CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Model No. GLSY22522
Serial No.
Write the serial number in the
space above for future reference.
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfaction through direct assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
USER’S MANUAL
Serial Number Decal (Under Seat)
2
WARNING DECAL PLACEMENT
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: APART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly.
TRACKER, a registered trademark of Galyan’s Nevada Inc., East Main St., Plainfield, IN 46168
TABLE OF CONTENTS
The decals shown here have been placed on the
weight system. If a decal is missing or illegible,
please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time, to
order a free replacement decal. Apply the decal
in the location shown.
Decal 1
Decal 2–
This decal is on the finger guards
on both sides of the weight bench.
Decal 1
Decal 2
!
WARNING
• Misuse of this
product may result in
serious injury.
• Read user’s manual
and follow all warnings
and operating instructions prior to use.
• Do not allow children
on or around machine.
• Replace label if
damaged, illegible,
or removed.
Keep hands and
fingers clear of
this area.
1. Read all instructions in this manual before
using the weight system. Use the weight system only as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight system are adequately informed of all precautions.
3. The weight system is intended for home use
only. Do not use the weight system in any
commercial, rental, or institutional setting.
4. Use the weight system only on a level surface. Cover the floor beneath the weight system to protect the floor.
5. Make sure all parts are properly tightened
each time you use the weight system.
Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the weight system at all times.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protection while exercising.
9. Make sure that the cables remain on the pulleys at all times. If the cables binds as you
are exercising, stop immediately and make
sure that the cables are on the pulleys.
10. Always set both safety spotters at the same
height.
11. The weight system is designed to support a
maximum user weight of 250 pounds, and a
maximum total weight of 560 pounds. Do not
place more than 310 pounds on the barbell.
Do not place more than 150 pounds on the
weight carriage or the leg lever. Note: The
weight system does not include weights.
12. Always place an equal amount of weight on
each side of the weight carriage or barbell.
13. Always secure the weights with the weight
clips when they are mounted on the weight
carriage.
14.
Always exercise with a partner. Your partner
should be ready to catch the barbell if you
cannot complete a repetition.
15. Always move the bench out of the way when
performing squat exercises. Always disconnect the lat bar from the cable when performing an exercise that does not require it.
16. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
WARNING:Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
WARNING: To reduce the risk of serious injury, read the following important precautions
before using the weight system.
IMPORTANT PRECAUTIONS
3
ASSEMBLED
DIMENSIONS:
Height: 84 in.
Width: 83 in.
Depth: 96 in.
4
Weight Carriage
Upright
Smith Bar Guide
Safety Spotter
Locking Bar
Barbell
Butterfly Arm
Backrest Bracket
Right Side
Left Side
Note: The terms “right side” and “left side” are determined relative to a person sitting on the
bench; they do not correspond to right and left on the drawings in the manual.
Curl Pad
Backrest
Foot Plate
Leg Lever
Seat
Lat Bar
BEFORE YOU BEGIN
Thank you for selecting the versatile TRACKER®735
POWER SMITH SYSTEM weight system. The weight
system is designed to help you develop every major
muscle group of the body. Whether your goal is a
shapely figure, dramatic increase in muscle size and
strength, or a healthier cardiovascular system, the 735
POWER SMITH SYSTEM weight system will help you
achieve the specific results you want.
For your benefit, read this manual carefully before
using the weight system. If you have additional ques-
tions, please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is GLSY22522. The serial number can be
found on a decal attached to the weight system (see
the front cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
5
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires two people.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• As you assemble the weight system, make sure
all parts are oriented as shown in the drawings.
• For help identifying small parts, use the
PART
IDENTIFICATION CHART.
The following tools (not included) are required
for assembly:
•Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight system can be assembled successfully by anyone. However, it is important to
realize that the versatile weight system has
many parts and that the assembly process will
take time. Most people find that by setting aside
plenty of time, assembly will go smoothly.
ASSEMBLY
1.
Press a 51mm x 76mm Inner Cap (21) into the
Front Leg (4). Attach two Stabilizer Feet (22) to
the Front Stabilizer (3) with four M4 x 16mm
Screws (103).
