MBR/MBE blower sections can be attached to cased evaporator coil. This twopiece arrangement allows for a variety of mix-matching possibilities providing greater flexibility. The MBE blower cabinet uses a variable speed motor that maintains a constant airflow with a higher duct static.

It is approved for applications with cooling coils of up to 0.8 inches W.C. external static pressure and includes a feature that allows airflow to be changed by +15%. The MBR blower cabinet uses a PSC motor. It is approved for applications with cooling coils of up to 0.5 inches W.C. external static pressure.

The MBR/MBE blower cabinets with proper coil matches can be positioned for upflow, counterflow, horizontal right or horizontal left operation. All units are constructed with R-4.2 insulation. In areas of extreme humidity (greater than 80% consistently), insulate the exterior of the blower with insulation having a vapor barrier equivalent to ductwork insulation, providing local codes permit.

The CAPX/CHPX coils are equipped with a thermostatic expansion valve that has a built-in internal check valve for refrigerant metering. The CACF/CAPF/CHPF coils are equipped with a fixed restrictor orifice.

21

Loading...
+ 48 hidden pages