Attach the Front Leg (4) to the Front Stabilizer (3)
with four M10 x 72mm Bolts (116), two Leg Plates
(41), and four M10 Nylon Locknuts (32). Do not
tighten the Locknuts yet.
2. Attach two Stabilizer Feet (22) to the Rear
Stabilizer (1) with four M4 x 16mm Screws (103).
Attach the two Wheels (38) to the Rear Stabilizer
(1) with two M10 x 45mm Bolts (27) and two M10
Nylon Locknuts (32). Do not overtighten the
Locknuts; the Wheels must be able to roll
easily.
Attach the Bench Frame (2) to the Rear Stabilizer
(1) with two M10 x 68mm Bolts (26), two M10
Washers (100), and two M10 Nylon Locknuts
(32). Make sure the decal is in the indicated
position. Do not tighten the Locknuts yet.
1
2
32
32
116
103
22
22
41
41
4
3
21
32
32
32
38
38
100
26
27
1
27
2
22
22
103
103
Decal
103
Before beginning assembly, make sure you
understand the information in the box
above.
6
5. Attach the Backrest (10) to the Backrest Frames
(6) with four M6 x 53mm Bolts (29) and four M6
Washers (37). Note: If the four Bolts cannot be
inserted into the Backrest properly, go back to
step 4 and readjust the Backrest Frames.
4. Press four 20mm x 40mm Inner Caps (20) into
the ends of the two Backrest Frames (6).
Attach the Backrest Frames (6) to the Backrest
Bracket (9) with four M10 x 58mm Bolts (33), four
M10 Washers (100), and four M10 Nylon
Locknuts (32). Make sure the Backrest Frames
are oriented as shown. The Backrests Frames
must be parallel, with the indicated holes
aligned.
3
4
5
39
34
34
39
2
4
32
18
100
100
33
33
32
37
29
37
29
6
10
20
20
6
Holes
9
3. Press two Bushings (34) into the Bench Frame
(2).
Attach the Bench Frame (2) to the Front Leg (4)
with four M10 x 94mm Bolts (18), two Joint Plates
(39), and four M10 Nylon Locknuts (32). Do not
tighten the Locknuts yet.
31
37
32
29
30
15
7
6. Press four Bushings (34) into the Backrest
Frames (6) as shown.
Secure the Backrest Knob (25) to the Bench
Frame (2). Pull the Knob out as far as it will go.
Slide the Backrest Bracket (9) between the Bench
Frame tubes and engage the Knob into a hole in
the Bracket.
Attach the Backrest Frames (6) and two Finger
Guards (14) to the Bench Frame (2) with an M10
x 146mm Bolt (35), two M10 Washers (100), and
an M10 Nylon Locknut (32). Make sure the
decals are on the outside of the Finger
Guards. Do not overtighten the Locknut; the
Bracket Frames and Finger Guards must be
able to pivot easily.
8. Press two Bushings (34) into the Seat Frame (5)
as shown.
Attach the Seat Frame (5) to the Backrest
Frames (6) and Finger Guards (14) with an M10 x
146mm Bolt (35), two Short Spacers (36), and an
M10 Nylon Locknut (32). Do not overtighten the
Locknut; the Seat Frame must be able to pivot
easily.
Attach the Pivot Bracket (15) to the Bench Frame
(2) with an M10 x 100mm Bolt (28) and an M10
Nylon Locknut (32). Do not overtighten the
Locknut; the Pivot Bracket must be able to
pivot easily.
Tighten the M10 Nylon Locknuts (32) used in
steps 1–3.
7. Press a 38mm x 50mm Inner Cap (112) into the
indicated end of the Seat Frame (5). Press two
Bushings (34) into the Seat Frame as shown.
Attach the Pivot Bracket (15) to the Seat Frame
(5) with an M10 x 75mm Bolt (30) and an M10
Nylon Locknut (32). Do not overtighten the
Locknut; the Pivot Bracket must be able to
pivot easily.
Attach the Seat (11) to the Seat Frame (5) with
two M6 x 16mm Bolts (31), an M6 x 53mm Bolt
(29), and an M6 Washer (37).
6
7
8
100
100
35
Decal
9
25
2
5
34
36
36
32
28
6
14
35
32
15
2
34
11
112
5
34
34
32
34
6
34
34
14
6
8
9. Press three 50mm Square Inner Caps (88) into
the Leg Lever (7). Press a 48mm Round Inner
Cap (23) into the tube on the Leg Lever.
Slide the two Pad Tubes (16) into the Leg Lever
(7). Slide four Foam Pads (17) onto the ends of
the Pad Tubes. Press four 19mm Round Inner
Caps (19) into the ends of the Pad Tubes.
11. Press a 45mm Square Inner Cap (80) into the
bottom of the Curl Post (12).
Attach the Curl Pad (13) to the Curl Post (12) with
two M6 x 16mm Screws (31).
10. Press two Bushings (34) into the Leg Lever
Bracket (8) as shown.
Attach the Leg Lever (7) to the Leg Lever Bracket
(8) with an M10 x 78mm Bolt (40) and an M10
Nylon Locknut (32). Do not overtighten the
Locknut; the Leg Lever must be able to pivot
easily.
Loosen the Seat Knob (24). Secure the Leg Lever
Bracket (8) in the end of the Seat Frame (5) with
the Knob.
9
10
11
88
17
17
17
17
19
7
88
88
23
19
19
19
7
8
32
24
5
40
34
13
31
12
80
16
16
9
12. Locate the Base (49) with the warning decal
attached to it. Attach two Base Feet (71) to the
Base with four M4 x 16mm Screws (103).
Attach the Base (49) to the indicated side of the
Center Base (48) with two M10 x 78mm Bolts
(40), two M10 Washers (100), and two M10 Nylon
Locknuts (32). Do not tighten the Locknuts yet.
Attach the Center Base (48) to the other Base
(49) in the same manner.
Insert two M10 x 75mm Carriage Bolts (102) up
through the Center Base (48).
13. Press a 60mm Square Inner Cap (82) into the
back of the Rear Base (44).
Attach the Rear Upright (46) to the Center Base
(48) with the two M10 x 75mm Carriage Bolts
(102) and two M10 Nylon Locknuts (32). Do not
tighten the Locknuts yet.
Attach the Foot Plate (45) and the Rear Base
(44) to the Center Base (48) with two M10 x
82mm Bolts (87) and two M10 Nylon Locknuts
(32). Do not tighten the Locknuts yet.
12
13
87
48
40
40
49
49
102
71
103
71
Decal
103
32
100
32
32
32
44
102
48
45
82
46
10
15. Attach a Smith Bar Guide (50) to a Base (49) with
an M10 x 78mm Bolt (40), two M10 Washers
(100), two 17mm Spacers (89), and an M10
Nylon Locknut (32). Do not tighten the
Locknuts yet.
Attach an Upright (42) to the Base (49) with four
M10 x 78mm Bolts (40), two Angled Rack Joint
Plates (70), and four M10 Nylon Locknuts (32).
Note: The indicated corners of the Joint
Plates are less than 90 degrees. Do not tighten the Locknuts yet.
Attach the other Smith Bar Guide (50) and
Upright (42) to the other Base (49) in the same
manner.
14
15
108
26
44
55
55
111
23
43
49
70
This corner is
not a right angle
40
40 100
100
89
32
32
50
42
70
32
81
100
100
52
14. See the inset drawing. Insert an M10 x 19mm
Bolt (111) into the bracket on the Weight Carriage
(55).
Press two 48mm Round Inner Caps (23) into the
Weight Carriage (55).
Orient the Weight Carriage (55) and Lat Tower
(43) as shown. Slide the Weight Carriage onto
the Lat Tower. Orient the Carriage Stop (52) as
shown and slide it onto the Lat Tower. Attach the
Carriage Stop at the indicated hole with an M8 x
70mm Bolt (108) and an M8 Nylon Locknut (81).
Attach the Lat Tower (43) to the Rear Base (44)
with two M10 x 68mm Bolts (26), four M10
Washers (100), and two M10 Nylon Locknuts
(32). Do not tighten the Locknuts yet.
23
The front edge
is taller than
the rear edge
11
16. Press two 38mm Bushings (74) into the Left
Weight Glider (62). Attach the Left Spotter Hook
(76) to a Safety Spotter (64) with an M10 x 25mm
Bolt (105) and an M10 Nylon Locknut (32). Do
not overtighten the Locknut; the Spotter Hook
must be able to pivot easily.
Slide the Safety Spotter (64) onto the left Smith
Bar Guide (50) and engage the Left Spotter Hook
(76) into a slot in the Upright (42). Slide the Left
Weight Glider (62) onto the Smith Bar Guide and
rest it on top of the Safety Spotter. Make sure all
parts are oriented as shown.
Repeat this step with the right Weight Glider
(not shown) and the Right Spotter Hook (not
shown).
17. Press two 50mm Square Inner Caps (88) into the
Butterfly Arm Bracket (68).
Attach the Butterfly Arm Bracket (68) to the Rear
Upright (46) with two M10 x 68mm Bolts (26), two
M10 Washers (100), and two M10 Nylon
Locknuts (32). Do not tighten the Locknuts yet.
18. Press two 60mm Square Inner Caps (82) into the
ends of the Top Frame (51).
Attach the Top Frame (51) to an Upright (42) with
four M10 x 78mm Bolts (40), a Front Rack Joint
Plate (115), a Rear Rack Joint Plate (86), and
four M10 Nylon Locknuts (32). Note: The indi-
cated corner of the Front Rack Joint Plate is
90 degrees. The Rear Rack Joint Plate has a
notch in it. Do not tighten the Locknuts yet.
Attach the Top Frame (51) to a Smith Bar Guide
(50) with an M13 x 25mm Screw (113). Do not
tighten the Screw yet.
Attach the Top Frame (51) to the other Upright
(42) and Smith Weight Guide (50) in the same
manner.
16
18
17
62
74
64
74
105
76
32
50
42
51
82
40
86
42
50
32
100
100
68
32
32
46
88
88
26
115
113
This corner is
a right angle
12
19. Press two 50mm Square Inner Caps (88) into the
ends of the Pulley Bar (47).
Attach the Pulley Bar (47) inside the Lat Tower
(43) with two M10 x 68mm Bolts (26), four M10
Washers (100), and two M10 Nylon Locknuts
(32). Do not tighten the Locknuts yet.
Attach the Pulley Bar (47) to the Rear Upright
(46) and the Butterfly Arm Bracket (68) with four
M10 x 68mm Bolts (26), four M10 Washers (100),
and four M10 Nylon Locknuts (32). Do not tight-
en the Locknuts yet.
Attach the Pulley Bar (47) to the Top Frame (51)
with two M10 x 78mm Bolts (40), two M10
Washers (100), and two M10 Nylon Locknuts (32).
Tighten the M10 Nylon Locknuts (32) used in
steps 12–15 and 17–19.
21. Route the Medium Cable (94) up through the
Pulley Bar (47) and around an 89mm Pulley (90).
Attach the Pulley inside the Pulley Bar with an
M10 x 68mm Bolt (26), two M10 Washers (100),
two 12mm Spacers (110), and an M10 Nylon
Locknut (32).
20. Press two 45mm Square Inner Caps (80) into the
Right Butterfly Arm (56). Wet the bottom end of
the Arm with soapy water and slide a Foam Pad
(69) onto the Arm.
Lubricate the axles on the Butterfly Arm Bracket
(68) with grease. Attach the Right Butterfly Arm
(56) to the indicated axle with two 25mm Retainer
Rings (98) and a 25mm Round Outer Cap (99).
Note: Place the Retainer Rings on top of the
included retainer tool, as shown in the inset
drawing. Make sure the teeth on the Retainers
bend toward the tool. Gently tap the tool onto
the axle. Remove the tool, and tap the Outer
Cap onto the axle.
Assemble the Left Butterfly Arm (57) in the
same manner.
19
20
21
47
26
43
46
68
100
32
32
32
100
32
88
100
100
51
32
100
26
26
40
56
80
69
57
80
68
Bracket
Lubricate
Axle
Axle
99
Retainer
Tool
98
98
32
90
47
94
110
100
26
88
110
100
13
23. Route the Medium Cable (94) up through the
Pulley Bar (47), around an 89mm Pulley (90) and
back down through the Pulley Bar. Attach the
Pulley inside the Pulley Bar with an M10 x 68mm
Bolt (26), two M10 Washers (100), two 12mm
Spacers (110), and an M10 Nylon Locknut (32).
25. Attach the Short Cable (95) to the Left Butterfly
Arm (57) with an M8 x 21mm Shoulder Bolt (114)
an M8 Nylon Locknut (81).
24. Attach the Medium Cable (94) to the M10 x
19mm Bolt (111) in the Weight Carriage (55) with
an M10 Nylon Locknut (32).
23
24
25
32
94
47
90
55
94
32
95
114
81
57
111
100
100
110
110
26
22. Route the Medium Cable (94) over an 89mm
Pulley (90) and down through the Pulley Bar (47).
Attach the Pulley inside the Pulley Bar with an
M10 x 68mm Bolt (26), two M10 Washers (100),
two 12mm Spacers (110), and an M10 Nylon
Locknut (32).
22
94
90
32
47
100
100
26
110
110
14
27. Wrap the Short Cable (95) around a “V”-Pulley
(91). Attach the Pulley and a Large Cable Trap
(92) to the bracket on the Rear Upright (46) with
an M10 x 60mm Bolt (101) and an M10 Nylon
Locknut (32).
27
101
92
91
32
95
46
28. Attach the Short Cable (95) to the Right Butterfly
Arm (56) with an M8 x 21mm Shoulder Bolt (114)
an M8 Nylon Locknut (81).
28
114
95
81
56
29. Route the end of the Long Cable (96) through the
Foot Plate (45) and Rear Upright (46). Attach an
89mm Pulley (90) inside the Upright with an M10
x 68mm Bolt (26), two M10 Washers (100), two
12mm Spacers (110), and an M10 Nylon Locknut
(32).
29
90
96
32
26
45
46
100
100
110
110
26. Wrap the Short Cable (95) around a “V”-Pulley
(91). Attach the Pulley and a Large Cable Trap
(92) to the bracket on the Rear Upright (46) with
an M10 x 60mm Bolt (101) and an M10 Nylon
Locknut (32).
26
92
95
32
91
46
101
15
31. Wrap the Long Cable (96) around an 89mm
Pulley (90). Attach the Pulley to the bracket on
the Rear Base (44) with an M10 x 45mm Bolt (27)
and an M10 Nylon Locknut (32).
33. Attach the end of the Long Cable (96) inside the
Rear Base (44) with an M10 x 78mm Bolt (40),
two M10 Washers (100), two 28mm Spacers
(109), and an M10 Nylon Locknut (32).
32. Pull the Medium Cable (94) down between the
indicated 89mm Pulleys (90). Hold an 89mm
Pulley inside the Cable and attach it and a Cable
Trap (93) to the single set of holes in the Pulley
Plates (79) with an M10 x 45mm Bolt (27) and an
M10 Nylon Locknut (32). Make sure the Cable
Trap is oriented to hold the Cable in the
groove of the Pulley.
Wrap the Long Cable (96) around an 89mm
Pulley (90). Attach the Pulley and a Cable Trap
(93) to the second set of holes from the bottom of
the Pulley Plates (79) with an M10 x 45mm Bolt
(27) and an M10 Nylon Locknut (32). Make sure
the Cable Trap is oriented to hold the Cable in
the groove of the Pulley.
31
32
33
30. Pull the Short Cable (95) down between the two
“V”-Pulleys (91). Hold an 89mm Pulley (90) inside
the Cable and attach it to the Double “U”-Bracket
(78) with an M10 x 45mm Bolt (27) and an M10
Nylon Locknut (32).
Wrap the Long Cable (96) around an 89mm
Pulley (90). Attach the Pulley to the bottom of the
Double “U”-Bracket (78) with an M10 x 45mm
Bolt (27) and an M10 Nylon Locknut (32).
30
27
32
78
32
27
90
90
95
96
96
90
27
44
32
27
79
90
90
94
90
96
93
93
79
32
44
96
100
100
40
109
109
32
91
16
35. Press a 48mm Bushing (75) into the end of a
Weight Adapter (72). Slide the Weight Adapter
onto the end of the Barbell (61) and secure it in
place with a Large Washer (106) and an M10 x
25mm Button Head Bolt (65).
Attach the other Weight Adapter (72) to other
side of the Barbell (61) in the same manner.
Fully tighten the M8 x 19mm Screws (107) into
the Left and Right Weight Gliders (62, 63).
37. Wet the ends of the Lat Bar (59) with soapy
water. Slide two Handgrips (60) onto the ends of
the Lat Bar.
38. Make sure that all parts are properly tightened
before you use the weight system. The use of
all remaining parts will be explained in
ADJUSTMENTS starting on the next page.
36. Attach the Rack Backrest (67) to the Rear Upright
(46) with two M6 x 63mm Screws (104) and two
M6 Washers (37).
35
36
37
34. Slide the Barbell (61) through the Left Weight
Glider (62), the Locking Bar (58), and the Right
Weight Glider (63). Make sure the Locking Bar
is oriented as shown.
Turn the Locking Bar (58) so that the hooks
engage slots in the Uprights (not shown).
34
61
62
58
63
61
107
59
60
60
72
75
106
65
104
104
46
67
37
37
This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
17
ADJUSTING THE BACKREST
To adjust the position of the Backrest (10), pull the
Backrest Knob (25) out as far as it will go. Move the
Backrest to the desired position, and engage the
Knob into a hole in the Backrest Bracket (9).
10
7
8
5
12
7
9
25
Adjustment
Holes
ATTACHING THE LEG LEVER OR CURL PAD
To use the Leg Lever (7), insert the Leg Lever
Bracket (8) into the Seat Frame (5). Secure the
Bracket with the Seat Knob (24).
To use the Curl Pad (13), insert the Curl Post (12)
into the Seat Frame (5). Secure the Curl Post with the
Seat Knob (24).
ADDING WEIGHT TO THE LEG LEVER
To use the Leg Lever (7), slide the desired amount of
weight (not included) onto the tube on the Leg Lever.
24
13
ADJUSTMENTS
WARNING:
Do not place more than
150 pounds on the Leg Lever (7).
18
42
63
64
94
66
59
77
58
ATTACHING THE LAT BAR
Attach the Lat Bar (59) to the Medium Cable (94) with
a Cable Clip (66). For some exercises, it may be necessary to attach the Chain (not shown) between the
Cable and the Lat Bar with two Cable Clips. Adjust
the length of the Chain between the Lat Bar and
the Cable so the Lat Bar is in the correct starting
position for the exercise to be performed.
Attach the Strap (not shown) to a cable in the same
manner.
85
55
72
61
85
ADDING WEIGHT TO THE WEIGHT RACK
To use the Weight Carriage (55), slide the desired
amount of weight (not included) onto the weight
tubes. Secure the weight with two Large Weight Clips
(85).
To use the Barbell (61), slide the desired amount of
weight (not included) onto the Weight Adapters (72).
Secure the weight with two Large Weight Clips (85).
WARNING:Always place the same
amount of weight on each Weight Carriage (55)
or Barbell (61) and secure the weight with the
two Large Weight Clips (85).
USING THE LOCKING BAR AND SAFETY
SPOTTERS
Before starting an exercise, position the Locking Bar
(58) and the Safety Spotters (64) in the correct position for that exercise.
To do this, grip the Locking Bar (58) with both hands.
Turn the Locking Bar until the two hooks disengage
the slots in the Uprights (42). Move the Locking Bar
to a new position and turn the Locking Bar until the
hooks engage the slots in the Uprights. Note: Always
start an exercise with the Locking Bar positioned
at the lowest point to which it will move during
the exercise.
Position both Safety Spotters (64) directly under the
Weight Gliders (62, 63). To move a Safety Spotter,
grip the handle on the Spotter Hook (76, 77) and pull
the Spotter Hook out of the slot in the Upright (42).
Raise or lower the Safety Spotter to a new position
and turn the Spotter Hook until it engages a slot in
the Upright.
WARNING:Always set both Safety
Spotters (76, 77) at the same height.
19
56
57
10
55
USING THE BUTTERFLY ARMS
To use the Butterfly Arms (56, 57), place the weight
bench, with the Backrest (10) in the level position
(see ADJUSTING THE BACKREST on page 17), next
to the Rear Upright (46). Place the desired amount of
weight on the Weight Carriage (55) (see ADDING
WEIGHT TO THE WEIGHT RACK on the previous
page.)
20mm x 40mm Inner Cap (20)
)
38mm x 50mm Inner Cap (112)
19mm Round Inner Cap (19)
25mm Round Outer Cap (99)
48mm Round Inner Cap (23)
60mm Square Inner Cap (82)
51mm x 76mm Inner Cap (21
45mm Square Inner Cap (80)
50mm Square Inner Cap (88)
PART IDENTIFICATION CHART—Model No. GLSY22522 R0903A
M10 x 68mm Bolt (26)
M10 x 72mm Bolt (116)
M10 x 75mm Carriage Bolt (102)
M10 x 75mm Bolt (30)
M10 x 19mm Bolt (111)
M10 x 25mm Bolt (105)
M10 x 45mm Bolt (27)
M10 x 58mm Bolt (33)
M10 x 78mm Bolt (40)
M10 x 82mm Bolt (87)
M10 x 94mm Bolt (18)
M10 x 100mm Bolt (28)
M10 x 60mm Bolt (101)
M10 x 146mm Bolt (35)
M8 Nylon Locknut (81)
M4 x 16mm Screw (103)
M10 Nylon Locknut (32)
M6 x 16mm Bolt (31)
M6 x 53mm Bolt (29)
M8 x 70mm Bolt (108)
M6 x 63mm Screw (104)
M8 x 19mm Screw (107)
M13 x 25mm Screw (113)
M8 x 21mm Shoulder Bolt (114)
M10 x 25mm Button Head Bolt (65)
M6 Washer (37)
25mm Retainer Ring (98)
M10 Washer (100)
Large Washer (106)
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
PART LIST—Model No. GLSY22522 R0903A
11Rear Stabilizer
21Bench Frame
31Front Stabilizer
41Front Leg
51Seat Frame
62Backrest Frame
71Leg Lever
81Leg Lever Bracket
91Backrest Bracket
10 1 Backrest
11 1 Seat
12 1 Curl Post
13 1 Curl Pad
14 2 Finger Guard
15 1 Pivot Bracket
16 2 Pad Tube
17 4 Foam Pad
18 4 M10 x 94mm Bolt
19 4 19mm Round Inner
Cap
20 4 20mm x 40mm Inner
Cap
21 1 51mm x 76mm Inner
Cap
22 4 Stabilizer Foot
23 3 48mm Round Inner
Cap
24 1 Seat Knob
25 1 Backrest Knob
26 16 M10 x 68mm Bolt
27 7 M10 x 45mm Bolt
28 1 M10 x 100mm Bolt
29 5 M6 x 53mm Bolt
30 1 M10 x 75mm Bolt
31 4 M6 x 16mm Bolt
32 74 M10 Nylon Locknut
33 4 M10 x 58mm Bolt
34 12 Bushing
35 2 M10 x 146mm Bolt
36 2 Spacer
37 7 M6 Washer
38 2 Wheel
39 2 Joint Plate
40 26 M10 x 78mm Bolt
41 2 Large Joint Plate
42 2 Upright
43 1 Lat Tower
44 1 Rear Base
45 1 Foot Plate
46 1 Rear Upright
47 1 Pulley Bar
48 1 Center Base
49 2 Base
50 2 Smith Bar Guide
51 1 Top Frame
52 1 Carriage Stop
53 1 Carriage Stop
Bushing
54 2 Carriage Bushing
55 1 Weight Carriage
56 1 Right Butterfly Arm
57 1 Left Butterfly Arm
58 1 Locking Bar
59 1 Lat Bar
60 2 Handgrip
61 1 Barbell
62 1 Left Weight Glider
63 1 Right Weight Glider
64 2 Safety Spotter
65 2 M10 x 25mm Button
Head Bolt
66 2 Cable Clip
67 1 Rack Backrest
68 1 Butterfly Arm Bracket
69 2 Foam Pad
70 4 Angled Rack Joint
Plate
71 4 Base Foot
72 2 Weight Adapter
73 8 45mm Square
Bushing
74 4 38mm Bushing
75 2 48mm Bushing
76 1 Left Spotter Hook
77 1 Right Spotter Hook
78 1 Double “U”-Bracket
79 2 Pulley Plate
80 5 45mm Square Inner
Cap
81 3 M8 Nylon Locknut
82 3 60mm Square Inner
Cap
83 1 Chain
84 1 Handle
85 2 Large Weight Clip
86 2 Rear Rack Joint Plate
87 2 M10 x 82mm Bolt
88 7 50mm Square Inner
Cap
89 4 17mm Spacer
90 9 89mm Pulley
91 2 “V”-Pulley
92 2 Large Cable Trap
93 2 Cable Trap
94 1 Medium Cable
95 1 Short Cable
96 1 Long Cable
97 4 Butterfly Bushing
98 4 25mm Retainer Ring
99 2 25mm Round Outer
Cap
100 42 M10 Washer
101 2 M10 x 60mm Bolt
102 2 M10 x 75mm
Carriage Bolt
103 16 M4 x 16mm Screw
104 2 M6 x 63mm Screw
105 2 M10 x 25mm Bolt
106 2 Large Washer
107 2 M8 x 19mm Screw
108 1 M8 x 70mm Bolt
109 2 28mm Spacer
1108 12mm Spacer
111 1 M10 x 19mm Bolt
1121 38mm x 50mm inner
Cap
1132 M13 x 25mm Screw
1142 M8 x 21mm Shoulder
Bolt
1152 Front Rack Joint
Plate
1164 M10 x 72mm Bolt
# 1 User’s Manual
# 1 Exercise Guide
#1Retainer Tool
Key
No. Qty. Description
Key
No. Qty. Description
Key
No. Qty. Description
REMOVE THIS PART IDENTIFICATION CHART AND PART LIST/
EXPLODED DRAWING. SAVE THIS PART IDENTIFICATION CHART
AND PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE.
13
24
11
21
17
5
29
12
32
34
37
4
15
88
80
36
31
34
17
34
31
41
23
112
36
30
28
7
20
100
34
32
14
32
34
88
88
100
34
20
35
32
14
37
34
29
19
16
10
9
33
100
37
6
32
16
19
25
8
40
17
17
33
20
6
37
37
29
2
103
116
22
3
41
22
32
39
103
34
39
34
22
18
26
27
103
38
32
100
1
103
32
32
38
27
22
EXPLODED DRAWING—Model No. GLSY22522 R0903A
23
26
111
55
54
100
54
43
100
26
82
108
52
40
44
100
27
109
94
88
100
23
90
90
26
114
95
97
114
32
86
113
32
32
110
100
32
32
100
26
100
40
90
57
95
97
80
81
97
98
56
66
59
60
26
110
93
90
100
110
79
32
47
100
110
100
32
81
97
99
98
99
80
32
32
113
51
100
27
79
93
90
92
101
26
110
94
88
69
60
73
64
76
86
82
115
77
73
32
64
32
101
92
91
32
32
32
91
68
32
88
100
32
90
32
80
69
72
75
106
32
65
73
105
40
105
73
100
104
37
88
100
26
27
78
90
27
74
73
63
74
53
96
81
100
32
46
58
73
107
90
100
104
32
37
67
50
42
50
109
106
75
72
61
71
71
100
32
32
26
49
100
103
100
110
40
48
40
110
90
40
96
62
73
74
74
107
103
32
100
49
100
40
70
40
70
40
100
102
45
87
73
84
83
32
32
100
70
89
89
71
103
40
40
89
32
32
32
40
65
85
100
82
115
40
42
100
89
32
70
32
71
103
Part No. 197090 R0903A Printed in China © 2003 ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage
or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above
is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information when calling:
• The MODEL NUMBER of the product (GLSY22522)
• The NAME of the product (TRACKER
®
735 POWER SMITH SYSTEM weight system)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING in the center of this manual)
ORDERING REPLACEMENT PARTS
Loading...